Command to erase configuration on AP Aironet
Usually in cisco the comand to erase configuration is
wr erase
I need to wipe an AP but by console session. That comand is not working what is the command that will erase the configuration?
Usually in cisco the comand to erase configuration is wr erase
If you have static IP address, "wr erase" is not enough as the IP Address will still remain.
The command "wr default" will erase the config of an autonomous IOS including static IP address.
I need to wipe all info before I send it back fotr warranty
I wouldn't worry about that. Cisco won't "glean" off your configs.
Similar Messages
-
What is Login command in VTY configuration
Pls information in usage of Login command in VTY configuration in brief
Hi,
Login is used to control VTY access, it generally has 4 cases when AAA is not configured, and with AAA it serves another purpose:
Without AAA:
One of the following methods must be explicitly configure otherwise there can't be VTY access to the router.
1. "no login" > No password is required for VTY access
2. "login" + "password xxxx" > This password is required for login.
3. "login local" + "username xxxx password xxxx" (global configuration) > a local configured username and password are required for login.
4. "login tacacs" + "tacacs-server host x.x.x.x" (global configuration) > Use TACACS or Extended TACACS server for login.
With AAA:
With AAA it can be used to specify a custom AAA authentication method using the "login authentication xxxx" command under the VTYs.
NOTE TACACS+ can be enabled only through AAA commands.
I hope that i've been informative.
BR,
Mohammed Mahmoud. -
How to copy and paste the text in Russian - 'command+c' erases it
How to copy and paste the text in Russian - 'command+c' erases it
I want to publish a book with Blurb. They don't have Russian fonts, so I have to type the text in Russian in Notes in my iPad, send it to my e-mail box, and then open the e-mail box in Mac, and copy and paste the text into the book template of Blurbs. I don't know how to make a Russian keyboard in Mac to be able to type quickly. I asked about it in the Apple store, and they showed me how to find a Russian keyboard in the net, but it takes much time to type using a screen keyboard, and the texts also cannot be copied and pasted, when they are in Russian. They are erased when I press 'command+C", and all I have is a single letter 'c' instead. No problems with texts in English. Maybe Russian is not supported for copying and pasting?:(
-
Erasing configuration on the IP phone remotely
Guys,
is there any way to erase configuration on the IP phone CP-79XX remotely - through device web page ?
MladenOne way is to use Berbee's Remote control software. We use it and it works pretty well.
http://www.berbee.com/public/berbeesoftware/Remote.aspx -
Full backup and upgraded my properly working Xserver 10.6.8 to Mavericks 10.9.1.
Web service running fine, File Service running fine.
Mail service: I can't send mail through my Mavericks Server.
(i think my mail.lukedesign.com is "offline")
What am I missing ? I can no longer send mail after the upgrade !
Helo command rejected: Server configuration
error (in reply to RCPT TO command)
Reporting-MTA: dns
X-Outbound-Mail-Relay-Queue-ID: 930307000008E
X-Outbound-Mail-Relay-Sender: rfc822;
Arrival-Date: Sat, 28 Dec 2013 17:48:36 -0500 (EST)
Action: failed
Status: 4.3.5
Remote-MTA: dns
Diagnostic-Code: smtp; 451 4.3.5 >: Helo command rejected:
Server configuration error
bh=LIrD+hJmwz+5MZLs4vaxCpbJMUJarfXJSIlQFwtzPV4=;
h=From:To:Subject:Message-Id:Date:MIME-Version:Content-Type;
b=aqJBFaESW7MinKgXTlokj6WU0UxrmNYjYsXhcedpJr1io9uJ82XuN+FjKF0SLtebQ
DhEIuYEEVU6sKsyh/y9+jKUtK2GCHexaXhWouA++9+FvT2NdqczDTdMEd/Q8kHdUOO
Vre27uIG4VlMMlFW9CScIt9ZL3qsH+xR3oKlT7JM=
x-aol-sid: 3039ac1af95452bf554450bb
<Email Edited by Host>Postfix Debugging Howto
-
Need Terminal Command to Erase External HD
I used the Disk Utility to partition an external Western Digital hard drive with one
partition for the Time Machine and the other for SuperDuper. Something happened
when the Disk Utility made the partitions. Now the two empty partitions show up
on the desktop but the Disk Utility cannot do anything. I suspect the directory is
hosed. The DU cannot Repair or even Erase the external drive. The DU hangs (does
not respond) and I have to use Force Quit. FYI, DU fails when it tried to unmount
the partitions.
I am not very skilled in terminal commands and would appreciate some specific
commands to Erase the external WD hard drive. When I open the terminal it has
me at the user level. What is the command to view the external drive, then what
command is needed to ERASE it. Once erased I think the Disk Utility should be
able to do its thing.
All of this needed to create a Time Machine backup driveaRKay wrote:
Select the top line for the drive in DU's sidebar, click the Partition tab, then
use the Current pop-up menu to select 1 Partition, and click Options and select GUID.
I tired that before making the posting. When I click on partition, it cannot unmount
either partition and DU hangs (does not respond).
Try booting up from your Install disc and using it's copy of Disk Utility. (Boot from the disc, select your language, then on the next screen select Utilities in the Menubar, then +Disk Utility).+
I would like to jump start the drive from the terminal if possible.
II'm not well-versed in UNIX. You might get some help with that in the UNIX forum, in the +Mac OSX Technologies+ forum, at: http://discussions.apple.com/forum.jspa?forumID=735
Maybe I need a 3rd party utility to fix what DU hosed? Again, I suspect the director his hosed.
+Disk Warrior+ is thought by many to be the "gold standard" of such apps, and as probably a good investment, but is about $100. Whether it can fix this, I have no idea. -
How to enter into interface configuration mode on aironet 1130AG
How can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?
When I put following commands in enable
conf t
interface Dot11Radio1
but, it fails and I cannot enter into "interface configuration".
How can I do this ?
The reason why I enter into
conf t
interface Dot11Radio1
because I want to disable cdp via CLI ( serial console).
best regardsGeorge,
I ran into an exception the other day – lightweight 3500s (and presumably 3600s) are allowing config t without the debug precursor. The lab version I’m doing this on is 7.0.220.0. Do you have same/different results? I’m not sure if this is tied to the AP model or the lw code they’re running. I’ll need to do some more testing.
Justin -
Key Commands corrupt using Configurator in Photoshop CS5
For me, when the Configurator Panel is open common keyboard commands for tools such as the brush or patch tool (any of them) no longer work. There is a brief pause, it switches to the tool you want, and then it reverts back to the tool you were using. Holding the key down will keep it visible, but let go and it reverts back to the tool you were using.
This totally sucks as I've grown quite fond of Configurator. It's a real time saver. Too bad they didn't incorporate a customizable tool panel right into Photoshop...
But at any rate, something seriously wrong here and I can no longer use Configurator 2.0. Hopefully there will be an update...but I won't hold my breath.
Suggestions welcome...I did create a panel from scratch just to see if that would fix things up. It didn't. I tried a panel without any keyboard commands on it (since that is what is effected) and that didn't do anything either.
LanceI'm having exactly the same problem as Lance with the Configurator V2 Panels. It's very frustrating and I've only just worked out that it's the Configurator Panel causing the problem.
It seems a bit intermittent but closing the panel fixes it instantly.
Dave -
What is Operating System commands in Adapter Configuration??
Hi Frnds,
When we will use Operating system commands Option in Adapter Configuration??
Regards,
RajHi,
Go through this blogs..
/people/michal.krawczyk2/blog/2005/08/17/xi-operation-system-command--error-catching
/people/sameer.shadab/blog/2005/09/21/executing-unix-shell-script-using-operating-system-command-in-xi
When we will use Operating system commands Option in Adapter Configuration??
http://help.sap.com/saphelp_nw04/helpdata/en/0d/00453c91f37151e10000000a11402f/content.htm
Go through this link some experts discussions:
Run Operating System Commands
How to run Operating system command in receiver JDBC Adapter
Hope this info is useful to you..
Thanks,
Satya Kumar.. -
Toshiba VAP - Button Support - command line options configuration
Hi,
I need to configure Button Support Drivers for Portege Series Laptops as part of deploying Windows 7 x 64 bit Enterprise on the following models: Z830, Z930 and R930.
I need to install Toshiba Value Added Package with only Flash Card option.
What command line options are present to do this?
I am looking to deploy this via SCCM.
Thanks,That is a way to approach setup.exe in general, but the great Toshiba VAP doesn't provide you with such options that you can call out.
I have tried several methods, but there seems to be no way to install Button Support / Flash Cards alone. I can not believe no one has installed TVAP in an enterprise?
In an enterprise environment, you wouldn't necessarily give users access to encryption and password utilities, specific to laptop models. However, you need the app so the button support at least works, instead of providing the customer with a Laptop having non functional buttons!!
Is there any thread that points to or can Toshiba support help enterprise customers to deploy TVAP?
I have less hope, with the experience I have had with this app. -
Will command R erase everything?
The repair disk utility is asking me to do Command R. Will this erase everything on my machine. I have also been unable to use TIme Machine. So I don't have a backup.
Get another disk drive and use either CCC or SuperDuper to create a bootable clone of the disk drive.
Boot from the clone to be sure that it was created properly.
Once you can boot from clone, reformat the internal disk drive and then copy the clone back.
Reboot from internal disk drive. -
Configuration of 2 Aironet 1310 in a Bridge
I have 2 Cisco Airnet 1310 ( outside ) Wireless access-point/Bridges. What I need is the easies way to set these up in a Bridge configuration ( With each other. WE have a remote building that is Cost Prohibitive to run Fiber cable to. I run several Vlan's on my network and the remote building will need to access 3 of the vlans. So I need these Wireless bridges to trunk the link between them. I also need the highest encryption on the Wireless that the 1310 can handle.
Any suggestionsYou can trunk up to 16 VLANs between two 1310 bridges.
Configure one bridge as root-bridge, the other as non-root.
The "wireless" trunk is configured with a single SSID.
The management IPs of the bridges must be in the native VLAN.
For a simple PtP link I'd suggest using WPA-PSK for key management
with AES-CCMP encryption and a random string as PSK.
Using AES-CCMP doesn't support concatenation. If you need the
additional performance from concatenation use TKIP for encryption.
With the latest IOS version, all this can be configured from the GUI.
Below are the relevant parts for the CLI configuration of the root-bridge
(VLANS 101-103, 999 native)
dot11 ssid BRIDGE-SSID
vlan 999
authentication open
authentication key-management wpa
infrastructure-ssid
wpa-psk hex C0B3F98C9C33B75C298AEFAF865290BE7DDD15D563B0DAF644CC41EFC74CA29A
interface Dot11Radio0
encryption vlan 999 mode ciphers aes-ccm
ssid BRIDGE-SSID
station-role root
interface Dot11Radio0.101
encapsulation dot1Q 101
no ip route-cache
bridge-group 101
bridge-group 101 spanning-disabled
interface Dot11Radio0.102
encapsulation dot1Q 102
no ip route-cache
bridge-group 102
bridge-group 102 spanning-disabled
interface Dot11Radio0.103
encapsulation dot1Q 103
no ip route-cache
bridge-group 103
bridge-group 103 spanning-disabled
interface Dot11Radio0.999
encapsulation dot1Q 999 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
interface FastEthernet0.101
encapsulation dot1Q 101
no ip route-cache
bridge-group 101
bridge-group 101 spanning-disabled
nterface FastEthernet0.102
encapsulation dot1Q 102
no ip route-cache
bridge-group 102
bridge-group 102 spanning-disabled
interface FastEthernet0.103
encapsulation dot1Q 103
no ip route-cache
bridge-group 103
bridge-group 103 spanning-disabled
interface FastEthernet0.999
encapsulation dot1Q 999 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 172.17.172.17 255.255.255.248 -
Reg : OS commands in Adapter Configuration
Hi,
I have seen the option like <b>Run Operating Sustem Command Before Message processing and After Message</b>.
How can I use them
Where can I see the results of it.
I need an OS command to diplay all the files in a directory before message processing .
How can I use it.
Regards,
Kalpana.Hi,
Please Follow these
Run Operating System Command Before/After Message Processing -
http://help.sap.com/saphelp_nw04/helpdata/en/bc/bb79d6061007419a081e58cbeaaf28/content.htm
Also to catch errors - /people/michal.krawczyk2/blog/2005/08/17/xi-operation-system-command--error-catching
Reward points if Helpful
Regards
Sesha -
Hi Surendra,
I was just given this task to see how i can configure a second ssid for guest access in our environment.
this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time.
My AP config is attached below.
Please tell me what am I doing wrong.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan?
Does the access point need to be aware of the voice vlan?
Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
I will greatly appreciate your urgent response.
Thanks in advanced.Hi,
As far as i know we dont set the ip helper address on the radio interface. It should be on the L3 interface of corresposding VLANs i.e.
int vlan 20
ip helper-address 192.168.33.xxx
int vlan 60
ip helper-address 130.20.1.xxx
I'm assuming that your using SVI's (int Vlan 20 and int Vlan 60) rahter than physical interfaces. Also hope you have configured switch port as trunk where this AP is connected.
Modify the AP config as below since you are using data vlan as the native vlan
interface Dot11Radio0.20
encapsulation dot1Q 20 native
interface FastEthernet0.20
encapsulation dot1Q 20 native
Ideally your AP fastethernet configuration should looks like below and not sure how you missed this as this comes by default when you have multiple vlans for multiple ssids.
interface FastEthernet0.20
encapsulation dot1Q 20 native
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface FastEthernet0.60
encapsulation dot1Q 60
no ip route-cache
bridge-group 60
no bridge-group 60 source-learning
bridge-group 60 spanning-disabled
Hope this helps.
Regards
Najaf -
Configuration of cisco aironet 1260 series access point..??
i hv a cisco aironet 1262n access point and a normal router(without wlan) with a broadband connection
now i want to use my access point as a wifi hotspot
but i am not able to access it, through web browser
i dont know how i connect wires so that i am able to access " AP access page" and also i forgot its IP address too so can u pls tell me how do i reset it to defaultYour AP is most likely loaded with a controller-based IOS. You can easily convert this to autonomous IOS.
Read this: Using a TFTP Server to Return to a Previous Release
Maybe you are looking for
-
Help needed in business logic implmentation in oracle sql.
I got a requirement from customer that i need to generated numbers based on first value which is entered by users but not second values.. for example: c1 c2 1 1 2 1 3 1 4 1 1 2 2 2 3 2 4 2 1 3 2 3 3 3 4 3 1 4 2 4 3 4 4 4 1 5 2 5 3 5 4 5 unlimited.. t
-
ITunes is saying I haven't purchased something that I have
Theres this one season of a TV show I own that I've purchased all the episodes, but the store is saying I haven't purchased it, and still gives me the option to purchase again. I did last night, I got duplicates of all the episodes, but it's still ma
-
Hi Experts, We have decrease MRP level in most of IC items and following transaction may be happen after run fresh MRP. If material stock exists more than reorder level, existing PR will be auto deleted by system where PO is not created and released.
-
Podcasts downloaded via wi-fi show as "--:--" after iTunes sync
3rd Gen Ipod Touch 64 GB using iOS4 attaching to Windows 7 with iTunes 9.2. I manually sync videos, music, apps, podcasts. I download about a half dozen podcasts via wi-fi every week. Ever since the upgrade to iOS4, whenever I attach my iTouch to iTu
-
Report previews and prints with strange characters
I have a custom XI application which uses CCrystalReportViewer11 (C++ wrapper around ActiveX control) to preview reports. This works for hundreds of installations, but for one the text is displayed and printed with strange characters. If the customer