Color troubles printing to HP Color Laserjet 2600n

We are a school with a networked environment that includes about 40 Macbook Pros and 60 iMacs. Included in there are several eMacs and PCs. Over the past several weeks, our HP Color LaserJet 2600n printers have begun to exhibit printing where rather than the normal color printing, there appears to be added black toner on the print jobs. The PCs and eMacs are not exhibiting this problem at all, thus I eliminated the fuser possibility. I looked more at a potential driver issue.
These 2600n printers are shared out to the MBPs and iMacs via Workgroup Manager. They connect to these printers via Bonjour for printing. We do have an 802.11n wifi network with multiple SSIDs but no matter if it is cnonected over SSID or over wired gigabit ethernet, the problem still exists.
I tried printing via IP address, but the computers would not readily recognize the printers during setup, and when I manually selected the driver, the computers could not connect to the printer.
So, I am trying to figure out why all of a sudden these print jobs are exihibing severe color issues.

OK, I think I might have a solution. I have not tested it but I need to do a bit more research. What I have discovered is that it might be a Firmware issue. We found one that is still working fine and it actually has the older firmware numbered 20050610. The ones were are having the issues with are on firmware numbered 20070716.
I am going to see if I can revert the firmware... if I can find the older firmware!

Similar Messages

Printing on my HP Laserjet 2600n

HI, i have a new iMac which has been running tiger with my printer on a wireless network through an apple airport and it works fantastic, however i upgraded to leopard and have not been able to print a single document, even though the computers says it has completed the job, i have uninstalled the drivers, and used the driver on the setup from leopard, however the printer i use is not listed, so ive tried a few different ones, including the HP Laserjet 2605, but im still haveing the same problem, can anyone assist me as this is a major problem for me. I have looked thru the forums and have seen people with similar problems, but i cant find a way of combatting it. Any assistance would be really appreciated.

Here is a package I made that removes all the printers and installs the older HP software and drivers. Should work on 10.6.x through 10.7.1. I tested on 10.6.8 and 10.7.1 and seems to work fine.
Just beware it removes all printers, you will have to setup your other printers again. Read the contents of the package for info.
Also not when you go to seup the 2600n when picking the driver do not use the 1.3.0.261 driver, use the plain HP Color LaserJet 2600n driver. Version of the driver should be 1.3. Anything after seems to be a faulty driver.
Updated Links for new package…..updated wording in read me and fixed the script that runs to make a backup copy of the ppd folder found in /private/etc/cups/
http://www.mediafire.com/?wiyyt85b97xh6g5
http://dl.dropbox.com/u/18068810/HP2600n_Fix.zip

Printing problem with HP Laserjet 2600n

I recently bought a HP LaserJet 2600n and connected it to my router. It worked! I could print from it using my laptop. That was yesterday. Now for some reason it doesn't work. CUPS just says completed as soon as I send it. It can connect, because there are no error messages. Can someone help me fix this? I'm using the foo2zjs drivers from the AUR. I even made it print colour! I am really confused why this isn't working...
EDIT: Seems it works with Abiword...?? Yesterday it worked with my KDE4 apps and not Abiword. I'm confused!
Last edited by miggols99 (2008-03-02 19:57:34)

The page looks perfect in preview and as a PDF. I can't print from the PDF, however, because it shrinks the text and expands the margins ...
Something's fishy. Save as PDF should result a file that looks exactly, precisely, like what you'd get if you printed directly to your printer.
I suspect your Word document has been corrupted by a few bytes of random data that is causing your printer to go nuts. Try cutting that portion out of the document, and pasting it in a new blank document so you can incrementally isolate the damage.
This isn't going to be as easy as it sounds, because when the PostScript printer driver encounters the errant code in the Word document, it's essentially telling the printer "now, go to the top of this page, print a nasty black smudge, and then crash." You might have to cut a whole page before and after the suspected corruption. If you're lucky you might be able to cut the portion then paste it right back as "unformatted text". Try that.
BDAqua wrote:
I'm not familiar with Word,
We should all be so fortunate. Word does use the standard OS X Print dialog though.

Export color vs. print to file color issue with 2.3RC

Hi,
I'm having problems with exporting photos for web-site usage.
In short: colors get extremely washed out and plain when using "export to disk" (requesting sRGB color profile, in jpg-format). But, when "printing to file" using sRGB profile and rendering intent perceptual colors are reasonably close to what I see in LR. Yes, I know, sRGB is limited, but...
Why there is such a difference when both methods are using sRGB for generated jpg? Is it the fact that rendering intent can not be selected for "export to disk"?
As I can not control pixel dimensions in Print mode is not an option for my use (and I can not control sharpening with plug-in, but the color issue is there to begin with without any export plugin intervention).
In contrast, LR 1.4 export to disk gives reasonable colors, the color issue has appeared with 2.x series.
Running Windows XP SP3, LR 2.3RC, display calibrated with Color Vision SPyder 2.
Please help, this is driving me nuts :(

I think, that your examples shows the same problem as my observations.
It seems that your display has even smaller gamut than sRGB (on my notebook DELL D620 this is also the case) so after you calibrated it, both lightroom and color managed firefox shows more saturated colors than windows explorer showing exported image (as far as I know, export from library module works correctly, but win explorer is not doing conversion to your monitor profile, that's why image is undersaturated). This is correct. It is really hard to calibrate such a low quality display, which can often be found on cheap notebooks - I have my own experience with it. Blue shades are really weak so heavy corrections have to be done in the profile (generated with spyder in your case), which can result in purple skies (why? Read this: http://www.brucelindbloom.com/index.html?WorkingSpaceInfo.html).
Problem is with image printed to file. This should look same as file exported from library module given that you use sRGB both as a destination space in export from library and as a printer profile while printing to file. In your case LR printed your image using values corresponding to your monitor profile (even if sRGB was selected) which resulted in oversaturated image (because your display has smaller gamut than sRGB). In my case images printed to file are undersaturated (because my monitor has gamut wider than sRGB). But I'm sure this is a bug! Your monitor profile should not affect printing to file in any case if sRGB is selected as printer profile!
Summary: purle sky in LR and in color managed FF is ok, but purple sky in image printed to file is not ok. :-)
And my hint: do not try to calibrate this display... :-)
You can try to make some measurements of your UNCALIBRATED NB display using this freeware: http://www.homecinema-fr.com/colorimetre/index_en.php You will probably see a very uneven color temperature across grayscale and much smaller gamut than sRGB.
Let us know your findings.

HP Color LaserJet 2600n and HP IP Printing

I was having trouble configuring my HP Color LaserJet 2600n for HP IP Printing. The following steps resovled the problem. Perhaps others may find this useful.
I just purchased an HP Color LaserJet 2600n printer at CompUSA. I was able to successfully connect it to my network and print using Bonjour Printing (from all of my various iMac, iBook, PowerBook and MacBook computers), but was not able to configure it for TCP/IP printing. To solve the problem,
1. I visited the HP website and downloaded new firmware for the printer:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us &prodNameId=446154&prodTypeId=18972&prodSeriesId=446153&swLang=8&taskId=135&swEn vOID=219
There are 3 files there, I downloaded and installed all of them in the following order:
2. HP Color LaserJet 2600n Printer Firmware Update Utility - for some reason, the firmware on my new printer was from 2005 even though HP had posted new firmware as late as Dec 2006.
3. HP color LaserJet 2600n DC controller firmware update utility - a firmware update that addresses a ghost-image issue.
4. HP Color LaserJet 2600n OS X Universal Binary Full Software Solution - an updated set of drivers.
After all firmware and software was successfully updated....
5. I opened /Applications/Utilities/Printer Setup Utility.app and click the "Default Browser" button at the top of the page.
6. Clicked the "More Printers..." button at the bottom of the page.
7. Set the popup at the top of the configuation pane to "HP IP Printing" and clicked the "Manual" button immediately below it.
8. Entered the local network address for my printer (xxx.xxx.xxx.xxx) and clicked the "Connect" button. The rest of the information in the panel was automatically filled in for me.
9. Clicked the "Add" button. The printer was added to the list of available printers in the Printer List, although the name of the printer is set to the ID that is configured in the printer firmware.
10. Select the new printer (NPIA0853X in my case) and click the "Show Info" button in the Printer List toolbar. Move the popup on the dialog to "Name and Location" and enter an new name (e.g., "HP Color LaserJet 2600n").

Download and run this on the XP machine. I suspect a security system update or change, but let's let the utility tell us.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

HP Color LaserJet 2600n quit printing on an XP machine

Even though my HP Color LaserJet 2600n shows "ready" on my XP control panel screen for printers, it just quit communicating with my XP system. I have it connected via an Apple Time Machine and found it easy to connect to the printer from any computer in the house (desktops, laptop, netbook, Apple). It worked fine for a long time but now I can't get my XP system to connect to the 2600n. Anyone have a suggestion on what I should do to regain the ability to print to this printer from my XP desktop? Thanks in advance.
PS - Although I know this sounds wrong, I didn't install any new software or make any other changes to my system. It was printing fine yesterday and today - nothing! I've rebooted the PC and the printer. There are no error messages on the printer - it simply says "Ready". What am I missing?

Download and run this on the XP machine. I suspect a security system update or change, but let's let the utility tell us.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Unable to print to an HP Color LaserJet 2600n in 10.4.11

Hi (I really, truly have gone through the other topics and can't find a solution).
I'm trying to print on a G3 iMac via USB to an HP Color Laserjet 2600n. The printer driver is not included with Apple, and when I went to download it from the HP site (complete package for G3 computers running OS 10.3 or 10.4) it says there are no files to mount. I downloaded the same thing for a G3 running Panther and it installed perfectly and that iMac prints to the 2600n without a problem. I then downloaded the driver for G4s using the 2600n onto the G3 running 10.4.11 and while it installed fine and the print setup recognizes the printer, the printer will not print. It goes through "starting job" gets to "processing job" and stays there forever. I was on Customer Support with HP, and as a result of installing the printer on my older iMac, we've deduced the problem must be with the software on the G3 that won't print (the one running 10.4.11)
I read somewhere that with this HP printer and some others the job gets processed on the computer itself and then is sent to the printer. Clearly, the iMac is not processing the job.
I've installed, uninstalled, reinstalled, redownloaded, etc. etc. I don't know what to do. I installed Ghostscript et al, but there is no driver there for the 2600n. I've tried generic postcript and it doesn't work- in that case the print box goes for a few seconds and then says "printing stopped."
It's only this printer- this iMac with 10.4.11 prints to two other printers via a Bonjour network (an HP 2015 and an HP 2300n). But I'd like access to a color printer. Any thoughts? Any ideas? Why won't the complete G3 package install on this iMac when it will on the one running Panther? And why won't it process the print job?

I'm trying to print on a G3 iMac via USB to an HP Color Laserjet 2600n. The printer driver is not included with Apple, and when I went to download it from the HP site (complete package for G3 computers running OS 10.3 or 10.4) it says there are no files to mount. I downloaded the same thing for a G3 running Panther and it installed perfectly and that iMac prints to the 2600n without a problem. I then downloaded the driver for G4s using the 2600n onto the G3 running 10.4.11 and while it installed fine and the print setup recognizes the printer, the printer will not print.
OK. So you began by trying to install the same package you installed on the Panther machine? It sounds as though the file got corrupted during the download if the system couldn't mount the disk image. Anyway, you then downloaded a different package for G4 machines and installed that on your G3 machine but this didn't work.
Are you sure about this? Do HP really have different packages for G4 and G3 Macs? If so, you will need the G3 package for a G3 Mac. Can you point me to the HP download page listing the drivers so I can take a look? That way I should be able to see exactly what you've tried so far.
OK, I found the page. There isn't a G4 package as such but the G3 one is supposed to run on Tiger so that is likely the one you need.
Is the printer's firmware up to date? I notice there's an update utility for it, too.
It goes through "starting job" gets to "processing job" and stays there forever. I was on Customer Support with HP, and as a result of installing the printer on my older iMac, we've deduced the problem must be with the software on the G3 that won't print (the one running 10.4.11)
This doesn't follow. It could be that HP's drivers don't work properly on Tiger but do on Panther. That could as easily be HP's fault as anybody else's. (It might not be their fault, but the fact that their driver works on Panther doesn't necessarily mean that driver - or another driver - will work on Tiger.)
I've installed, uninstalled, reinstalled, redownloaded, etc. etc. I don't know what to do.
When you uninstalled, how exactly did you remove the installation? Please give me as many details as you can.
I installed Ghostscript et al, but there is no driver there for the 2600n.
Why did you think installing GS might help? Ghostscript doesn't provide print drivers as far as I know (though it is involved - or can be involved - in printing processes).
- cfr

Unable to network print to HP Color LaserJet 2600n connected to Windows PC

I just got a new MacBook Pro and I am trying to print on my network to a HP Color LaserJet 2600n that is connected and shared on a Windows PC. I have carefully followed the instruction posted on http://www.ifelix.co.uk/tech/3015.html and I am still unable to print. I made sure the printer name on the remote PC has no spaces. After I enter (on my Mac) my user name and password to access the user account on the remote Windows PC, I get the following error message:
Unable to connect to server with the provided password and user name. Error: 256
Please help! Thank you!
MacBook Pro Mac OS X (10.4.8)
MacBook Pro Mac OS X (10.4.8)
MacBook Pro Mac OS X (10.4.8)
MacBook Pro Mac OS X (10.4.8)

The Windows PC is running the Windows XP Firewall, the Avast Antivirus, and Windows Defender. I have deactivated all these applications and the issue persists.
I called Apple today (I am still in my 90-day free support since this is a new MacBook Pro). After some basic troubleshooting with a tier one rep, I was transfered to a tier 2 rep who told me after making sure that I was following the right steps to try to add the printer, that since the HP LaserJet 2600n printer is connected to a Windows XP computer, my set-up is not supported by Apple and declined continuing troubleshooting the issue. According to this person Apple will only support network printing when the printer is directly attached to a hub/router.

Hp color laserjet 2600n, very dim grayish film when printing black only

For some reason, my hp color laserjet 2600n has started printing with a very dim grayish film over each page. I've had this printer for about a year, and it didn't do this at first. Does it no matter what program I print from. I'm sure it's a setting issue, but haven't been able to figure it out. Any ideas?
And, when I select to print in black only, it still prints the color on web pages. Is there a way to print from only the black cartridge? These are the options in the printer dialogue box under color: print in grayscale, black only, 4-color. Under these settings are other options, edge control, half-tone and RGB color. I've tried each setting individually and still the gray film. The only other possibility I can see is under Print Options, it has draft quality or image quality. I've tried both and still the film.
Have any ideas.

1. take out all of the ink cartriges and look at the big black roller on the door for streaking, if streaking, clean with a lint free cloth dampened with windex (window cleaner) then close the door.
2. let it run to initializing.
3. open the door and look and the black roller on the door to see if you have streaking. If no streaking put one cartridge in and close the door and repeat the steps until you find what cartridge is causing the problem.
I did this and found that my cyan was creating the lines on my paper. I cleaned the cyan roller with a Qtip and some rubbing alcohol and it works fine now, no more lines on the paper.
Cheers

HP Color Laserjet 2600n cant print on Win8 even with the right driver installed!

I configured the HP Color Laserjet 2600n from TCP/IP port and dit the windows update on drives, installed my printer but it won't even print the test page. it says error printing on the print queue. I cheked the network and sharing. I checked the printer works perfectly on Win 7 but not on my hp Win8.

Hello there,
To get your issue more exposure, I would suggest posting it in the commercial forums since your product is a commercial product. You can do this at Commercial Forums - Printers - LaserJet.
Enjoy your day!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Networking a HP color laserjet 2600n printer on windows 7 (64-bit)?

Hello,
Have an HP Color Laserjet 2600n printer and are running Microsoft Windows 7 (64-bit). I installed >> HP Color LaserJet 2600n Plug and Play Package off of HP website [ http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=446154&p... ]. The drivers work fine if you connect via USB port but unfortunately there's no way to connect via network. Can anyone give me guidance on how to connect the 2006n via a network on windows 7 (64-bit)?
Thanks
This question was solved.
View Solution.

Have you plugged the printer into your router and does it have a proper IP address? If so:
1. Make sure the printer is turned on and connected to your network. Verify that you can access the printer's internal web page by browsing to its IP address before continuing.
2. Click >> Start >> Control panel >> Printers.
3. Click the Add a printer
4. Select Local printer
5. Select Create a new port and select Standard TCP/IP Port and click Next button.
6. Under Device type, select TCP/IP Device. Under Hostname or IP address, enter the printer's IP address. Click Next.
7. Select Hewlett-Packard from the list of manufacturers and select and select your printer model. Click Next.
If your printer model was not listed, then select Have Disk, browse the HP CD that came with your printer and select the first file that starts with hp and ends with inf. Click Open then OK. Select your printer model. Click Next.
8. If you are asked, use the currently installed driver.
9. It will ask for the Printer name -- enter a new name or use the existing one. This will be the name of the printer that you select from other applications.
10. You may be asked to share the printer. Choose NO.
11. The Print Test Page box appears. Go ahead and print it.
12. Click Finish.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Color Laserjet 2600n: only red not printing properly, washed out on the left side

Hello,
Our HP2600 Color Laser printer does not print well whatever includes the color red. On a portrait layout the 2" from the left are washed out in red. We only use new HP cartridges, clean the machine regularly.
Error happens with different computers, XP and OS 10.
Machine is about 2.5 years old, estimated 100,000 pages have been printed on it.
Thanks
Su

I have two 2600n color laserjet printers.
One has color fading down the left hand side and I understand that this is due to dust accumulating on mirrors and laser.
More worrying is that the second printer will not print the color red at all - it gives an orange output

E51 print with an hp color laserjet 2600n

Hi
I have a nokia e51, it can connect to my wi-fi but I have a problem with my Hp color laserjet 2600n. I try to create a unix print server on my pc that running windows xp, but it doesn't work. In particular the print receive the document in its queue bun doesn't start. I try a direct connection using the socket bearing but this attempt fail too.
Thank You for help.

Hi
I have a nokia e51, it can connect to my wi-fi but I have a problem with my Hp color laserjet 2600n. I try to create a unix print server on my pc that running windows xp, but it doesn't work. In particular the print receive the document in its queue bun doesn't start. I try a direct connection using the socket bearing but this attempt fail too.
Thank You for help.

Why does IE 9 say internal error and cannot print to Color Laserjet 2600n?

IE 9 displays message "Internal error, cannot print page" when I try to print to a networked Color Laserjet 2600n. Printing works well on my other networked HP printer.

The windows 8 driver for this printer should be available in late January. Please bookmark this site and visit it for up to date information. Also located on this site are links to documents for the network workaround and the in-os document.
Laserjet Printers supported in Windows 8
Install HP print software via a network in Windows 8
As a test, I did install this using the windows 7 drivers, it printed fine but I received a pop up giving me an error printing but it still printed. I then used the network work around to shut the bi-di off and the pop up went away, again it printed fine. I would suggest if you use the windows 7 drivers, that you upgrade to the windows 8 drivers when they are available.
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Color LaserJet 2600n printing 2 green horizontal lines

Have a Color LaserJet 2600n printing 2 green horizontal lines on each printed copy.

Hi.
Can you measure the distance in millimeters between the two lines and post a reply back?
Kazman
I am an HP Employee
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Color troubles printing to HP Color Laserjet 2600n

Similar Messages

Maybe you are looking for