CME with SPA112
Hi,
We have a 2901 with CME 10 and I have configured some SPA112 devices to connect to DECT phones and FAX machines.
The DECT phones work perfectly, but the with faxes we have issues, it sometimes works, and sometimes it doesn't.
Outbound works sometimes, inbound never works. When we connect a DECT phone to the 'fax' port from the SPA112, the DECT phone works perfectly.
Has anyone install SPA112 with CME and faxes were working fine?
Thanks
JH
Hello Sreekanth,
Sorry for the delay in responding to you.
This is a 2901 with CME 10 and 3 BRI interfaces.
We have 5 SPA112 configured as 3rd party SIP (username/password no type, no MAC)
The DECT phones are working perfectly, and can have a cor list applied and watch command.
Just the faxes don't really work. Sending sometimes work, receiving not at all, fax makes the fax noises and then the line drops.
What would be the best configuartion for SPA with CME 10? using T38 or passthru?
Thanks!
Jan
Similar Messages
-
Hi All,
I would like to know if it is possible to have CME with Jabber. Our customer asks for IM and Presence in a ToIP solution with no more than 70 Users.
I Appreciate your Comments,
regards
GCANo, you need CUCM and CUPS/IM&P
Software Requirements
http://www.cisco.com/en/US/partner/docs/voice_ip_comm/jabber/Windows/9_0_1/b_jabber_win_icg_chapter_01000.html#JABW_RF_SEF029A0_00
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk -
Hey All ,
i have integrated My CME with CUE , i have two phone with extension 1000,2000 and all phones have mailbox,,
i make basic IVR that will forward the call to 1000 if 2000 is busy , but the case is when the 2000 is busy the forwarded call go to the mailbox
Not to 1000 .
how i can make the call go to 1000 NOT to the voice mail ??
but at the same time if any one is call the 1000 OR 2000 direct and the extension is busy will go the mail box.
please help Me...
Best Regards,
Ahmad Kefayathanks for pointing
-
CME with Microsoft Lync/Mediation server Integration
Hello
please, we want to integrate our Cisco CME with microsoft Lyn/Mediation Server.
Please, what do i need to configure on the Cisco CME?
ThanksI have config on cme side. But not Lync side(
sip-ua
no remote-party-id
voice service voip
allow-connections sip to sip
no supplementary-service sip handle-replaces
sip
bind control source-interface gi0/0 (this should be your sip interface, creating loopback and binding to SIP is best practice)
bind media source-interface gi0/0 (this should be your sip interface, creating loopback and binding to SIP is best practice)
voice class codec 20
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 g729r8
dial-peer voice 11 voip (Incoming dial-peer from Lync)
b2bua
session protocol sipv2
session target ipv4:LyncIP
session transport tcp
incoming called-number .%
voice-class codec 20
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 21 voip (outgoing dial-peer to Lync)
destination-pattern 1... (this is Lync patterns dial-peer)
notify redirect ip2pots
session protocol sipv2
session target ipv4:LyncIP
session transport tcp
voice-class codec 20
dtmf-relay rtp-nte
fax rate disable
fax protocol pass-through g711ulaw
no vad -
Building CME with SIP vs. SCCP Phones
We currently have 4 CME Systems with SCCP phones. Recently, it was discuss by our upper management to start using SIP phones. Right now the system I have configured are using a PRI for dialtone with POTS lines for backup. What needs to different on the config to use SIP? Do I replace the 'telephony-service' and current 'dial-peers' or add to them?
This is all new to me and I still have not been able to attend any formal training.
Would there ever be a reason to use SIP and SCCP phones on the same system and would that even work?
Any help is appreciated!Aha.... that's a different question.
The choice of your trunking protocol (PRI versus SIP versus something else like FXO/analogue) is largely independent of the protocol the handsets use. You can use SCCP for your handsets and then use SIP trunking into a provider for your external calls. The CME Router will handle the signalling translation between SCCP and SIP for you.
Like everyone else here, I would always use SCCP for the handsets. Whilst Cisco are improving SIP handset features all the time between releases you still can't do everything you that you can do with SCCP. You would also need version 15 to support some of the more useful SIP handset stuff including Extension Mobility, and my own personal view of the code quality on the version 15 trains would use such language that it can't be mentioned here.
SCCP to the handset and trunking over SIP is perfectly valid and I've used it many times with great success.
Hope this helps. Barry -
How to config CME with FXS card for analog phones
I want to config FXS cards in CME router with SCCP protocol for transfer, pickup ... feature. I can find information about the sccp (the command about stcapp), but I can not find the information about how to config CME, e.g. the phone no.(something like ephone-dn .... )
Can anyone help me ? or send me the link
Thx
DennisThx Johncaston,
Your config is for H323, it doesn't support features, something like transfer funtion .......
I have found the config for SCCP, let's share my finding
====================
ephone-dn 178
number 9933
description Board Room
name Board Room
hold-alert 30 originator
ephone-dn 179 dual-line
number 9990
description Meeting Room 3
name Meeting Room 3
hold-alert 30 originator
ephone 95
mac-address 9556.60FA.0200
type anl
button 1:178
ephone 96
mac-address 9556.60FA.0201
type anl
button 1:179
GigabitEthernet0/0 is up, line protocol is up
Hardware is MV96340 Ethernet, address is 0019.5566.0fa0 (bia 0019.5566.0fa0)
================================
stcapp ccm-group 1
stcapp
sccp local GigabitEthernet0/0
sccp ccm 172.16.136.125 identifier 1
sccp
sccp ccm group 1
associate ccm 1 priority 1
signaling dscp af31
audio dscp ef
voice-port 1/0/0
cptone HK
caller-id enable
voice-port 1/0/1
cptone HK
caller-id enable
dial-peer voice 21 pots
service stcapp
port 1/0/0
dial-peer voice 22 pots
service stcapp
port 1/0/1
=========================
Thanks !!
Dennis -
CME with Unity Express GUI Java problem
Running IOS 12.4(22)T with CME 7.0(1) and CUE 7.1.5 on a 2821 ISR.
The GUI had been working fine after the initial system install (used it provision phones). Got back into the system to add another phone and when clicking on either Configure->Extensions, Configure->Users or Configure->System Parameters we get the following text in the browser (IE, Firefox doesn't matter):
var maxButtonMode = 10 var ringTypeName=new Array(maxButtonMode) ringTypeName[0]= "Normal Ring" ringTypeName[1]= "Silent" ringTypeName[2]= "Silent w/CW Beep" ringTypeName[3]= "Feature Ring" ringTypeName[4]= "Monitor" ringTypeName[5]= "Overlay" //ringTypeName[6]= "Expand" //ringTypeName[7]= "Overlay w/CW" //ringTypeName[8]= "Speed Dial" ringTypeName[9]= "Watch" document.write("<" + "SCRIPT LANGUAGE='JavaScript' SRC='admin_user.js'><" + "/SCRIPT>");
The other pages load up fine. Same behaviour from Windows 7 32-bit or inside a Windows XP SP3 VM environment. Two different versions of Java running: 1.6.0_17 and 1.6.0_20.
Thanks for your help, ideas or suggestions.
JasonEnded up taking these steps to fix the gui issue:
Reloaded the integrated CUE module service module no effect;
Reloaded the router - no effect;
Upgraded to IOS 12.4(24)T3 and extracted cme-gui-124-24T.tar to flash (had been using files from cme-gui-7.1.0.0.tar).
Working fine now. -
Has anyone had any luck configuring CME 4.0 to work with the X-lite softphone?
Works fine. To register the phone, configure username (same as extension number) and password under "voice register pool XX". You will need to specify a mac-adress that in reality doesn't matter and can be all zeros. In X-lite check the box "register with server" and choose "send outbound via proxy" with CME address.
Hope this helps, please rate post if it does! -
CME with telephones analogic in port FXS
Hi all,
I have a router with CME and 4 FXS ports, would like to set up call transfer that is possible with analog phones and FXS port and CME?
RegardsIt's possible, but fiddly - you'd need to have users dial codes etc.
e.g. http://www.cisco.com/c/en/us/td/docs/ios/voice/fxs/configuration/guide/15_1/fxs_15_1_cg_book/fxssccpsplmft.html
Aaron -
How does one intergrate voicemail with Cme,i have an office with a 2811 router with a number of ip phones.It has FXO/FXs ports and is working ok,i now want voicemail,how do i go about this?
Thanks.Your best solution will be Cisco Unity Express voice mail system.
You'll need an NM slot available to put a NM-CUE module into.
(or you can go with an AIM-CUE module which will connect to the 2811 motherboard)
Please see the following links for more info about Cisco Unity Express voice mail:
CUE Introduction:
http://www.cisco.com/en/US/products/sw/voicesw/ps5520/tsd_products_support_series_home.html
CUE 3.1:
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel3_1/release/notes/rncue31.html
CUE Compatibility Matrix:
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/compatibility/cuecomp.htm -
I have a 2801 router with cme and a four ports FXO card, I have a 800 toll free with three lines, any idea on how to configure this type of service?
Is just one telephone number asocciate with 3 physical lines on three port int he cisco fxo card.Yes, this function is configure I make test with all the options in the web page but continues working worng:
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is signal
Answer Supervision is inactive
Hook Status is Off Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 1 -
Hello, I have CME 4.0 with 2 IP Phones Linsys SPA941.The IP Phone register and functionally with the codec g711ulaw, but when use codec g729r8, the calls are tone busy. The codec is configuration on router and IP Phone. The configurations are attached.
Thank you.Hi,
can they call each other in g729? can you call an SCCP phone if the latter is set for g.729 ?
Can you collect and send "term mon" and "debug ccsip message" when trying ? -
Need a sample cme with multiple fxo ports, hunt fashion
hi,
anyone kind enough to provide a sample working configuration of multiple fxo ports (each being a pstn line) and I assuming the telco is doing hunting...
so let's say 4 lines, if line 1 is busy the call is sent by the telco on line 2 and so on...
incoming and outgoing.
thank you very much!!
I did google it and can't find anything with multiple fxo ports.trunk group 1
max-calls voice 4 (or however many POTS lines you want to use)
hunt-scheme round-robin (or whatever method you like)
voice-port 0/0/0
trunk-group 1
connection plar opx XXXX (extension)
caller-id enable
voice-port 0/0/1
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/2
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/3
trunk-group 1
connection plar opx XXXX
caller-id enable
dial-peer voice 1 pots ( I like creating this for troubleshooting, by default cisco router accept incoming calls)
trunkgroup 1
incoming called-number .
direct-inward-dial
dial-peer voice 2 pots
trunkgroup 1
destination-pattern 8[2-9]...... (8 for an outside line or 9 or nothing, then adjust your forward-digits to match)
forward-digits 7
dial-peer voice 3 pots
trunkgroup 1
destination-pattern 81[2-9]..[2-9]......
forward-digits 11
dial-peer voice 4 pots
trunkgroup 1
destination-pattern 8911
forward-digits 3
dial-peer voice 5 pots
trunkgroup 1
destination-pattern 911
forward-digits 3 -
Hi friends,
I'm configuring a CME in order to use ASA phone proxy and I am not finding any guides to configure, does any one could help me ?Hi!
I believe this is what you are looking for:
https://www.myciscocommunity.com/docs/DOC-10763
The document provides a step-by-step configuration guide for setting up Cisco ASA Phone Proxy& CME.
HTH,
Regards,
Teresa.
If it helps, please rate -
Hey all,
i'm running CME 9.1 and i try to use CCP [cisco-config-pro-k9-pkg-2_8-en] it's the latest But is not working ??Hey Michael,
i'm do this :-
Router(config)# ip http server
Router(config)# ip http secure-server
Router(config)# ip http authentication local
Router(config)# username cisco privilege 15 password cisco
Router(config)# line vty 0 4
Router(config)# login local
then when i try to open CCP they open IE and there is no anything that show to connect to the router.
Maybe you are looking for
-
OK to copy a placed image from one document to another?
Hi all, I'm laying out two language versions of an illustrated book. Because they're going to be printed with the same CMY plates (with just the black plates being switched between the languages), the color images need to be in exactly the same place
-
Balance confirmation issue.
Hi All, We are just upgraded our system to ECC 6.0.Now I am doing configuration for Balance confirmation. But in SPRO I got all the settings related to Forms only. & while running F.17/F.18 I have specified Reconciliation date but system is picking o
-
Urgent Help Reqd: Delta Problem....!!!
Hi Experts, Urgent help reqd regarding follwoing scenario: I am getting delta to ODS 1 (infosource : 2LIS_12_VCHDR) from R/3. Now this ODS1 gives delta to Cube1. I got one error record which fails when going to cube (due to master data check).And thi
-
All PDF files on my computer open when I try to just open 1 of them with Acrobat Pro 9
Everytime I try to open a PDF in acrobat pro 9 several other PDF documents open as well (like every single one it can find on my computer). I do not have this problem if I open the file in acrobat 8 pro. Any ideas what I can do to fix this problem? T
-
I have a 7 minute MP3 that I want to edit, however when I drag it into garageband it only pulls in the first 3:30. Any thoughts on why? At the 3:30 mark in the song there is a pause but then it starts back up but for some reason the program won't p