Compaq/HP CCISS controller and Grub/Lilo

I have this big problem.
I have just installed Arch 64 bit on a brand new HP DL380. No problem there.
When I got to installing the boot loader, unsurprisingly I had a problem installing Grub, so used LILO instead.
This was fine until I did an update when Lilo changed its mind about what the root device was (/dev/cciss/c0d0p3) and decided it must be /dev/cciss!c0d0p3.
Needless to say there is no such partition.
After a bit of a struggle I did get Grub to replace lilo and it boots in to grub fine, the only problem is that that is as far as it gets. It does not appear to see or load the menu at /boot/grub/menu.lst, so I have to type in the options followed by boot and it boots. This is obviously not good.
Has any one got any ideas?
For example can they tell what I may be missing in the grub setup?
Kind regards
Benedict White

I just reinstalled the machine via FTP, and what I found was that when I tried to install grub, a very quick error popped up saying that there was a divide by zero error and mentioning the CCISS controller. Anyone any ideas where I can look at the script responsible?

Similar Messages

Multimedia Audio Controller, and Video Controller(VGA compatible) are missing on Windows XP(32Bit) SP3

Hi.
My Desktop Computer(Intel P 4, 512MB of RAM, and Graphics Card with 256MB of RAM)
Also, My Desktop Computer with P 4 doesn't have any access internet since there is no network adapter is installed. As a result, I would not be able to run the pc scan utility, or Reader a web-based applet that identifies my GPU or Audio controller
and finds the latest graphics driver for my GPU, and Audio.
I have two Windows XP installations:
Windows XP SP2(32Bit) which is old and it seems it infected by some viruses.
I have installed another fresh clean Windows XP(32Bit) SP3. However, I have two devices not detected well by Windows XP.
First of all, when saying that I have multi-operationgs systems, I mean there are two operating systems installed on my PC(SP2, SP3) both are 32Bit. The first Windows SP2(NOT installed by me) has all multimedia audio card installed well,
and has SCSI and RAID Host Controller shown the device manager. However, only the VGA is not installed on Windows SP2. However, the second one Windows SP3(Installed by me) has VGA not installed, Multimedia audio NOT installed, and there is no SCSI and RAID
Host Controller in device manager.
First: Yes, my motherboard has integrated video, and integrated audio card
According to the screen shots above, then
The vendor ID of Multimedia Audio Controller is 8086 and the device ID is
24D5.
The vendor ID of Video Controller is 8086 and the device ID is
2572.
I AM EXPECTING THAT KNOWING THE VENDOR ID AND THE DEVICE ID WILL LET ME QUICKLY FIND THE APPROPRIATE DRIVER. HOWEVER, I COULDN'T FIND THE APPROPRIATE DRIVER.
Thus, could you please help me to find them?
I have tried installing a soundMAX card driver, however, I found this error.
I have checked the other Windows XP SP2(32Bit) which is oder installed, and it seems it infected by some viruses.
However, the Multimedia Audio on that Windows is installed well. As here: I only posted these screen shots to show what kind of device is Multimedia Audio Card
The motherboard model is:
Belarc Advisor Computer Profile
Operating
System
System
Model
Windows XP Professional
Service Pack 3 (build 2600)
Install Language: English (United
States)
System Locale: Arabic (Yemen)
Installed: 22/03/2013 12:03:16
ص
Boot Mode: BIOS (Secure
Boot not supported)
Enclosure Type:
Desktop
Processor
a
Main Circuit Board
b
3.00 gigahertz Intel Pentium
4
16 kilobyte primary memory cache
1024 kilobyte secondary memory
cache
64-bit ready
Hyper-threaded (2 total)
Board: 775i65G.
Bus
Clock: 200 megahertz
BIOS: American Megatrends Inc. P3.00
03/20/2007
Drives
Memory Modules
c,d
39.99 Gigabytes
Usable Hard Drive Capacity
29.48 Gigabytes Hard Drive Free
Space
COMPAQ CD-ROM LTN486S [Optical drive]
3.5" format removeable
media [Floppy drive]
WDC WD400BB-75DEA0 [Hard drive] (40.00 GB) -- drive
0, rev 05.03E05, SMART Status:
Healthy
504 Megabytes Usable
Installed Memory
Slot 'DIMM0' has 512 MB
Slot 'DIMM1' is
Empty
Local Drive
Volumes
c: (NTFS on drive 0) *
20.98 GB
14.16 GB free
d: (NTFS on drive 0)
19.01 GB
15.33 GB free
<center>
* Operating System is installed on
c:
</center>
Network
Drives
None
discovered
Users
(mouse over user name for details)
Printers
local user
accounts
last logon
عايض
لرضي
19/01/2015 10:59:17 م
(admin)
local system
accounts
Administrator
never
(admin)
Guest
never
HelpAssistant
never
SUPPORT_388945a0
never
<center>Marks
a disabled account; Marks
a locked account </center>
Controllers
Display
Standard floppy disk
controller
Intel(R) 82801EB Ultra ATA Storage Controllers
Primary IDE
Channel [Controller]
Secondary IDE Channel [Controller]
None
discovered
Bus
Adapters
Multimedia
Intel(R) 82801EB USB
Universal Host Controller - 24D2
Intel(R) 82801EB USB Universal Host
Controller - 24D4
Intel(R) 82801EB USB Universal Host Controller -
24D7
Intel(R) 82801EB USB Universal Host Controller - 24DE
Intel(R)
82801EB USB2 Enhanced Host Controller - 24DD
None
discovered
Virus
Protection [Back to Top]
Group
Policies
Norton AntiVirus Version 18.1.0.37
 Virus Definitions Version Not Up To Date
 Realtime File Scanning
On
None
discovered
Communications
Other
Devices
↓ Realtek RTL8139 Family PCI Fast
Ethernet NIC
Status:
Cable unplugged
Dhcp Server:
none responded
Physical Address:
00:19:66:1F:F7:54
USB Human Interface
Device
Standard 101/102-Key or Microsoft Natural PS/2
Keyboard
HID-compliant mouse
USB Root Hub (5x)
USB Storage Use in past 30 Days(mouse
over last used for details)
Hosted Virtual Machines (mouse over
name for details)
Last
Used
SanDisk Cruzer Blade, s/n
4C532000020502112303, rev 2.01
19/01/2015
09:32:57 م*
USB 2.0 USB Flash Drive, s/n
59309e92e21612, rev 0.00
09/01/2015
12:29:17 ص*
<center>* Possibly used again before the reboot following this
time.</center>
None
discovered
See your entire
network map...
click for Belarc's System Management products
A man should convert his anger and sadness into strength to continue living in this life.

Dont worry, dont think anyone was as a matter of fact
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=908&jump= true#M908
http://support.microsoft.com/default.aspx?scid=kb;en-us;80509
http://support.microsoft.com/default.aspx?scid=kb;en-us;84567
that worked for me, maybe it will help someone else that went through what i did, its a miracle i did not top myself after going through all this BS. ALSO dont threaten your computer with violence, cos it will always call your bluff which makes things worse

Boot Loader Problem(rEFIt & GRUB/LILO)

Hi,
I'm planning to "triple boot" my iMac with "Mac SL, Win 7, & openSUSE". But installing the "GRUB/LILO" makes my origanel boot loader rEFIt cannot work directly.
I have to select "Win 7/openSUSE" from the rEFIt, and select "WIn 7/openSUSE" again (from GRUB/LILO).
Any suggestion for fixing the problerm so I can boot straight to the OSes?
Thanks.

Boot from the solaris dvd in to singe user mode, mount the system under /a and run the instalgrub command in the shell:
/sbin/installgrub -m /boot/grub/stage1 /boot/grub/stage2 /dev/rdsk/c?d?s? (whatever your drive is).
Maybe make a backup copy of /a/boot/grub/menu.lst, I cant remember if it gets over written that way you can copy it back if necessary.

Compaq SmartArray 4200 controller

Hi, I tried to install Solaris 10 on a old Compaq Proliant 8500 with a Compaq SmartArray 4200 controller, but (using Solaris 8 drivers) the controller and the raid are not detected. Anyone know if is possible to install Solaris on this hardware?
Thanks in advance,
Stefano

Looks like the drivers used are not compatible... Please provide with the further details.

D20 Blue Screen loading Windows 7-64bit using Intel controller and Marvell enabled

Hi, Help,
Hardware:
D20, 4158, Four 500GB Seagate SATA drives configured as a RAID10 1TB virtual disk (partitioned into five logical drives).
Goal:
Recover or repair a degraded RAID array.
I want to be able to launch Windows 7-64bit using the Intel controller and have it access the virtual disk of the degraded RAID array attached to the Marvell controller. Subsequently, I want to use the Marvell MRU utility to repair/recover the situation.
Situation/Issue:
Things ran well for two years and two months until yesterday. Now, when booting I see:
1962: No operating system found. Press F1 to repeat boot sequence.
If I use the Windows 7 installation CD and load the Marvell driver, the attempt to recover the operating system reports that the MBR is corrupt and cannot be repaired.
If I boot with the Marvell controller disabled in the D20 BIOS, using a Windows 7 installation (with Marvell drivers) attached to the Intel controller, everything works except (of course) I cannot access the RAID drives.
If I reboot with the Marvell controller enabled, using the same Windows 7 installation via Intel controller, I see a "Starting Windows" announcement followed by a flash of the blue screen of death.
The BSOD message is unspecific, no error code, just...
"A problem has been detected and Windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this Stop error screen,
restart your computer..."
Additional information:
If I access the Marvell BIOS (ctrl-M) and look at Devices, one of the four Seagate drives has status FREE instead of status ASSIGNED. If I run the Marvell BIOS verify disk utility diagnosic on that FREE status disk, I get a fault error after about 30 minutes of scanning. So, one Seagate disk is sour and somehow the MBR was corrupted at the same time.
History:
Two years ago, during the intial configuration, I could access the Marvell RAID disks from this Intel-controller-booted Windows 7 installation, but my fuzzy memory is that I had to change something in the D20 BIOS, such as the AHCI setting or similar.
Status:
Today, using the Intel controller to boot Windows 7 with the Marvell controller enabled is just BSOD. What am I missing or failing to do or set?
Thank you in advance for any help and ideas.
-John
Solved!
Go to Solution.

Update:
I replaced the 500GB Seagate disk with a new 500GB Seagate. I ran the Marvell BIOS verify disk utility on the new disk drive and it passed with no errors. Following the steps given in the Marvell MRU online help, I rebuilt the virtual disk. Upon completion (which took a little more than an hour to complete), I rebooted. Before the Seagate disk went south yesterday, the Marvell virtual disk contained one primary partition (C, and four NTFS drives (D:, E:, F:, and Z. Now it contains three primary NTFS drives (C:, F:, and Z. An extended partition contains D: (an unformatted volume of size 199.30MB) and an unused space of 199.30GB.
Event log:
Looking at the event log, Windows reports that the disk in question raised a warning yesterday. Three messages share the same timestamp (all from mv64xx (a Marvell process):
"Physical disk 16 is plugged out."
"Virtual disk 0 is degraded."
"Physical disk 16 is plugged in."
Eight seconds later, UserPnp logs:
"Driver Management has concluded the process to add Service disk for Device Instance ID SCSI\DISK&VEN_SEAGATE&PROD_ST3500418AS&REV_CC38\5&248BBE23&0&000100 with the following status: 0"
One second later, UserPnp logs:
"Driver Management concluded the process to install driver FileRepository\disk.inf_amd64_neutral_10ce25bbc5a9cc43\disk.inf for Device Instance ID SCSI\DISK&VEN_SEAGATE&PROD_ST3500418AS&REV_CC38\5&248BBE23&0&000100 with the following status: 0x0."
Questions:
Is it possible that UserPnp corrupted the Marvell virtual disk after an intermittent physical disk unplugged/plugged-in event that happened when the Seagate hardware went failed. It looks to me like my D: and E: are toast despite RAID 10.
Any ideas? Is there anyway to recover the Marvell virtual disk configuration to the state prior to the hardware failure? If not, what good is RAID 10?
My apologies for the long posting, but I am an old software guy who does not understand the intricacies of RAID and disk management.
Thank you in advance for any leads toward a solution,
-John

Upgrading Controller and AP Help

I'm planning on moving from 4.1.185 to 4.2.130 tomorrow late but am having an issue in testing. My original plan was with 3 4404's and one of them being emtpy, have the 3rd running 4.2.130 and just move AP's from one of the older controllers over to it until it was empty. However that doesn't seem to be working. In WCS, my test AP is registered to Controller 1, I set it's primary to Controller 3 and it doesn't do anything. How can I force AP's over to the controller with the new code so they'll get updated? The reason for this is I can't take down the whole Hospital for a period of time while I upgrade a controller and wait (and hope) all of the AP's come back up over a period of time.

First verify that the mobility groups is confiugred with all the mac and ip address of all 3 WLC's. Make sure you can mping from one controller to antoher. Then what you can do is change the name of the primary controller to that of the new upgraded WLC. Now you can either enable ap fallback on the wlc that the ap is on or reset the ap, so when it boots back up it will try to join the new wlc.

Creating Planned orders and Requisitions for a particular MRP controller and for all the others only Requisition is to be created.

Hi Experts,
Currently we run Program 'RMMRP000' as a batch job to create Planned orders and requisitions.
The client wants that Planned orders and Requisitions should be created for a particular MRP controller and for all the others only Requisition is to be created.
I implemented Exit 'EXIT_SAPMM61X_001' in the following manner by passing MRP controller to user_key.
IF mt61d-dispo <> user_key.
no_planning = 'X'.
ENDIF.
But as you can see that this will not meet my client requirement.
If any of you has worked on similar requirement / if any one knows that this is achievable or not,
please share your inputs.

Moved from SAP ERP Sales and Distribution (SAP SD) to ABAP Development
G. Lakshmipathi

How do you create an installer/bundle for PPro with extension, a plugin (export-controller) and some

Hi
As my topic says
How do you create an installer/bundle for PPro with extension, a plugin (export-controller) and some custom presets?
Assume you have Flash Builder 4.5, CS Extension builder 2.0, Xcode 4.5.1 running under MacOS 10.8.

I understand why you need updated running headers in your book. To a sighted reader these serve as a guide to where you are and help you find things quickly. In addition, if you are exporting your data to XML or HTML from the tagged PDF it would also be important to have these in the proper location.
But for accessibility purposes, it doesn't have to be there because the screen reader reads everything in linear order, line by line. No one is looking at the page. A user listening to the screen reader read the page is going to hear this heading, just before the actual word itself. So they will hear the first word on the page twice. It's not the end of the world if it's there, but such headings are not necessary for accessibility unless they are not repetitive and contain information that is not otherwise available.
So I would say, fine if you need them or want them there, it's just one word.
I think you should try exporting your book to PDF (or even just a chapter of the book) and look at the tags panel in Acrobat to see if you are getting the result you want. I can't tell you exactly what you should do to get those results, you are using a plug-in I don't have.
I can tell you I didn't have to add the headers to any article at all, they just automatically export if the other articles in the file are added and you don't select the header style option "not for export as XML."
You may not experience the same results with your plug-in, but I think it will probably work the same way.
Give it a try and best of luck.

Problems with Ethernet controller and PCI device driver on Satellite L30-10X

Hellow!
Sorry for my bad English, I'm from Russia.
Just few days ago I bought Satellite L30-10X with W Vista on board. My opinion, that this OS does't very good on this computer, so I install W XP.
I have some problems with drivers. At first, I dont know what model I have:PSL30 or PSL33? I download all drivers for both models. But, after installation, computer doen't find drivers for Ethernet controller and PCI device...

Hi
Satellite L30-10X belongs to the PSL33E series. This number can be found on the label placed on the bottom of the unit!
You have to choose this number from the driver download form to get the compatible XP drivers.
I dont know why you are not able to install the LAN driver. Ive got the same notebook with Vista and Ive installed the XP and all drivers run fine.
I assume you have installed the drivers in wrong order. Please take the look in the Toshiba installation instruction txt file. In this order you have to install the driver! Its important.
I think you should install the XP again to ensure the clean registry and then download and install the compatible XP drivers like mentioned in the installation instruction file.
Good luck

Diff between Component controller,Custome controller and View controller

hi,
Can any body tell me the following details,
1.difference between the Component controller,Custome controller and View controller in WD-ABAP.?
2.what is Lead Selection?
Regards,
Ravi

Hi Ravi.
The component controller is visbile to all views in a component. So all context nodes and methods you create here can be accessed from all views in the component. This way you can share data between the views by mapping context nodes or thru method calls. You can also mark methods and nodes as interface so that they are acessable from other components that define component usages to this cmponent.
Custom controller is quiet similar to the component controller. You can define it if you want to group some views with a custom controller for a certain functionality.
If you want to access a custom controller in a view you have to define the usage first on the properties tab of the view.
A view controller is only visible in the view itself. So all methods or context nodes you define here are only accesable by the current view.
The lead selection is in most cases the current selected element in a context node. The lead selection is used by many UI elements to determine which element has to be shown (e.g drop down).
If you have a table with single selection the current selected table row is the lead selection element of the bound context node.
SO you can get the lead selection element easily in any mthod by calling context_node->get_element( ).
Hope this clears your questions.
Cheers,
Sascha

How to perform datalogging in a file using RT controller and a host PC?

I'm Using PXI-8145RT Controller and a Host PC(Dell Laptop),I used the TCP/IP DAQ Vi's but Im getting problems in logging data into a file at the Host using the Vi's .For 3 Channels the program works fine but as I increase the Number of Channels the program stops running on the RT Controller! Do we have to configure some TCP/IP settings for this or i have to use some other methods for datalogging into a file on the host using an RT Controller on the ethernet.

If you increase the number of channels and the RT program stops running, it could be that your scan rate is too fast for the increased number of channels on the 8145. First try to lower your scan rate by a large amount (a factor of 10, for example) to see if this is the problem. If you still see the same behavior when going above 3 channels of input, I would suggest looking at the following links for more information on communication with RT.
General Communication Info:
NI Developer Zone: Communicating with a Real-Time Engine
Specific Documents:
NI Developer Zone: Real-Time FIFO for Deterministic Data Transfer Between VIs
NI Developer Zone: TCP/IP between the Host PC and Real-Time Series Hardware
Furthermore, if you are using LabVIEW RT 7.0, I would highly suggest the use of the RT Communication Wizard. It will create the communication portion of your RT application for you.

Problems between a Wireless Controller and a Switch.

I have a Wireless Controller 4402 connected to one sw2960G.
I configured the controller with LAG and the switch (sw2960G) with etherchanel.
I connected the controller 2 distribution ports to the 2 ports of the switch (configured with etherchanel).
It worked like it should work.
But the problem is like this: if I take one cable that is connected to the switch and unplugged that cable from the switch (if that cable is the one connected to controllers port one) I have connectivity between both machines.
If I plug in the switch the cable connected to controller port one and take the other cable and unplugged that cable from the switch I stop the connectivity between the two machines.
I think that was not supposed to happenâ¦ because the LAG in the controller should put every AP in the second controller's port, and the connectivity between the machines should not end.
Can any one help me?
Can any one tell me what I am doing wrong?
Thanks in advance,
Rui

With LAG enabled in the controller I think I can have only one ap-manager interface.
The LAG will (it is supposed to) do the load balance automatically.
I mean, if one of the interfaces is âdownâ the other will have to coupe with all the AP's.
I should have always connection between the controller and the switch.
The STP of the controller is configured by default (STP Mode = OFF).
In the case of etherchannel load balanceâ¦ I saw the Cisco documentation and I did not saw any thing about that. I think that The LAG as to do that for the controllerâ¦ I'm right about that?
I will see the link that you advisedâ¦
Can you help me?
Thanks,
Rui

Motion control: PXI 7350 controller and UMI 7774 to interface with third-party driver UDK5114NW2

Dear community,
This is about Motion control in Labview: I try to control a step motor by using a PXI 7350 controller and UMI 7774 to interface with third-party driver UDK5114NW2. The problem is 5 Disable LEDS on UMI 7774 board always lit even when I check "enable" on "Motion I/O setting" in configuration of PXI 7350 motion controller. Furthermore, when I start to control step motor, it is not working and I found disable LED on UMI board still lit. I don't know how to solve this problem. Can someone help me to figure out? Thank you in advance!
Hau Nguyen.

Dear Community,
I said wrong, 4 disable LEDS on UMI 7774 Board instead of 5 as my previous post. Why nobody help me to solve this problem. I can not turn off disable LEDs on UMI 7774 Board so I can not start the strp motor. Please help me!
Hau Nguyen.

Do Anchor controller and foreign controller have to run on the same code version?

Hi All,
I have a 4402 anchor controller and 8 4402/4404 foreign controllers all running on code 4.2.61.0 for 1 year without any problem. All guest users are connected to the foreign controllers and then tunneled back to the anchor controller. Right now I need to replace a 25-AP license 4402 foreign controller with a 50-AP license 4402 controller. The new controller is running on code 7.0.116.0. I am wondering if the new controller can join the mobility anchor group so that guest users won't lose connectivity after the swap.
Please advise. Thank in advance.
Robert

Hi,
The below link will answer ur question!! (Inter Release controller Mobility )
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7_0_116_0.html#wp568458
Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra

Compaq Laptop make noise and can't open the windows.. Noise at HardDisk part

Why my sister's Compaq Laptop make noise and can't open the windows.. huhuhu.. the sound come from HardDisk in that laptop.. its sound like the HDD reader scratched the Disc insde.. how can it be?? my sister scold me already couze she wanna use for her work..

Hi Hawaiian_Starman,
Thank you for the suggestion.
I ran the first aid in the Keychain both for verification and for repair and both immediately returned with "no problems found".
As for the certificate, according the web administrator nothing had changed for the certificates.
even on the windows laptop I also get the certificate as being expired, but by simply accepting that I still have access.
I had a pop up every time that alerted me to the certificate issue, but whether I "continued" or not that still did not matter.
Yesterday, in an effort to find a solution, I went into the "details" and entered to trust this website.
Now that certificate issue does not pop up anymore. But I do not know how to reverse that either.
I have the feeling indeed it has something to do with a certificate, but how is the question.

Compaq/HP CCISS controller and Grub/Lilo

Similar Messages

Maybe you are looking for