CNN HD,,,,,problems with signal/feed?

I am in the SE part of the US - SWFL to be exact. I am wondering if anyone else might be experiencing signal issues with CNN HD? It seems like it skips and freezes up momentarily several times within a 2-3 minute period, and always seems to occur after 2:00pm ET ..... CNN SD does not have this issue - just the HD version.

I am having the same problems I reported it to support however they said they fixed it. I still have the problem about every 2 hours my audio skips and the screen looks like the video is intermitting with little squars all all over the screen. They were sending a teck over but it doesn't happen all the time. Like yesterday it did it about 8 times. I only happenes to CNN and it is on 2 TV's with different boxes. I am in the Hudson Florida area.

Similar Messages

Problem with RSS feeds in AppleMail

If anyone can help, I would greatly appreciate it. I have several RSS feeds that come in through AppleMail. Every so often, it stops receiving all of the feeds (I get an explanation point next to the the RSS header). After a day or so, it will start receiving feeds again. I have no problem getting e-mails... just my RSS feeds. Does anyone have any ideas?
Thanks!

I have just experienced the same problem with RSS feeds through AppleMail. A couple of days ago (just after I had upgraded to Aperture 3 - not sure if that's relevant) the exclamation mark appeared next to all the Mailboxes for my RSS feeds, and has not disappeared. If I click on the exclamation mark I get the message "there was an error updating the RSS feed 'Apple Hot News'. The RSS feed is temporarily unavailable because an internal error occurred".
I have tried shutting down, and deleting the RSS plist - with no effect.
Other details - the problem exists on a MacBook Pro, running Sno (v 10.6.2 - all updates applied) and Apple Mail v4.2. I can send / receive regular email. I also have an iMac (also running Sno 10.6.2 and Apple Mail v4.2) - RSS feeds work fine on this machine. Both machines use the same wireless broadband router.
Grateful for any help. Thanks

My iphone 5 has a problem with signal

My iphone 5 has a problem with signal, it always search for network. I had removed and plug sim card again but it doesn't work. Then I restore the iphone, and an exception was throw "... An unknown error has occured (3)."

unknow error 3 means the computer has lost communication with the device during the restore. It can be anything from bad cable, USB port, phone hardware etc.
Since your phone had a signal issue before, it would be your baseband chip faulty and when the restore tries to connect with the baseband chip to check (it does this when you restore) it waits till the chip responds then times out when it doesnt get any response. The restore will try this several times then eventually restart the phone to get out of the loop. As the phone gets restarted (or shutting off) itunes think the phone turned off and throws error 3.
Go to apple if it's under warranty. If not try to find where they do chip replacement as this is not something that you can do yourself.

What is the problem with my feed ?

Can anybody shows me where is the problem with this feed :
<?xml version="1.0" encoding="UTF-8"?>
<rss xmlns:itunes="http://www.itunes.com/dtds/podcast-1.0.dtd" version="2.0">
<channel>
<title>F Communications Podcast</title>
<link>http://www.fcom.fr/</link>
<language>fr-fr</language>
<itunes:subtitle>Electronic With No Limit</itunes:subtitle>
<itunes:author>F Communications</itunes:author>
<itunes:category text="Music"></itunes:category>
<item>
<title>F Com Podcast #1</title>
<itunes:author>Laurent Garnier</itunes:author>
<itunes:subtitle>Essential Mix - November 1995</itunes:subtitle>
<itunes:summary>
01. Felix Da Housecat - Submarine - Radikal Fear
02. LA Williams - Terminal Velocity - DJax
03. ???? - ???? - ????
04. Woody MacBride - Units - Head In The Clouds
05. Laurent Garnier - Rochando O Bico - F Com
06. Steve Stoll - Universal - Proper
07. Scan X - Blue - F Com
08. Electronic Exp - Meltdown Ride - Transparent Sound
09. Reload - Birth Of A Disco Dancer - Warp
</itunes:summary>
<enclosure url="http://younderboy.free.fr/fcom/essentialmix.mp3" type="audio/mpeg" />
<itunes:duration>XX:XX</itunes:duration>
<pubDate>Thu, 16 Nov 2006 19:07:00 GMT</pubDate>
</item>
</channel>
</rss>
When I enter its URL in iTunes, it doesn't reject my feed, but nothing happens. I can see the URL instead of my Podcast's title, like on this caption : http://younderboy.free.fr/caption.jpg
Help me please, I don't understand where is the problem ! Thanks a lot...

Go to this site - http://feedvalidator.org/
And give it your feed URL.

LASERJET P2015-PROBLEMS WITH PAPER FEED

We have a HP LaserJet P2015 in the office. When the paper reaches the halfway point, the printer makes a horrible sound and will not feed the paper. Anybody have any suggestion?

So, I cranked up my old PowerBook G4 (OS 10.4.11) which has the older driver for the P2015dn and the problem remains.
I have made some progress: If I want to print with paper feed from Tray 1, I pull Tray 2 out a few inches, load the paper in Tray 1, start the print job, and the yellow Attention LED flashes indicating an error. Note that the Paper Out light does NOT come on. So I press the Go button, the Attention LED goes out, and the print job completes using the forms in Tray 1 as desired.
So I'm thinking now, What Error condition? and why does clearing it make it print?
Certainly seems like a hardware problem to me as this is NOT the way the printer is supposed to work as documenetd in the User Guide.

I have read up, and am still having problems with RSS Feed

Greetings Everyone.
I really need some help with my RSS feed before I go insane. I would like to think I know what I am doing, but obviously there is some little (or big!) step I am overlooking.
Ok here is my site: www.drewernst.com it is hosted by asmallorange.com
My pocast is at www.drewenst.com/podcast
This is the rss feed iWeb generated: feed://www.drewernst.com/podcast/The%20Jeff%20and%20Drew%20Podcast/rss.xml
Now, from everything I have read so far - it seems that as long as you get the URL right when you are publishing to a folder, iWeb should do the rest. Also, it is important to put the whole folder containing your podcast in your root web folder otherwise it breaks the feed. Both of these things I have done. (obviously not correctly, or it would be working!)
I read Many tutorials and topics I could find about this, but it still doesn't seem to work for me. Apple suggests taking the RSS feed an pasting it into itunes under Advanced menu "subscribe to podcast" to make sure your feed is valid before submitting to itunes.
When I do this, I get an message saying "there was a problem downloading... An unknown error occurred (-50).
I tried using a feed validator and it came back with so many errors. I just don't know that much about RSS, but i have been working on this for about a month and it's driving me crazy. No one I have asked at the apple store has been any more helpful than to suggest I just buy a .mac account and do it from there(honestly the nerve. wink.) I don't need .mac, I have my own website.
Thanks in advance.
Mr. Rss Crazy,
Drew
Oh, I tried to be as detailed as possible but if I left anything important out, please just ask...I will be watching this like a hawk.
iMac 2.0ghz Core 2 Duo Mac OS X (10.4.8)

So, my web-host said that it's a problem with the RSS feed, not there hosting.
They pointed me to "Feed Validator" which I looked at before. I have a lot of errors.
http://feedvalidator.org/check.cgi?url=http%3A%2F%2Fwww.drewernst.com%2Fpodcast% 2FThe%2520Jeff%2520and%2520Drew%2520Podcast%2Frss.xml
Shouldn't Garageband and iWeb have taken care of these errors. I don't even know how I would correct them. I thought this was supposed to be a 1-2-3 process, like the documentation of both programs said.
Sorry if I sound sarcastic, I am just frustrated.
iMac 2.0ghz Core 2 Duo Mac OS X (10.4.8)

Problems with signal level around the house ????

Hi Guys,
I have had my BT Home HUb 2.0 for just about a month now and after having very little luck with my new laptop which i have replaced twice and am now on my 3rd (Samsung) all working well, i am still having problems with using my laptop with the home hub about my house.
I have strong signal downstairs obviously cause that is where home hub is situated, and it is central to the layout to the house, but if i take my laptop upstairs i have no signal again, i say again as when i first fitted home hub i had good signal upstairs of 3/4 bars. I have tried changing the channel and have found that channel 11 is the one for here.
The only thing i can put it down too is that the other day i tried to get the router set up no more than 5 feet from where it is now as i am also trying to get my old pc tower to work from it too (pc tower has no internal wireless card so have a wireless adapter) but signal again is very poor, since i tried that and also laptop has manufacterer update for a new driver to be installed which i installed which was for the wireless facility on laptop ( which since i have done a system restore ), since all of this i have struggled to get strong signall all around the house only in fromt room as hub is situated in hallway next to front room.
Please help, as i am not having very muchg luck ???
regards
joe-sud

Other external interference maybe.
I had a problem last year with my car remote transmitter not working unless within a few inches of the drivers window.
Using a radio scanner, I found a signal on the same frequency that my remote uses.
After eliminating all other possabilities, including total power down of our house to eliminate ANY of our equipment, I contacted Ofcom http://www.ofcom.org.uk/complain/inter/intbr/ and made a formal complaint.
A few days later the investigator arrived with some really hi tech scanning gear, and within 5 mins had identified the scource was eminating from next door.
He found the culprit....next door had a Sky remote extender which had gone faulty, and was flooding the area with a constant signal.
There is no charge for this service as long as its not your own equipment, which is why I powered off the whole house to see if the problem persisted.
Maybe you could use an extention lead from next door to power your router while turning your mains off to check?

4.2.1 problem with signal

Hi all,
After the installation of the new software 4.2.1 i got problem with the signal on my 3gs, at the beginning was a little problem but within the last 2/3 weeks i need the shut it down several times to get sms sent or call working.
Wat could i do to solve this problem? this is becoming really annoying.
tnx
Andrea

Also, with proper use of the recovery and black point sliders, I'd think it would be pretty rare to really crank those "Advanced" values.
There's a creative side to this brick that I find goes beyond simple recovery. I admit to using it less now that we have the definition slider, but it still allows for a certain "look" that I can't get with the other controls. For that, I use the advanced settings a lot and this is a problem that is entirely new to 2.1.
The problem seems to only be dependent on the Mid slider - the amount in the Shadow slider doesn't seem to matter at all. Even at 1.0 on the Shadow slider, pushing Mid C creates this effect.
Obviously going back to Black Point Comp can alleviate the problem, but there's a limit that didn't exist before.
I just noticed that playing with Radius affects it as well. Of course all of this is tied to the black levels in the picture but again, it didn't used to be this way.

CNN website problems with Comments section. Scroll and post problems

CNN website, myself and other firefox users can no longer scroll up and down inside a comment when making a post.
Often you can not post the comment with the 'post' button unless page is reloaded.
Problem has been occurring for last week or so.
I have confirmed that other uses on CNN have same problems with firefox.
Problem doesn't occur when using I.E.8
Brgds,
John

I have this problem with IE 8. I cannot post comments on CNN.com. I thought CNN.com might have disabled my ability to post comments but am not sure if they have that ability. Thanks for your help!

Problems with signal and wifi

Hi there, I've had problems with my phone signal coming and going the past few days I restart my phone but it doesn't always come back, it's a repeated thing, especially when I'm in my room, texts won't send and my wifi goes off and on when I'm using it and I can't maintain a connection, the wifi itself is fine, it seems to be problems with my phone, please could you help,
Thank you

Hey
I try and check back on threads regularly, but yep, tagging me will notify me.
Hmm, I've had a check on Google and a few people do experience signal loss issues... as you're saying you have WiFi problems too, I believe this may be related to the phone rather than EE.
I had a look and there doesn't seem to be a lot of issues in the area you've told me about. You also mention it works at your friends, so again, location doesn't seem to have any impact on this.
Have you tried removing the SIM card, turning the phone off, inserting the SIM again and then turning the phone on? I'd also remove the SIM, wait 10 seconds and then insert it again whilst the phone is still on.
You may also want to try turning flight mode on and then off again - I read online that this has solved the problem for a few people.
Let me know if any of the above works, and if not, I'll see what other advice I can offer. I can't rule out for certain it's not an EE issue... but we'll soon find out I'm sure!
Thanks,
Titanium

IPad2, having problems with signal strength on WiFi?

On my iMac I have four bars signal strength. On my iPad2 I have one bar and it will not connect to the WiFi.

I have a similar problem.
(But not on Crystal Palace Tx).
Switch to a poor channel. (Dave for example. This is one I have problems with).
Go to Settings, TV Settings, Freeview Signal Strength.
Now press the Info button to get extra information.
Note the UHF channel number, the channel is being received on.
Get the same channel information, on the other Freeview receiver you have.
In my case, the UHF channels are different.
I believe, the Youview box is pre-set to receive from a transmitter (and hence a UHF channel number), determined by a post-code and/or your address details.
Because my aerial is not pointing at the main transmitter for my post code, I get poor reception because the transmitter the aerial is pointing at, transmits Dave (MUX) on another UHF channel.
As confirmed by the other freeview receivers I have.
There doesn't seem to be a way to force the box to use any other UHF channel.
Any scan always comes up with the same one.
There is no manual setting.
I might be totally wrong, but I think this is another software bug.

Problems with signal strength with channels on Mux...

I've had a YouView box (Humax first gen model) for almost a week and i'm having pixelation/signal strength problems with all channels on Mux. Com5, Pick, Dave, Movie Mix and Really etc. My Vision+ box and TV are showing these channels without any problems. Any ideas?

I have a similar problem.
(But not on Crystal Palace Tx).
Switch to a poor channel. (Dave for example. This is one I have problems with).
Go to Settings, TV Settings, Freeview Signal Strength.
Now press the Info button to get extra information.
Note the UHF channel number, the channel is being received on.
Get the same channel information, on the other Freeview receiver you have.
In my case, the UHF channels are different.
I believe, the Youview box is pre-set to receive from a transmitter (and hence a UHF channel number), determined by a post-code and/or your address details.
Because my aerial is not pointing at the main transmitter for my post code, I get poor reception because the transmitter the aerial is pointing at, transmits Dave (MUX) on another UHF channel.
As confirmed by the other freeview receivers I have.
There doesn't seem to be a way to force the box to use any other UHF channel.
Any scan always comes up with the same one.
There is no manual setting.
I might be totally wrong, but I think this is another software bug.

Migrating E&M immediate start from 2821 VGW to AS5350XM but problems with signalling

Hi,
We currently have 2821 VGW platforms running E&M Immediate start. The T1s go into the DACS and the IP interface connects to the SIP server with a simple number plan.
So, when a T1 DS0 signals, the VGW talks to the SIP server, the SIP server does a database lookup and talks back to the VGW and passes the connection details.
However we are now migrating to the AS5350XM platform and replicating the config from the 2821 to the AS5350XM is causing signalling issues.
Here is a sample of the existing 2821 config:
voice rtp send-recv
voice service pots
voice service voip
sip
bind control source-interface GigabitEthernet0/0
bind media source-interface GigabitEthernet0/0
rel1xx disable
min-se 1700
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
controller T1 1/0
ds0-group 0 timeslots 1 type e&m-immediate-start
ds0-group 1 timeslots 2 type e&m-immediate-start
ds0-group 2 timeslots 3 type e&m-immediate-start
voice-port 1/0:0
define Tx-bits idle 1111
define Tx-bits seize 0000
define Rx-bits idle 1111
define Rx-bits seize 0000
timeouts wait-release 1
connection plar 1000
voice-port 1/0:1
define Tx-bits idle 1111
define Tx-bits seize 0000
define Rx-bits idle 1111
define Rx-bits seize 0000
timeouts wait-release 1
connection plar 1001
voice-port 1/0:2
define Tx-bits idle 1111
define Tx-bits seize 0000
define Rx-bits idle 1111
define Rx-bits seize 0000
timeouts wait-release 1
connection plar 1002
dial-peer voice 1000 pots
destination-pattern 1000
port 1/0:0
dial-peer voice 1001 pots
destination-pattern 1001
port 1/0:1
dial-peer voice 1002 pots
destination-pattern 1002
port 1/0:2
dial-peer voice 1 voip
preference 1
destination-pattern .T
session protocol sipv2
session target ipv4:192.168.150.2:5060
session transport udp
voice-class codec 1
voice-class sip options-keepalive retry 1
sip-ua
retry invite 2
timers trying 150
sip-server ipv4:192.168.150.2:5060
Here is the same on on the AS5350xm:
voice rtp send-recv
voice service pots
voice service voip
sip
bind control source-interface GigabitEthernet0/0
bind media source-interface GigabitEthernet0/0
rel1xx disable
min-se 1700 session-expires 1700
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
controller T1 3/0:1
framing ESF
ds0-group 0 timeslots 1 type e&m-immediate-start
ds0-group 1 timeslots 2 type e&m-immediate-start
ds0-group 2 timeslots 3 type e&m-immediate-start
cas-custom 0
define-abcd loop-open 1 1 1 1
define-abcd loop-closure 0 0 0 0
cas-custom 1
define-abcd loop-open 1 1 1 1
define-abcd loop-closure 0 0 0 0
cas-custom 2
define-abcd loop-open 1 1 1 1
define-abcd loop-closure 0 0 0 0
voice-port 3/0:1:0
timeouts wait-release 1
connection plar 1000
voice-port 3/0:1:1
timeouts wait-release 1
connection plar 1001
voice-port 3/0:1:2
timeouts wait-release 1
connection plar 1002
dial-peer voice 1000 pots
destination-pattern 1000
port 3/0:1:0
dial-peer voice 1001 pots
destination-pattern 1001
port 3/0:1:1
dial-peer voice 1002 pots
destination-pattern 1002
port 3/0:1:2
dial-peer voice 1 voip
preference 1
destination-pattern .T
session protocol sipv2
session target ipv4:192.168.150.2:5060
session transport udp
voice-class codec 1
voice-class sip options-keepalive retry 1
sip-ua
retry invite 2
timers trying 150
sip-server ipv4:192.168.150.2:5060
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
What I did notice was the following:
1) When defining loop open and loop closed custom bit configuration is different....on the 2821 you do it on the voice port. On the AS5350, it is not supported on the voice port but appears to be configurable via the T1 controller. I'm not sure if the AS5350 needs any further E&M signalling configuration as the problem lies in the signalling....the AS5350 when the line is cleared down appears to start ringing it again and not following the signalling pattern.
2) When doing a "show voice port" on the AS5350XM does not show E&M signalling, whereas it does on the 2821:
AS5350XM:
5350VGW#sh voice port
DS0 Group 3/0:1:0 - 3/0:1:0
Type of VoicePort is CAS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 128 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is plar
Connection Number is 1000
Initial Time Out is set to 15 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 1 s
Spe country is not configured
Region Tone is set for US
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
lpcor (Incoming):
lpcor (Outgoing):
DS0 channel specific status info:
                                      IN      OUT
PORT            CH SIG-TYPE    OPER STATUS   STATUS    TIP     RING
=============== == ============ ==== ======   ======    ===     ====
2821:
2821VGW#sh voice port
recEive and transMit Slot is 0, Subslot is 0, Sub-unit is 0, Port is 0
Type of VoicePort is E&M
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 128 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is plar
Connection Number is 1000
Initial Time Out is set to 15 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 1 s
Companding Type is u-law
Rx A bit no conditioning set
Rx B bit no conditioning set
Rx C bit no conditioning set
Rx D bit no conditioning set
Tx A bit no conditioning set
Tx B bit no conditioning set
Tx C bit no conditioning set
Tx D bit no conditioning set
Rx Seize ABCD bits = 0000 Custom pattern
Rx Idle ABCD bits = 1111 Custom pattern
Tx Seize ABCD bits = 0000 Custom pattern
Tx Idle ABCD bits = 1111 Custom pattern
Ignored Rx ABCD bits = BCD
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
lpcor (Incoming):
lpcor (Outgoing):
Voice card specific Info Follows:
Operation Type is 2-wire
E&M Type is 1
Signal Type is immediate
Dial Out Type is dtmf
In Seizure is inactive
Out Seizure is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Clear Wait Duration Timing is set to 400 ms
Wink Wait Duration Timing is set to 200 ms
Wait Wink Duration Timing is set to 550 ms
Wink Duration Timing is set to 200 ms
Minimum received Wink Duration Timing is set to 140 ms
Maximun received Wink Duration Timing is set to 290 ms
Minimum seizure Timing is set to 50 ms
Delay Start Timing is set to 300 ms
Delay Duration Timing is set to 2000 ms
Dial Pulse Min. Delay is set to 140 ms
Percent Break of Pulse is 60 percent
Auto Cut-through is disabled
Dialout Delay is 300 ms
Hookflash-in Timing is set to 480 ms
Hookflash-out Timing is set to 400 ms
DS0 channel specific status info:
                                      IN      OUT
PORT            CH SIG-TYPE    OPER STATUS   STATUS    TIP     RING
=============== == ============ ==== ======   ======    ===     ====
0/0/0:0          01 e&m-imd     dorm idle     idle
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Can anyone advise if further configuration is required on the AS5350XM in order to pass the E&M signalling correctly ?

Well for me the forms were ok to open with 11g, just had to correct differences and recompile to run.
That there script is a ton of help!..well you forgot to mention the Output_File parameter, but I could find that myself now that I knew what to look at. Now if I could also set it not to produce .err files when everything went fine and to set the output names so that the old compiled forms get overwritten..
the SRW.* calls turned out to be things used in Reports, so it was hopeless to compile in forms..but also not needed
as for ENABLE_ITEM and DISABLE_ITEM I found these to use as their definitions in a library, that proved sufficient.
procedure enable_item
( p_menuName in varchar2
, p_menuItemName in varchar2
) is
v_menuItem menuitem;
begin
v_menuItem := find_menu_item(p_menuName||'.'||
p_menuItemName);
if (not id_null(v_menuItem))
and (get_menu_item_property(v_menuItem,visible) = 'TRUE')
then
set_menu_item_property(v_menuItem, enabled, property_true);
end if;
end;
procedure disable_item
( p_menuName in varchar2
, p_menuItemName in varchar2
) is
v_menuItem menuitem;
begin
v_menuItem := find_menu_item(p_menuName||'.'||
p_menuItemName);
if (not id_null(v_menuItem))
and (get_menu_item_property(v_menuItem,visible) = 'TRUE')
then
set_menu_item_property(v_menuItem, enabled, property_false);
end if;
end;Some forms still playing with me, but the compilation issues there don't seem to be connected with this topic..and now I got issues with reports >.< but that requires a topic elsewhere. Thanks all!

Problems with rss feeds in Firefox.

When i enter an rss feed url into firefox, it automatically switches to safari to open the url. Firefox is my default browser; I am trying to set up rss feeds in Firefox. How do I prevent this from happening so that these urls will open in Firefox?

wast3 wrote:I have this too. Green background when gst-vaapi is installed. Totem is also affected. VAAPI itself works fine in mplayer and vlc. First generation Core i7 here with Intel HD Video. Has been like this for months now...
Same problem here... And in this thread some experience the same behavior: https://bbs.archlinux.org/viewtopic.php … 1#p1480991
Edit: Package name is now gstreamer-vaapi
Last edited by neo1973 (2015-02-12 09:25:25)

Intermittent problems with signal

I haven't sen any reports of signal related issues as a result of firmware updates.
Your signal strength on dish input 1 is a bit weak and may be the cause of the pixelation on live TV. The signal on dish input 2 looks fine, which is probably why your recordings are ok. It's dish input 2 that is used for recordings unless you're recording two things at the same time in which case dish input 1 is also used.
You could try swapping the two dish inputs at the back of your Sky box to see if the weak signal then transfers to dish input 2. Do switch the box off at the plug before you do this. Also be careful to line up the connectors with the sockets before reconnecting them, otherwise you can easily bend the 'pin' in the middle of the plugs, which will make matters worse!
If the pixelation then occurs on recordings and not live tv, it points to a cable or LNB problem. If it stays on live tv, it points to a box issue.

Hi Most days now on firstt turning on the sky box we see the message no signal being received. If the box is switched off and on all channels then load but sometimes the signal breaks up while watching a programme and the sky box has to be switched off again to put it right. When checkingl signal strength when there is a problem these are the readingsInput 1 - Strength 4Quality- 9Input 2- strength 8Quality 9 The problems don't occur every day and I have checked the cables I don't understand how we can wAtch it for days without issue but then this happens.Is there anything you could suggest we check?Recordings are fine Thanks

CNN HD,,,,,problems with signal/feed?

Similar Messages

Maybe you are looking for