Codecs for OCS

Hi,
we have CUCM 7.0.1 & CUPS 7.0.2 integrated with OCS, with the MOC client setup as a remote destination for each IP Phone. Everything is located at HQ site with two branch sites hanging off the main site.
From my understanding is that OCS only does G711, so my question is how does the remote branch speak to a MOC client at the HQ site.....in other words if a remote branch IP Phone dials a HQ IP Phone it is G729 but the call is answered on the HQ MOC client and so the call fails.
how does one get around this?
thnx
charl

I don't know anything (although I would be shocked if new DNG variants are "proprietary", probably documentation and other support for it is just lagging - this a guess), except it could be that the DNG enhancements are part of the 1.4 spec and that the codecs only support up through 1.3.
Note: ACR version (e.g. 6.6, 7.1) is not the same as DNG version (e.g. 1.3, 1.4).
There's a reason they call it the bleeding edge...
If it's any consolation, exiftool does not support v1.4 yet either.

Similar Messages

  • CUP 8.6, CUCM 8.6 for OCS RCC

                   hi we have the cup8.6, cucm 8.6 integrated to OCS for RCC.
    All dashboard and system checks on cup are ticked ok. However on user MOC client we get the following error : 'cannot connect to the phone system, the call control server may be temporarily unavailble'    .
    we have trunk from ccm to cup, in cup we have ACL's for OCS and in cup we have cti gateway and ctigw application user with 8 cti cucm's.
    User was on a cup 7, with ccm 7 to same ocs and all worked fine, issues after migration to ccm 8 . Move user back to ccm 7, i.e. register the phone to old ccm and using cup 7 all works fine again.
    Any advise appreciated.

    CUPS or IM/P as its called now in version 9.x doesnt require a license. You just need the UCM license which I know is available on the website. IM/P works with CUCM from version 9.x and its tightly integrated as far as version goes.
    Please rate useful posts.

  • Im trying to put songs i just purchased into my video on windows movie maker and the error comes up that the codec for the song is missing what do i do?

    It's for my grandfathers funeral video tomarro and i can't get the songs i just purchased on itunes to work.  They play but wont work when i drag them to the movie maker program.  it says that the codec for the song isn't installed. codec?

    werm21 wrote:
    It's for my grandfathers funeral video tomarro and i can't get the songs i just purchased on itunes to work.  They play but wont work when i drag them to the movie maker program.  it says that the codec for the song isn't installed. codec?
    The songs you purchased are in AAC format, which Windows Movie Maker cannot handle.  You can use iTunes to make MP3 versions by following this guide:  http://support.apple.com/kb/HT1550 and the MP3s will work fine.
    Note that when iTunes does a conversion it creates a new file and leaves the original in place.  Make sure you are grabbing the new MP3 for your movie and not the original AAC.
    Sorry to hear about your grandpa.

  • Remove password expiration time limit for ocs users

    Hello,
    I want to know how to remove password expiration time limit for ocs (11gR2) users? In our system all user accounts are getting expired in 1 week. I have to remove expdate. (profile was changed)
    Thx

    SQL> select * from dba_profiles where RESOURCE_NAME LIKE 'PASSWORD_LIFE_TIME';
    PROFILE RESOURCE_NAME RESOURCE     LIMIT
    DEFAULT PASSWORD_LIFE_TIME PASSWORD     180
    MONITORING_PROFILE PASSWORD_LIFE_TIME PASSWORD     DEFAULT
    SQL> ALTER PROFILE DEFAULT LIMIT PASSWORD_LIFE_TIME UNLIMITED;
    Profile altered.
    SQL> select * from dba_profiles where RESOURCE_NAME LIKE 'PASSWORD_LIFE_TIME';
    PROFILE RESOURCE_NAME RESOURCE     LIMIT
    DEFAULT PASSWORD_LIFE_TIME PASSWORD     UNLIMITED
    MONITORING_PROFILE PASSWORD_LIFE_TIME PASSWORD
    To change the password for a user:
    alter user username identified by new_password;
    Edited by: hitgon on Apr 30, 2012 7:33 PM

  • Hi all ,anyone knows some usefual Codecs for H.264 live video/audio

    I'm headache about the JMF codecs ,they are too few ,and seems inefficiency, anyone knows pure java codecs for H.264 or MPEG4 ?And I think it's better a open source one ,do my thanks , guys!

    Here are some basics....
    FMLE creates RTMP protocol streams that PCs and Macs watch with Flash players.   iOS devices don't understand RTMP (Flash), only HLS delivery of 10 second chuncks of downloaded video playback.  Both systems understand H.264 video, but iOS wants to see AAC audio not MP3.
    You didn't state how you are live streaming, meaning what bandwidth delivery service you are using.  Live streaming only via RTMP won't get you to successful iPad and iPhone HTTP Live Stream.  On-demand delivery to iOS devices normally requires .mp4 video files to be hosted, which Macs and PCs also understand via RTMP delivery.   But unless your delivery service can convert .f4v or .flv files to .mp4 on the fly there is no easy way to to get to iOS via the direct file output of FMLE as of today.   Sometimes we upload live encoded project files to our www.Wistia.com account for PC, Mac and iOS delivery.  This is a YouTube / Vimeo paid type hosting service for on-demand only.
    Some commercial CDNs (Content Delivery Networks) today allow an inbound live RTMP into their system using FMLE.  Then they re-mux that RTMP stream into HLS delivery for iOS.  Some work well using the native MP3 audio codec (Internap), but most require FMLE to have the AAC audio codec installed from Main Concept for $200.  Or people use Wirecast from Telestream which is $500 per license to be able to run two instances on that one license.
    In my 15 years of being a big commercial webcaster here in Silcion Valley, I have yet to find the perfect simple and easy and affordable RTMP to HLS live and on-demand delivery system.  We currently do it different ways with multiple providers depending on the job.  More offerings are coming out now and we try them all as they come down the pike.
    Harvey Louie
    Event Compression Group

  • Enterprise Messenger for OCS 2005 and OS 5.0

    Does anyone know if RIM is working on a release for Enterprise Messenger that will be compatible with Microsoft Office Communicator 2005 that will run on handheld OS 5.0?  They released the OCS 2007/5.0 compatible version 2.7 several weeks ago, but I have not seen the update for OCS 2005/5.0. 

    FYI -- typically, forward looking statements are discouraged on these forums...and authoritative future information is definitely not encouraged...anyone who knows the answer would be barred from revealing it as it would be proprietary information, not for disclosure.
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Best Codec for exporting animations with alpha channel from FCP timeline

    Whats the best codec for exporting animations (hopefully using loseless compression) that will retain alpha channel, and use the current sequence settings for fps and size?
    Currently Im exporting image sequences, but I'd prefer a wrapper.. I don't know much about the 'Animation' export codec.. I did notice that set to current size had some funky value of 753x450 or something.. instead of my current project size of 1920x1080...
    Anyhow.. Just seeing what others are doing..
    basically Im reading out some titles that I'll end up dropping over video later.. but since they render out so slowly (**** lower 3rds is slow) Im trying to get a jump on the process..
    Tx..

    PNG should do it. I think PNG is lossless (that's what they say, anyway). But realistically, if you use PNG, Animation, or JPG2000 set on highest quality, I'd dare you to tell a difference.
    I use PNG because it's supposedly lossless, renders twice as fast as Animation in a FCP timeline, and is usually about half the size.
    If you use "Export Using Quicktime Conversion", you will need to check all of the settings manually to make sure they match your sequence settings. This is always true, no matter what codec you use.
    If that sounds risky, your other option is to go into your sequence settings and change the codec to the one you want to render to (this will probably turn your whole timeline red), and then choose Export -> Quicktime movie.

  • DVCPROHD Codec for Quicktime?

    Wondering if anyone knew where I could download this codec for people without Final Cut Pro. It's for being able to play DVCPROHD Quicktime files on MAC OS X. Thank you!

    Not that I know of...I (would) guess suggesting a workaround would violate FPC licensing.

  • Mountain Lion Spotlight no longer indexes "codecs" for Apple Lossless files?

    Hi, I was recently trying to find some Apple Lossless files stored on my hard drive, and I tried searching using Spotlight's "codec" option (by typing "lossless" into the search field in the Finder). However, nothing came up. Upon further investigation (by looking at the info windows for various Apple Lossless files), it appears as though Mountain Lion no longer indexes the "codec" for Apple Lossless files, and therefore doesn't let you search by it. (Although I haven't tried this recently on at least Lion or Snow Leopard systems, I can verify that on OS X Leopard, which I still have running on an old machine, both the description "Apple Lossless" next to the codec field in the Info window came up, and it would also let you search by it.)
    I was just wondering if anyone else might have experienced this on their Mountain Lion systems? Thanks!

    I regret to inform this still has not been solved, though deleting the externalrecords helps purge those remnants away.

  • Codec for RAW in vista 64

    I am trying to find the codec for viewing RAW files in Windows Live Photo Gallery. I found the codec for Vista 32, but nothing for the 64 system.
    I may be in the wrong forum, if so can you direct me to the proper forum and/or give advice.
    Thanks....david

    I have been hodling off upgrading to CS4 for a year now, since Adobe has not make any statements about Windows 7 support.  If adobe has release some statements, can someone point me to the statement?
    http://www.adobe.com/products/creativesuite/faq/ See "Support for Windows 7"
    What is the possible release schedule for CS5, I am thinking May 2010?
    That's as good as anyone else's guess.
    CS: Sep 2003
    CS2: April 2005 (19 months)
    CS3: April 2007 (24 months)
    CS4: Oct 2008 (19 months)
    CS5:  May 2010 would be 19 months - but only Adobe knows the real date.

  • Codec for avi

    anyone know where to get the codec for quicktime to play & export avi's?

    Avi is a container that allows it to contain mutimedia content in various compression formats. QT already knows how to open or export avi files bur the default installation lacks the decompressors for many compression methods. These two sites have installers for codecs (COmpressors/DECompressors) that will play and export many but not all avi files in QT.
    www.divx.com
    www.3ivx.com
    Note that some people (at least in MacOS) have reported problems with QT 7 and the most recent codecs from those sites. There is no general problem with QT 6 in MacOS or WIndows and no one has noted problems for QT 7 in Windows but use at your own risk until more people comment on QT 7 and these formats.
    Also note that you need to purchase a QT Pro key ($30 US from an Apple Store) to export from the Player.

  • FCP IMX codec for windows

    Hi guys,
    is there any IMX codec for windows so i can easly export my grahics from my PC to FCP without rendering? CMIIW
    Many Thanks,
    Bayu

    Happy to help out, but you need to identify what cam or sequence settings you use to create the HD sequence.
    HD means so many things, including HDV and DVCProHD.
    What is it?
    And what did you choose to export to that create a smaller movie file for use on the PC?
    Because it seems you have converted the original footage to something else, otherwise the size would be the same.
    You might try an export to h.264 that should work if your friend is using v.7 of QT on Windows.

  • Where can I get codec for ISO files?

    Where can I get codec for ISO files?Premiere Elements

    An ISO is actually not a video file, it is a container... somewhat like a ZIP file that contains other files
    I do not know if it will PLAY what is inside an ISO, but I use Imgburn to write an ISO to DVD
    Read http://forums.adobe.com/thread/1322583 for notes on installing Imgburn WITHOUT any toolbar add-ons... Set Imgburn to use the slowest burn speed your drive and media will use... I set my burn speed to 1x and let Imgburn adjust to the actual minimum

  • Codec for .avi files

    Hey; this may be an easy or confusing question, unfortunately I don't have alot of time on my hands lately, but i'm looking to view an .avi file and quicktime says i need a codec to view it; i click the link, and theres several codecs, some free, some not, any idea what codec i need to view .avi files, is it free, certain site? thnx, [email protected]

    Microsoft, the inventor of the Audio Video Interleave format, no longer supports any of its uses.
    They write proprietary codecs for all of their software including most video formats.
    They've written their own version of codecs for the MPEG-4 format which also don't conform to the industry standards.
    AVI is a "bucket". You can fill a bucket with water, dirt or strawberries. But it's still just a bucket.
    Shame on Microsoft for even using the phrase AVI in any of its software.
    Apple invented the .mov container and still supports its use. It is also just a bucket as is its .mp4 file extension.
    At least .dv still means something that users can understand. And DivX is a bucket that wants to be a file extension. At least they know the difference.

  • 1080psf 23.976 capture codec for Arri?

    I need an update that includes a 1080psf 23.976 capture codec for Arri. 

    I am a working video assist on movie sets. I need the codec to capture a scratch track for playback purposes. The Arri outputs have a 1080p option, but the preferred codec of DIT's and camera operators is 1080psf. Video Assist is a job on movie sets that provides instant replay for Directors, Actors, Producers, Department Heads, Stunts, and Script Supervisors. DIT is the Digital Imaging Technition. The camera is cabled to a DIT who is cabled to the Video Assist. Simply put I need the codec to better perform my job, without having to spend $17,000 for Qtake software. Final Cut 7 has a psf codec, but Adobe Premier Pro is much nicer to operate.

Maybe you are looking for