CME - can not dail PSTN (out going calls )

hello ,
i have CME installed on 2900 router , incomming calls are working fine but i can dial PSTN calls.
below error is comming in Debug:
Outgoing call from gateway: gives diconnect cause value = 34 no circuit

Hi Aslam,
1.Could you please explain the complete network topology and please upload the debugs that you collected with the called and the calling number.Also attach the relevant controller config, serial interface config, dial-peer etc to analyze.
2.Cause value 34 implies that there is a mismatch in channel mapping either on your end or the provider's end.
3.So we need to check if we are sending this error message or if we are receiving this error message.
If we are receiving this error message, then provider needs to correct the channel mapping on their end.
4.If we are using H323 then try to change the isdn channel order using this command on gateway
"isdn bchan-number-order" as well as try changing the channel order from under the gateway on CUCM, if we have a CUCM in the network topology.
5.Make sure we have configured only those channels that we are allowed to inside a Controller for pri group command.
Thanks & Regards,
Mudit Mathur

Similar Messages

Out going caller I.D still not changed

how can i change my out going caller I.D, i have called and emailed, i was even assured that it would be changed, still waiting, mean while my freinds and family are ignoring my calls, the name in question is foreign to them

We've called Verizon at least 7 times and asked them to correct this problem. Everyone has a different answer. Today, they said we needed to take the batteries out of all of our landline phones to "clear the memory" and that would fix it. Still not fixed. I don't think anybody at Verizon knows how to change the caller ID banner !

After update to IOS 4.3.5 my Iphone incoming and out going calls is not working properly and I have to remove the SIM regulerly to conduct or receive a call

after update to IOS 4.3.5 my Iphone incoming and out going calls is not working properly and I have to remove the SIM regulerly to conduct or receive a call
It is not practicale to do this always any one faces the same problem

There may be a problem with the SIM card. Get a new SIM card from your carrier - there should be no charge for a replacement.
If no change with a new SIM card, the standard troubleshooting steps in order are:
Power your iPhone off and on.
An iPhone reset, which is done by pressing and holding the home button and the sleep/wake or on/off button simultaneously until you see the Apple logo and then release.
Restore your iPhone with iTunes from your iPhone's backup.
Restore your iPhone with iTunes as a new iPhone or not from your iPhone's backup.
If no change after any of these steps in order, your iPhone has a hardware problem.

Why do out going call take so long to connect?

Sometime it can take up to 3 minutes for an out going call to connect. It does not seem to matter how many bars I have or where I am.

Thanks for you reply. I would love it if my outgoing calls would connect faster. Yesterday it took 5 minutes to connect.
I have am LG spectrum running VS93022A firmware, Android version 4.1.2. I did have a lot of recent calls stored, so I deleted all of them and them I removed my battery and reinstalled it. Finally, I ran a software update check. All these activities seem to have fixed the problem. I now takes only seconds for a call to connect.thanks!Susan
>> Personal information/e-mail reply/headers removed to comply with the Verizon Wireless Terms of Service <<
Edited by: Verizon Moderator

I can not establish more then 1 call at the same time

Hi,
I have SPA9000 with four active accounts. I can not establish more then 1 call at the same time. Accounts are all in registered state. The field in SIP tab, Default Group Line:, is by default: 1,2,3,4 which means if line 1 is busy try the next one in the order ( in this case number 2). But this is not happening. It always tries to dial out with the first line (account). There is no problem with the provider and I don't want to specify groups of userID's and to assign them special line for dialing out.( by the way in this way it is possible to establish more parallel calls, but then each user will always have to dial thru specific line only). Please help me to find out if the SPA is faulty or give me some workaround, so that when I try to make a call , if one line is busy to dial out thru the next available.
P.S. I suspect that SPA9000 does not notice when the line is busy or not. Maybe there is some issue with the Control Timer Values (sec) on Regional tab.
Thanks,

no it can only be one person at a time

I have a Power Mac G5 Dual 2.3 running 10.5.8, I understand that I can not upgrade to Lion, so what will happen to my Mobile me, which I can not live with out?

I have a Power Mac G5 Dual 2.3 running 10.5.8, I understand that I can not upgrade to Lion, so what will happen to my Mobile me, which I can not live with out? Also will I be able to get Icloud to work?

Hi Mary, the other so called "Features" of iClound will not work for like Syncing, but eMail will.
MobileMe & dot Mac will still work last I heard.
iCloud Mail setup, even in 10.4/10.5…
Don't delete your old account yet. Just setup a new one in Mail>Preferences>Accounts, little plus icon. Choose IMAP as account type, not ,mac or MobileMe.
IMAP (Incoming Mail Server) information:
          ▪          Server name: imap.mail.me.com
          ▪          SSL Required: Yes
          ▪          Port: 993
          ▪          Username: [email protected] (use your @me.com address from your iCloud account)
          ▪          Password: Your iCloud password
SMTP (outgoing mail server) information:
          ▪          Server name: smtp.mail.me.com
          ▪          SSL Required: Yes
          ▪          Port: 587
          ▪          SMTP Authentication Required: Yes
          ▪          Username: [email protected] (use your @me.com address from your iCloud account)
          ▪          Password: Your iCloud password

Iphone 5 problem with in & out going call with iOS 8.1

I have a iphone 5 and i had updated it to ios8.1 recently.
After doing so, i started having problem in both in and out going calls. It work only for a brief period after i restart the phone but after a while it gives me the same trouble.
I already tried to reset the phone to factory settings, but it still doesnt effect.
Please help me to get rid of this problem..
Warm Regards
Smaran

Hello there, Smaran89.
Great job troubleshooting on your own to resolve your issue. The following Knowledge Base article offers up some great and thorough recommendations for troubleshooting issues with making or receiving calls on your iPhone:
iPhone: Troubleshooting issues making or receiving calls - Apple Support
Follow the steps below to resolve this issue. Please test after each step.
Toggle airplane mode: Tap Settings > Enable Airplane Mode, wait five seconds, then turn off airplane mode.
Check your phone settings:
Check your Do Not Disturb settings: Tap Settings > Do Not Disturb.
Check for any blocked phone numbers: Tap Settings > Phone > Blocked.
See if Call Forwarding is turned on: Tap Settings > Phone > Call Forwarding.
Ensure that your software is up to date:
Check for a carrier settings update.
Check for an iOS software update.
Note: Some updates may require a Wi-Fi connection.
If the iPhone has a SIM card, reseat the SIM card.
If the iPhone 4 or iPhone 4s is on the Verizon network, dial *228 from the iPhone and select option 2 to update the Preferred Roaming List (PRL). The PRL determines the cellular towers the phone uses for cellular service, selecting those with the best signal strength.
Reset the network settings: Tap Settings > General > Reset > Reset Network Settings.
Try to make or receive calls in another location.
Attempt to isolate to one network band:
If you're having the issue on LTE, disable LTE, if possible, and try again.
If you're having the issue on 3G/4G, disable 3G/4G, if possible, and try again.
Contact the carrier to check the following:
Your account is properly configured to use the specific iPhone that has the issue.
There are no localized service outages.
Your account doesn't have a billing-related block.
Your calls don't have errors on the carrier system.
Restore the phone as new.
If the above steps don't resolve the issue, go to an Apple Retail Store, carrier, Apple Authorized Reseller, or contact AppleCare to send the phone in for service.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

My payslip gets emailed to me and opens with fire fox , i can not print it out have tried saving to doc but still opens will not print

my payslip gets emailed to me and opens with firefox , i can not print it out have tried saving to doc, but still opens with firefox and will not print.
The server i have to use for my pay is Explorer( i told them that this would have conflicting things on my computer, they said no i wont.( i can get it just can not print it?)

Hi there morinallen,
Try downloading and running the print and scan doctor located here to ensure there are no software conflicts:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
It can fix a lot on its own and if not give a better idea of what is going on.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Out going call problem

i have iphone 5
i am not able to make out going call
i restore twice but no use
other functions is working properly like incoming etc

Hi kittupatsa,
If you are having issues making calls on your iPhone, you may find the following article helpful:
iPhone: Troubleshooting issues making or receiving calls
https://support.apple.com/kb/TS3406
Regards,
- Brenden

Since I downloaded iOS6.1 I can not hear my messages/phone calls/emails or any sounds when the phone is lock. Any setting I can change?

Since I downloaded iOS6.1 I can not hear my messages/phone calls/emails or any sounds when the phone is lock. It doesnt connect to bluetooth either. Any setting I have to change?
My sounds settings are ON and my side mute button is NOT pushed down to orange.
When the phone is unlock all the sounds are fine, but as soon as it locks it goes dead silent mode!

http://support.apple.com/kb/TS1630

I am trying to get space on an external hard drive which has some old time machine back up files that I do not need but can not eliminate, even by going into the time machine, clicking on the backup file to be eliminated and using the drop down eliminate

I am trying to get space on an external hard drive which has some old time machine back up files that I do not need but can not eliminate, even by going into the time machine, clicking on the backup file to be eliminated and using the drop down menu with the gear box symbol to eliminate

I cannot find this 300GB "Backup" in the Finder, only in the Storage info when I check "About This Mac".
You are probably using Time Machine to backup your MacBook Pro, right? Then the additional 300 GB could be local Time Machine snapshots. Time Machine will write the hourly backups to the free space on your hard disk, if the backup drive is temporarily not connected. You do not see these local backups in the Finder, and MacOS will delete them, when you make a regular backup to Time Machine, or when you need the space for other data.
See Pondini's page for more explanation: What are Local Snapshots? http://pondini.org/TM/FAQ.html
I have restarted my computer, but the information remains the same. How do I reclaim the use of the 300GB? Why is it showing up as "Backups" when it used to indicate "Photos"? Are my photos safe on the external drive?
You have tested the library on the external drive, and so your photos are save there.
The local TimeMachine snapshot probably now contains a backup of the moved library. Try, if connecting your Time Machine drive will reduce the size of your local Time Machine snapshots.

HT1454 why i can not get video out from my ipod touch after i did the upgrade

why i can not get video out from my ipod touch after i did the upgrade

why i can not get video out from my ipod touch after i did the upgrade

HT1454 Can not get video out from my ipod touch 3rd gen. Any ideas? It should nt be diffiicult to do this on the 21 st century, or not?

After having spent EUR 130 on cables from apple, i still can not get video out from my ipod touch 3rd gen. Any ideas? It should nt be diffiicult to do this on the 21 st century, or not?

Backing up an iOS device will copy some data to a backup file within iTunes, but this excludes all media. You can also transfer iTunes Store purchases from the iDevice to iTunes but, without using a third-party tool, nothing else. As long as you do not sync the iPod with your new library, the media that's on it will remain ... for as long as it keeps functioning, is not lost, stolen, eaten by the dog, ...
You may also have an option to recover your previous library from your old laptop; as long as its hard drive isn't fried, a computer repair store or technician may be able to extract the drive, mount it in an external enclosure, and copy your data to another PC. Whatever you choose, there is no real alternative to having all your media on your computer, managed by iTunes, and regularly backed up to another device/location.

System is not picking bank out going account in TBB1

Hi All,
I am facing the problem in TBB1 accounting entries, system is picking the bank main account (From House bank/account id assigned GL) Not picking Bank out going account from account determination
Example:
Accounting entry at the time of TBB1: (Term start)
Wrong entry
Dr. Fixed Term Deposit GL account
Cr. Bank Main account (Which is assigned in House bank/account ID)
Correct accounting entry should be like this:
Dr. Fixed Term Deposit GL account
Cr. Bank out going account
I have checked the Payment configuration but still not able to identify the issue
Thank in advance for your help and support
Regards,
MS

Hi Ravi,
I was going through your reply.
I needed some clarity on my understanding please confirm it.
Suppose Bank Account is : 113150 ( Created in FS00)
Bank Clearing Account for Treasury Clearing purpose is 114150 (not yet created in FS00)
Bank Clearing for non treasury clearing purpose is 112150 (created in FS00)
in my account determination of TRM I have maintained masking as ++++++4+++
then in this case when posting happens Account picked up will be 114150 based on my House Bank detail in payment tab.
Although 114150 is not created in FS00 and not maintained in T042Y in FBZP. and system will throw error.
Am I right?
Please confirm the understanding.

Why did you changed the big screen picture it look so better that way PLSS !!! Put it back so small I can not even see who's calling me

Why did you changed the big screen picture it look so better that way PLSS !!! Put it back so small I can not even see who's calling me

Send feedback below:
http://www.apple.com/feedback/iphone.html

CME - can not dail PSTN (out going calls )

Similar Messages

Maybe you are looking for