CME, WLC 2504, 3602i and 7926

Hello,
I have a wlc 2504, several indoor 3602i using Cisco 7926. The APs are in flexconnec mode, signal looks good from the 7926 site survey too. Good coverage anywhere from -50 to -65. I can be standing directly under an AP and the 7926 will loose network connectivity and connect again. A site survey was done before AP placements
Most of my system configuration on the WLC are defaults. Any idea why this is happening
Thanks
Nki

Duplicate post #2.

Similar Messages

  • Acs 5.3 and wlc 2504 config with restricted network access

    Hello,
    i submit you the following issue that i'm actually facing:
    i must configure a secured wireless network with access restriction based on SSID. the equipements are : cisco wlc 2504 (soft 7.3) cisco secure acs aplliance 1121 (soft 5.4) .
    the users that will connect to the network are regrouped by identity groups, each identity group having it's own SSID. Clearly each group of users must access only one SSID.
    i followed the procedure below to configure it:
    -- creating user identity groups;
    -- creating users and assigning them to the groups;
    --- creating authorization profiles for each SSID under policy element/ authorization and permission/network access/authorization profiles and putting the Airespace-Wlan-Id(the SSID number) in the radius tab.
    --- assigning the authorization profiles to the identity groups under access policies.
    after all these config the users can access the network using there userid/password configured. But the problem is Every user can access every SSID, seems like the restriction is so not very well configured.
    i found some documentation on this kind of config but the version of ACS used seems older than the one that i use, so menu are very different.
    Please can someone provide with the right steps to follow to achieve this kind of config.
    tkx in advance

    Yes.. you only have to add the end filter like what I posted... as far as the calling station id in the WLC security tab, it doesn't matter because that is not used when using 802.1x.  I would also try to not enable everything that you have just to start from the basic and make sure it works first.  The WAP Authentication Method might or might not work for you.  Uncheck that for now and when you have a successful authentication, look at the monitor log and see what radius attributes are being sent, because those attributes is what you can use to build your policies.
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • DHCP Error with WLC 2504 and Aironet 2600 setup across subnets

    Hey guys
    I have just setup a new WLC 2504 controller to manage a WiFi service that will span 6 geographic locations.  The local networks at each location are on different subnets (all 192.168.x.x) and are linked up via IPSEC VPN links, and there is Active Directory spanning the sites, with DNS and DHCP servers running at each location.
    I tested the WLC at our main office with a single AP, and it worked fine.  The AP set itself up, and wireless devices connect with no probs. Great!  Yesterday I headed out to one of our remote sites, and connected an AP to their network - and that seemed to work fine too.  Within a few minutes I was able to see the WiFi network I'd setup, and my smartphone connected to it straight away (as I'd rpeviously connected at the main office), so I was pretty happy that all was working well.
    This morning however I've had notification that wifi performance at the remote site isn't great.  I've got someone to check their ip address, and I've found that their IP address and default gateway match the LAN at the main office where the WLC is based - NOT the LAN where the wireless client is.  Obvioulsy this is not ideal!
    So I guess my question is, what have I done wrong?  (I guess I HAVE done something wrong!?).  And how can I get wireless clients at remote sites to pick up an IP from the DHCP server at THEIR site?
    Any help would be greatly appreciated! 
    Thanks!           

    Hello Tim,
    What mode your APs are in? Local mode? or FlexConnect mode?
    If local mode, then all the traffic will be tunnelled to the WLC and they'll be same as if you are connecting from the WLC location.
    If you use FlexConnect APs (which is recommended for remote sites) you can configure FlexConnect groups on the WLC and add each location in a specific group. In that group you can decide what VLAN the users should be in.
    Check this link for FlexConnect group configuration
    http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html#wp1230080
    HTH
    Amjad
    Rating useful replies is more useful than saying "Thank you"

  • Best practices for network design on WLC 2504 and 5508

    Dear all:
    I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
    Maximum amount of AP per port
    The scenario when to use all ports in both WLC
    Maximum number of clients(users) per port
    Bandwidth comsumption of  management vs data in order to assign one port for management
    I've just found this:
    Cisco 5508 controllers have eight Gigabit Ethernet distribution system ports, through which the controller can manage multiple access points. The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller. Cisco 5508 controllers have no restrictions on the number of access points per port. However, Cisco recommends using link aggregation (LAG) or configuring dynamic AP-manager interfaces on each Gigabit Ethernet port to automatically balance the load. If more than 100 access points are connected to the 5500 series controller, make sure that more than one gigabit Ethernet interface is connected to the upstream switch.
    http://www.cisco.com/c/en/us/td/docs/wireless/controller/6-0/configuration/guide/Controller60CG/c60mint.html
    Thanks for your help.

    The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller.
    This is an old document.  5508 can now support up to 500 APs if you run firmware 7.X.  2504 can support up to 75 APs if you run firmware 7.4.X.
    I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
    Best practice and recommendation is to LAG all ports so you will be able to form a link redundancy.  If one link goes down, you have other link to push traffic. 

  • Please help me to configure 2504 WLC as secondary in N+1 HA mode. My primary WLC is 5508 and both have 50 AP license.

    Please help me to configure 2504 WLC as secondary in N+1 HA mode. My primary WLC is 5508 and both have 50 AP license. I want to deploy the AP in the same location.

    Go HERE:  https://supportforums.cisco.com/discussion/12219106/high-availibility-2500

  • Guest wireless with WLC 2504, Catalyst 4510R+E and ASA 5510

    I need to add guest (internet only) wireless to our existing internal wireless and am looking for advice as to the best practice configuration. Existing infrastructure as follows:
    WLC 2504
    1142 LAPs
    4510R+E
    ASA 5510
    Existing configuration as follows:
    WLC management interface and APs addressed on the 192.168.126.0 /25 network
    Internal WLAN mapped to the management interface
    Management interface VLAN ID 0 (untagged) and dynamic AP management enabled
    WLC port 1 (only) connected to 4510 via trunk with native VLAN set to 7 and allowed VLAN set to 7
    4510 connected to ASA inside interface (security level 100)
    Switchport on 4510 connected to ASA configured as switchport access VLAN 99 (our internet VLAN)
    ASA inside interface NOT configured for subinterfaces and is addressed on the 192.168.121.0 /25 network
    What is the best way to add guest wireless to our existing configuration?
    Note: I need the guest wireless to be filtered by Websense as our internal wireless is
    Any advice would be greatly appreciated!

    Thank for the reply Scott. The configuration recommendations from Yahya did not work. I set up as he recommended and also added a dhcp scope on the wlc. Client gets dhcp but cannot even ping the wlc much less anything else. Yahya stated above to configure port 2 on the wlc to an access port on my 4510. Aren't all connections from the wlc supposed to be trunk links to the switch? Shouldn't I just leave the management interface on the wlc untagged and add a dynamic interface for each wlan and tag it with the approriate vlan id? And then leave the (one) physical connection on the wlc (port 1) connected to a trunk link on the 4510 that allows the required vlans?
    Any input would be greatly appreciated...
    JW

  • Cisco WLC 2504 and ways to authenticate users

    Hi All,
         What is the ways to make user authenticate to WLC 2504 and what is the best and simple way and what is the differences btw each method _i mean for example need radius server or something else to be exist_ ?
         and any one can give me case study for this issue
    System consist of Cisco 2504 and Cisco LAP 1140
    Thanks

    To implement radius based authentication is the best practice for the small & enterprise environment.
    Information About RADIUS
    Remote Authentication Dial-In User Service (RADIUS) is a client/server protocol that provides centralized security for users attempting to gain management access to a network. It serves as a backend database similar to local and TACACS+ and provides authentication and accounting services:
    •Authentication—The process of verifying users when they attempt to log into the controller.
    Users must enter a valid username and password in order for the controller to authenticate users to the RADIUS server. If multiple databases are configured, you can specify the sequence in which the backend database must be tired.
    •Accounting—The process of recording user actions and changes.
    Whenever a user successfully executes an action, the RADIUS accounting server logs the changed attributes, the user ID of the person who made the change, the remote host where the user is logged in, the date and time when the command was executed, the authorization level of the user, and a description of the action performed and the values provided. If the RADIUS accounting server becomes unreachable, users are able to continue their sessions uninterrupted.
    RADIUS uses User Datagram Protocol (UDP) for its transport. It maintains a database and listens on UDP port 1812 for incoming authentication requests and UDP port 1813 for incoming accounting requests. The controller, which requires access control, acts as the client and requests AAA services from the server. The traffic between the controller and the server is encrypted by an algorithm defined in the protocol and a shared secret key configured on both devices.
    You can configure multiple RADIUS accounting and authentication servers.For example, you may want to have one central RADIUS authentication server but several RADIUS accounting servers in different regions. If you configure multiple servers of the same type and the first one fails or becomes unreachable, the controller automatically tries the second one, then the third one if necessary, and so on. 
    For more Information : http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_security_sol.html#wp2149947

  • Savant and WLC 2504

    The customer have 1x WLC 2504 and 7x AP 3502i.
    He are installing a automation system called Savant, this system use the Bonjour protocol to discovery the services on the network.
    I've configured the multicast group on controller and switch (SG300) with IP 239.xxx.xxx.xxx, but the Savant (on iPad) don't finds the service.
    Somebody has gone through a similar scenario?
    I've used this document: http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0080bb1d7c.shtml
    PS: The customer haven't VLAN
    Best regards.

    #Disable mdns/bonjour on wlc. place the WLC Management and AP vlan on same subnet. keep the savant server and iphone on same wlan and try.
    #WLC 2500 supports only Multicast to Multicast for AP mode, be sure that wired side Multicast is configured properly and working.
    #Try with any standard app to verify bonjour and AP mode multicast works.
    #it is possible there may be any specific string that require to be added onto bonjour profile for savant to work. do debug mdns all enable and see what is missing.
    it is suggested to open TAC case for troubleshooting.

  • WLC 2112 and WLC 2504

    This might be a really stupid question but I need to ask just so that I get a definitive answer. I have a customer that is using a WLC 2112 and has maxed out the licenses for the WLC. I have suggested for him to purchase a 2504 with 30 or 40 licenses to replace the existing 2112. He doesn't want to purchase 30 to 40 licenses and doesn't want to remove the 2112 from the network environment. He would rather purchase a WLC 2504 with 15 licenses and just add that into the network.
    My question is, will there be a problem running a 2504 and a 2112 on the same network? Or can I just make one a primary and one a secondary?

    That should be fine. Just make sure the WLCs are running the same code version and everything should work fine. This is required for APs failover from one WLC to another. You don't want the APs upgrading or downgrading code versions every time the ap moves from the primary to the secondary WLC.
    Sent from Cisco Technical Support iPhone App

  • Why LAP1131AG and LAP11412 cannot to join WLC 2504?

    I have WLC 2504, Cisco LAP1131AG and then Cisco LAP1142N. Why LAP1131AG and LAP11412 cannot to join WLC 2504?
    this is error code at the Cisco LAP1131AG
    *Sep 12 19:30:27.730: %CAPWAP-3-ERRORLOG: Go join a capwap controller 
    *Sep 12 19:30:27.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
    *Sep 12 19:30:57.001: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
    *Sep 12 19:31:27.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.100.10:5246
    *Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Sep 12 19:31:32.085: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Sep 12 19:31:32.117: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !! 
    *Sep 12 19:31:32.118: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Sep 12 19:31:33.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Sep 12 19:31:33.112: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Sep 12 19:31:33.117: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Sep 12 19:31:34.104: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Sep 12 19:31:34.111: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Sep 12 19:31:34.142: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Sep 12 19:31:34.147: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Sep 12 19:31:34.152: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Sep 12 19:31:35.141: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Sep 12 19:31:35.146: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Sep 12 19:31:35.170: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Sep 12 19:31:36.171: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    this is version LAP1131AG
    AP0018.18fc.fd58#sh version 
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(25e)JAO6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 22-Aug-14 10:07 by prod_rel_team
    ROM: Bootstrap program is C1130 boot loader
    BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
    AP0018.18fc.fd58 uptime is 9 minutes
    System returned to ROM by power-on
    System image file is "flash:/c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6"
    and then this is version WLC2504
    (Cisco Controller) >show sysinfo 
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.6.130.0
    Bootloader Version............................... 1.0.20
    Field Recovery Image Version..................... 7.6.101.1
    Firmware Version................................. PIC 16.0
    Build Type....................................... DATA + WPS
    System Name...................................... Cisco_47:19:c4
    System Location.................................. 
    System Contact................................... 
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
    IP Address....................................... 192.168.100.10
    Last Reset....................................... Software reset
    System Up Time................................... 0 days 0 hrs 36 mins 45 secs
    System Timezone Location......................... 
    System Stats Realtime Interval................... 5
    System Stats Normal Interval..................... 180
    --More-- or (q)uit
    Configured Country............................... ID  - Indonesia
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +34 C
    External Temperature............................. +40 C
    Fan Status....................................... 4100 rpm
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 1
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ 24:E9:B3:47:19:C0
    Maximum number of APs supported.................. 5
    IP Address management WLC : 192.168.100.10/24
    IP Address LAP1142N :192.168.100.102/24
    IP Address LAP1131AG : 192.168.100.101/24
    Can anyone help my problem?

    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected]
    cisco AIR-LAP1142N-A-K9 (PowerPC405ex) processor (revision A0) with 90102K/40960K bytes of memory.
    Processor board ID FGL1439S15W
    PowerPC405ex CPU at 586MHz, revision number 0x147E
    Last reset from reload
    LWAPP image version 7.6.130.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: C8:4C:75:79:EB:E9
    Part Number                          : 73-12836-03
    PCA Assembly Number                  : 800-33767-03
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC14234D8Z
    Top Assembly Part Number             : 800-33775-02
    Top Assembly Serial Number           : FGL1439S15W
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1142N-A-K9  
    cisco AIR-LAP1131AG-A-K9 (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
    Processor board ID FTX1026T46E
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    LWAPP image version 7.6.130.0
    1 FastEthernet interface
    2 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:18:18:FC:FD:58
    Part Number                          : 73-8962-09
    PCA Assembly Number                  : 800-24818-08
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC102513DE
    Top Assembly Part Number             : 800-25544-06
    Top Assembly Serial Number           : FTX1026T46E
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1131AG-A-K9  
    Configuration register is 0xF

  • Configuration of Cisco WLC 2504 with Local LAN static IP and DHCP

    I want to configure Cisco WLC 2504 with Local LAN static IP and WLC 2504 with DHCP so that APs can be connect with controller.
    Currently i am using WLC 2504 with DHCP so can anyone suggest how to do that..

    Hi Sandeep
    The info is correct, if we're using code below 7.3.101.0.
    This issue is fixed via the below bug id.
    CSCto01390 Unable to ping AP's directly connected to a 2500 controller
    check the fix that is updated on 7.4, 7.5 RNE.
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn75.html
    Note
    Directly connected APs are supported only in Local mode.
    http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps11630/data_sheet_c78-645111.html
    For quick and easy deployment Access Points can be connected directly to 2504 Wireless LAN Controller via two PoE (Power over Ethernet) ports
    Thanks
    Saravanan

  • WLC 2504 don't work with mode trunking dot1Q with 3560cg and 2960cg?

    Hi 
    I have a proble with the 3560cg and 2960cg, when i configure the port with "switchport trunk encapsulation doi1q " and "switchport mode trunk" on the interface for the connection with the WLC2504, don't have connection.
    I configure others WLC and others switch catalyst (2960, 3550, etc) with the same configuration and this connection work very well.
    this is the date from the terminals:
    Model                               SW Version            SW Image                 
    WS-C2960CG-8TC-L   12.2(55)EX2           C2960c405ex-UNIVERSALK9-M
    Model                                SW Version            SW Image                 
    WS-C3560CG-8TC-S   12.2(55)EX2           C3560c405ex-UNIVERSALK9-M
    WLC 2504    IOS-> 7.3.
    I don't know what its hapend, or if i need use another command for the 3560cg and 2960cg
    Regards

    Hi scot
    in my case, i configure the 3560 with the vlan 1 for administration and the vlan 100 and 200 for my clients (i use the 2 vlans with 2 wlans from the wlc) and i know that the port must be Trunk, my management interface its taggin with the vlan 1 for the administration and the dynamic interfaces with the respective vlan.
    when i configure the 3560 and 2960 i use these command (switchport mode trunk) and i loose the connection with the wlc (i use the same comand with other switch and work very well), the wlc loose the conection with the net.
    i dont know the reason for this failure, and i know if the wlc have management interface untugged, only work with this vlan (vlan native or vlan access) and don't work with the others vlans for the wlans.
    I wish to know if the IOS or if exist another configuration for the 3560 and 2960 works with the WLC correctly or its problem of the IOS
    Thaks for the help
    Regards 

  • C3850 WLC enabled and WLC 2504, which one should be Primary controller.

    I have 2 designs to make a better solution, please advise me.
    I have C3850 and WLC 2504.
    1. I will use C3850 as mobility controller (MC) and mobility agent (MA) for WLC 2504. Does it work? or
    2. I will use WLC 2504 as MC and MA for C3850.
    Can I do both of design?
    Which one is better?
    Please recommend me a solution.
    Thank you in advance.

    Hi
    2504 (or any legacy WLC) itself having MC/MA & we cannot separate that role on it. You can seperate MC & MA functionality in Converged Access product platforms (3850/3650) only.
    Therefore here are the answer to your queries
    1. You can have a 3850 with MC/MA functionality. But your 2504 will be a separate controller on your mobility domain. You can allow roaming between these two systems configuring them as mobility peers. You cannot register 3850 connected APs to any other controller other than 3850 WLC itself.So you cannot use these two different system as high availability for AP.
    You need to have min 7.6.x  on your 2504 in order to configure mobility between 2504 & Converged Access system.
    Here is a reference post how you configure roaming between 5508 & Converged Access MC (5760/3850/3650)
    http://mrncciew.com/2014/05/06/configuring-new-mobility/
    2. None of the documents listed the 2504 could act as MC for 3850/3650(MA). So my understanding is you should have 5760/5508/WiSM2/8500 as MC. But you can test it & see whether 2504 could act as MC which I doubted.
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • 3602I and or 3602E Iphone Connection Problems

    Hi,
    We are using two WAP devices and are both experiencing the same issue.
    WLC Controller 2504 (running 7.3.101.0)
    WAP Devices 3602I and 3602E
    The issue we are having is that Iphones cannot connect and or at times see the SSID's that are enabled. Sometimes the SSID's will show up and then dissapear.
    I can have the Iphone sitting right next to the WAP and it not even show up and when it does show up when I try to connect it either fails or the connection is so bad that when doing a speed test it times out.
    I have 3 different Iphones some running the latest IOS 6 and some still on IOS 5 for testing.
    Android Devices are working flawlessly
    Windows and OSX laptops and desktops are working flawlessly
    I have tried a number of options that are suggested here in the community but nothing seems to be working.

    Hi Scott,
    I have tried using the settings that you suggested and although I am able to connect the speeds are pitiful. I have attached screen shots of my speed test and configuration within the controller. I am having great results with 5GHz devices. IPAD, MacBook Pro, Mac Book Air, Android devices.

  • Client got not connection to wlan over wlc 2504 on 802.11b/g

    Hi everybody,
    We are using a wlc 2504 with 7.6.100.0 and AP 1532e.
    I have the strange observacion that only clients with 802.11n (2.4GHz) can connect to the WLAN. Clients thats works only with 802.11b/g, they can't connect to the WLAN. Affected are all machines which want to connect with 802.11b/g.
    This is a MESH WLAN with 5GHz backhaul and 2.4GHz for the user.
    During the debugging found the following:
    *apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:42.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:44.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:44.650: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:46.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 1
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:54.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:56.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:58.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 2
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:03.772: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:05.849: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:07.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:09.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 3
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Blacklisting (if enabled) mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to START (0) last state 8021X_REQD (3)
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Reached FAILURE: from line 5274
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 9) in 10 seconds
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:15.691: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:15.878: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:18.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:20.049: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:22.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *osapiBsnTimer: May 09 11:45:32.048: 00:1b:77:b4:34:e0 apfMsExpireCallback (apf_ms.c:625) Expiring Mobile!
    *apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 apfMsExpireMobileStation (apf_ms.c:6632) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Disassociated
    *apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 45) in 10 seconds
    Thanks for any advice

    In some of the big name brands of wireless, there is "no such thing" as 802.11n on a 2.4 Ghz.  No such thing because Cisco won't allow you (any more) to do channel bonding of 2.4 Ghz.  It doesn't make any sense to bond an already restricted 2.4 Ghz non-overlapping channel (three) and squeeze this number down to two.  
    Can you check to ensure that the data rates for 802.11b are enabled?  Maybe someone disabled data rates from 1 Mbps to 11 Mbps.

Maybe you are looking for

  • Double click to fill in forms?

    How do I turn off the double click when filling in online forms on iPhone 4? It's driving me nuts because my old iPhone didnt do this! Claire

  • CS5.5 Error:6 Help

    So I was trying to install CS5.5 Design Premium and got this message: Exit Code: 6 -------------------------------------- Summary -------------------------------------- - 0 fatal error(s), 9 error(s), 30 warning(s) WARNING: DW065: Display requirement

  • Make a white background with white object is possible? without shadow!

    i m contributor photographer in most microstock, i try to make a white backgournd with white object but with lightroom 4 it isn't possible, i think the program have probelm to select white object and white background, i see internet site microstock a

  • The Java Runtime Environment

    When I need to use java I get several error messages as: The java runtime environment cannot be loaded. And Java(TM) Plug-in Fatal error. Several java virtual machines running in the same process caused an Error. I have no idea what to do.

  • Connecting multiple hard drives - best method?

    I have 4 external hard drives and I was wondering what was a better connection strategy for connecting them to my imac: 1. Connect them all via usb to a usb hub and then the hub connected directly to one usb port on my imac. OR 2. Connect one of the