Como configurar SPA941 no Cisco Unified 500 Series - UC500

Comprei Um UC 500 mas não consigo configurar aparelhos do Modelo SPA 941, no modelo SPA502G configura corretamete, verifiquei que tem como fazer upload de outros modelos de telefone mas não encontro em lugar algum, alquem tem ideia onde posso encontrar, configurar esses aparelhos 941 ?

You have to look for "third party SIP phone" examples, as there is no direct support for SPA 9xx in UC500.

Similar Messages

Connecting two cisco ESW 500 series switches.

Hi Experts,
I have a basic knowledge of network and need some help.
I have two cisco ESW 500 series switches and i want to connect them together.
Q1 # Which type of cable i should use to connect these two switches CrossOver or fiber...What is the advantage of using Fiber over CrossOver. ?
Q2 # What are the marked ports in the image used for...???

tech spec,
Traditionally you would use crossover to connect switches. Most modern network devices have Auto-MDIX which allows the device to connect using either crossover or straight through.
The ports on the right can be used for uplink or as regular network ports. On the 10/100 versions the ports on the right are usually Gigabit, thus making them more suitable for uplink to another switch, etc.
Please mark this thread as answered or reply if you have any additional questions.
- Marty

How to erase all configuration in Cisco ESW 500 Series Switches

Hi anybody,
Anyone show me how to erase or remove configuration file from ESW 500 Series Switches?
Thanks
Thuc

Hi Thuc,
The restart / reset function will allow for local or remote reset of the the unit to Factory defaults, see screen capture below. ;
Alternatively, the Switch can be reset by inserting a paper clip into the RESET opening on the friont of the switch.
Pressing the manual reset for 0 to 10 seconds only reboots the switch.
Pressing the manual reset for longer than 10 seconds results in the switch being reset to factory defaults.
does this answer your question, not exactly sure it does ?
regards Dave

Cisco ISA 500 Series - Intervlan routing via 801.2q (Router on a stick)

Hello to everyone,
I am considering the ISA 550 for a customer who has multiple VLANs on his network. In order to avoid purchase a layer3 switch, I was thinking that we could perhaps create a 802.1q trunk link from a switch to the ISA500 and perform Inter-VLAN routing through that. In addition, we would use access lists to prevent communications between specific VLANs.
My question is if this setup model can be done on the ISA 550. I haven't used it before, so I am not sure if it can support this setup.
Any information or help is much appreciated.
Many thanks,
Chris.

Chris, ISA550 can support the configuration you described.

I want your valuabale opininon on ESW 500 series switches

In my offiec i want to connect 8 accesspoints and 8 smart boad and 8 pcs to a switch the access points are cisco 1240g series and controlled by a wlan controller.
this switch should be connected to a core switch 4507 using fiber.
can i use these esw switches for this

Not sure what you mean by 8 smart boad - can you be more clear on that?
Couple of comments:
- Please note that we recommend the ESW in a Cisco Small Business type deployment with products such as UC500, SR500, AP500. Also, management is via a configuration utility GUI or CCA, not CLI as you would use for the Cisco Catalyst switches. Check this discussion which has a PDF that goes over positioning of the switches- https://www.myciscocommunity.com/message/8385#8385
- Please check the POE requirements you need against the ESW switches - check the question on at Q & A
Q. How many devices can the Cisco ESW 500 Series PoE switches power?

Ask the Expert: C-Series Integration with Cisco Unified Computing System Manager

Welcome to the Cisco Support Community Ask the Expert conversation. This conversation is an opportunity to learn and ask questions about Cisco C-Series Integration with Cisco Unified Computing System® Manager (Cisco UCS® Manager) with Cisco experts Vishal Mehta and Manuel Velasco.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (Cisco IMC). When a C-Series rack-mount server is integrated with Cisco UCS Manager, the IMC no longer manages the server. Instead you will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager command-line interface (CLI).
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management. The following are the connectivity modes:
Dual-wire management (shared LAN On Motherboard [LOM]): Shared LOM ports on the rack server are used exclusively for carrying management traffic.A separate cable connected to one of the ports on the Payment Card Industry Express (PCIe) card carries the data traffic.
SingleConnect (Sideband): Using Network Controller Sideband Interface (NC-SI), the Cisco UCS Virtual Interface Card 1225 (VIC1225) connects one cable that can carry both data and management traffic.
Direct Connect Mode: Cisco UCS Manager Version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
Vishal Mehta is a customer support engineer for Cisco’s Data Center Server Virtualization Technical Assistance Center (TAC) team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco Nexus® 5000, Cisco UCS, Cisco Nexus 1000V, and virtualization. He presented at Cisco Live in Orlando 2013 and will present at Cisco Live Milan 2014 (BRKCOM-3003, BRKDCT-3444, and LABDCT-2333). He holds a master’s degree from Rutgers University in electrical and computer engineering and has CCIE® certification (number 37139) in routing and switching and service provider.
Manuel Velasco is a customer support engineer for Cisco’s Data Center Server Virtualization TAC team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco UCS, Cisco Nexus 1000V, and virtualization. Manuel holds a master’s degree in electrical engineering from California Polytechnic State University (Cal Poly) and CCNA® and VMware VCP certifications. Remember to use the rating system to let Vishal and Manuel know if you have received an adequate response.
Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation in the Data Center, under subcommunity, Unified Computing, shortly after the event. This event lasts through May 23, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Sebastian,
The different modes of connecting C-Series with UCSM come into play depending on the type of infrastructure you already have along with C-Series and NIC model.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (CIMC) .
Powerful features provided by Cisco UCS Manager can be leveraged to manage C-Series server by integrating C-Series Rack-Mount Server with UCSM.
This not only gives you rich-feature set but also one management plane to operate UCS-B Series Chassis and UCS-C Series Rack Server.
You will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager CLI.
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management.
The following are the connectivity modes:
• Dual-wire Management (Shared LOM):
Shared LAN on Motherboard (LOM) ports on the rack server are used exclusively for carrying management traffic. A separate cable connected to one of the ports on the PCIe card carries the data traffic. Using two separate cables for managing data traffic and management traffic is also referred to as dual-wire management.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0100.html
This mode is recommended when you have C-Server which does not have or cannot support VIC 1225 card (such C-200 server)
• SingleConnect (Sideband):
Using Network Controller Sideband Interface (NC-SI), Cisco UCS VIC1225 Virtual Interface Card (VIC) connects one cable that can carry both data traffic and management traffic.
This feature is referred to as SingleConnect.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_011.html
This most recommended Integration model when using FEX and VIC 1225 card
• Direct Connect Mode:
Cisco UCS Manager release version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
This mode will eliminate the need for FEX module as Servers are directly plugged into the base ports of Fabric Interconnect
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0110.html
Please let us know if you need more information. Thank you!
Thanks,
Vishal

Cisco 500 Series 802.1x Requirements

Hello,
Does anyone have a guide on how to setup 802.1x on the Cisco 500 Series Switches.
I have done the whole implamentation in the past with Catalysts and ACS.
But would like to see a guide for the 500 series.
Do we need the Cisco ACS or can we use RADIUS on Windows?

Hi Peter, you may use IAS or any radius you prefer. To my knowledge the admin guide is the only documentation. You may check the Cisco knowledgd base as well.

Cisco 500 series switches

Dear support,
Can Cisco 500 series switches deliver 24V on the access port for POE operation?
Best Regards

I belive the 802..2F and 802.2at poe standard is strictly 48v. I haven't found anything to the contrary. There are inline convertes 48v-24v or something like this that can be used with a non poe switch: http://www.digital-loggers.com/poe24.html but that means all conected device would be off the same access port / vlan.

Cisco 500 Series Fiber Optic connector issues

I have a 500 Series express with a Cisco GE SFP, LC connector SX transeiver and a belkin dual LC to ST cable plugged into it.
The unit is stating the cable is misconfigured. Is there anything I have to do besides configuring the port to switch in the smart role settings to get this fiber interface to work?

Hi
If you are getting any error logs in your switch is it possible for you to paste the same here ?
Also are you connecting your server on the SFP or any other device ..
regds

Como configurar airprint

como puedo configurar el air print en mi ipod

Hello Pepe Popa,
Thank you for contacting the Sales Acceleration Center (SAC) regarding your recent inquiry, Case Number 79432
Case Description:
como configurar cisco aironet 1200 series soy nuevo en esto por favor
Case Solution:
Please go thru this likns for configuration and samples that will help you with some configuration "Samples" for IOS base WAP's..
likk for Configuring the Access Point for the First Time
http://www.cisco.com/en/US/partner/docs/wireless/access_point/12.3_7_JA/configuration/guide/s37frst.html
Here is the link for configuration sample
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_installation_and_configuration_guides_list.html
If your access point still using VxWorks please use the following
http://www.cisco.com/en/US/partner/docs/wireless/access_point/1200/vxworks/configuration/guide/bkscgch4.html
As per your confirmation, I am going to close the case for this specific inquiry. We strive to provide you with excellent service. Please feel free to reach out to me or any member of the SAC team if we can be of any further assistance or if you have any other related questions in the future. We value your input and look forward to serving you moving forward.
Thank you,
Manuel Baez
Sales Specialist
Need help ? call Sales Acceleration Center(SAC) at Toll Free (USA) :1-800-225-0905 International +1-408-902-4872 or send email to [email protected] or Live Chat: http://tinyurl.com/sacucs

I need online Configuration Guide for Catalyst Express 500 Series Switches

Hi Mates,
Please is there an online help page for 500 series catalyst
I have this one for IOS 12.2(25)FY http://www.cisco.com/en/US/products/ps6545/products_configuration_example09186a00806da6c9.shtml
but I need more detailes like IOS 12.3(7)JA for Aironet 1300 http://www.cisco.com/en/US/products/ps5861/products_configuration_guide_book09186a00804ebd50.html
Regards
Saher

I'm afraid there is not such document for IOS 12.2(25)FY since the Catalyst Express 500 Series switches are manageable through the GUI Device Manager or Cisco Network Assistant.
I have also found key features and standards supported for that release:
http://www.cisco.com/en/US/products/sw/iosswrel/ps5012/prod_bulletin0900aecd8033b8b3.html
Hope this helps

Ask the Expert: Different Flavors and Design with vPC on Cisco Nexus 5000 Series Switches

Welcome to the Cisco® Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about Cisco® NX-OS.
The biggest limitation to a classic port channel communication is that the port channel operates only between two devices. To overcome this limitation, Cisco NX-OS has a technology called virtual port channel (vPC). A pair of switches acting as a vPC peer endpoint looks like a single logical entity to port channel attached devices. The two devices that act as the logical port channel endpoint are actually two separate devices. This setup has the benefits of hardware redundancy combined with the benefits offered by a port channel, for example, loop management.
vPC technology is the main factor for success of Cisco Nexus® data center switches such as the Cisco Nexus 5000 Series, Nexus 7000 Series, and Nexus 2000 Series Switches.
This event is focused on discussing all possible types of vPC along-with best practices, failure scenarios, Cisco Technical Assistance Center (TAC) recommendations and troubleshooting
Vishal Mehta is a customer support engineer for the Cisco Data Center Server Virtualization Technical Assistance Center (TAC) team based in San Jose, California. He has been working in TAC for the past 3 years with a primary focus on data center technologies, such as the Cisco Nexus 5000 Series Switches, Cisco Unified Computing System™ (Cisco UCS®), Cisco Nexus 1000V Switch, and virtualization. He presented at Cisco Live in Orlando 2013 and will present at Cisco Live Milan 2014 (BRKCOM-3003, BRKDCT-3444, and LABDCT-2333). He holds a master’s degree from Rutgers University in electrical and computer engineering and has CCIE® certification (number 37139) in routing and switching, and service provider.
Nimit Pathak is a customer support engineer for the Cisco Data Center Server Virtualization TAC team based in San Jose, California, with primary focus on data center technologies, such as Cisco UCS, the Cisco Nexus 1000v Switch, and virtualization. Nimit holds a master's degree in electrical engineering from Bridgeport University, has CCNA® and CCNP® Nimit is also working on a Cisco data center CCIE® certification While also pursuing an MBA degree from Santa Clara University.
Remember to use the rating system to let Vishal and Nimit know if you have received an adequate response.
Because of the volume expected during this event, Vishal and Nimit might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure Community, under the subcommunity LAN, Switching & Routing, shortly after the event. This event lasts through August 29, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Gustavo
Please see my responses to your questions:
Yes almost all routing protocols use Multicast to establish adjacencies. We are dealing with two different type of traffic –Control Plane and Data Plane.
Control Plane: To establish Routing adjacency, the first packet (hello) is punted to CPU. So in the case of triangle routed VPC topology as specified on the Operations Guide Link, multicast for routing adjacencies will work. The hellos packets will be exchanged across all 3 routers and adjacency will be formed over VPC links
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/operations/n5k_L3_w_vpc_5500platform.html#wp999181
Now for Data Plane we have two types of traffic – Unicast and Multicast.
The Unicast traffic will not have any forwarding issues, but because the Layer 3 ECMP and port channel run independent hash calculations there is a possibility that when the Layer 3 ECMP chooses N5k-1 as the Layer 3 next hop for a destination address while the port channel hashing chooses the physical link toward N5k-2. In this scenario,N5k-2 receives packets from R with the N5k-1 MAC as the destination MAC.
Sending traffic over the peer-link to the correct gateway is acceptable for data forwarding, but it is suboptimal because it makes traffic cross the peer link when the traffic could be routed directly.
For that topology, Multicast Traffic might have complete traffic loss due to the fact that when a PIM router is connected to Cisco Nexus 5500 Platform switches in a vPC topology, the PIM join messages are received only by one switch. The multicast data might be received by the other switch.
The Loop avoidance works little different across Nexus 5000 and Nexus 7000.
Similarity: For both products, loop avoidance is possible due to VSL bit
The VSL bit is set in the DBUS header internal to the Nexus.
It is not something that is set in the ethernet packet that can be identified. The VSL bit is set on the port asic for the port used for the vPC peer link, so if you have Nexus A and Nexus B configured for vPC and a packet leaves Nexus A towards Nexus B, Nexus B will set the VSL bit on the ingress port ASIC. This is not something that would traverse the peer link.
This mechanism is used for loop prevention within the chassis.
The idea being that if the port came in the peer link from the vPC peer, the system makes the assumption that the vPC peer would have forwarded this packet out the vPC-enabled port-channels towards the end device, so the egress vpc interface's port-asic will filter the packet on egress.
Differences: In Nexus 5000 when it has to do L3-to-L2 lookup for forwarding traffic, the VSL bit is cleared and so the traffic is not dropped as compared to Nexus 7000 and Nexus 3000.
It still does loop prevention but the L3-to-L2 lookup is different in Nexus 5000 and Nexus 7000.
For more details please see below presentation:
https://supportforums.cisco.com/sites/default/files/session_14-_nexus.pdf
DCI Scenario: If 2 pairs are of Nexus 5000 then separation of L3/L2 links is not needed.
But in most scenarios I have seen pair of Nexus 5000 with pair of Nexus 7000 over DCI or 2 pairs of Nexus 7000 over DCI. If Nexus 7000 are used then L3 and L2 links are required for sure as mentioned on above presentation link.
Let us know if you have further questions.
Thanks,
Vishal

Cisco Aironet 1310 series

hello all,
I have a cisco Aironet 1310 series which am having problem with the signal strength. This box came with 8 dbi Omni antenna gain and am told this can go upto 5km raduis. After configuring this equipment, i could not get a link when i move 500 meters. Please find attached the configs on the box. Any help given would be very much appreciated. Thank You

This 5KM distance is only going to be applicable in bridging situations. The following link shows how to use the distance calculations based on devices: http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
In theory, if you had a really strong direction antenna on your client you'd be able to get the 1310 as an access Point from 5km, but you'd need perfect line-of-site and you wouldn't be mobile...
As others had mentioned, if you're looking for an access point situation with that kind of range, then you need WiMax....
but if it is bridging you want, its just a matter of getting the other link to see this one (with a good enough antenna)

Catalyst 500 series

hi,
i have a question regarding cisco 500 series switches and it is that if we want to shut down this switch remotely then is it possible or it has to be done manually by going to the switch location and disconnecting the power supply because i dont see a power off or shut down option if it is accessed remotely like from a pc.
regards
Ahmed

I don't think many devices are meant to be shutdown. As soon as there is power they run. That's what they are made for.
What do you wish to acomplish with the shutdown?
Cheers,
Michel

Camera for use with Cisco Unified Video advantage?

Cisco is EOLing the Cisco Unified video advantage product that we thought would be a good fit for us to integrate video with some of our IP Phones. I can still order the Video Advantage software until later in the year from Cisco but they have discontinued the Cisco VT Camera III that was previously used with this product.
They list the Logitech C920-C web cam as a replacement for this product, but it seems to be difficult to locate. The realease notes say you can use a 3rd party camera but Cisco does not officially support it.
Has anyone used any third party cameras with Cisco Unified Video advantage and if so which would you recomend. I was hoping to use the Logitech HD Pro Webcam C920 (the generic non Cisco version) but wasn't sure if it would work ok?
What do you think? This will be using Unified Video Advantage 2.3.
Jim

Hi,
We have been using Video advantage v 2.1.2 with 7940 series phone since long, it works fine with almost all 3rd party camera`s and even with the inbuilt laptop cameras.
v 2.3 is an enhanced version as compared the one which we are using. So i would suggest you to go ahead and try it with any good qaulity webcameras available in market.
Further to add there are certain PC requirements which needs to be met, the same can be found in the below link.
http://www.cisco.com/en/US/docs/video/cuva/2_3/release/notes/relnote_cuva23.html#wp1118706

Como configurar SPA941 no Cisco Unified 500 Series - UC500

Similar Messages

Maybe you are looking for