Collector Configuration for Cisco LMS

Hi,
I have a cisco LMS 3.2 , what collectors need to be configured inorder to get the critical alarms such as HighBroadcast Rate in network

Device Fault Manager (DFM) is the module or application that would give you these kind of alerts;
a quick overview about DFM can be found here
first I recommend to install all available updates and patches for LMS;
after the initial discovery of LMS to get your devices into DCR you have to import device into DFM as described here
DFM is working with SNMP polling, thus you should get the events in the AAD (Alerts and Activities Display) if DFM has SNMP access to your devices;
Be aware, that DFM counts non-unicast packekts for the HighBroadcast Rate (broadcast and multicast packets; ifInNUcastPkts + ifOutNUcastPkts)
also read the user guide for DFM to get a general understanding of DFM

Similar Messages

Icmp Jitter collector configuration with Cisco LMS

Hi,
I am trying to collect jitter information of cisco Routers which are added in Cisco LMS
I have configured collector icmp jitter for them but somehow no stats are visible in lms and its says in IPM that u have no jitter collectors configured.
Do i need to enable anything on the Router as well to export stats to LMS ?
Thanks

Hi,
show ip sla application
IP Service Level Agreements
Version: Round Trip Time MIB 2.2.0, Infrastructure Engine-II
Time of last change in whole IP SLAs: *07:35:21.730 UTC Thu Mar 13 2014
Estimated system max number of entries: 27977
Estimated number of configurable operations: 27976
Number of Entries configured : 1
Number of active Entries : 1
Number of pending Entries : 0
Number of inactive Entries : 0
Supported Operation Types
Type of Operation to Perform: dhcp
Type of Operation to Perform: dns
Type of Operation to Perform: echo
Type of Operation to Perform: frameRelay
Type of Operation to Perform: ftp
Type of Operation to Perform: http
Type of Operation to Perform: icmpJitter
Type of Operation to Perform: jitter
Type of Operation to Perform: pathEcho
Type of Operation to Perform: pathJitter
Type of Operation to Perform: slm controller
Type of Operation to Perform: slm frame-relay interface
Type of Operation to Perform: slm frame-relay pvc
Type of Operation to Perform: slm interface
Type of Operation to Perform: tcpConnect
Type of Operation to Perform: udpEcho
Type of Operation to Perform: voip
IP SLAs low memory water mark: 38288719
The device is a Cisco 1841

Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

Hi All,
Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
Any help would be greatly appreciated.
Thanks in advance.
Samir

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router

Hi All,
We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
Any help would be appriciated.
Thanks in advance
Samir

Hi,
*** Device Details for d0151-100 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,HTTPS
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
This is the error while doing syn archieve.
I am not sure about Rtr7000 version but we have latest Rtr7000.
Waiting for your kind reply.
Samir

How we archieve configuration for Cisco ASA 5500 series appliances

Hi,
We need to archieve configuration for Cisco ASA 5500 series appliances.
We have Cisco works LMS 3.0.1.
Device package installed is 4.2
Any help would be appricated.
Thanks in advance.
Samir

Hi ,
Thanks for your answer.
Right now we are using TACAS to login in to the ASA. That means we need single username and password to login via
Cisoworks. Am I correct ?
Waiting for your reply.
thanks,
Samir

RAID Configurations for Cisco servers

Hi All,
What is the RAID configuration for Cisco Appliance(Version 8.5) like CUCM, CUPS, CUIC, Unity etc?RAID Configuration will be done while installtion itself or we need to do it explicitly?
Regards,
Adithya

Hi Geoff,
Thanks for the reply. Just wanted to know whether if this RAID configuartion is similar to the other server RAID where we install Cisco applications.(Like OS & Application Software is RAID 1 and Database is RAID10).
Regards,
Adithya

Cisco devices configuration for CW-LMS

Hello,
I am new to CiscoWorks LMS. I am working with a LMS 3.2 fresh installation. I added all the devices (routers, switches and 3 ASAs) into the DCR. Now I need to know how to configure the devices to send relevant info to the CW LMS machine. I am looking for something similar to this:
http://www.cisco.com/en/US/docs/solutions/Enterprise/Security/SAFE_RG/chap10.html#wp1056411
This is a deployment model for Cisco MARS, which shows what to configure on each device in the network to send the most relevant info (syslog, netflow) to the Cisco MARS.
Is there a best practice for CW LMS regarding this? For example, what syslog level should the routers send to the LMS?
Thank you!

There is a deployment guide whitepaper for LMS at http://www.cisco.com/en/US/products/sw/cscowork/ps2425/prod_white_papers_list.html . As for what to do syslog-wise, you should configure your logging facility to be local7 (this is the default on IOS, but not on ASA OS), and send at least sev 5 or higher messages. You may want to bump that up to sev 6 (informational), but sev 5 for IOS devices will be sufficient to get things like configuration change messages. For CatOS, you definitely want sev 6.

Optimal configuration for Cisco E3000 Router

Hi All,
Following are the details of my current home network setup, I would like to hear more recommendations and drawbacks of this setup.
ISP has provided with a Cisco DPC3825 DOCSIS 3.0 Gateway which has 4 Ethernet ports and a wireless networking but only 2.4 GHz.. This router is connected to the cable CPE box to internet. I have enabled the Firewall features of this router and disabled the Wireless network. This has also the DHCP server running.
The Second router is a Cisco E3000 which supports 2.4 GHz / GHz wireless networking. Connection to gateway is made via the 1st Ethernet port of gateway and then to the Internet port of E3000 router. I have connected my wireless devices to E3000 with GHz wifi lan. This router also has the firewall activated and DHCP server running as well.
Both routers have WEP2 Personal / AES security configured. Currently these two devices are on two different IP ranges ..etc gateway is 192.168.0.1 and e3000 is 192.168.1.1.
The E3000 is primarily configured for my online video for TV (Panasonic Vireacast). Please let me know if this is the best configuration or any other possible options.
Thanks,
RG

This configuration is called LAN to WAN configuration and this is the best configuration considering that you want to behave both the router as a router.
Because the other confiuration would be LAN to LAN then you can only use 1 router as a router and 2nd router as a switch.
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=529c188bc0ee4f7da79ffc22f2be33ec_4579.xml&pid=80&r...
The first configuration in the article is is LAN to LAN, scroll down the window for LAN to WAN configuration.

TACACS+ configuration for Cisco ASA

I tired configuring TACACS+ configuration for ASA but unable to complete it. I have ACS 3.3 for all other Cisco Routers and Switches

Leo,
I was looking around and come across this post. It's very late, however, wanted to add my inputs for other community members.
RSA Token/One-Time-Password support available with ASDM only in SINGLE ROUTED MODE. If you are in Single Routed Mode, you can do OTP with ASDM if you are running ASA 8.2+ with ASDM 6.2+.
If the firewall is running in multi-context and transparent mode. It won't work. Below is the enhancement request that was filed for the same feature to be supported.
CSCtf23419 ASDM OTP authentication support in multi-context and transparent modes
With WLC is yet not possible and there is a enhancement request filed.
CSCuf61598 WLC: Need ability to support multiple sessions via OTP authentication
~BR
Jatin Katyal
**Do rate helpful posts**

Configuration for Cisco SPA112

Anyone managed to configure SPA112 adaptor for incoming calls?
I have configured for outgoing and able to make calls but incomming just nothing.....
I have 1 channel and one number associated to the SIP account
Firewall ports 5060 - 5062 are allowed through
internal IP address has ports forwarded to it

I think you're the first one to post that the Cicso SPA 112 will work for outgoing calls. Would you be able to send me the configuration on how you accomplished this and what settings you used?
Do you use Skype out credits or simply dial from one Skype account to the other? I would assume you do not have a Skype-IN account??

LZW 4G LTE Router Configuration for Cisco 881W (Teleworker, VPN)

I can't get the configuration of the the router to allow traffic on my company's VPN. The router is connected to the internet and otherwise works fine but whenever I attempt to connect via Cisco AnyConnect or the Cisco router, I can connect but can't access any intranet resource, email, etc. In essence, I can authenticate but can't do anything.
I've tried contacting NetGear and they referred me to Verizon. I contact Verizon and Technical Support does not have any information about how to configure their own routers. I'm waiting to hear back from an escalation group in my company's technical support.
I tried opening ports for UDP/TCP already and I attempted to create a static route but the router tells me that my info in incorrect (but I have no idea what is wrong either).
Has anyone come across a similar situation or could help point me in a direction towards a solution?
Thansk.

Check with the network administrators for your company. They should be able to confirm the version of your Cisco AnyConnect VPN and the requirements that it needs to open and sustain a tunnel. Once you learn the requirements you can come back to the VZW forums for assistance on configuring your device.
Normally when a VPN authenticates but does not allow any communcation it means that there is a port, firewall rule or NAT feature conflict somewhere on the local network. For example, the old Cisco IPSec VPN requires UDP ports 500/4500, IP 50 and TCP 10000 to be open in addition to NAT-T enabled on the VPN server. Your company may have customized the VPN for thier enviornment so you really need the details before you can move forward.
A good link I like to save for instances like this (old Cisco VPN):
http://www.canvassystems.com/blog/articletype/articleview/articleid/14/how-to-fix-cisco-vpn-client-error-412.aspx

Cannot access configuration for cisco srp527w voice

I am trying to input my SIP configuration to the cisco srp527w voice set up but there is nothing there that I can input. All I can see is info, system, user 1 user 2. When I go to system, it ask for IVR user password...I tried using admin and cisco nothing change. Appreciate if some could help. thanks

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

SNMP Configuration for Cisco Unity

Dear All,
Can you please tell me how i can configure SNMP on my Cisco Unity.
Please help me.
Regards,
Malik.

Dear All,
Can you please tell me how i can configure SNMP on my Cisco Unity.
Please help me.
Regards,
Malik.

Collector Configuration for Sybase - history retention for DB growth

Hi Experts,
We need to modify the history retention in the DBA Cockpit for database growth. Could you specify which Data Collector is responsible for this data?
Thank you!
Best regards
Janos

Hi Experts,
We need to modify the history retention in the DBA Cockpit for database growth. Could you specify which Data Collector is responsible for this data?
Thank you!
Best regards
Janos

Cisco lms - config collection

Hi, i'm looking for a way to collect config's from specific devices periodically, is this possible?
for example, collect configs from firewalls everyday at midnight , and collect routers config once a week.
firewalls: (about 3 devices, config changes every day)
routers: (about 800 devices, rarely change the config)
the only config collection schedule i have found so far is too simple:
admin > collection settings > config > config collecion settings > periodic collection
second question, is it possible for cisco lms to send via e-mail the diff of the config pulled from devices? i mean the specific commands that have appeared in the new configuration file.
regards, ignacio

Unfortunately, LMS syslog mechanism is very minimalistic and doesn't have a lot of options to it.
However, the feature you're requesting is not very much LMS dependent. As, Ciscoworks depends on the kind of syslog message it receives from device, based on it, it captures some characters to send a notification as automated actions.
So usually it is the device which won't send a lot of information on what changes was done by which user in normal IOS syslog messages.
But, to certain extent, you can try to configure you device for Configuration-Change logger to receive details on what changes were made by users and check it on the syslog report, or configure AA on it for all or important devices.
You can enable a configuration logger to keep track of configuration changes made with the command-line interface (CLI). When you enter the logging enable configuration-change logger configuration command, the log records the session, the user, and the command that was entered to change the configuration. You can configure the size of the configuration log from 1 to 1000 entries (the default is 100). You can clear the log at any time by entering the no logging enable command followed by the logging enable command to disable and reenable logging.
Use the:
show archive log config {all | number [end-number] | user username [session number] number [end-number] | statistics} [provisioning] privileged EXEC command to display the complete configuration log or the log for specified parameters.
This example shows how to enable the configuration-change logger and to set the number of entries in the log to 500:
Switch(config)# archive
Switch(config-archive)# log config
Switch(config-archive-log-cfg)# logging enable
Switch(config-archive-log-cfg)# logging size 500
Switch(config-archive-log-cfg)# end
So, in all, it depends on the device and the kind of syslogs it send for LMS to react on it.
-Thanks
Vinod
**Encourage Contributors. RATE Them.**

Collector Configuration for Cisco LMS

Similar Messages

Maybe you are looking for