Communication error CPIC return code 019 SAP return code 728. Delta error
Hello Experts,
Would just like to ask if what we suspect is correct. We have running deltas in process chains occurring every early morning. However, upon checking the delta that should have run today, I found that the delta did not push through. I only found this one dump in SM21 that I think is related to the issue:
MNo.
R49 Communication error, CPIC return code 019, SAP return code 728
R5A > Conversation ID: 61442686
R49 Communication error, CPIC return code 019, SAP return code 728
R64 > CPI-C function: CMSEND(SAP)
R5A > Conversation ID: 61443687
R64 > CPI-C function: CMSEND(SAP)
R49 Communication error, CPIC return code 019, SAP return code 728
R5A > Conversation ID: 61444687
R64 > CPI-C function: CMSEND(SAP)
Now we think that the delta did not push through because we are encountering issues with regards to our SAP R/3 system (the source system) and it is currently inaccessible. Did the delta not push through because of the issues and inaccessibility/uber slow processing of our SAP R/3 server? And is the error specified above illustrating this? Any explanation would help. I have already tried looking for similar issues but cannot find anything. Please help. Thanks!
Hi
As far I know, The SAP Gateway carries out CPI-C services within the SAP world, which are based on TCP/IP. These services enable SAP Systems and external programs to communicate with one another.
CPI-C services can be used either in the ABAP program or for the external programs via the interfaces.
As RFC (remote function call) is based on CPI-C, all RFC connections also pass through the SAP Gateway.
Errors When Starting Remote Programs Using Remote Shell
When you use remote shell to start CPIC programs on other hosts, the following conditions apply:
The (gateway) UNIX ID must be available on the other host
The gateway host must be entered in the remote host in the file ".rhosts". This file must be located in the HOME directory of the (gateway) UNIX ID.
The program you want to start must be installed in the HOME directory of the (gateway) UNIX ID on the remote host.
Read more from help
http://help.sap.com/saphelp_nw04s/helpdata/en/99/5f8c0bcb7d4280aa862254cffceada/frameset.htm
Similar Messages
-
RFC Communication - error CPIC return code 020, SAP return code 665
Hello,
I have created RFC destination for connecting SCM system from Solution Manager. Both the systems are Unicode.
I am getting the following error --
ERROR service '?' unknown
LOCATION SAP-Gateway on host gva4103 / sapgw00
COMPONENT NI (network interface)
COUNTER 4028
MODULE
LINE
RETURN CODE -3
SUBRC 0
RELEASE 640
TIME Mon Apr 24 11:28:21 2006
VERSION 37
And in SM21, I am getting following description
Communication error, CPIC return code 020, SAP return code 665
Following are the things I have checked..
1. RFC destination user checked, password reset in SM59 and in the target system
2. checked entries in /etc/services - Entry sapgw03 is present.
Please let me know what all things I need to check.
Thanks and Regards,
VaibhavI solved the problem by myself.
The problem was with the entry in services file only.
I was checking the file on Target system, which had the entry. There was no entry in Host system services file. After modifying the file, the connection now works fine.
Thus for RFC connection, entry of the target system gateway MUST be there in /etc/service of Host system.
Regards,
Vaibhav -
Communication error, CPIC return code 017, SAP return code 236
Hi guys,
Need your advice, my SAP system suddenly appear this messages ( SM21).
Please assist me.
Communication error, CPIC return code 017, SAP return code 236
> CPI-C function: CMINIT(SAP)Hi Uday,
My SAP using ABAP. Version 4.7
All RFC working fine except for the OSS
Error message
Details Page 2 Line 22 System Log: Local Analysis of ALBANIA 1
Time Ty. Nr Cl. User Tcod MNo Text
13:52:36 DIA 01 800 SYSADM R49 Communication error, CPIC return code 017, SAP return code 236
Details
Recording at local and central time........................ 27.03.2009 13:52:36
Task................ 57584 . 01 D1 Dialog work process No. 01
User................ SYSADM
Client.............. 800
Terminal............ 10.0.38.
Session............. 1
Transaction code....
Program name........ SAPMSSY1
Problem class....... K SAP Web AS Problem
Development class... STSK -
Communication error, CPIC return code 017, SAP return code 450
Hi All,
can anyone please tell me more about this error Communication error, CPIC return code 017, SAP return code 450 which is displayed in sm21.
We done post configuration of pi server yesterday, after the configuration we were able to log into Integration Directory and Visual Administator..
But today were are not able to log into both .....while logging into both we are getting authentication error 401.
we checked for users being locked but all users are not locked..even even tried reseting passwords,
also restarted the server but didnt help..
Reward points for helpfull Answers.
Thanks and Regards,
Srikanth.Hi Naidu,
Most common reason encountered for this problem is authorizations on installation. it is important to have both network and local machine admin rights when installing content server software. If you don't, the installation will be successful but you encounter the 401 error. Try reinstalling with correct authorization and you should resolve the issue.
Try regenerating the roles. SU01 -> display each XI user -> open the roles -> double click on the role -> click on the User tab in the role screen then there will be a button for USER COMPARISON do that for all the roles in red.
If that does'nt work out, Take a look at OSS Note 751856 and 796726.
May be your security roles were not adjusted during the upgrade (Note 796726).
if found worth pls do the req
Thanx
Sampath -
Communication error, CPIC return code 002, SAP return code 679
Hi,
Our production system log displayed, large no.of
"Communication error, CPIC return code 002, SAP return code 679". I could not able to find any OSS notes on this.
Please explain with detail steps to resolve this issue or please tell me, If any OSS notes exists/
Thanks in advance
Regards
SrinivasWell, I meant that there are a lot of notes available. Search for "CPIC error".
Also, have you double clicked on the line in the log? That will also give you more information.
Rob -
Communication error, CPIC return code 017, SAP return code 223
In sm59 its throughing error Communication error, CPIC return code 017, SAP return code 223 for SAPOSS connection.
Return code 223 is Network read error.
Check out SAP Note : 421558, it may help you.
Regards,
Zaheer -
Communication error, CPIC return code 020, SAP return code 456
Hi Gurus,
I am facing this error in my BW system system log. "Communication error, CPIC return code 020, SAP return code 456"
Can anyone please helpp in resolving this issue.
Regards
PeterHi Peter,
there is an pretty old note about a similar error ([CPIC return code 020, SAP return code 223|https://websmp102.sap-ag.de/~form/handler?_APP=01100107900000000342&_EVENT=REDIR&_NNUM=512272&_NLANG=EN]). It was related to a BEX Patch. May be you should raise a note at the service market place for your issue.
regards
Siggi -
R49 Communication error, CPIC return code 020, SAP return code 223
SM21,every 15 minutes occurs the following error:
R49 Communication error, CPIC return code 020, SAP return code 223
R5A dialog id :5442063
R64 CPI-C function: CMSEND(SAP)
but the partner system can receive SAP data every 15 minutes.
what does the error mean? and how to solve it ?
thanks ahead.Hi,
The following note 63347 provides more information about the error message.
Regards
Srivatsa.V -
Communication error, CPIC return code 020, SAP return code 223
Hello.
I have system NetWeatver 2004s
Client 101 is a client process integration, UME in ABAP
Sometimes java is restarted...
At that moment in SM21 I can see next log:
16:03:36 RD S2 3 Connection to CPI-C client 016 was closed
16:03:36 RD S7 4 > Partner LU name:
16:03:36 RD S0 R > Host: 10.0.0.53
16:03:36 RD S0 I > Partner TP Name: jlaunch
16:03:36 DIA 007 101 SAPJSF R4 9 Communication error, CPIC return code 020, SAP return code 223
16:03:36 DIA 007 101 SAPJSF R5 A > Conversation ID: 64435936
16:03:36 DIA 007 101 SAPJSF R6 4 > CPI-C function: CMSEND(SAP)
What is this? Why JAVA is restarted ?From dev_jcontrol
[Thr 1] Wed Mar 25 16:03:38 2009
[Thr 1] JControlICheckProcessList: process server0 (pid:9773) died (RUN-FLAG)
[Thr 1] JControlIResetProcess: reset process server0
[Thr 1] JControlICheckProcessList: running flight recorder:
/opt/java1.4/bin/java -classpath ../j2ee/cluster/bootstrap/sap.comtcbloffline_launcherimpl.jar com.sap.engine.offline.OfflineToolStart com.sap.engine.flightrecorder.core.Collector ../j2ee/cluster/bootstrap -node ID47163850 1237887114 -bz /usr/sap/KXD/SYS/global
JControlStartJLaunch: program = /usr/sap/KXD/DVEBMGS04/exe/jlaunch
-> arg[00] = /usr/sap/KXD/DVEBMGS04/exe/jlaunch
-> arg[01] = pf=/usr/sap/KXD/SYS/profile/KXD_DVEBMGS04_pasved
-> arg[02] = -DSAPINFO=KXD_04_server
-> arg[03] = -nodeId=1
-> arg[04] = -file=/usr/sap/KXD/DVEBMGS04/j2ee/cluster/instance.properties
-> arg[05] = -syncSem=186
-> arg[06] = -nodeName=ID47163850
-> arg[07] = -jvmOutFile=/usr/sap/KXD/DVEBMGS04/work/jvm_server0.out
-> arg[08] = -jvmOutMode=append
-> arg[09] = -stdOutFile=/usr/sap/KXD/DVEBMGS04/work/std_server0.out
-> arg[10] = -stdOutMode=append
-> arg[11] = -traceMode=append
-> arg[12] = -locOutFile=/usr/sap/KXD/DVEBMGS04/work/dev_server0
-> arg[13] = -mode=JCONTROL
-> arg[14] = pf=/usr/sap/KXD/SYS/profile/KXD_DVEBMGS04_pasved
-> arg[15] = -DSAPSTART=1
-> arg[16] = -DCONNECT_PORT=49453
-> arg[17] = -DSAPSYSTEM=04
-> arg[18] = -DSAPSYSTEMNAME=KXD
-> arg[19] = -DSAPMYNAME=pasved_KXD_04
-> arg[20] = -DSAPPROFILE=/usr/sap/KXD/SYS/profile/KXD_DVEBMGS04_pasved
-> arg[21] = -DFRFC_FALLBACK=ON
-> arg[22] = -DFRFC_FALLBACK_HOST=localhost
-> lib path = LD_LIBRARY_PATH=/opt/java1.4/jre/lib/IA64W:/opt/java1.4/jre/lib/IA64W/server:/opt/java1.4/jre/../lib/IA64W:/usr/sap/KXD/DVEBMGS04/exe:/usr/sap/KXD/DVEBMGS04/exe::/usr/sap/KXD/DVEBMGS04/exe:/usr/sap/KXD/DVEBMGS04/exe:/usr/sap/KXD/DVEBMGS04/exe:/tmp/sapinst_exe.6709.1224050598:/usr/sap/KXD/SYS/exe/run:/oracle/client/10x_64/instantclient:/usr/lib:/usr/sap/KXD/DVEBMGS04/j2ee/os_libs:/usr/sap/KXD/DVEBMGS04/exe:/usr/sap/KXD/DVEBMGS04/exe:
-> exe path = PATH=/opt/java1.4/bin:/usr/sap/KXD/DVEBMGS04/j2ee/os_libs:/oracle/KXD/102_64/bin:/opt/java1.4/bin:.:/home/kxdadm:/usr/sap/KXD/SYS/exe/run:/usr/bin:/usr/ccs/bin:/usr/contrib/bin:/usr/contrib/Q4/bin:/opt/perl/bin:/opt/ipf/bin:/opt/nettladm/bin:/opt/fcms/bin:/opt/wbem/bin:/opt/wbem/sbin:/opt/sas/bin:/opt/graphics/common/bin:/opt/atok/bin:/usr/bin/X11:/usr/contrib/bin/X11:/opt/sec_mgmt/bastille/bin:/opt/caliper/bin:/opt/resmon/bin:/opt/drd/bin:/opt/dsau/bin:/opt/dsau/sbin:/opt/firefox:/opt/gnome/bin:/usr/contrib/kwdb/bin:/opt/mozilla:/opt/perl_32/bin:/opt/perl_64/bin:/opt/prm/bin:/opt/sfm/bin:/opt/swm/bin:/opt/sec_mgmt/spc/bin:/opt/ssh/bin:/opt/sentinel/bin:/opt/swa/bin:/opt/hpsmh/bin:/opt/thunderbird:/opt/langtools/bin:/opt/gwlm/bin:/opt/ignite/bin:/opt/cfg2html
[Thr 1] Wed Mar 25 16:03:40 2009
[Thr 1] JStartupICreateProcess: fork process (pid 22530)
[Thr 1] JControlICheckProcessList: process server0 started (PID:22530) -
CPIC return code 017, SAP return code 236
We get the following error in our SM21 log production system as
"Communication error, CPIC return code 017, SAP return code 236
> CPI-C function: CMINIT(SAP)"
Please let me know if anybody has ever faced it?Hi
Check these links
[236,,No connection to gateway ???]
[Gateway Connection Failure RC=236]
Also is your Kernel updated?
Regards
Puneeth
Edited by: Puneeth on Jul 10, 2009 3:10 PM -
Comminication Error - CPIC ret code 020, Sap ret code 223
Hi All,
Our SAP system receives inbound IDOCS from an external system (throgh TIBCO),
i have configured inbound partner profile in WE20,
There is now a problem in sending IDOCS to SAP. (Communication error CPIC code 020, SAP code 223).
Has anyone experienced similar problems - maybe point us in the right place to correct problem:
I have copied the text from the system log entries:
A CPIC function has failed. The conversation ID and CPIC function are
specified in the system log entries. Use the conversion ID to find more
detailed information about the error in the system log for the SAP
gateway.
Meaning of the SAP return codes:
1) Gateway errors:
221,,Error in CPIC-SS
222,,Storage bottleneck
223,,Network read error
224,,Network write error
225,,Invalid request
226,,No connection yet
227,,Gateway process terminated
228,,Shared-Memory problem(read)
229,,Shared Memory problem(write)
230,,No free LU
231,,No free gateway process
232,,Error when starting gateway proc.
501 ,,CMRCV failed.
i did't understand where the actual problem?
Regards,
Suresh.DHi,
this might be temporal connection issue.
Could you please have a look to SAP Note 421558.
Read SAP Note 63347 - List: CPIC error codes
Regds, -
Error in Cost Estimate through SAP t code CK11n
Dear All,
we are encountering a problem in the Production server with regards to the costing of the finished goods materials u201CFERTu201D, when cost estimate is ran through CK11N, the system pick up standard price maintianed in material master of Raw material.
please note that we valuate our raw material on MAP and price control indicator V has been maintained for all raw materials
our material are coming form our BOM and procurement type F has been maintained in MRP view
We also want to share that before executing the cost estimate we updated moving average price through t code MR21 ( as at the time of GRN of these raw materails, moving average price was disturbed due to wrong per unit price entered in PO by one end user)
we have throughly examined configuration for standard cost estimate of material with Qunatity structure.it is ok from all respect, if we execute costing run for same material in Developemnt server, cost estmate is executing accuratley by picking MAP price. the differnce of the step between dev and production server is to update prices through MR21
Immediate reply is highly appreciated----please adviceDear Pradeep,
in our case , strategy sequence in valuation variant is "Valuation price according to price control in material master " and then is "standard price"
in accounting view of material master we have maintained price control indicator "v" i.e MAP
i once again do inform that results of cost estimate is accurate if i execute in my Dev server i,e raw materials are being costed at MAP
plz advcie -
Document control failed due to error in [DOCMGR-CANCEL] with a return code
i am getting this error while calceling the purchase order "Document control failed due to error in [DOCMGR-CANCEL] with a return code of [OTHER]. "
I am doing the calcel like this
Nav: buyer work centre --> order
searche the po and then
select order --> cancel then click GO button
i gave the Reason as Cancel
communication method: email
Cancel Requisition: Yes
Please help on this, its urgent.
Thanks,
Vijay.Hi Vijay,
Check this MOS note.
Cancelling A Standard Purchase Order In Buyer Work Center Results In Error [Docmgr-Cancel] With A Return Code [ID 1338826.1]
Thanks
-Arif. -
HI. I just got a new macbook pro 15".
every time i launch garageband i get this message
"Error code 28773 was returned by the Audio driver."
when i hit record, the shaded area in GB starts to advance, but it doesn't record any sound, and when i hit the space bar, the recorded area disappears.
anyone know how to fix this?
I have installed BOOM, but i think that's the only extra sound software i have.]
PLEASE HELP!
thanks,
mojoman22Please read this whole message carefully, especially the warnings, before doing anything.
1. The changes to your configuration suggested here should be considered provisional; they may not solve your problem, or they may remove functionality that you find useful. If a third-party system modification that you want to keep is causing the problem, seek help from its developer.
2. WARNING: Back up all data now if you haven’t already done so. Before proceeding, you must be sure you can restore your system to its present state, even if it becomes unbootable. If you’re not sure you can do that, STOP — DON’T CHANGE ANYTHING. If you’re dissatisfied with the results of the procedure suggested below, restore from your backup. I will not be responsible for the consequences, and I will not be able to help, if you ignore this warning.
3. You should either remove or update the following system modification(s), if an update is available from the developer:
Parallels
and definitely remove at least the following:
Boom
† MacKeeper
† VirusBarrier
4. Whatever you remove must be removed completely, and (unless otherwise specified in this message) the only way to do that is to use the uninstallation tool, if any, provided by the third-party developers, or to follow their instructions. If the software has been incompletely removed, you may have to re-download or even reinstall it in order to finish the job. I can't be more specific, because I don't install such things myself. Please do your own research.
Here are some general guidelines to get you started. Suppose you want to remove something called “BrickYourMac.” First, consult the product's Help menu, if there is one, for instructions. Finding none there, look on the developer's website, say www.brickyourmac.com. (That may not be the actual name of the site; if necessary, search the web for the product name.) If you don’t find anything on the website or in your search, email the developer. While you're waiting for a response, download BrickYourMac.dmg and open it. There may be an application in there such as “Uninstall BrickYourMac.” If not, open “BrickYourMac.pkg” and look for an Uninstall button.
Again, please don't ask me to do this research for you. You can do it better than I can, because I haven't installed the product and I may not even know what it is.
If you can’t remove software in any other way, you’ll have to erase your boot volume and perform a clean reinstallation of OS X. Never install any third-party software unless you're sure you know how to uninstall it; otherwise you may create problems that are very hard to solve.
WARNING: Trying to remove complex system modifications by hunting for files by name often will not work and may make the problem worse. The same goes for "utilities" that purport to remove software.
5. I recommend that you never reinstall the modifications marked with a dagger (†) above, if any. If your problem is resolved after uninstalling all the above modifications and rebooting, but you still want to use some of those not marked with a dagger, you can experiment with putting them back, one at a time, testing carefully after each step. Keep in mind that system modifications may be incompatible with each other or with future OS X updates, so it may not be clear which one is at fault.
6. If you still have problems after making the suggested changes and rebooting, post again. Remember: if you don’t like the results of this procedure, you can undo it by restoring from the last backup you made before you started.
Remove the "MacKeeper" crapware as follows.
Note: These instructions apply to the version of the product that I downloaded and tested in early 2012. I can't be sure that they apply to other versions, nor do I intend to repeat the test.
IMPORTANT: "MacKeeper" has what the developer calls an “encryption” feature. In my tests, I didn't try to verify what this feature really does. If you used it to “encrypt” any of your files, “decrypt” them before you uninstall, or (preferably) restore the files from backups made before they were “encrypted.” As the developer is not trustworthy, you should assume that the "decrypted" files are corrupt unless proven otherwise.
In the Finder, select Go ▹ Applications from the menu bar, or press the key combination shift-command-A. The "MacKeeper" application is in the folder that opens. Quit it if it's running, then drag it to the Trash. A dialog will pop up asking why you want to uninstall it. You don't have to provide that information. Enter anything you like in the text box, then click the Uninstall button. All the functional components of the software will be deleted. That's the only useful feature of "MacKeeper:" it deletes itself. Reboot.
Do not try to uninstall by dragging the MacKeeper icon in the Dock or the LaunchPad to the Trash.
Here are some general suggestions. If you want your computer to be usable, don't install crapware, such as “themes,” "haxies," “add-ons,” “toolbars,” “enhancers," “optimizers,” “accelerators,” “extenders,” “cleaners,” “defragmenters,” “firewalls,” "barriers," “guardians,” “defenders,” “protectors,” most “plugins,” commercial "virus scanners,” "disk tools," or "utilities." With very few exceptions, this kind of material is useless, or worse than useless.
The more actively promoted the product, the more likely it is to be garbage. The most extreme example is the “MacKeeper” scam.
The only software you should install is that which directly enables you to do the things you use a computer for — such as creating, communicating, and playing — and does not modify the way other software works. Never install any third-party software unless you know how to uninstall it. -
Error for COM Routine application program (return code 40028)
Hi,
When we loading data in Planning Book ,we are getting below error
Error for COM Routine application program (return code 40028)Hi,
Did you try checking your COM build? The COM communicates between your database and Livecache and fetches the data requested. The last time we had this, SAP recommended COM upgrade.
Maybe you are looking for
-
Windows reboots immediately when I start iTunes
The Problem: When I click on the iTunes icon to start up the software, my computer restarts IMMEDIATELY. There is no error message, the computer does not freeze, and there is no indication that an iTunes window opened at all, even briefly. The screen
-
3GS phone is stuck on "connect to iTunes" graphic, iTunes doesn't recognize it
During IOS 5 upgade process, after iTunes performed backup and wipe, screen went to "connect to iTunes" graphic, however, iTunes will not recognize it. I can't perform a restore until I can get iTunes to recognize it. Can someone give me detailed d
-
When I attempt to convert a pdf file to a word file it does not let me and I am re-directed to the purchase page. I already paid for this service and It will not let me convert. What is going on here ?
-
The cover art is missing on my playlists songs, but not for songs in the cloud on my iphone 5s
Ever since I updated to iOS 8, not 8.0.2 (still haven't done that update), the artwork on my music is missing for any songs that are on my phone and in my playlists. My music that is stored in the cloud still has its cover art. All of the songs still
-
Enrolling iOS devices "not shown in Configuration Manager console"
After successfully enrolled my Windows RT I want to enroll my iOS devices (iPad 1 & iPhone 4). First step is completing the iOS configuration (uploading APN certificate). Next step I associated my devices by installing management profiles (https://ma