Communicate with MTP device using C# desktop application

I want to communicate(Read / Write) with android phone connected with desktop machine as MTP device using C# in Desktop application.
When phone is connected in MTP mode, not as USB drive.
Ram Swami

Hi,
mybe the links below can assist you:>
WPD Application Programming Interface
WPD: Transferring Content
MTP, WPD, OMG
Mark as answer or vote as helpful if you find it useful | Ammar Zaied [MCP]

Similar Messages

Communicate with Modbus device using OPCLabVIEW.

Hi all,
I am using LabVIEW 6i with DSC. I want to connect Modbus device. At some other place I saw that this is very easy with OPCLookout server but we don't have this opc server toolset. So I want to communicate Modbus device using LabVIEW DSC only. Did any one had done it please help me out.
Thanking you.
Vishal

Hi thanks for the reply.
In first para you are talking about some server. Is it OPCLookout / OPCLabVIEW server or anything else please let me know.
As far as the OPCLookout server is concern, we got it. But our excate requirement is as follows.
>>>>> We want to connect our modbus device with FP.
We have flow controller working with modbus protocol. this controller store some parameters. At particular time(daily) we want to get this readings in FP and then pass it to some other PC or main controller. But I am not aware how the lookoutopc server would work with FP. I think that if we could connect modbus with LabviewDscOPC server than DSC will take care for the communication ( Not sure & not know how, if u know please guide me). Due to this only I am ve
ry strict for the LabviewDsc.
In third pare u told about to make driver for modbus. Please guide me how could i do this. I tried to communicate with modbusdemobox (ni one) using serialport vis. but not able to communicate.
Please guide me.
Thanking you.
Regards,
Vishal

Can I use virtual bench to measure/communicate with other device by I2C etc?

Hi,
Can I use vitrual bench to measure I2C/SPI/CAN by digital I/O or logic analyzer?
And is it possible using digital I/O to communicate with other device by I2C etc?
Thanks,
Jimmy

You might be able to get it to work (not sure how fast the DIO on the Virtual Bench can go), but for I2C, I would recommend using something that is actually meant for it, like the USB-8451 or USB-8452.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

HPlip: "Unable to communicate with the device" error

Hello Arch Community, I've been a user of Arch for a while and most of it just worked out of the box. However, I had my HP 6300 working through a direct connection. But a couple of days ago it just broke.
I've tried everything I could think of to make it back but all has been unsuccesful, I removed the printer and tried to add it again (sorry, old Windows habit, there most of the time works), however, I couldn't add the printer, it fails with the error: "Unable to communicate with the device. Please check the device and try again.", I added myself to the ld group (shouldn't matter, but I did it anyway)
I have cups 1.4.2.
Hp-check:
HP Linux Imaging and Printing System (ver. 3.9.10)
Dependency/Version Check Utility ver. 14.3
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the HPLIP supplied
tarball (.tar.gz or .run) to determine if the proper dependencies are installed to successfully
compile HPLIP.
2. Run-time check mode (-r or --run): Use this mode to determine if a distro supplied package (.deb,
.rpm, etc) or an already built HPLIP supplied tarball has the proper dependencies installed to
successfully run.
3. Both compile- and run-time check mode (-b or --both) (Default): This mode will check both of the
above cases (both compile- and run-time dependencies).
Saving output in log file: hp-check.log
Initializing. Please wait...
| SYSTEM INFO |
Basic system information:
Linux carloslicea-laptop 2.6.31-ARCH #1 SMP PREEMPT Tue Nov 10 19:48:17 CET 2009 i686 Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz GenuineIntel GNU/Linux
Distribution:
unknown 0.0
Checking Python version...
OK, version 2.6.4 installed
Checking PyQt 4.x version...
OK, version 4.6.1 installed.
Checking for CUPS...
Status: el planificador de tareas se está ejecutando
Version: 1.4.2
warning: /etc/cups/cupsd.conf file not found or not accessible.
Checking for dbus/python-dbus...
dbus daemon is running.
python-dbus version: 0.83.0
| COMPILE AND RUNTIME DEPENDENCIES |
note: To check for compile-time only dependencies, re-run hp-check with the -c parameter (ie, hp-check -c).
note: To check for run-time only dependencies, re-run hp-check with the -r parameter (ie, hp-check -r).
Checking for dependency: CUPS - Common Unix Printing System...
OK, found.
Checking for dependency: CUPS DDK - CUPS driver development kit...
warning: NOT FOUND! This is an OPTIONAL/RUNTIME ONLY dependency. Some HPLIP functionality may not function properly.
Checking for dependency: CUPS devel- Common Unix Printing System development files...
OK, found.
Checking for dependency: CUPS image - CUPS image development files...
OK, found.
Checking for dependency: DBus - Message bus system...
OK, found.
Checking for dependency: gcc - GNU Project C and C++ Compiler...
OK, found.
Checking for dependency: GhostScript - PostScript and PDF language interpreter and previewer...
OK, found.
Checking for dependency: libcrypto - OpenSSL cryptographic library...
OK, found.
Checking for dependency: libjpeg - JPEG library...
OK, found.
Checking for dependency: libnetsnmp-devel - SNMP networking library development files...
OK, found.
Checking for dependency: libpthread - POSIX threads library...
OK, found.
Checking for dependency: libtool - Library building support services...
OK, found.
Checking for dependency: libusb - USB library...
OK, found.
Checking for dependency: make - GNU make utility to maintain groups of programs...
OK, found.
Checking for dependency: PIL - Python Imaging Library (required for commandline scanning with hp-scan)...
OK, found.
Checking for dependency: PolicyKit - Administrative policy framework...
warning: NOT FOUND! This is an OPTIONAL/RUNTIME ONLY dependency. Some HPLIP functionality may not function properly.
Checking for dependency: PyQt 4 DBus - DBus Support for PyQt4...
OK, found.
Checking for dependency: Python DBus - Python bindings for DBus...
OK, found.
Checking for dependency: Python devel - Python development files...
OK, found.
Checking for dependency: Python libnotify - Python bindings for the libnotify Desktop notifications...
warning: NOT FOUND! This is an OPTIONAL/RUNTIME ONLY dependency. Some HPLIP functionality may not function properly.
Checking for dependency: Python XML libraries...
OK, found.
Checking for dependency: Python 2.3 or greater - Required for fax functionality...
OK, found.
Checking for dependency: Python 2.2 or greater - Python programming language...
OK, found.
Checking for dependency: Reportlab - PDF library for Python...
warning: NOT FOUND! This is an OPTIONAL/RUNTIME ONLY dependency. Some HPLIP functionality may not function properly.
Checking for dependency: SANE - Scanning library...
OK, found.
Checking for dependency: SANE - Scanning library development files...
OK, found.
Checking for dependency: scanimage - Shell scanning program...
OK, found.
Checking for dependency: xsane - Graphical scanner frontend for SANE...
OK, found.
| HPLIP INSTALLATION |
Currently installed HPLIP version...
HPLIP 3.9.10 currently installed in '/usr/share/hplip'.
Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf. Generated from hplip.conf.in by configure.
[hplip]
version=3.9.10
[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/HP
ppdbase=/usr/share/ppd
doc=/usr/share/doc/hplip-3.9.10
icon=/usr/share/applications
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv/hp
# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
pp-build=no
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=yes
foomatic-drv-install=yes
foomatic-ppd-install=yes
foomatic-rip-hplip-install=yes
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.9.10.72
restricted-build=no
ui-toolkit=qt4
qt3=no
qt4=yes
policy-kit=no
hpijs-only-build=no
lite-build=no
udev-acl-rules=no
hpcups-only-build=no
hpijs-only-build=no
Current contents of '/var/lib/hp/hplip.state' file:
# hplip.state - HPLIP runtime persistent variables.
[plugin]
installed=0
eula=0
Current contents of '~/.hplip/hplip.conf' file:
[last_used]
printer_name =
printer =
working_dir = .
device_uri = "hp:/net/Officejet_6300_series?zc=HP56B6CF"
[commands]
scan = /usr/bin/xsane -V %SANE_URI%
[installation]
version = 3.9.10.72
date_time = 12/04/09 23:41:37
[settings]
systray_messages = 0
systray_visible = 1
[fax]
email_address =
voice_phone =
[refresh]
rate = 30
enable = false
type = 1
[polling]
enable = false
device_list =
interval = 5
| DISCOVERED USB DEVICES |
No devices found.
| INSTALLED CUPS PRINTER QUEUES |
lpstat
Type: Unknown
Device URI: No se han añadido destinos.
| SANE CONFIGURATION |
'hpaio' in '/etc/sane.d/dll.conf'...
OK, found. SANE backend 'hpaio' is properly set up.
Checking output of 'scanimage -L'...
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
| PYTHON EXTENSIONS |
Checking 'cupsext' CUPS extension...
OK, found.
Checking 'pcardext' Photocard extension...
OK, found.
Checking 'hpmudext' I/O extension...
OK, found.
Checking 'scanext' SANE scanning extension...
OK, found.
| USER GROUPS |
dbus hal network video audio optical storage power users policykit vboxusers
| SUMMARY |
error: 4 errors and/or warnings.
Please refer to the installation instructions at:
http://hplip.sourceforge.net/install/index.html
Done.
Albeit it has errors, I can't see how they are releated (cups does have a conf file, but it seems that *my* user can't access it, expected 'couse it's owned by root). Any ideas?

Hi
I had the same problem. The solution is to change the network discovery mode to SLP or add manually the IP address of your printer at the first step of the hp setup wizard. After you install the printer successfully, check the maximum resolution of the driver. Mysteriously, for me the maximum resolution was restricted to 600 dpi so I downgraded to the previous version of HPLIP and got back the 1200 dpi option. Please let me know if you have this issue too. I have posted this question in the hplip forums, but I haven't received any replies yet.

USB comunication with a device using LabWindows CVI 7.1 or more late.

Hello Partners.
I am try to get information about USB comunication with a device using CVI 7.1 or more late, I will need to developed a aplication for comunicate with a device but I have not idea of How do this. I know how comunicate with the serial port in CVI, but I never have developed any application using the USB port.
Do you know which are the requirements for do this??
I have read some information and I am seeing that I needed the driver of device for do this but I do not know what is the command line that will need to send in the aplication for comunicate with my device.
Somebory knows how can I do this in my application??
Somebory has some exemplo code in where I can see the commands that I needed to send to the USB port?
Thanks a lot for your help.
I will be to hope some suggestion.

hi,
think there are three possibilities:
1. the product comes with an own driver & api
2. the product comes with an FTDI-device to communicate over
2.1 you can talk with the device over a virtual COM (rs232)
2.2. you can talk with the device over the D2XX-layer (look at the FTDI-webside: "D2XX Programmers guide....")
best regards
Simon

I have VISA3.0,do i need any further instrument drivers to communicate with my device?

If I get Visa 3.0,will that be sufficient to communicate with my device via matlab or will I need
further instrument drivers?

Hello,
It is not very clear what you want to do. For what I understand you have an instrument that you are connecting to a gpib, or serial or tcp port in your computer. Matlab should be able to do the link between VISA and the instrument. Are you using NI-VISA? Are you using LabVIEW or any other software?
If you are using one of our GPIB cards or serial cards, then you would also need the driver for that hardware.
Hope this answers your question. If it doesn�t please provide more description like if you would like to call a Matlab script through LabVIEW or something like that.
Thank you,
Ricardo S.

In the latest iOS updates, did Apple change the way Airplay communicate with other devices through Wifi?

Short :
In the latest iOS updates, did Apple change the way Airplay communicate with other devices through Wifi?
Detailed:
We had a glitch with our Apple TV 3A 3-4 weeks ago and had to factory reset it (we reconfigured it with the exact same configuration than before the crash), it's now running iOS 7.0.2, I can't saw which version it ran before the problem though.
It's used in a business environment with 30+ iPads 2, half of them are updated to 8.1.1 and the other half to 8.1.2. We use the latest iTunes version.
Before the glitch that required a reset, all the iPads were detecting and mirroring when needed to the Apple TV, but now the iPads don't see the Apple TV in their list of Airplay devices anymore (but they detect various other devices inside our network).
I have to add that our Apple TV is able to navigate the movie store correctly, so I assume that it's not an internet restriction issue from our end (also, the APple TV do not see either any of the many iPads on its device-detection screen.
We successfully connected an iPhone 5S and an iPhone 6 through P2P Airplay, so it's not the issue, but when we connected the iPhones to our Wifi network (Same as all the other devices are using) the Apple TV suddenly disappeared from the choices.
Hence the reason why I inquire to the possibility that some changes were made in one of the latest iOS revisions, if so, we would require some details so we can adjust our Wifi configuration accordingly to allow the proper detection of devices.
P.S. I tried the basic troubleshooting of Airplay problems with no avail. Airplay button is displaying on the control panel, Airplay do not show the Apple TV at all (so it's not either the trick to display the Mirroring button), we also already proceeded to the suggested devices reboots, so my issue is quite more complex I believe.
Thanks in advance.

PhotogYogi wrote:
I Have the same issue on a brand new iPad mini 2. My battery is only lasting up to 5 hours. I went on chat with Apple last night and they said my battery is fine and its a Safari issue. I'm literally losing 1% every 3-4 minutes. I tried recalibrating my battery, signing out of iCloud, shutting off all locations, turning off background app refresh, restoring network settings, restoring all, and finally restoring from iTunes with no luck. This is just awful. I got this iPad so I could use it on my long flight for a trip I have coming up, and unfortunately, it's not going to last that long, plus I'm concerned about how many times i will be recharging my battery because of this since battery's do have a life cycle dependent on the number of charges. This is frustrating and needs to be fixed ASAP and addressed by Apple.
By the way, Apple told me to bring my device to the Apple Store because it's still under warranty. That's great and all, but I'm going to waste my time if there is no fix for this issue.
Ok so you want Apple to address the problem, but yet you don't want to take it to them just in case they can't fix it? What if they can fix it? Complaining here certainly won't fix it.

Fax from PC: unable to communicate with the device.

Hi,
Im facing this issue where i am unable to send fax through my PC.
Some info:
Device: laserjet CM1415fnw
IP address for laserjet: 192.168.1.250
subnet: 255.255.255.0
gateway: 192.168.1.254
OS: winvista
antivirus: using AVG free edition 2012
both my print drivers and fax drivers are using the same network port which i set manually by creating a tcp/ip port (192.168.1.250).
I am able to communicate with printer to print, scan but not fax.
When i chose the fax driver to print to, it will send the job, and then display the error:
Unable to communicate with the device.
The device may be disconnected, powered off, or its network settings may have changed.
I tried to install using the drivers downloaded from HP and it created a "HP Fax Port" which i tried changing the port to use this instead, still same error.
A command ping to the ip 192.168.1.250 is getting response.
Anyone have any idea? Or could the AV blocking the drivers from communicating to the printer?

Hi AWI,
I am sorry to hear that you are having issues faxing. I would like some more information from you so I can look further into this issue for you.
Could you respond to me with this info:
Are you able to fax from your printer, stand-alone?
What model of printer do you have?
Are you running Windows or Mac?
Have you printed a Fax Test? If yes, does it pass or fail on anything?
Look forward to hearing from you!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Hello, I have created a distribution kit for my program.The problem is that the when the program is installed onto another computer, it fails to communicate with field point (Using FP-AO-200 and FP-AO-1000). Help is greatly appreciated, Thanks faen9901

Hi Everyone,
I have a program that sends information(analog output) to lab windows cvi in the form of a text file or user input.
The program runs on the computers that I have the field point explorer and lab windows cvi installed on. In order to run the program without always installing labwindows/cvi and field point; I wanted to create an executable file that could be load on another computer.
I used the create distribution kit part of labwindows/cvi to do this.After creating the distribution kit, I then installed it
to another computer.
My user interface appears on the screen, when the user clicks on the exe. file, but no data is sent to the field point module. I know that the data is being read from the user and textfile because in it appears in the uir.
The following are some details about the problem:
1. On another computer without labwindows/cvi and field point explorer not installed - no data is sent to field point module
I know this because a current is being read on the current meter connected to field point module.
My questions are the following:
1. What are the possible reasons for the data not being sent to the field point module?
2. Do I still need to create an iak. (Installing Field point Explorer) file stored on any new computer that I install my created distribution kit file too?
Thankyou very much for any help that you can provide. I greatly appreciate it.
Faen9901

Re: Hello, I have created a distribution kit for my program.The problem is that the when the program is installed onto another computer, it fails to communicate with field point (Using FP-AO-200 and FP-AO-1000). Help is greatly appreciated, Thanks faen9901Faen9901,
1) If you do not install FieldPoint Explorer, the FieldPoint Server is not installed so there is nothing on the target computer that knows how to talk to the FieldPoint system.
2) Yes, you need an IAK file on the target computer. Assuming the settings (i.e. com port#) are identical you can simply include the iak file as part of the distribution.
3) You also need to include as part of your installer the file "fplwmgr.dll". If this file is not installed, your program will not be able to access the FieldPoint Server. Alternatively, this file is installed automatically if FieldPoint Explorer detects LabWindows/CVI or Measurement Studio Development versions on the target computer or if you choose to do a custom FieldPoint Explorer installation and
choose to provide LabWindows/CVI support.
Regards,
Aaron

Any way to communicate with Serial PORT using JavaScript

is there any way to communicate with Serial PORT using JavaScript ??
Dont tell me to do it in java because I need to this on client side not on server side.
such as when client pressed the button, a javascript function will be called and in that function I need to communicate with the serial port of that client... That action will not go to server side.

Is there any way to send a string of bytes to the serial port from the client side ?
Just a button on the web page that sends out stuff to the comport.
I was hoping to do this using java script also ..

Communicate with the scanner using LabvIEW

Hello,
Anyone can help me or show me how to communicate with the USB devices like scanners?
Is there extra library needed for this to work?
Thanks...

Hi simply_ynan,
What is the application you are trying to implement with this device? If you plan to use this scanner with our Vision Acquisition Software (IMAQdx driver), then the scanner would have to be DirectShow compliant. This Knowledge Base may be helpful to you. Thanks!
Kim
Applications Engineer
National Instruments

Communicate with servlet after using Java Web Start?

Is it possible to communicate with servlet to get data back and forth
after using Web Start to download the client application?
The demos come with Java Web Start are applications which are
standalone, don't need communicate with the servlet on Web server
after being launched. I am wondering if it is possible, and how (HTTP
& JAX-RPC)?
Thanx in advance.

I've done this using HTTP. I get the server and port from the codebase:
BasicService bs = null;
try {
bs = (BasicService)ServiceManager.lookup("javax.jnlp.BasicService");
String codeBase = bs.getCodeBase().toString();
and use the java.net.HttpURLConnection and java.net.URL classes to send HTTP parameter values to the servlet and to receive results from the HttpURLConnection's input stream.

Best way to communicate with IEEE device

Hi everyone;
I'm using a Magtrol DSP6001 Dynamometer Controller to control a
dyno. It's GPIB, and I'm able to communicate with it swimmingly,
and I've used it it a number of other apps that I've written.
My problem now is, that I need to be reading the device as fast as
possible, but at the same time, setting the torque at regular
intervals. Here's a better explaination:
I'm controlling a stepper motor (which is the main problem, as all the
other motors I have written apps for using this equipment have been
brushless servos) for an acceptance test, and part of the test requires
that the torque be ramped up gradually until the motor starts missing
steps, and the torque at which this happens is recorded. The
problem is, in order to accurately record the torque value, I need to
be reading the device constantly (not a problem, as the controller is
capable of providing 100 samples/second), but at the same time
gradually increasing the torque.
You can see where the problem arises... if I were to multi-thread
this vi, then I would get randomly occurring IEEE errors, but if I have
the data acquisition in the same loop as the torque increase, then I
don't get nearly enough accuracy. Is this something that a
semephore would be useful for? I have heard something about the
IEEE bus being able to handle some sort of syncronization, but I don't
know much about that...does anyone else?
Has anyone else had this sort of problem before?
Thanks, Geoff
Notes: I'm running the controller in open loop mode... for two
reasons. One, it's easier to have a smoother ramp in open loop by
the nature of the commands used to communicate with it, and two, trying
to obtain the PID settings for this motor was getting to be an absolute
nightmare, and I don't think it worth the time, as it's just a ramp,
not a constant torque. Or am I wrong in thinking that?

Thanks for the reply, but I suppose I should have been more clear... it doesn't exactly answer my question.
I have two loops, both of which need to communicate with the
controller. One loop (top in the image) I need to run several
times faster than the bottom loop, as I need greater accuracy in the
readings (more samples).
The bottom loop will run not as fast as possible - as the top loop will
- but will run every say, 20 milliseconds. You might be asking
why that's not in the image, but that's just the bare bones of what I'm
trying to do.
I can't leave them to their own devices as is, since I'll get random
GPIB errors because both might be trying to write at the same time, or
one might write before the top has read, and then the read will return
an error.
I was just wondering what the best way to go about doing this
is... I'll try using queues to do this type of operation, sorta
like you suggested.
Has anyone ever heard of GPIB being able to do synchronized
communication? (as in, is there a way to have two pieces of data,
one being written and one being read, from the GPIB bus at the same
time? Like, being able to read what's been returned by the
controller, but at the same time writing a new command to the bus?)
Message Edited by Novatron on 07-28-2005 03:49 PM
Attachments:
Example.jpg ‏89 KB

Help With MTP Device- Ple

About 3 weeks ago my Sleek Photo started acting up, and I have tried everything to get it fixed. Any advice would be much appreciated. Here are my specifics:
OS: Windows XP SP2
Media Player: Windows Media Player .0.5722.545
Player: Sleek Photo
Firmware: .0.0
Here's the problem. When I connect the Sleek Photo, I get a popup asking me what I want to do (Sync Music, etc). So far so good. However, when I try to sync (either through Media Player, the Creative Media Explorer, or Napster), I get the error that the device is not found. I also use Napster to Go, which also isn't able to locate the device.
Under Windows Device Manager, the player is listed as an MTP device, with the error that "No Drivers are installed for this device). However, under the driver tab, the driver is listed as version 5.25326.4762 with a date of 2/22/06. Additionally, the device manager window is in a constant state of "refresh", in that the window is MTP tab is constantly expanding and contracting, as if it is continually "relocating" the device. This is accompanied by a popup in the lower right portion of my screen saying that a "New MTP Device found", which continues to reappear constantly.
Here's what I've tried so far:
Updating Napster
Updating Windows Media Player
Rolling back Windows Media Player to version 0
Restoring Windows Media Player to version
Adding the Everyone permission to the USB registry key
Using System Restore to roll back to a time when the device was working
Switching the USB input from the back panel to the front panel
Uninstalling and reinstalling the Sleek Photo firmware (which I had to do from an old computer since mine won't recognize the device from the firmware installation utility, either).
I'd greatly appreciate any suggestions anyone might have. Thanks for looking.

WHen I push the power button it jut comes up wioth a blank screen with the Creative logo.
I tried also plugging it into my CP but the same thing happens.
I removed the battery like you said, but still, no progress.

Specific User receiving Application crash when using Remote Desktop Application

I have a client running a server with their line of business software configured as a remote application. I have one user that when he attempts to run the line of business software as a remote application he receives a APPCRASH error.However if another user
launches the remote application and then signs in as the problem user there is no APPCRASH.
The following information is reported with the error:
Faulting application name: impress.exe, version: 5.1.102.0, time stamp: 0x522f820a
Faulting module name: impress.exe, version: 5.1.102.0, time stamp: 0x522f820a
Exception code: 0xc0000005
Fault offset: 0x003fe41f
Faulting process id: 0x268
Faulting application start time: 0x01cf11ffa8811e46
Faulting application path: C:\data\Impress\impress.exe
Faulting module path: C:\data\Impress\impress.exe
Report Id: 238e8dfc-7df6-11e3-b1b6-001e678ee8f8
After the app crash the is a warning in the event log, but its about 43 seconds later; Event 1530, user Profile Service
Windows detected your registry file is still in use by other applications or services. The file will be unloaded now. The applications or services that hold your registry file may not function properly afterwards.
DETAIL -
1 user registry handles leaked from \Registry\User\S-1-5-21-2105745629-1987324649-1874639966-1224:
Process 328 (\Device\HarddiskVolume2\Windows\System32\svchost.exe) has opened key \REGISTRY\USER\S-1-5-21-2105745629-1987324649-1874639966-1224\Printers\DevModePerUser
just trying to find some sort of hint as to way the remote application would crash for just one user. it is my luck that the one user is the owner.

It looks like the issue was resolved by deleting the problem users profile off of the terminal server. The user can now access the RD application without suffering an APPCRASH error.

Communicate with MTP device using C# desktop application

Similar Messages

Maybe you are looking for