CME/CUE SIP Phones DTMF-Relay

Hi all,
Just looking for some clarification on this one.  I'm seeing some conflicting advice about setting the DTMF-Relay on SIP Phones registered to CME with a CUE Module.  I've read some documentation indicating that rtp-nte RFC2833 is the only dtmf-relay supported for SIP Phones registered to CME, however I've also read some documents indicating that sip-notify must be configured as the dtmf-relay on SIP phones when they are communicating to a CUE module.  I'm assuming I'm going to need to configure an MTP on the CME, but just wondering what the official DTMF config should be under the voice register pool for SIP phones.
Thanks!

Hi  logan
When doing lab with cme 7.0 and sip phones .sip phones are  not recognizing the "sip-notify" dtmf-relay method .It can only recognize "rtp-nte" method and it does not matter weather you are using sip-notify or rtp-nte for a dial-peer pointing to cme .
i configured on cue
ccn subsystem sip
dtmf-relay sip-notify
end
on cme i configured a dial-peer pointing to cue
dial-peer v 3888 voip
destination-pattern 3888
session target ipv4:177.3.11.10
codec g711ulaw
no vad
session protocol sipv2
dtmf-relay sip-notiy
on my sip phones
voice register pool 1
dtmf-relay sip-notify  ------> now in this case cue wont recognize dtmf tones
                                    when i change this dtmf-relay method to rtp-nte it recognizes dtmf tones to  when recording  a message

Similar Messages

  • SIP phone DTMF issue registered on a CUCME H323 gateway

    I have a CUCME 10 gateway that is registered on a  callmanager as H.323 gateway.
    On this a Cisco 8831 SIP conference bridge that is not generating DTMF. No sound heard in the other end when pressing digits, its just muting the sound. Anyone got a tip?     
    Callflow is  8831->CME->CM->PSTN
    voice register pool  1
     busy-trigger-per-button 1
     id mac xxx.xxxx.xxxx
     type 8831
     number 1 dn 1
     dtmf-relay sip-kpml
    dial-peer voice 1201 voip
     destination-pattern ...T
     progress_ind setup enable 3
     delay transport-address
     session target ipv4: callmanager ip address
     incoming called-number .
     voice-class codec 100  
     dtmf-relay rtp-nte  <- Also tried dtmf-relay h245-alphanumeric

    Can you try this..
    On your voice register pool configure
     dtmf-relay rtp-nte digit drop
    And on your dial peer 1201
    Dtmf-relay h245-alpha

  • Dtmf-relay sip-notify

    Evening Cisco techs,
    Having trouble enabling sip-notify
    Using CME 3.3 via (C2691-IPVOICEK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
    Have registered cisco phones set up in CME
    SIP is enabled on router. So is H323
    In conf t mode via voice service voip
    Upon using dtmf-relay sip-notify I get the error of unrecognised command
    If other information is required. Please let me know

    Just go to your SIP dial-peers:
    R01#conf t
    R01#dial-peer voice XX voip    << XX is you SIP dial-peer
    R01(config-dial-peer)#dtmf-relay ?
      cisco-rtp          Cisco Proprietary RTP
      h245-alphanumeric  DTMF Relay via H245 Alphanumeric IE
      h245-signal        DTMF Relay via H245 Signal IE
      rtp-nte            RTP Named Telephone Event RFC 2833
      sip-kpml           DTMF Relay via KPML over SIP SUBCRIBE/NOTIFY
      sip-notify         DTMF Relay via SIP NOTIFY messages
    dial-peer voice 555 voip
     destination-pattern 55555
     session protocol sipv2
     session target ipv4:1.1.1.1
     dtmf-relay sip-notify
    -Terry

  • DTMF relay

    Hello,
    I have problem relaying DTMF signals from MCU to H.320 GW.
    I was trying to invite an IVR number via H.320 GW. I was able to call the IVR number. Then the IVR asks for extension number. I provided the number. However, this information was not relayed by the MCU.
    Thanks

    Just go to your SIP dial-peers:
    R01#conf t
    R01#dial-peer voice XX voip    << XX is you SIP dial-peer
    R01(config-dial-peer)#dtmf-relay ?
      cisco-rtp          Cisco Proprietary RTP
      h245-alphanumeric  DTMF Relay via H245 Alphanumeric IE
      h245-signal        DTMF Relay via H245 Signal IE
      rtp-nte            RTP Named Telephone Event RFC 2833
      sip-kpml           DTMF Relay via KPML over SIP SUBCRIBE/NOTIFY
      sip-notify         DTMF Relay via SIP NOTIFY messages
    dial-peer voice 555 voip
     destination-pattern 55555
     session protocol sipv2
     session target ipv4:1.1.1.1
     dtmf-relay sip-notify
    -Terry

  • Cisco SIP Phone 9971 won't register on CME 8.6 or 8.5 Please HELP

    Please help me , I have problem with registering Cisco SIP phone 9971 with CME 8.6 on ISR 2901.
    I configured CME for SIP clients, then I add configuration for 9971 phone and create profiles.  Phone downloaded SEP...xml file from CME,after that phone look for g4-tones.xml and gd-sip.jar files, I added them to CME after that phone downloaded them and reboot. Now phone is stuck in some kind of loop and does not register on CME.
    On phone log I can see repeting next few messeges.
    12:01:58a No DNS Server IP
    12:01:59a Updating Trust list
    12:01:59a No Trust List instaled
    12:01:59a SEP04C5AB03B0D.cnf.xml (TFTP)  // at this time phone download SEP...xml file from CME
    12:02:00a VPN Error: VPN is not Configured
    on CME if issue DEBUG TFTP EVENTS i receive next few lines
    *Aug 18 18:20:19.891: TFTP: Looking for CTLSEP04C5A4B03B0D.tlv
    *Aug 18 18:20:19.987: TFTP: Looking for ITLSEP04C5A4B03B0D.tlv
    *Aug 18 18:20:20.083: TFTP: Looking for ITLFile.tlv
    *Aug 18 18:20:20.347: TFTP: Looking for SEP04C5A4B03B0D.cnf.xml
    *Aug 18 18:20:20.351: TFTP: Opened flash:/SEP04C5A4B03B0D.cnf.xml, fd 14, size 4585 for process 141
    *Aug 18 18:20:20.363: TFTP: Finished flash:/SEP04C5A4B03B0D.cnf.xml, time 00:00:00 for process 141
    here you can see verison info of CME
    Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Thu 24-Mar-11 15:31 by prod_rel_team
    ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
    ELTOSAN_ROUTER uptime is 1 hour, 50 minutes
    System returned to ROM by reload at 16:29:20 UTC Thu Aug 18 2011
    System image file is "flash:/c2900-universalk9-mz.SPA.151-4.M.bin"
    Last reload type: Normal Reload
    Last reload reason: Reload Command
    Cisco CISCO2901/K9 (revision 1.0) with 471040K/53248K bytes of memory.
    Processor board ID FGL1508252Y
    3 Gigabit Ethernet interfaces
    2 terminal lines
    1 Virtual Private Network (VPN) Module
    4 Voice FXO interfaces
    4 Voice FXS interfaces
    1 Internal Services Module (ISM) with Services Ready Engine (SRE)
       Survivable Remote Site Voicemail (SRSV) on Cisco Unity Express (CUE) 8.5.1 in slot/sub-slot 0/0
    DRAM configuration is 64 bits wide with parity enabled.
    255K bytes of non-volatile configuration memory.
    254464K bytes of ATA System CompactFlash 0 (Read/Write)
    License Info:
    License UDI:
    Device#   PID                   SN
    *0        CISCO2901/K9          xxxxxxxxxxxxx
    Technology Package License Information for Module:'c2900'
    Technology    Technology-package          Technology-package
                  Current       Type          Next reboot
    ipbase        ipbasek9      Permanent     ipbasek9
    security      securityk9    Permanent     securityk9
    uc            uck9          Permanent     uck9
    data          None          None          None
    Configuration register is 0x2102
    this is RUNNING CONFIGURATION
    ! Last configuration change at 16:10:12 UTC Thu Aug 18 2011
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname ELTOSAN_ROUTER
    boot-start-marker
    boot system flash:/c2900-universalk9-mz.SPA.151-4.M.bin
    boot-end-marker
    no aaa new-model
    no ipv6 cef
    ip source-route
    no ip routing
    no ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 192.168.5.1 192.168.5.10
    ip dhcp excluded-address 192.168.5.200 192.168.5.255
    ip dhcp pool phone
       network 192.168.5.0 255.255.255.0
       default-router 192.168.5.251
       option 150 ip 192.168.5.251
    ip dhcp pool data
       relay source 192.168.2.0 255.255.255.0
       relay destination 192.168.2.201
    multilink bundle-name authenticated
    crypto pki token default removal timeout 0
    voice-card 0
    voice service voip
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    fax protocol pass-through g711alaw
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 192.168.5.251 port 5060
    max-dn 6
    max-pool 6
    load 9971 sip9971.9-1-1SR1.loads
    authenticate register
    tftp-path flash:
    create profile sync 0005135312289902
    voice register dn  1
    number 207
    allow watch
    name GossaVM
    label 207
    voice register dn  3
    number 101
    name Dejan
    label 101
    mwi
    voice register pool  1
    id mac 000C.29C5.0011
    number 1 dn 1
    dtmf-relay sip-notify
    username testvm password testera
    codec g711alaw
    voice register pool  3
    id mac 04C5.A4B0.3B0D
    type 9971
    number 3 dn 3
    presence call-list
    dtmf-relay rtp-nte
    username dejan password 1234
    codec g711alaw
    no vad
    license udi pid CISCO2901/K9 sn xxxxxxxxxxxx
    hw-module ism 0
    hw-module pvdm 0/0
    redundancy
    interface GigabitEthernet0/0
    description INTERFACE INTERNAL
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    no mop enabled
    interface GigabitEthernet0/0.2
    description LAN DATA
    encapsulation dot1Q 2
    ip address 192.168.2.251 255.255.255.0
    no ip route-cache
    interface GigabitEthernet0/0.5
    description LAN VOICE
    encapsulation dot1Q 5
    ip address 192.168.5.251 255.255.255.0
    no ip route-cache
    interface ISM0/0
    no ip address
    no ip route-cache
    shutdown
    !Application: SRSV-CUE Running on ISM
    interface GigabitEthernet0/1
    no ip address
    no ip route-cache
    shutdown
    duplex auto
    speed auto
    interface ISM0/1
    description Internal switch interface connected to Internal Service Module
    shutdown
    interface Vlan1
    no ip address
    no ip route-cache
    shutdown
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    snmp-server community public RO
    tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
    tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
    tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
    tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
    tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
    tftp-server flash:sip9971.9-1-1SR1.loads alias sip9971.9-1-1SR1.loads
    tftp-server flash:United_States/g4-tones.xml
    tftp-server flash:English_United_States/gd-sip.jar
    control-plane
    voice-port 0/0/0
    voice-port 0/0/1
    voice-port 0/0/2
    voice-port 0/0/3
    voice-port 0/1/0
    voice-port 0/1/1
    voice-port 0/1/2
    voice-port 0/1/3
    mgcp profile default
    gatekeeper
    shutdown
    line con 0
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    line vty 0 4
    password jebiga
    login
    transport input all
    end
    I did not have any kind of problem with X-LITE to register to CME. also try with few SCCP phones 7940  and I did not any kind of problem .
    this is content of SEP....xml file for 9971
    <device>
    <deviceProtocol>SIP</deviceProtocol>
    <devicePool>
    <dateTimeSetting>
    <dateTemplate>M/D/YA</dateTemplate>
    <timeZone>Pacific Standard/Daylight Time</timeZone>
    <ntps>
    <ntp priority="0">
    <name>0.0.0.0</name>
    <ntpMode>unicast</ntpMode>
    </ntp>
    </ntps>
    </dateTimeSetting>
    <callManagerGroup>
    <members>
    <member priority="0">
    <callManager>
    <ports>
    <sipPort>5060</sipPort>
    </ports>
    <processNodeName>192.168.5.251</processNodeName>
    </callManager>
    </member>
    </members>
    </callManagerGroup>
    </devicePool>
    <sipProfile>
    <sipProxies>
    <registerWithProxy>true</registerWithProxy>
    </sipProxies>
    <sipCallFeatures>
    <cnfJoinEnabled>true</cnfJoinEnabled>
    <localCfwdEnable>true</localCfwdEnable>
    <callForwardURI>service-uri-cfwdall</callForwardURI>
    <callPickupURI>service-uri-pickup</callPickupURI>
    <callPickupGroupURI>service-uri-gpickup</callPickupGroupURI>
    <callHoldRingback>2</callHoldRingback>
    <semiAttendedTransfer>true</semiAttendedTransfer>
    <anonymousCallBlock>2</anonymousCallBlock>
    <callerIdBlocking>2</callerIdBlocking>
    <dndControl>2</dndControl>
    <remoteCcEnable>true</remoteCcEnable>
    </sipCallFeatures>
    <sipStack>
    <remotePartyID>true</remotePartyID>
    </sipStack>
    <sipLines>
    <line button="1" lineIndex="1">
    <featureID>9</featureID>
    <featureLabel></featureLabel>
    <proxy>USECALLMANAGER</proxy>
    <port>5060</port>
    <name></name>
    <displayName></displayName>
    <autoAnswer>
    <autoAnswerEnabled>2</autoAnswerEnabled>
    </autoAnswer>
    <callWaiting>1</callWaiting>
    <authName>dejan</authName>
    <authPassword>1234</authPassword>
    <sharedLine>false</sharedLine>
    <messagesNumber></messagesNumber>
    <ringSettingActive>5</ringSettingActive>
    <forwardCallInfoDisplay>
    <callerName>true</callerName>
    <callerNumber>true</callerNumber>
    <redirectedNumber>true</redirectedNumber>
    <dialedNumber>true</dialedNumber>
    </forwardCallInfoDisplay>
    </line>
    <line button="2" lineIndex="2">
    <featureID>9</featureID>
    <featureLabel>101</featureLabel>
    <proxy>USECALLMANAGER</proxy>
    <port>5060</port>
    <name>101</name>
    <displayName>Dejan Rakic</displayName>
    <autoAnswer>
    <autoAnswerEnabled>2</autoAnswerEnabled>
    </autoAnswer>
    <callWaiting>1</callWaiting>
    <authName>dejan</authName>
    <authPassword>1234</authPassword>
    <sharedLine>false</sharedLine>
    <messagesNumber></messagesNumber>
    <ringSettingActive>5</ringSettingActive>
    <forwardCallInfoDisplay>
    <callerName>true</callerName>
    <callerNumber>true</callerNumber>
    <redirectedNumber>true</redirectedNumber>
    <dialedNumber>true</dialedNumber>
    </forwardCallInfoDisplay>
    </line>
    </sipLines>
    <enableVad>true</enableVad>
    <preferredCodec>g711alaw</preferredCodec>
    <dialTemplate></dialTemplate>
    <kpml>1</kpml>
    <phoneLabel></phoneLabel>
    <stutterMsgWaiting>2</stutterMsgWaiting>
    <disableLocalSpeedDialConfig>true</disableLocalSpeedDialConfig>
    <dscpForAudio>184</dscpForAudio>
    <dscpVideo>136</dscpVideo>
    </sipProfile>
    <commonProfile>
    <phonePassword>1234</phonePassword>
    <callLogBlfEnabled>2</callLogBlfEnabled>
    </commonProfile>
    <featurePolicyFile>featurePolicyDefault.xml</featurePolicyFile>
    <loadInformation>sip9971.9-1-1SR1.loads</loadInformation>
    <vendorConfig>
    </vendorConfig>
    <commonConfig>
    <videoCapability>0</videoCapability>
    <ciscoCamera>0</ciscoCamera>
    </commonConfig>
    <sshUserId>dejan</sshUserId>
    <sshPassword>1234</sshPassword>
    <userId></userId>
    <phoneServices>
    <provisioning>2</provisioning>
    <phoneService  type="1" category="0">
    <name>Missed Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/MissedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="1" category="0">
    <name>Received Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/ReceivedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="1" category="0">
    <name>Placed Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/PlacedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="2" category="0">
    <name>Voicemail</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/Voicemail</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    </phoneServices>
    <versionStamp>0131511014412102</versionStamp>
    <userLocale>
    <name>English_United_States</name>
    <langCode>en</langCode>
    </userLocale>
    <networkLocale>United_States</networkLocale>
    <networkLocaleInfo>
    <name>United_States</name>
    </networkLocaleInfo>
    <authenticationURL></authenticationURL>
    <directoryURL></directoryURL>
    <servicesURL>http://192.168.5.251:80/CMEserverForPhone/serviceurl</servicesURL>
    <dscpForSCCPPhoneServices>0</dscpForSCCPPhoneServices>
    <dscpForCm2Dvce>96</dscpForCm2Dvce>
    <transportLayerProtocol>2</transportLayerProtocol>
    </device>

    Hello,
    I'm facing exactly the same problem, that is:
    a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
    I have read all the postings to this Forum, but I have not been able to solve it.
    In my case the commands voice register dn  and  voice register pool are OK.
    So frankly, I have no idea what I could be missing.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

  • CUE 8.6.7 - Can't sync users from SIP phones

    Hello, I'm trying to Synchronize information from CUCME version 10.0 to create new users and assign a mailbox, I don't have any problems with phones using SCCP, but I can't see phones running SIP, is there any configuration that I'm missing??
    voice register global
     mode  cme
     source-address 172.16.10.129 port 5060
     timeouts interdigit 5
     max-dn 200
     max-pool 42
     load 3905 CP3905.9-2-1-0
     authenticate register
     timezone 9
     time-format 24
     date-format D/M/Y
     hold-alert
     no dst auto-adjust
     voicemail 290
     create profile sync 0005396071474939
     network-locale ES
     user-locale ES
     ntp-server 172.16.10.129 mode directedbroadcast
     conference hardware
    voice register dn  1
     number 253
     name User1
     huntstop channel 3
    voice register pool  1
     busy-trigger-per-button 2
     id mac F41F.C267.ECC7
     type 3905
     number 1 dn 1
     template 1
     dtmf-relay sip-kpml
     username user1 password user1
     description user1
     codec g711ulaw
    Regards,
    Juan Carlos Arias

    Did you ever find an answer to your question?  Building CUCME with 7841 SIP only phones and trying to research if there is a resolution to SIP users not synchronizing in CUE.

  • Cisco CP-78XX SIP Phone Pickup Not Work on CME

    Hi,
    I configured some SIP phones (CP-7821, CP-7841) with pickup function. Is it the Pickup / GPickup soft keys not function as the SIP phone? If yes, then I can use the FAC to access that? And I tried the FAC std. / custom as the pickup / gpickup  .. both not work ... I don't know how to use the FAC on CME? As the FAC std., if I pickup local, that I should press (**3) > call?
    Ref.:
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmecover.html#45535
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmefacs.html#30064
    This is the configuration:
    CME-SIP-Phone#sh run
    Building configuration...
    Current configuration : 5413 bytes
    ! Last configuration change at 11:06:12 UTC Fri Nov 28 2014 by mtlops
    version 15.4
    no service pad
    service tcp-keepalives-in
    service tcp-keepalives-out
    service timestamps debug datetime msec localtime show-timezone
    service timestamps log datetime msec localtime show-timezone
    service password-encryption
    service sequence-numbers
    hostname CME-SIP-Phone
    boot-start-marker
    boot system flash:c2900-universalk9-mz.SPA.154-2.T1.bin
    boot-end-marker
    ! card type command needed for slot/vwic-slot 0/0
    enable secret 5 $XXXXXXXXXXXXXXXXXXXXXXXX
    aaa new-model
    aaa authentication login default local
    aaa authorization console
    aaa authorization exec default local
    aaa session-id common
    ip cef
    no ipv6 cef
    multilink bundle-name authenticated
    stcapp feature access-code
    voice-card 0
     dspfarm
     dsp services dspfarm
    voice service pots
    voice service voip
     ip address trusted list
      ipv4 10.118.0.0 255.255.255.0
     allow-connections h323 to h323
     allow-connections h323 to sip
     allow-connections sip to h323
     allow-connections sip to sip
     supplementary-service h450.12
     no supplementary-service h225-notify cid-update
     redirect ip2ip
     fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
     h323
      no h225 timeout keepalive
      call preserve
     sip
      bind control source-interface GigabitEthernet0/0
      bind media source-interface GigabitEthernet0/0
      registrar server expires max 600 min 60
    voice class codec 1
     codec preference 1 g711ulaw
     codec preference 2 g711alaw
     codec preference 3 g729r8
    voice class h323 1
      h225 timeout tcp establish 3
      call preserve
    voice class custom-cptone ABC-Company
     dualtone disconnect
      frequency 425
      cadence 500 500
    voice register pool-type  7821
     description Cisco IP Phone 7821
     reference-pooltype 6921
    voice register pool-type  7841
     description Cisco IP Phone 7841
     reference-pooltype 6941
    voice register global
     mode  cme
     source-address 10.118.0.10 port 5060
     timeouts interdigit 2
     max-dn 200
     max-pool 100
     authenticate register
     authenticate realm all
     timezone 42
     time-format 24
     date-format D/M/Y
     mwi stutter
     mwi reg-e164
     voicemail 5000
     call-feature-uri pickup http://10.118.0.10/pickup
     call-feature-uri gpickup http://10.118.0.10/gpickup
     tftp-path flash:
     file text
     create profile sync 0001170446349417
     ntp-server 10.118.0.10 mode unicast
     ip qos dscp af11 media
     ip qos dscp cs2 signal
     ip qos dscp af43 video
     ip qos dscp 25 service
     camera
     video
    voice register dn  2
     number 1000
     pickup-call any-group
     pickup-group 1
     name BB Leung
     label BB Leung
    voice register dn  3
     number 1001
     pickup-call any-group
     pickup-group 1
     name CC Chan
     label CC Chan
    voice register dn  4
     number 1002
     pickup-call any-group
     pickup-group 1
     name DD Leung
     label DD Leung
    voice register dn  50
     mwi
    voice register template  1
     softkeys hold  Newcall Resume
     softkeys idle  Newcall Redial Gpickup Pickup Cfwdall DND
     softkeys seized  Cfwdall Endcall Redial
     softkeys connected  Confrn Endcall Hold Trnsfer
    voice register pool  1
     busy-trigger-per-button 1
     id mac A8XX.XXXX.XXXX
     type 7841
     number 1 dn 2
     template 1
     dtmf-relay sip-notify
     username 1001 password 112233
     codec g711ulaw
     no vad
    voice register pool  2
     busy-trigger-per-button 1
     id mac 50XX.XXXX.XXXX
     type 7841
     number 1 dn 3
     template 1
     dtmf-relay sip-notify
     username 1002 password 112233
     codec g711ulaw
     no vad
    voice register pool  3
     busy-trigger-per-button 1
     id mac 00XX.XXXX.XXXX
     type 7821
     number 1 dn 4
     template 1
     dtmf-relay sip-notify
     username 1003 password 112233
     codec g711ulaw
     no vad
    license udi pid CISCO2921/K9 sn FHK1407F25D
    license accept end user agreement
    license boot c2900 technology-package uck9
    hw-module pvdm 0/0
    hw-module sm 1
    username mtlops privilege 15 secret 5 $1$0qqx$1WGdfRW.flJrwmY7k8eUy0
    redundancy
    interface Embedded-Service-Engine0/0
     no ip address
     shutdown
    interface GigabitEthernet0/0
     ip address 10.118.0.10 255.255.255.0
     duplex auto
     speed auto
    interface GigabitEthernet0/1
     no ip address
     shutdown
     duplex auto
     speed auto
    interface GigabitEthernet0/2
     no ip address
     shutdown
     duplex auto
     speed auto
    interface SM1/0
     no ip address
     shutdown
     service-module fail-open
    interface SM1/1
     no ip address
    interface Vlan1
     no ip address
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    ip route 0.0.0.0 0.0.0.0 10.118.0.1
    control-plane
    mgcp behavior rsip-range tgcp-only
    mgcp behavior comedia-role none
    mgcp behavior comedia-check-media-src disable
    mgcp behavior comedia-sdp-force disable
    mgcp profile default
    dspfarm profile 1 conference
     codec g711ulaw
     codec g711alaw
     codec g729ar8
     codec g729abr8
     codec g729r8
     codec g729br8
     maximum sessions 7
     associate application SCCP
     shutdown
    gatekeeper
     shutdown
    telephony-service
     max-conferences 8 gain -6
     transfer-system full-consult
     fac standard
    line con 0
    line aux 0
    line 2
     no activation-character
     no exec
     transport preferred none
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
     stopbits 1
    line 67
     no activation-character
     no exec
     transport preferred none
     transport input all
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
     stopbits 1
    line vty 0 4
     transport input all
    scheduler allocate 20000 1000
    end
    CME-SIP-Phone#sh telephony-service fac
      telephony-service fac standard
        callfwd all **1
        callfwd cancel **2
        pickup local **3
        pickup group **4
        pickup direct **5
        park **6
        dnd **7
        redial **8
        voicemail **9
        ephone-hunt join *3
        ephone-hunt cancel #3
        ephone-hunt hlog *4
        ephone-hunt hlog-phone *5
        trnsfvm *6
        dpark-retrieval *0
        cancel call waiting *1

    VPN is not Configured prints on all phones now with the built-in VPN client if VPN isn't configured.  That's normal and is just cosmetic.  That should not be causing your registration issues.

  • Cisco SIP Phone 9971 won't register on CME 8.6

    Hello,
    I'm facing a very strange problem:
    a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
    I have read all the related-postings to this and other Forum, but I have not been able to solve it.
    One of the "potential solutions" was to make sure that the Phone had a Line configured.
    But I think that the commands voice register dn  and  voice register pool are properly configured (see config below)
    So frankly, I have no idea what I could be missing.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

    Thank you for your reply.
    I did some debugs and the results are very strange!
    This is what I got:
    Feb 24 18:01:12.219: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Sent:
    SIP/2.0 400 Bad Request
    Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK08011844
    From: ;tag=189c5db6bd09000260cf3daf-289a76d1
    To: ;tag=52488-160A
    Date: Mon, 24 Feb 2014 18:01:12 GMT
    Call-ID: [email protected]
    CSeq: 1000 REFER
    Content-Length: 0
    Contact:
    Feb 24 18:01:12.291: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    REGISTER sip:172.25.140.1 SIP/2.0
    Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK1e9ad079
    From: ;tag=189c5db6bd0900032df02e9c-25d79707
    To:
    Call-ID: [email protected]
    Max-Forwards: 70
    Date: Fri, 01 Jan 1982 00:02:41 GMT
    CSeq: 101 REGISTER
    User-Agent: Cisco-CP9971/9.4.1
    Contact: ;+sip.instance="
    000000-0000-0000-0000-189c5db6bd09>";+u.sip!devicename.ccm.cisco.com="SEP189C5DB
    6BD09";+u.sip!model.ccm.cisco.com="493";video
    Supported: replaces,join,sdp-anat,norefersub,resource-priority,extended-refer,X-
    cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-
    cisco-srtp-fallback,X-cisco-monrec,X-cisco-config,X-cisco-sis-6.0.2,X-cisco-xsi-
    8.0.1
    Content-Length: 0
    Reason: SIP;cause=200;text="cisco-alarm:22 Name=SEP189C5DB6BD09 ActiveLoad=sip99
    71.9-4-1-9.loads InactiveLoad=sip9971.9-3-2SR1-1.loads Last=reset-reset"
    Expires: 3600
    Feb 24 18:01:12.395: voice_reg_get_reg_expires_timer: no voice register pool found
    Feb 24 18:01:12.395: VOICE_REG_POOL: Register request for (1010) from (172.35.140.12)
    Feb 24 18:01:12.395: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
    Feb 24 18:01:12.395: VOICE_REG_POOL: key(1010) contact(172.35.140.12:5060) add to contact table
    Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (1010) found in contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(1010) contact(172.35.140.12) added to contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) add to srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) added to srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    But right after these errors, I get the following:
    Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
    1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    VOICE_REG_POOL pool_tag(1), dn_tag(1)
    Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
    Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
    Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
                                   Name:SEP189C5DB6BD09 IP:172.35.140.12  DeviceType:Phone
    Feb 24 18:01:12.411: VOICE_REG_POOL: Pool[1]: service-control (reset type: 2) message sent to sip:[email protected]
    Feb 24 18:01:12.411: voice_reg_privacy_update_to_phone: delay sending privacy update during bulk registration
    Feb 24 18:01:12.415: //1/7B0070C28003/SIP/Msg/ccsipDisplayMsg:
    ====================
    And when I do a sh voice register pool, I get the following:
    C2811#sh voice register pool  1
    Pool Tag 1
    Config:
      Mac address is 189C.5DB6.BD09
      Type is 9971
      Number list 1 : DN 1
      Proxy Ip address is 0.0.0.0
      Current Phone load version is Cisco-CP9971/9.4.1
      DTMF Relay is enabled, rtp-nte
      Call Waiting is enabled
      DnD is disabled
      Video is enabled
      Camera is enabled
      Busy trigger per button value is 0
      call-forward b2bua busy 68600
      keep-conference is enabled
      registration expires timer max is 3600 and min is 120
      username adm password adm
      kpml signal is enabled
      Lpcor Type is none
      blf call list is enabled
      Transport type is udp
      service-control mechanism is supported
      registration Call ID is [email protected]
      Registration method: per line
      Privacy feature is not configured.
      Privacy button is disabled
      active primary line is: 1010
      contact IP address: 172.35.140.12 port 5060
      Phone SIS Version:  6.0.2
      GW SIS Version:  1.0.0
    Dialpeers created:
    Dial-peers for Pool 1:
    dial-peer voice 40001 voip
    destination-pattern 1010
    session target ipv4:172.35.140.12:5060
    session protocol sipv2
    dtmf-relay rtp-nte
    digit collect kpml
    codec  g711ulaw bytes 160
    no vad
      call-fwd-busy        68600
      after-hours-exempt   FALSE
    Statistics:
      Active registrations  : 4
      Total SIP phones registered: 1
      Total Registration Statistics
        Registration requests  : 4
        Registration success   : 4
        Registration failed    : 0
        unRegister requests    : 0
        unRegister success     : 0
        unRegister failed      : 0
        Attempts to register
               after last unregister : 0
        Last register request time   : 18:11:43.551 UTC Mon Feb 24 2014
        Last unregister request time :
        Register success time        : 18:11:43.551 UTC Mon Feb 24 2014
        Unregister success time      :
    C2811#
    So apparently the Phone is actually registered!
    However, the Phone screens still shows this message: Phone Not Registered.
    So frankly I don't understand what's going on!
    I really hope somebody can help.  Thanks!

  • Cisco SIP Phone 9971 will not register on CME 8.6

    Hello,
    I'm trying to configure a  Cisco SIP Phone 9971,
    but it won't register on CME 8.6, which is running on a 2811
    The Phone shows this error message: Phone Not Registered.
    And when I check the the Status Messages in the Phone, I see the following:
    VPN Error: vpn is not configured
    Actually, it shows all these 4 messages in a constant Loop:
    12:01:59a SEP189C5DB6BD09.cnf.xml (TFTP)
    12:01:59a No Trust List instaled
    12:01:59a Updating Trust list
    12:02:00a VPN Error: VPN is not Configured
    It seems that this VPN Error is keeping the Phone from registering.
    This is repeated for ever and the Phone never registers; at least that's what it appears.
    However, when I do a sh voice register pool, I get the following:
    C2811#sh voice register pool  1
    Pool Tag 1
    Config:
      Mac address is 189C.5DB6.BD09
      Type is 9971
      Number list 1 : DN 1
      Proxy Ip address is 0.0.0.0
      Current Phone load version is Cisco-CP9971/9.4.1
      DTMF Relay is enabled, rtp-nte
      Call Waiting is enabled
      DnD is disabled
      Video is enabled
      Camera is enabled
      Busy trigger per button value is 0
      call-forward b2bua busy 68600
      keep-conference is enabled
      registration expires timer max is 3600 and min is 120
      username adm password adm
      kpml signal is enabled
      Lpcor Type is none
      blf call list is enabled
      Transport type is udp
      service-control mechanism is supported
      registration Call ID is [email protected]
      Registration method: per line
      Privacy feature is not configured.
      Privacy button is disabled
      active primary line is: 1010
      contact IP address: 172.35.140.12 port 5060
      Phone SIS Version:  6.0.2
      GW SIS Version:  1.0.0
    Dialpeers created:
    Dial-peers for Pool 1:
    dial-peer voice 40001 voip
    destination-pattern 1010
    session target ipv4:172.35.140.12:5060
    session protocol sipv2
    dtmf-relay rtp-nte
    digit collect kpml
    codec  g711ulaw bytes 160
    no vad
      call-fwd-busy        68600
      after-hours-exempt   FALSE
    Statistics:
      Active registrations  : 4
      Total SIP phones registered: 1
      Total Registration Statistics
        Registration requests  : 4
        Registration success   : 4
        Registration failed    : 0
        unRegister requests    : 0
        unRegister success     : 0
        unRegister failed      : 0
        Attempts to register
               after last unregister : 0
        Last register request time   : 18:11:43.551 UTC Mon Feb 24 2014
        Last unregister request time :
        Register success time        : 18:11:43.551 UTC Mon Feb 24 2014
        Unregister success time      :
    C2811#
    This sh voice register pool  seems to indicate that the Phone has actually registered.
    But I still get the  Phone Not Registered   message on the screen!
    I did some Debugs and they also seem to indicate that the Phone has indeed registered:
    Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
    1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    VOICE_REG_POOL pool_tag(1), dn_tag(1)
    Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
    Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
    Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
                                   Name:SEP189C5DB6BD09 IP:172.35.140.12  DeviceType:Phone
    So frankly, I have no idea why the Phone keeps showing the Phone Not Registered message.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

    VPN is not Configured prints on all phones now with the built-in VPN client if VPN isn't configured.  That's normal and is just cosmetic.  That should not be causing your registration issues.

  • CME SIP phone outside call issue

    Dear all,
    i have cme version 9.1 on router 2921 with 7962 sccp phones and 3905 sip phone.
    when i place outside call ( to pstn) using the below dial peer, call is processed. 
    when the call is answered by the autoattendent of the called company ( assume i called x company)  , i cant press any other numbers using the sip phones.
    i mean if i want to press zero for help or internal extension of the x company, these pressed numbered are not recognized by the analog panasonic PBX of the x company.
    Sccp phones works well.
    Any help please and below is the dial-peer.
    dial-peer voice 1003 pots
     trunkgroup 1
     corlist outgoing CITIES
     description CALLING CITIES
     destination-pattern 90[1-9]......
     forward-digits 8
    voice service voip
     allow-connections h323 to h323
     allow-connections h323 to sip
     allow-connections sip to h323
     allow-connections sip to sip
     no supplementary-service sip handle-replaces
     fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
     sip
      bind control source-interface GigabitEthernet0/2.10
      bind media source-interface GigabitEthernet0/2.10
      registrar server expires max 36000 min 600
    voice class codec 5
     codec preference 1 g729r8
     codec preference 2 g711ulaw
    voice register global
     mode cme
     source-address 10.100.4.20 port 5060
     max-dn 200
     max-pool 100
     load 3905 CP3905.9-2-1-0.loads
     authenticate register
     timezone 31
     date-format D/M/Y
     voicemail 177
     tftp-path flash:
     create profile sync 000473524028932A
     conference hardware
    voice register dn  1
     number 109
     allow watch
     pickup-call any-group
     pickup-group 170
     shared-line max-calls 3
    voice register pool  1
     id mac 6C99.8984.9678
     type 3905
     number 1 dn 1
     template 1
     dtmf-relay sip-notify
     voice-class codec 5
     username SFD1 password SFD1
    thanks

    Hi Yahsiel,
    firstly thanks for help, secondly if you don't mind i want to ask you the below if possible:
    1- in my cme, is there a way when i call an internal extension (e.g 110) from an internal phone it rings normally but when i call from outside-->autoattendent answers-->when i press 110 it get transferred to another phone (e.g 111)....????
    2- when i call from outside(pstn) to the cme -->when the plar command is directly to the internal extension the caller id appears but when the autoattendent answers and then transfer to the operator (by pressing zero) the caller id appears as unknown number ??????
    3- is the 3905 sip phone support 1Gbps when connected to the PC, as after connecting the phones to the PCs the speed decreased up to 100Mbps?? or it is another matter?
    (poe switches is cisco SG200)
    regards,

  • FAC LPCOR IS NOT WORKING IN CME SIP PHONES

    Dear Team,
    We are planning to put FAC on SIP (7821) phones for calling long distance.
    CME version is 10.0
    Please find the config
    gw-accounting aaa
    aaa new-model
    aaa authentication login h323 local
    aaa authorization exec h323 local 
    aaa authorization network h323 local 
    aaa session-id common
    voice register global
     mode  cme
     source-address 10.X.X.X port 5060
     timeouts interdigit 5
     max-dn 500
     max-pool 475
     load 7821 sip78xx.10-2-1-12
     authenticate register
     authenticate realm router.local
     timezone 35
     tftp-path flash:
     create profile sync 0003478159444525
    voice lpcor enable
    voice lpcor custom
     group 1 national-FAC
    voice lpcor policy national-FAC
     service fac
     accept national-FAC fac
    application
     package auth
      param max-retries 0
      param passwd-prompt flash0:/enter_pin.au
      param abort-digit *
      param user-prompt flash0:/enter_account.au
      param passwd 12345
      param term-digit #
      param max-digits 32
    username 1111 password 7 1446435A5D
    voice register pool  2
     lpcor type local
     lpcor incoming national-FAC
     lpcor outgoing national-FAC
     busy-trigger-per-button 1
     id mac F09E.636F.0F4B
     type 7821
     number 1 dn 2
     template 1
     cor incoming NATIONALACCESS 1 3002
     dtmf-relay rtp-nte sip-notify
     username user2 password cisco
     codec g711ulaw
    voice register dn  2
     number 3002
     call-forward b2bua noan 5000 timeout 20
     allow watch
     name 3002
     label 3002
    dial-peer voice 117 voip
     destination-pattern 905[0256].......$
     lpcor outgoing national-FAC
     session protocol sipv2
     session target ipv4:10.X.X.X
     incoming called-number .
     codec g711ulaw
     no vad
     label 3004
    CME#dir flash:
    Directory of flash0:/
        1  -rw-    96910452  Oct 21 2014 03:35:18 +04:00  c3900e-universalk9-mz.SPA.153-3.M3.bin
        2  -rw-        3064  Oct 21 2014 03:49:06 +04:00  cpconfig-39xx.cfg
        3  drw-           0  Nov 12 2014 14:09:54 +04:00  its
       14  drw-           0  Nov 12 2014 15:16:46 +04:00  GUI
       32  drw-           0  Oct 21 2014 03:49:32 +04:00  ccpexp
      273  -rw-        2464  Oct 21 2014 03:51:18 +04:00  home.shtml
      274  -rw-      116608  Nov 12 2014 15:10:32 +04:00  CME-GUI.rar
      275  -rw-     3090800  Nov 12 2014 16:35:04 +04:00  kern78xx.10-2-1-12.sbn
      276  -rw-    36307280  Nov 12 2014 16:36:00 +04:00  rootfs78xx.10-2-1-12.sbn
      277  -rw-      364072  Nov 12 2014 16:36:10 +04:00  sboot78xx.10-2-1-12.sbn
      278  -rw-        1228  Nov 12 2014 16:36:32 +04:00  sip78xx.10-2-1-12.loads
      279  -rw-      496521  Nov 12 2014 17:01:40 +04:00  music-on-hold.au
      280  -rw-       23660  Nov 19 2014 14:48:40 +04:00  enter_account.au
      281  -rw-       24164  Nov 19 2014 14:48:48 +04:00  enter_pin.au
    261324800 bytes total (120594432 bytes free)
    But when ever iam trying mobile calls call is disconnecting. please find the debugs
    Nov 19 20:04:34.661: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_peer:
       peer tag 40001, direction 0
    Nov 19 20:04:34.661: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_name:
       lpcor International-FAC
    Nov 19 20:04:34.661: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_name:
       lpcor International-FAC index 1
    Nov 19 20:04:34.661: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_peer:
       Return Lpcor Index 1 for Peer Tag 40001
    DAMAC_AKOYA-CME#
    Nov 19 20:04:39.225: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_name:
       lpcor International-FAC
    Nov 19 20:04:39.225: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_name:
       lpcor International-FAC index 1
    Nov 19 20:04:39.225: //-1/xxxxxxxxxxxx/LPCOR/lpcor_index_is_valid:
       lpcor index 1 is valid
    Nov 19 20:04:39.225: //-1/xxxxxxxxxxxx/LPCOR/lpcor_policy_validate_internal:
       Source LPCOR Index=1, Target LPCOR Policy=International-FAC
    Nov 19 20:04:39.225: -Traceback= 19E34D6z 581A4DCz 581AC7Fz 55B3588z 55B3063z 55AEA34z 55B6A53z 55B7255z 55B649Bz 55F5AF5z 5583EEFz 55894B6z 5589734z 55F5AF5z 558A44Az 55CF04Ez
    DAMAC_AKOYA-CME#
    Nov 19 20:04:39.225: //-1/xxxxxxxxxxxx/LPCOR/lpcor_policy_validate_internal:
       Validate Pass; lpcor (source[1] target[1])
    Nov 19 20:04:39.225: //-1/xxxxxxxxxxxx/LPCOR/lpcor_policy_validate_get_service:
       FAC is enabled; lpcor (source[1] target[1])
    Please advise. If iam missing any steps in this.
    Thanks,
    LAJAN JALEEL

    Dear Amit,
    The configuration is working fine. We find out what is the exact issue.
    *****Issue******
    Debug voice application auth was giving an out put that 
    user prompt url is not found , Even though the exact directory was there under flash0:
    CME#dir flash:
    Directory of flash0:/
        1  -rw-    96910452  Oct 21 2014 03:35:18 +04:00  c3900e-universalk9-mz.SPA.153-3.M3.bin
        2  -rw-        3064  Oct 21 2014 03:49:06 +04:00  cpconfig-39xx.cfg
        3  drw-           0  Nov 12 2014 14:09:54 +04:00  its
       14  drw-           0  Nov 12 2014 15:16:46 +04:00  GUI
       32  drw-           0  Oct 21 2014 03:49:32 +04:00  ccpexp
      273  -rw-        2464  Oct 21 2014 03:51:18 +04:00  home.shtml
      274  -rw-      116608  Nov 12 2014 15:10:32 +04:00  CME-GUI.rar
      275  -rw-     3090800  Nov 12 2014 16:35:04 +04:00  kern78xx.10-2-1-12.sbn
      276  -rw-    36307280  Nov 12 2014 16:36:00 +04:00  rootfs78xx.10-2-1-12.sbn
      277  -rw-      364072  Nov 12 2014 16:36:10 +04:00  sboot78xx.10-2-1-12.sbn
      278  -rw-        1228  Nov 12 2014 16:36:32 +04:00  sip78xx.10-2-1-12.loads
      279  -rw-      496521  Nov 12 2014 17:01:40 +04:00  music-on-hold.au
      280  -rw-       23660  Nov 19 2014 14:48:40 +04:00  enter_account.au
      281  -rw-       24164  Nov 19 2014 14:48:48 +04:00  enter_pin.au
    261324800 bytes total (120594432 bytes free)
    my application configuration was like this:
    application
    package auth
      param passwd-prompt flash0:/enter_pin.au
      param max-retries 0
      param term-digit #
      param user-prompt flash0:/enter_account.au
      param abort-digit *
      param passwd 12345
      param max-digits 32
    *****Resolution*****
    changed user prompt and password prompt from flash0:/ to flash:/
    application
    package auth
      param passwd-prompt flash:/enter_pin.au
      param max-retries 0
      param term-digit #
      param user-prompt flash:/enter_account.au
      param abort-digit *
      param passwd 12345
      param max-digits 32
    Right now lpcor is working fine for Long Distance calls with the same config.
    Thanks All

  • Polycom sip phone cme

    has anyone been able to register a polycom sip phone on a callmanager express? i especially need help on configuring the polycom phone

    I just got this to work with a SoundPoint 501. Took some fiddling, but phone is registered and seems to work Ok. Still working on some issues with WMI and getting the messages button to work correctly, but the phone is registered.
    here is the config:
    voice register global
    mode cme
    source-address 10.72.13.19 port 5060
    max-dn 200
    max-pool 20
    timezone 13
    tftp-path slot0:
    create profile sync 0390651099874124
    ntp-server 10.71.13.19 mode directedbroadcast
    voice register dn 1
    number 4020
    allow watch
    voice register template 1
    session-transport udp
    softkeys hold Resume Newcall
    softkeys idle Newcall Redial Cfwdall
    softkeys connected Endcall Trnsfer Confrn Hold
    voicemail 4200 timeout 30
    voice register dialplan 1
    type 7940-7960-others
    pattern 1 4...
    pattern 2 ....
    pattern 3 .
    voice register pool 1
    id mac 0004.F213.2465
    type P600
    number 1 dn 1
    dialplan 1
    dtmf-relay rtp-nte
    voice-class codec 1

  • CME SIP Phone Calls in one-way (inside local network)

    Hello everyone, first time here, need a little help.
    I'm having some trouble to find a solution to the following problem.
    Recently I've installed CME 9.1 using the router 2921. Most of the phones are SIPs, model 3905 (around 20 of them), with the last firmware updated.
    Some users are complaining one way audio issue in internal calls, from a extension to another (only in sip phones)
    With Wireshark capture I could see that RTP packets are being sent and receive by the router and not directly trough the phones. Is this normal in CME? When a call with problems occours (one way audio) there is no audio in one way, but router still sends confort noise packets.
    Here is my config.
    Thanks for any help.
    Martin
    ##################################################################################33
    System returned to ROM by power-on
    System restarted at 11:29:23 BR Tue Jan 29 2013
    System image file is "flash0:c2900-universalk9-mz.SPA.152-4.M2.bin"
    Last reload type: Normal Reload
    Last reload reason: power-on
    voice service voip
    no ip address trusted authenticate
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 10.3.245.1 port 5060
    max-dn 60
    max-pool 70
    load ATA-187 ATA187.9-2-3-1
    load 3905 CP3905.9-2-1-0
    authenticate realm all
    timezone 17
    time-format 24
    date-format D/M/Y
    tftp-path flash:
    file text
    create profile sync 0094230880392697
    network-locale U1
    user-locale U1 load /CME-locale-pt_BR-Portuguese-8.8.2.5.tar
    ntp-server 10.3.244.7 mode directedbroadcast
    voice register dn  1
    number 9006
    name Sala_Reuniao_02
    label Sala de Reuniao 2
    voice register dn  2
    number 9007
    name Sala_Reuniao_03
    voice register dn  3
    number 9008
    name Sala Reuniao 04
    voice register pool  1
    id mac 8478.ACE6.09A2
    type 3905
    number 1 dn 1
    template 1
    codec g711ulaw
    voice register pool  2
    id mac 8478.ACE6.0573
    type 3905
    number 1 dn 2
    codec g711ulaw
    voice register pool  3
    id mac 5897.1ECD.8F8D
    type 3905
    number 1 dn 3
    codec g711ulaw
    interface GigabitEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface GigabitEthernet0/0.220
    encapsulation dot1Q 220
    ip address 10.3.245.1 255.255.255.0
    ip helper-address 10.3.244.71
    h323-gateway voip bind srcaddr 10.3.245.1
    telephony-service
    max-ephones 5
    max-dn 5 no-reg both
    ip source-address 10.3.245.1 port 2000
    timeouts interdigit 5
    timeouts busy 12
    system message  XXXXXXXX
    cnf-file location flash:
    cnf-file perphone
    user-locale U2 load CME-locale-pt_BR-Portuguese-8.8.2.5.tar
    user-locale 2 PT
    network-locale U2
    load 7925 CP7925G-1.4.1SR1.LOADS
    load 6941 SCCP69xx.9-2-1-0.loads
    time-zone 17
    time-format 24
    date-format dd-mm-yy
    max-conferences 8 gain -6
    dn-webedit
    time-webedit
    transfer-system full-consult
    transfer-pattern .T
    create cnf-files version-stamp Jan 01 2002 00:00:00
    ephone-dn  1  dual-line
    number 9001
    ephone  1
    mac-address D867.D9E6.F57F
    ephone-template 1
    type 6941
    button  1:1

    Hi ,
    We have upgarded the the firmware to the  3905.9-2-2ES2 , but show voice register pool phone-load still shows the old firmware, but the phoen itself is showing the new upgraded version on the dsiplay ...any advice is highly appricated,
    ADM-CME9#show voice register pool phone-load
    Pool Device Name     Current-Version             Previous-Version
    ==== =============== =========================== ===========================
    1    SEP7081053DE72F Cisco/SPA502G-7.4.8a                                  
    3    SEP34BDC8C6C412 Cisco-CP3905/9.2.1                                    
    4    SEP34BDC8C64561 Cisco-CP3905/9.2.1                                    
    5    SEP54781AE1F531 Cisco-CP3905/9.2.1                                    
    6    SEP54781AE171D2 Cisco-CP3905/9.2.1                                    
    10   SEP54781AE1F544 Cisco-CP3905/9.2.1                                    
    15   SEP1CE6C77323CD Cisco-CP3905/9.2.1                                    
    16   SEP58971E282A23 Cisco-CP3905/9.2.1                                    
    17   SEP58971E2822A8 Cisco-CP3905/9.2.1                                    
    19   SEP1CE6C77321F3 Cisco-CP3905/9.2.1                                    
    30   SEP54781AE171E2 Cisco-CP3905/9.2.1                                    
    31   SEP54781AE16FD4 Cisco-CP3905/9.2.1                                    
    32   SEP54781AE16F2F Cisco-CP3905/9.2.1                                    
    33   SEP54781A1C77FD Cisco-CP3905/9.2.1                                    
    34   SEP54781A1C77DC Cisco-CP3905/9.2.1                                    
    35   SEP54781AE17527 Cisco-CP3905/9.2.1                                    
    36   SEP54781AE17766 Cisco-CP3905/9.2.1                                    
    37   SEP54781AE1731A Cisco-CP3905/9.2.1                                    
    38   SEP54781AE08B8D Cisco-CP3905/9.2.1                                    
    39   SEP54781AE123B1 Cisco-CP3905/9.2.1                                    

  • Building CME with SIP vs. SCCP Phones

    We currently have 4 CME Systems with SCCP phones. Recently, it was discuss by our upper management to start using SIP phones. Right now the system I have configured are using a PRI for dialtone with POTS lines for backup. What needs to different on the config to use SIP? Do I replace the 'telephony-service' and current 'dial-peers' or add to them?
    This is all new to me and I still have not been able to attend any formal training.
    Would there ever be a reason to use SIP and SCCP phones on the same system and would that even work?
    Any help is appreciated!

    Aha.... that's a different question.
    The choice of your trunking protocol (PRI versus SIP versus something else like FXO/analogue) is largely independent of the protocol the handsets use. You can use SCCP for your handsets and then use SIP trunking into a provider for your external calls. The CME Router will handle the signalling translation between SCCP and SIP for you.
    Like everyone else here, I would always use SCCP for the handsets. Whilst Cisco are improving SIP handset features all the time between releases you still can't do everything you that you can do with SCCP. You would also need version 15 to support some of the more useful SIP handset stuff including Extension Mobility, and my own personal view of the code quality on the version 15 trains would use such language that it can't be mentioned here.
    SCCP to the handset and trunking over SIP is perfectly valid and I've used it many times with great success.
    Hope this helps. Barry

  • CME SIP Phones details not found

    What is the reason couldnlt find the SIP Phones information in CME GUI?

    Because CME GUI DO NOT support sip phones.
    Thanks
    Manish

Maybe you are looking for

  • Can't open downloaded files due to 'unidentified developer'

    Hi, When trying to open an application file download from the internet I get a message window that states: "ROES_Utility" can't be opened because it is from an unidentified developer. According to the reputable company i'm trying to download this fro

  • To Learn Detail of Error Message

    Hi All; We have an executable that i can not debug or reach code, somehow a blackbox. When i execute it, i only get 942 error as i simulated below: SQL> SELECT * FROM no_existed_or_granted_table; SELECT * FROM no_existed_or_granted_table ORA-00942: t

  • Mail 4.4 repeatedly asks for password with OSX 10.6.6

    We have a Verizon internet access and use Mail 4.4 with OSX 10.6.6. On a regular basis we get asked to reenter our password for incoming mail. Is there anything that can be done to make the two compatible?

  • Q: new language features and JVM 1.4

    I just finished reading Joshua Bloch's article on new Java language feature and am looking forward to their introduction. Will programs compiled using the new features (generics, enhanced for, autoboxing, enums, static imports, and metadata) still ru

  • Won't boot from ML USB

    I want to reinstall OS X on my MBP.  It's a 2007 so I thought a reinstall might be good to get rid of all the software I've collected over the years. I plan on reinstalling via a USB I made using Lion Diskmaker.  I boot and hold the option key to get