Command to see transmit qeueing drops in Nexus 5548

Hello, 10g links in our core are getting rather congested as seen by MRTG graphs. Any command on Nexus 5548 to show transmit queuing drops on a given interface?

You could use #show queing interface eth 1/1
it shows you output similar as below:
NEXUS-1# show queuing interface ethernet 1/1
Ethernet1/1 queuing information:
TX Queuing
    qos-group sched-type oper-bandwidth
        0       WRR            100
RX Queuing
    qos-group 0
    q-size: 470080, HW MTU: 9216 (9216 configured)
    drop-type: drop, xon: 0, xoff: 470080
    Statistics:
        Pkts received over the port             : 222434
        Ucast pkts sent to the cross-bar        : 199674
        Mcast pkts sent to the cross-bar        : 22760
        Ucast pkts received from the cross-bar : 101087
        Pkts sent to the port                   : 145083
        Pkts discarded on ingress               : 0
        Per-priority-pause status               : Rx (Active), Tx (Inactive)
Total Multicast crossbar statistics:
    Mcast pkts received from the cross-bar      : 43996

Similar Messages

Nexus 5548 and Define static route to forward traffic to Catalyst 4500

Dear Experts,
Need your technical assistance for the Static routing in between Nexus 5548 and Catalyst 4500.
Further I connected both Nexus 5548 with Catalyst 4500 as individual trunk ports because there is HSRP on Catalyst 4500. So I just took 1 port from each nexus 5548, make it trunk with the Core Switch (Also make trunk from each Switch each port). Change the speed on Nexus to 1000 because other side on Catalyst 4500 line card is 1G RJ45.
*Here is the Config on Nexus 5548 to make port a Trunk:*
N5548-A/ N5548-B
Interface Ethernet1/3
Switchport mode trunk
Speed 1000
Added the static route on both nexus for Core HSRP IP: *ip route 0.0.0.0/0 10.10.150.39 (Virtual HSRP IP )*
But I could not able to ping from N5548 Console to core Switch IP of HSRP? Is there any further configuration to enable routing or ping?
Pleas suggest

Hello,
Please see attached config for both Nexus 5548. I dont have Catalyst 4500 but below is simple config what I applied:
Both Catalyst 4500
interface gig 3/48
switchport mode trunk
switchport trunk encap dot1q
On Nexus 5548 Port 1/3 is trunk
Thanks,
Jehan

After navigating (sometimes downloading pictures, sometimes not) for approximately 10 minutes, I can no longer see contents of drop down menues, then Firefox freezes up and I have to use Ctrl/Alt/Delete to end my internet experience.

After navigating (sometimes downloading pictures, sometimes not) for approximately 10 minutes, I can no longer see contents of drop down menus, then Firefox freezes up and I have to use Ctrl/Alt/Delete to end my internet experience.
== This happened ==
Every time Firefox opened
== After upgrading to 3.6

Step by step, how did you arrive at seeing this agreement?

Tell me the COMMAND to see the Explain Plain in Oracle SQL * Plus

HI all,
Tell me the COMMAND to see the Explain Plain in Oracle SQL * Plus?
Regards,
Balaji.C

SET AUTOT TRACE EXPor EXPLAIN PLAN ... and @?/rdbms/admin/utlxpls
SCOTT@lsc01> explain plan for select * from dept where deptno=10;
Explained.
SCOTT@lsc01> @?/rdbms/admin/utlxpls
PLAN_TABLE_OUTPUT
Plan hash value: 2852011669
| Id | Operation                   | Name    | Rows | Bytes | Cost (%CPU)| Time     |
|   0 | SELECT STATEMENT            |         |     1 |    20 |     1   (0)| 00:00:01 |
|   1 | TABLE ACCESS BY INDEX ROWID| DEPT    |     1 |    20 |     1   (0)| 00:00:01 |
|* 2 |   INDEX UNIQUE SCAN         | PK_DEPT |     1 |       |     0   (0)| 00:00:01 |
Predicate Information (identified by operation id):
   2 - access("DEPTNO"=10)

What is the command to see the database

what is the command to see the database?iam using oracle express edition in that i tried to create a database but it showing database already created.
i need to check which database is created.

Probably you are thinking that Oracle database is a kind of file something like which we sees other files like .txt, .doc, .pdf etc which we sees by ls or dir commands. Of course there are files for Oracle database, but they have their own nomenclature and setup which finds in C:\oraclexe\oradata\XE\ (For example in Windows) or /usr/lib/oracle/xe/oradata/XE/ (For example in Linux).
By default, the database is started for you after installation and every time your computer is restarted. However, to reduce the overall performance load on the system, you can manually stop the database, and then manually restart it later.
Oracle&reg; Database Express Edition
Ok, now if you wish to login to the database (we don't says "see" the database, because database is different thing than a picture or image ), you just open your command window and say :
sqlplus sys/your_password_of_sys_user as sysdba
If you get SQL> prompt, you have logged in the database as sys user and this is your database.
If you wish to login with different user then you can :
1.login from command window by sqlplus username/password
2.login from SQL> prompt by connect username/password
Regards
Girish Sharma

What is the command to see if there is any faults in an Aruba Controller.

Q: What is the command to see if there is any faults in an Aruba Controller?
A: The command in the below screen shot will tell us what are the active faults that occurred in an Aruba Controller.
The output that is shown in above screen shot shows that active faults.

Hi.
I can suggest show call active voice or show voice call status or show sip-ua call brief in case of SIP TSP.
HTH
Regards.
Carlo

Command to see the memory ,cpu etc.

Anyone can tell me the command to see the memoery usage ,cpu usage etc ,like the 'top ' command in unix.
Please reply.

Assuming you're using Solaris 8 or above try prstat
prstat -am will show more or less the same output as TOP.
There's also commands such as swap -l and swap -s, vmstat, mpstat, iostat which can be used to monitor performance as well.

Is there any command to see dfc memory on SUP32?

Is there any command to see dfc memory on SUP32?

I don't know if the Sup32's support dfc's or not or if it's only the 720's . To see this on the 720's you would have to log into the individual DFC cards by using the "attach slot#" command and then do a show version , this shows how much memory is on the indivdual cards . There is also a lot of other things you can look at in there , they have their own individual logs etc.... There is a a whole "show" command set just for the dfc's .

Install pbr feature nexus 5548

I am in need of Policy Based Routing for a new project. At my core I have a couple of Nexus 5548s clustered together. I go into configure terminal and run the command "feature pbr" and the return is invalid. So I check the license with the command "show license usage" and I get the following output:
Feature Ins Lic Status Expiry Date Comments
Count
FCOE_NPV_PKG No - Unused -
FM_SERVER_PKG No - Unused -
ENTERPRISE_PKG Yes - Unused Never -
FC_FEATURES_PKG Yes - Unused Never -
VMFEX_FEATURE_PKG No - Unused -
ENHANCED_LAYER2_PKG No - Unused -
LAN_BASE_SERVICES_PKG Yes - In use Never -
LAN_ENTERPRISE_SERVICES_PKG Yes - Unused Never -
From here I see that the enterprise package is installed and is unused. How can I gain access to the enterprise features? I found a document here that says "Ensure that you are in the correct VDC (or use the switchto vdc command). " The switchto vdc command is also invalid. What am I missing?
Eric

I realise this is a very old post however I wanted to post here in case others are still looking for this feature. PBR is now supported in version 6.0(2)N2(1) on Nexus 5k.
RELEASE NOTES: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/release/notes/6_02/Nexus5500_Release_Notes_6_02.html#pgfId-472355

Help please with TACACS authentication from a Nexus 5548

I cannot get login working via TACACS from my Nexus 5548. I've tried creating a group and a single server with key etc.
Config is simple:
tacacs-server key 7 ************
ip tacacs source-interface Vlanx
aaa group server tacacs+ tacacs
server 10.x.y.z
The test aaa command shows it's authenticating:
NEX01# test aaa server tacacs+ 10.x.y.z <username> <password)
user has been authenticated
Debug shows this:
NEX01# 2011 Jun 8 12:31:03 NEX01 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user <username> from 10.x.y.z- login[1691]
Am I doing something glaringly wrong here?
Any advice is greatly appreciated.
Thank you.

Hi Paul,
Looks like may be the packet dont have the route ACS when you try to login .
Can you share sh run of the switch ?
Also do you see failed attempt on tacacs server side. ?
Can you ping tacacs server with source interface Vlanx?
Thanks
Waris Hussain

Link Error Nexus 5548

Hi All,
I have issues with Nexus 5548 ports 1000Gb ports. They go down after sometime with the error " Link not connected " while the links are connected. When i move the connections to other ports they work but after a while the go down again with the same error. I can confirm that is currently down was working and its currently connected. Has anyone seen the error before?
Kindly see the output from the interface thats currently down below:
VNX_NEXUS# sho interface eth1/11
Ethernet1/11 is down (Link not connected)
Hardware: 1000/10000 Ethernet, address: 002a.6a71.1f92 (bia 002a.6a71.1f92)
Description: Link_to_EMC_RPA3
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
auto-duplex, 1000 Mb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 2d23h
Last clearing of "show interface" counters 5w6d
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 0 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 0 bps, 0 pps; output rate 0 bps, 0 pps
RX
43384443 unicast packets 30 multicast packets 1496 broadcast packets
43385969 input packets 7837558138 bytes
0 jumbo packets 0 storm suppression bytes
0 runts 0 giants 0 CRC 0 no buffer
0 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
0 Rx pause
TX
56587244 unicast packets 3937125 multicast packets 1487058 broadcast packets
62011427 output packets 14141808286 bytes
0 jumbo packets
0 output errors 0 collision 0 deferred 0 late collision
0 lost carrier 0 no carrier 0 babble 0 output discard
0 Tx pause
18 interface resets

Hi Leo,
What confuses me is that the connection was working. I used the correct cable and the port type as well. How do i resolve this?

Upgrading Nexus 5548

Hi,
We want to upgrade our pair of Nexus 5548 to the new NX-OS 5.1(3)N2(1a) from the 5.0(3)N1(1c) version. We would like to use the ISSU procedure. But when we execute the command "show spannig-tree issu-impact" we get the following output:
No Active Topology change Found!
Criteria 1 PASSED !!
No Ports with BA Enabled Found!
Criteria 2 PASSED!!
List of all the Non-Edge Ports
Port VLAN Role Sts Tree Type Instance
Ethernet2/8 1803 Desg FWD PVRST 1803
The 1803 vlan is only used for the peer-keepalive link and it only exists on these two Nexus. So one of the two Nexus needs to be the STP root. That makes the ports on that vlan to be in designated-forwarding state, which is not supported for the ISSU:
sh run int e2/8
!Command: show running-config interface Ethernet2/8
!Time: Fri Jun 8 17:04:33 2012
version 5.0(3)N1(1c)
interface Ethernet2/8
switchport access vlan 1803
speed 1000
That is the only port that belongs to that VLAN and it is directly connected to the other Nexus 5548. So the only way we see to avoid this port of being in designated-forwarding state is to apply the "no spanning-tree vlan 1803" command. Would it be a problem?
We can imagine that introducing the "spanning-tree port type edge" should not be a good idea, shouldn´t it?
Thank you very much for your help!
Josu

Hi,
Reviewing all the prerequisites for the ISSU, we have seen the following:
SSU and Layer 3
Cisco Nexus 5500 Platform switches support Layer 3 functionality. However, the system cannot be upgraded with the ISSU process (non disruptive upgrade) when Layer 3 is enabled. It is required to unconfigure all Layer 3 features to be able to upgrade in a non disruptive way with an ISSU.
We have the interface-vlan feature enabled. But it is only used for two interfaces:
- interface-vlan 510 --> It is only used in order connect to the switch
- interface-vlan 1803 --> The one used for the keepalive
We could administratevely shutdown the interface-vlan 510. But we could not do so with the interface-vlan 1803, since it is used for the keepalive. If we execute "no feature interface-vlan", would the keepalive stop working?
When we execute "sh install all impact ..." command the Nexus does not tell anything about this feature. Is really recommended to disable it? Is it needed for the ISSU procedure?
Thank you very much in advance!!
JOSU

Upgrading Nexus 5548 UP, Release 5.1(3)N2(1b)

Hi,
I try upgrading my Nexus 5548 with the release 5.1(3)N2(1b)
But I see that the image is'y not compatibible with the module 1 !!!
I followed the Upgrade and Downgrade Guide.
Help me.
********************************************** CLI output *************
sw-tdb-nx5548-1# show install all status
This is the log of last installation.
Verifying image bootflash:/n5000-uk9-kickstart.5.1.3.N2.1.bin for boot variable "kickstart".
SUCCESS
Verifying image bootflash:/n5000-uk9.5.1.3.N2.1b.bin for boot variable "system".
SUCCESS
Verifying image type.
SUCCESS
Extracting "system" version from image bootflash:/n5000-uk9.5.1.3.N2.1b.bin.
SUCCESS
Extracting "kickstart" version from image bootflash:/n5000-uk9-kickstart.5.1.3.N2.1.bin.
SUCCESS
Extracting "bios" version from image bootflash:/n5000-uk9.5.1.3.N2.1b.bin.
SUCCESS
Extracting "fexth" version from image bootflash:/n5000-uk9.5.1.3.N2.1b.bin.
SUCCESS
Recommended action::
"Module 1 might not be supported in the new image,
it should be powered off before proceeding with install".
Performing module support checks.
SUCCESS
Notifying services about system upgrade.
SUCCESS
Compatibility check is done:
Module bootable          Impact Install-type Reason
     1        no             n/a           n/a Incompatible image
   101       yes non-disruptive       rolling
Images will be upgraded according to following table:
Module       Image         Running-Version             New-Version Upg-Required
     1      system             5.1(3)N2(1)            5.1(3)N2(1b)            no
     1   kickstart             5.1(3)N2(1)             5.1(3)N2(1)            no
     1        bios      v3.5.0(02/03/2011)      v3.5.0(02/03/2011)            no
     1      SFP-uC                v1.0.0.0                v1.0.0.0            no
   101       fexth             5.1(3)N2(1)            5.1(3)N2(1b)           yes
     1   power-seq                    v1.0                    v1.0            no
     3   power-seq                    v2.0                    v2.0            no
     1          uC                v1.2.0.1                v1.2.0.1            no
sw-tdb-nx5548-1#
sw-tdb-nx5548-1#
sw-tdb-nx5548-1#

I was using an bad command, the right one is:
install all kickstart bootflash:n5000-uk9-kickstart.5.1.3.N2.1b.bin system bootflash:n5000-uk9.5.1.3.N2.1b.bin
Now the Nexus is upgraded.
Regards

Prime Infrastructure 2.0 and Nexus 5548, SSH credentials fail

Hi,
I'm having problem getting the Prime Infrastructure 2.0 to login with SSH to a Nexus 5548 to do an inventory. I get "Wrong Telnet/SSH credentials". But when I use the same credentials from another SSH-client it works fine. I also tested to SSH from the console of the Prime-server and that also works fine.
Any ideas???
Regards,
Stefan Lindkvist

I have PI 2.0 working against Nexus 5k's in two different installations. See below for an example (click to enlarge).
Have you put in an entry in both the login and enable fields (even though they are not separately required when logging in directly)?

Fabric with two Nexus-5548 and a brocade switch does not get fabric updates

We have a fabric containing two Nexus 5548 and a Brocade 5000 switch in interop mode 2. When i make changes to the zoning, the first nexus (the fabric principal) and the brocade switch see the zone changes. The second Nexus switch does not see it. There are no error messages but the change just can't be seen. What can i do to find out, what goes wrong ?

Ouch, deprecated is not the word i wanted to read
We are using 5.1(3)N1(1a) on nexus-rz1-a
and 6.0(2)N1(2) on nexus-rz2-a.
The fabric can be seen :
nexus-rz2-a# show fcs ie vsan 10
IE List for VSAN: 10
IE-WWN                   IE     Mgmt-Id Mgmt-Addr (Switch-name)
10:00:00:05:1e:90:57:27 S(Rem) 0xfffc01 10.88.133.110 (bc-san1)
20:0a:00:2a:6a:72:ba:01 S(Loc) 0xfffc1c 10.88.133.105 (nexus-rz2-a)
20:0a:54:7f:ee:7f:dc:01 S(Adj) 0xfffc0b 10.88.133.100 (nexus-rz1-a)
[Total 3 IEs in Fabric]
nexus-rz1-a# show fcs ie vsan 10
IE List for VSAN: 10
IE-WWN                   IE     Mgmt-Id Mgmt-Addr (Switch-name)
10:00:00:05:1e:90:57:27 S(Adj) 0xfffc01 10.88.133.110 (bc-san1)
20:0a:00:2a:6a:72:ba:01 S(Adj) 0xfffc1c 10.88.133.105 (nexus-rz2-a)
20:0a:54:7f:ee:7f:dc:01 S(Loc) 0xfffc0b 10.88.133.100 (nexus-rz1-a)
[Total 3 IEs in Fabric]
I try to distribute the zoneset this way:
zoneset distribute vsan 10
Zoneset distribution initiated. check zone status
nexus-rz1-a# show zone status
VSAN: 10 default-zone: deny distribute: full Interop: 2
    mode: basic merge-control: allow
    session: none
    hard-zoning: enabled broadcast: disabled
Default zone:
    qos: none broadcast: disabled ronly: unsupported
Full Zoning Database :
    DB size: 6291 bytes
    Zonesets:1 Zones:62 Aliases: 44
Active Zoning Database :
    DB size: 10243 bytes
    Name: FABRIC1 Zonesets:1 Zones:60
Status: Zoneset distribution completed at 08:06:00 UTC Dec 3 2013
nexus-rz2-a# show zone status
VSAN: 1 default-zone: deny distribute: active only Interop: default
    mode: basic merge-control: allow
    session: none
    hard-zoning: enabled broadcast: disabled
Default zone:
    qos: none broadcast: disabled ronly: unsupported
Full Zoning Database :
    DB size: 4 bytes
    Zonesets:0 Zones:0 Aliases: 0
Active Zoning Database :
    Database Not Available
Status:
VSAN: 10 default-zone: deny distribute: full Interop: 2
    mode: basic merge-control: allow
    session: none
    hard-zoning: enabled broadcast: disabled
Default zone:
    qos: none broadcast: disabled ronly: unsupported
Full Zoning Database :
    DB size: 6291 bytes
    Zonesets:1 Zones:62 Aliases: 44
Active Zoning Database :
    DB size: 10243 bytes
    Name: FABRIC1 Zonesets:1 Zones:60
Status: Activation completed at 13:03:42 UTC Dec 2 2013

Command to see transmit qeueing drops in Nexus 5548

Similar Messages

Maybe you are looking for