Color laserjet 2605dn changing paper type does not make the change at printer

I've had this printer for 2 years and have had this problem from time to time. This time I have not been able to find a cure. I'm running Win 7, 64 bit and the printer is on wired network.
When I change the paper type in the driver page to photo paper, the printer should slow the paper feed to allow for extra thickness. It doesn't, but I can change the speed by using the printer control panel to set it to photo paper (a bit of a pain since the printer is in a different room and it must be switched back to plain paper the same way when done).
I downloaded and installed the latest drivers (version 5.1.0.1), but this didn't help. The printer is still useable, but very inconvenient to use, so any help would be appreciated.
Thanks for any assistance you can provide.
Don

Look's like there are 3 different Universal print drivers (UPD) on the site. PCL6, PS and PCL5. I recommend testing the PCL5 driver if you haven't as yet. It is bizarre that this happens from time to time, but you cannot get it going again using teh same methods. Don't know if you have swapped out the network cable to see if that makes any difference. You can also try installing via USB to see if the problem continues in that type of connection, then run the network install again.
Is it critical that the unit slow down for this particular paper thickness? Have you noticed any print quality issues by leaving it unchanged?
Good luck.
Though I work for HP, My posts express MY opinion, and not those of HP.

Similar Messages

I have Firefox 5 now, in the admin section of my web site when I edit a change in the data it does not make the change on my data file. There was no problem in my previous version.

How can I return to a previous version that did not have problem? On Safari on my lap top Mac, I do not have this problem. We tried this on another Windows computer with a 3.5 or 3.6 Firefox version and there was no problem.

When you have a problem with one particular site, a good "first thing to try" is clearing your Firefox cache and deleting your saved cookies for the site. Note: this is likely to log you out, so finish up whatever you are working on first.
1. Clear Firefox's Cache
orange Firefox button ''or'' Tools menu > Options > Advanced
On the Network mini-tab > Offline Storage : "Clear Now"
2. If needed, delete the site's cookies here
While viewing a page on the site, right-click and choose View Page Info > Security > "View Cookies"
Then try reloading the page. Does that help?
Some sites appear to be incompatible with Firefox 5. The difficulty is tracking down the problem. To see whether it is caused by the new stricter HTML parser in Firefox 4+, you can turn that off. Please save any unfinished work first.
(1) In a new tab, type or paste '''about:config''' in the address bar and press Enter. Click the button promising to be careful.
(2) In the filter box, type or paste '''html5''' and pause while the list is filtered
(3) Double-click '''html5.parser.enable''' to toggle it to false (it should turn bold).
Then return to the problem page, reload and try again. Does that make any difference?
Here's the process to roll back if needed:
First, I recommend backing up your Firefox settings in case something goes wrong. See [https://support.mozilla.com/en-US/kb/Backing+up+your+information Backing up your information]. (You can copy your entire Firefox profile folder somewhere outside of the Mozilla folder.)
Next, download and save Firefox 3.6 to your desktop for future installation. http://www.mozilla.com/firefox/all-older
Close Firefox 5.
You could install Firefox 3.6 over it (many have reported success) or you could uninstall Firefox first. If you uninstall, do not remove your personal data and settings, just the program.
Unless you have installed an incompatible add-on, Firefox 3.6 should pick up where you left off. If there are serious issues, please post back with details.

I am having issues with adjusting the duration of time for each still frame and transition in imovie 11. Each time that I adjust these times, the app does not accept the change, and automatically enters its own time. Am I doing something wrong?

I am having issues with adjusting the duration of time for each still frame and transition in imovie 11. Each time that I adjust these times, the application does not accept the change, and instead automatically enters its own time. Is there a work around this? Or am I doing something wrong? Please Help!
Thank you,
lagrl

Have you tried turning off automatic transitions ? Choose file - project properties and follow the dialogue box to change duration with a slider. iMovie also doesn't allow a transition to be more than 50% duration of the clip its attached to. In other words if the clip is 4 seconds the transition cannot be more than 2 seconds and remember that relates to the first clip as the following clip (right side) is pulled back to overlay it.
Does this help. Perhaps you already know this ?

What does your account type does not support the view account feature mean?

What does your account type does not support the view account feature mean?

In reference to what? Where are you seeing this message - iTunes? Do you use a credit card for purchases in iTunes or do you download only free content?

My JSP file does not reflec the change of a Bean

My test environment: Win 2000, JDK 1.3.1, OC4J(standalone)
My problem:
In servlet, the change of a Strng value is reflected at the next refresh of a browser.
But, when a jsp file call a bean's getXXX(return a String value) method, and if the String value of that bean is changed, the next refresh or visit to that jsp file does not reflect the change of that bean.
For example:
1) TestClass.java
public class TestClass {
private String txt;
public class TestClass {
txt = "Test"; ----- (g
public String getTxt() {
return txt;
2) test.jsp
<html><body>
<h2>
<% TestClass test = new TestClass(); --(h
out.print(test.getTxt()); %> --(i
</h2>
</body></html>
In my first vistit to "http://localhost:8888/test.jsp" the brower shows "Test" String, but after I change the txt value to "Test1"((g) the brower does not reflect the change.
I found that if I use <jsp:useBean id="test" class="TestClass" /> instead of (h-(i line, the brower reflects the change of the bean.
Why does this occur?
Thaks in advance.
PS) In some cases(Not above example), I get the java.lang.ClassCastException.
So Each time I change a Servlet or a Bean, I restart OC4J.
null

SangKyu,
<jsp:useBean > has a property called scope, which defaults to "page".
So the bean gets reset everytime you reload the page.
Can I suggest that you set it to "session"?
The following syntax card I have found userful:
http://java.sun.com/products/jsp/syntax.pdf
Cheers,
Scott
Atlassian - Supporting YOUR 'Orion/OC4J' World
http://www.atlassian.com - [EMAIL][email protected][EMAIL]

I use itunes to store my music but I use Virtual DJ Broadcaster to play it. Somehow itunes has changed from Itunes Music Library to Itunes library. Virtual DJ does not Recognize the change.

I use itunes to store my music but I use Virtual DJ Broadcaster to play it. Somehow itunes has changed from Itunes Music Library to Itunes library. Virtual DJ does not Recognize the change. Virtual DJ at present seeing an older version of my libraries. Is it possible to Save my last library and Playlist and re-name everything else in my itunes account so it will again show "Itunes Music Library" Past libraries are of no consiquence . I'm hoping removing everything except the last Library on my computers will make Virtual DJ recognize it. I tried renameing the Library to "Itunes Music Library" but it did not work. I fear the problem is in the Registry and without the correct path I am reluctand to play around in there. Any help would be appreciated.

Incidentally, my first thought was to map a network share from the NAS to my computer, so that my music files appear on the Z: drive, say on my computer. I could then set up iTunes to store music etc in that folder, and to copy all new items to that folder. However, if I do that, all that'll happen is that on my NAS, the library file will become out of date as I add music to the collection but not to the index.

AddAnotherRow of Advanced Table, does not make the new row as current row

Hi OAF Gurus,
Requirement:
When user presses 'AddAnotherRow' button on OAAvancedTable, the new row that gets added should become the current row of the underlying VO of the table.
What’s happening:
When user presses 'AddAnotherRow' button on OAAvancedTable, the new row is not the current Row(VO’s previous current row retains its current status)
What I tried by far
APPROACH #1 - when create row
In VORowImpl - override create and set this new row as current
public void create(AttributeList attributeList)
try
super.create(attributeList);
// PSUDO CODE
am = this.getApplicationModule
vo = am.findViewObject("OAAdvancedTableVO1");
vo.setCurrentRow(this) // this should set the new row to current.
But VO's current row is still the old current row and not this new row.
APPROACH #2 - when insert Row
I thought that AddAnotherRow , internally must be doing a create() then an insert() row on the VO, so i overridden the insertRow(row) of the VO
public void insertRow(Row row)
super.insertRow(row);
this.setCurrentRow(row)
System.out.println("COMMENT insert called .............................................");
But this method is never called by the framework.
***Please help me make the newly created row on the OAAdvancedTable using 'AddAnotherRow' (out of the Box) , as the currentRow of the underlying VO***
Thanks
Chaitanya

Thanks a lot Chris.
I have used your code and it works perfect.
Now I am not using the out-of-the-box AddAnotherRow, as it does not make the newly added Row as 'currentRow' of the VO
I have used the following code by Chris and it solves the issue.
1. Determine the number of already displayed rows on the table
OAAdvancedTableBean tableBean = (OAAdvancedTableBean) webBean.findChildRecursive(tableID);
int rowsDisplayed = tableBean.getNumberOfRowsDisplayed();
replace tableID with the actual value.
2. I have the following routine to create the row and set it as the current row.
OAViewObject viewObject = (OAViewObject) findViewObject(viewObjectName);
int rowCountInRange = viewObject.getRowCountInRange();
Row row = viewObject.createRow();
int insertIndex = rowCountInRange;
if (rowCountInRange == rowsDisplayed) {
insertIndex = rowCountInRange - 1;
viewObject.insertRowAtRangeIndex(insertIndex, row);
viewObject.setCurrentRow(row);
Thanks again all of you for help
Regards
Chaitanya

Color LaserJet 2605dn reboots when attempting any report from LCD. Says Printing, then resets.

HP Color LaserJet 2605dn reboots itself when attempting any report from LCD. Says Printing, then resets with the green and amber light lit and the LCD screen says Hewlett-Packard. If I try to send a print job to it from a computer, it says printing, and resets just the same. I've upgraded the firmware to 20071108. I've rebooted the printer holding down the green and red buttons that didn't help. I also held down the two gray buttons and powered on which didn't help, it just cleared all my printing stats and cleared my configuration. I've attempted print jobs via USB, and network with same results. Admin webpage comes up. Thanks.

Hi Pahu,
Thanks for you reply. Here's some additional information because I'm not quite sure how to resolve the network addressing as you described. The router is set up as a DHCP server, using the standard 192.168.1.1 IP address, and the subnet mask is 255.255.255.0 The starting IP address is 192.168.1.100, and I have it set to allow up to 50 connections. (No particular reason, I think that may have been the default.) The printer is set up to check a variety of connection protocols, starting with DHCP. If that fails, it moves to BOOTP, etc. When I print the network configuraton page from the printer, it tells me the IP address is 169.254.18.32, subnet mask 255.255.0.0, default gateway 169.254.18.32, and the IP is configured by AUTOIP.
In the past, when it has been working properly, the printer shows an IP address of 192.168.1.10X, usually .100 or .101, but it depends on which device I've powered up first. This is what I would expect, given that the printer should be communicating with the router and be assigned an IP address by DHCP. What I can't figure out is why the printer reverts to its internal default IP address 169.254.18.32, and why this is inaccessible even if I try to designate the printer as an IP printer and type in the printer's IP address.
Do I need to set the printer to refresh its DHCP lease more often to ensure it doesn't get cut off by the router? How do I make sure the printer stays on the same subnet as the computers if they're all on the same router? Should I assign the printer a static IP address like 192.168.1.100, then set the DHCP range to start at 192.168.1.101? Sorry to ask so many questions, I'm not a network expert and I didn't think this printer would be such a pain to configure.
Cheers,
R

I want the feeder on top to pick up the paper and does not work. Brand new printer.

I have a new printer HP Office Pro 8610 and the paper on tope does not feed. It did for one or two times and stopped. I did not buy a warranty. I expected the printer to work. Please help.

The document here may help resolve issues with the ADF not feeding properly on your Officejet Pro 8620.
If the above does not resolve the issue - what country are you in? There is generally a one year warranty included for HP printers. You can check with HP's warranty tool here. In the US or Canada you could call HP at 1-800-HPINVENt, elsewhere see the contact information here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Button does not make the same thing in English and in German

Hi
I have created an HTMLDB-Application (HTMLDB 2.0) with two Pages:
Page1 has one Region in which there is one Report and two Buttons. Button1 has the Label 'German' and Button2 has the Label 'English'.
Page2 is a HTML-Page wich only gives a success-Message.
Page1: There is a Process1 wich is activated when Button1 is pressed. The Process sets the 'FSP_LANGUAGE_PREFERENCE' to German (de-ch) which is the Applications primary language. After that the Application branches to Page2
There is a Process2 wich is activated when Button2 is pressed. The Process sets the 'FSP_LANGUAGE_PREFERENCE' to English (en). After that the Application branches to Page2
When the Application has the FSP_LANGUAGE_PREFERENCE = de-ch and I tick the Button2 (English) the Application branches to Page2 and sets the FSP_LANGUAGE_PREFERENCE = en.
When the Application then has the FSP_LANGUAGE_PREFERENCE = en and i tick the Button2 (German) the application only reloads the page and it doesn't start the process and doesn't branch to page2. The same happens when FSP_LANGUAGE_PREFERNCE = en and I press the Button1 (English).
It seems that the Application can not see the processes and the branches when the FSP_LANGUAGE_PREFERENCE is en.
Does anyone have an Idea what could be the reason?
Thanks in advance.
Daniel
null

Hi Daniel
When I run your application, the language is set to en. Both the Englisch ENG and Deutsch buttons are javascript:redirect's to page 1, which as I understand it, will change the page in the browser as though you had typed in the address directly. It does not submit the page, and therefore the processes do not run.
When you run the page in german, what do the button links point to?
Have you made any changes to the german version, and not re-published the english version?
I'm not an HTML DB expert, so I hope what I've said is correct and it helps you.
Regards,
James

Acrobat X does not install the Adobe PDF printer

When I try to install the Acrobat X on a Vista SP2 machine, the installation completed successfully but it does not create the Adobe PDF icon in the printers section.
This was not a problem earlier, but there were some microsoft patches and GPO updates which happened which may be causing this issue. I am not sure what change has caused this problem.
Any ideas on where to start the investigation would help.

you need to update to 8.1

Changing Paper size does not change page break?

I am using Oracle Report R6i.
I have created a matrix report showing months horizontally and items vertically. By default, the report displays a vertical line (Page Break Line) at 8 inches (as shown in Ruler).
I change the paper size in Page Setup Menu but still the page break line displaying at 8 inches due to which only 03 months are displaying per page at Landscape mode. My page size is : 210x230 cm.
How can I extend that page break line so that atleast 6 months to be displayed per page.
Regards,
Luqman

Changing the size used by the printer with the page setup dialog does not affect how Reports formats the output. You need to change Reports page size for this.
In 6i, the page size for Reports is controlled by properties against the Section objects (header, main, trailer) in the navigator.
In 2.5 you would set the vertical and horizontal page size in the Reports property palette for all sections. With the introduction of individual sections in 6i, each section can have it's own page size.
In your example you probably want to change the page size against the "main section" to 13" x 8.26" to get the report to format in Landscape. Also remember to set the ORIENTATION parameter or property to "Landscape" so that the printer is set to Landscape as well.

ITunes does not save the changes I make.

Every time I start it it makes me go through the whole accepting the terms of agreement and reminds me that it can get album photo's for me. None of the changes I have made since I upgraded to latest version are saved and I am logged out of iTunes Store every time I close iTunes. I'm not sure if that is supposed to happen, but I doubt it is. Please help me, this is getting on my nerves.

Every time I start it it makes me go through the whole accepting the terms of agreement and reminds me that it can get album photo's for me. None of the changes I have made since I upgraded to latest version are saved and I am logged out of iTunes Store every time I close iTunes. I'm not sure if that is supposed to happen, but I doubt it is. Please help me, this is getting on my nerves.

ADF appl link to SQL database does not save the change

I use SQLJDBC 4 to connect to MS 2008 database. Then I create an simple ADF application with one model and business component that connect to one table. When I run the app. The grid and the detail come up nicely. I can insert new row and modified existing row without error with submit-commit operation. The grid updated with the change. But it did not update the database when I check the data from studio manager. Is there any configuration I am missing so the data are not updated.

Please give us your jdev version...
What exactly do you mean by submit-commit operation?
Have you run the application with jbo.debugoutput=console to see what its send to the server?
Timo

Photos not saved after sharpening and denoising-shows on screen correctly but when am trying to email it, does not reflect the changes?

I have tried to change pic's like sharpen and de-noise features, on screen ot shows all perfect, but when I try to email them, all the changes are lost, anyone can help with the same?
Thanks in advance.

Make sure you are viewing your image at 100%. At smaller views, pixels and layers and the way they interact are approximate interpolations and won't show you the actual pixel-for-pixel changes.

Color laserjet 2605dn changing paper type does not make the change at printer

Similar Messages

Maybe you are looking for