Compaq Presario 420 windows 7 os installation problem

I accidently tried to disk sanitize my laptop and the proggress is incomplete. My computer has an error "BootMgr is missing. Press Ctrl + Alt + Del to restart" when I tried to start it. I tried to put Window 7 installation disk but Expanding window files is stuck in 0% and error appears. When I try to startup repair, there's an error about Boot Manager is missing. There is also no operating system listed after I click repair your computer. I also tried the diskpart method but its no use. I tried to use bootrec /scanos but its 0

@Seyren
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

Similar Messages

Compaq Presario SR5702UK - Windows 8?

Hi,
My Compaq Presario SR5702UK was running Window Vista, I then uninstalled Vista and installed Windows 8, I require the drivers for the Compaq Presario SR5702UK for Windows 8 but they don't seem to be on the website for download.
Does anyone know if it's possible to get them?
Thanks

Hi,
Please use following instructions to get missing hardware id's then post back:
http://www.wikihow.com/Find-Hardware-ID
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Windows 7 Installation problem: "no drives were found, click to load driver..."

I just purchased a Toshiba Satellite laptop (U945-S4140) that came with windows 8. I am trying to install windows 7 enterprise 64 bit.
I have the installation file on a bootable USB stick. In order to boot from the USB, I have to go into the BIOS settings and change from UEFI to CSM boot mode. Then the computer will boot from the usb stick and the windows 7 installation begins to work fine.
However, I soon get an error message that "no drives were found. click to load driver to provide a mass storage driver for installation."
I cannot figure out how to proceed. Any help would be greatly appreciated.
Cheers

I have tried many solutions....Maybe I should provide more details on my options.
Through my university I am granted the rights & license to use a copy on windows enterprise. From them I obtained a valid product key and also downloaded an ISO install file. It seems as if this file was designed to be burned to a dvd. I used windows 7 usb/dvd tool to burn the ISO file to a DVD. No problem there. However, my new laptop does not have an optical drive. So, I borrowed an external one that plugs in via USB. Again, in order to get ANYTHING to happen, I need to boot the USB(dvd rive) in CSM mode. Even then, it doesn't work. (I'm sorry but I forget the specific error I got here.....there have been so many methods and so many errors today)
Now, with this DVD, I have had a little bit of progress if I click the setup.exe file while Windows 8 is running. It begins the Windows 7 setup program, and even sees the harddrive! It asks me what partition I want to install to, and I selected the only 1 (of 4) that it said was 'available' to write to. Then, it loaded the installation files, but when it went to automatically restart, it froze during the 'starting windows' screen just as the little colored circles appear, that eventually form the windows logo. Again, I think the problem here might have been that during the restart, it looked to the USB-DVD drive, which needs CSM mode to boot properly, but Windows 8 can only start in UEFI mode.
Any attempt to put this ISO file onto a USB stick have not worked well. I used Rufus and the only thing that slightly worked was burning the ISO to the USB stick with a 'GPT partition scheme for UEFI controller' with the 'FAT32' file system. When using this to boot, I did not have to change the BIOS to CSM mode. The screen for 'loading files' came up like the installer was going to work. However, the computer then froze during the 'Starting Windows' screen, however, this time the little circles actually were able to form the windows logo. But, at that point I was left with a pulsing windows logo and it was stuck. It did not even make it to the actual installer.
The situation I posted about originally is slightly different. Some tech guys at my department's electronic shop have a bootable USB stick with the windows 7 enterprise installation software already on it. I used that and was at least able to get a little bit into the windows 7 setup before it told me it cannot find a disk to install to (as in my original post).

Compaq Presario CQ40-340 TU battery problem

Hello ,
I had a battery problem it says, consider replacing your battery. And it sucks, it already ended the warranty.
it was i think 1 year and 1 month when my battery had this problem. It charge a little bit after 30 sec to 1 min my laptop turns off. Its unusual i think my battery only last a year. is there latest battery recall on Compaq Presario batteries?
my CT: is 6AQEAC ***********
THANKS
Regards,
bk

See this
http://bpr.hpordercenter.com/hbpr/

Compaq Presario Component Services App. Problem 4 0 clovis 0 12-28-2010 09:52 AM

Am beginning to wonder if my posting has been pushed aside. NONE of the REPLIES relate to the problem that I explained in the body of my posting. Please assist me in clearing up my original concern.
Thanks,
Mato Paha
Mato Paha

http://h30434.www3.hp.com/t5/Desktop-Operating-systems-and/Compaq-Presario-Component-Services-App-Pr...
Thank you for visiting the HP Support Forum. This is a peer to peer community for customers to connect and share solutions on their HP consumer products. If you have direct feedback for HP about their products or services, please use the link below.
http://welcome.hp.com/country/us/en/wwcontact_us.html
If you have other questions and concerns, please feel free to send me a private message
Wendy M - HP Support Forums Moderator
Click the Kudos star as a way to say "thank you" for helpful posts.
Be sure to come back and click the 'Accept as Solution' button on the post that solved your issue - it may help someone else.
Rules of Participation

Compaq Presario CQ41-208TU Notebook Audio Problem - Fariya Enterprises

Hello my hp Compaq Presario CQ41-208TU Notebook drivers crashes i have to update the drivers suggest the permanent fix
Thanks
Fariya Enterprises

Hi,
I'm not sure that I understand your problem well.
If you are looking for latest drivers to this specific model then you may download them from here.
** Say thanks by clicking the "Thumb up" icon which is on the left. **
** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

After Windows re-installation = problems

After i reinstall windows i have these problems:
Any ideas? Waisting of time, cant work..

I would do a clean uninstall and then re-install: Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6

Compaq presario C700 CD/DVD drive problem

Hi all my product no is "compaq presario c700". While starting my laptop the CD/DVD drive makes dragging sound (two times). It doesn't read any disk drives. So my question is, is there any solution to solve this problem? Until i need to replace my drive? Please help me

Hi,
Please try this solution first:
http://support.microsoft.com/mats/cd_dvd_drive_problems/en-us
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Windows 7 Installation problem: "no drives were found, click to load driver to provide a mass storage driver..."

I just purchased a Toshiba Satellite laptop (U945-S4140) that came with windows 8. I am trying to install windows 7 enterprise 64 bit.
I have the installation file on a bootable USB stick. In order to boot from the USB, I have to go into the BIOS settings and change from UEFI to CSM boot mode. Then the computer will boot from the usb stick and the windows 7 installation begins to work fine.
However, I soon get an error message that "no drives were found. click to load driver to provide a mass storage driver for installation."
I cannot figure out how to proceed. Any help would be greatly appreciated.
Cheers

Hello Maxxpower33, thank you for your words.
I looked through the error logs that could be generated from the tool and found this one which may be what you experienced. Kindly let me know if this is what you got:
"Files copied successfully. However, we were unable to run bootsect to make the USB device bootable. If you need assistance with bootsect, please click the "Online Help" link above for more information."
Some further information is that I found this post where another user experienced the same error on a laptop, although the speculation mentioned in the post is that the user does not have a Windows store account under which he purchased the license for Windows
7 Home Premium, which is the flavor he was trying to get on the bootable drive. However, this does not seem to be a valid response due to the fact that the tool does not check Windows XAuthCert Servers for validation on licensing. So ignore that
portion of the post, but the 2nd post helps a bit by linking to another article, providing both below.
Forum Port With Same Error
Article with 4 methods to create
a bootable Windows 7 USB Drive
In that first post, further down, is another reply to a tool that I have not tested with. So please use caution on this one as I cannot find very much feedback other than on their own website, but sounds much like the first tool I mentioned in my first
post "Unetbootin", but this one is called Rufus, and two people did mention they had good success with this tool after having difficulties with the Windows utility.
Rufus
After all that is said and done, there is not 1 tool that will work for everyone all of the time on every environment. Why? I would like to know also...but speculate hardware/firmware/bios combinations could be the culprit. One of these
tools should work for you and it would be my recommendation to try them in this order (skipping what you've already tried):
1) Windows 7 USB/DVD Download Tool
2) Unetbootin
3) Manually creating the partition and xcopy'ing the extracted ISO to it
4) Rufus
5) Borrow a PC with a DVD-R in it and burn the ISO to a disc and install from it. If your laptop does not have a DVD drive, an external drive can be purchased for roughly $25 or less. Or if you have an internal drive laying around, buy an enclosure
for about $15 and put the drive inside there and attach it to your laptop via USB or eSATA.
As always, my advice is nothing more than my opinion, which are like bungholes...everyone has one and they all stink! LOL!
John Fester

Windows 8 installation problem using bootcamp!

Hi guys, I would really appreciate some help with this, I think I might of made a big mistake.
Ok so I bought windows 8 yesterday to run on my iMac through bootcamp.
I went through the instllation process and came to downloading the drivers (windows support software) but here is where I think i went wrong, when i was asked to burn the windows support software to a cd or save it on to an external drive I chose the option of saving onto a drive but I actually just ended up saving the software on to the main hard drive for my iMac.
I continued to install windows 8 but after installation as expected I'm having problems with the keyboard, mouse, Internet etc without any support software. I went to 'my computer' and the local hard drive only shows the part of drive of the that was particitianed for windows and can't seem to find any way of accessing the mac os x side of the hard drive. I cant even transfer to the mac os x from windows to figure out the problem from there.
Could any one please help with this?
Thanks

Welcome to the Apple Support Communities
After using Boot Camp, your computer will start always in Windows. To start in OS X, just hold the X key while your Mac is starting. If you want to start always in OS X, after starting in OS X, go to System Preferences > Startup Disk, and select the OS X partition.
By default, Windows can't read the filesystem that OS X uses for the partition, so that's why you can't access to the OS X partition. Also, you should have burnt the drivers onto a DVD or a USB drive.
As you have already downloaded the drivers, after starting in OS X, copy them to a USB drive or burn them into a DVD. Then, start in Windows and install them. Note that Windows 8 requires Boot Camp 5 drivers, that you can only get from Boot Camp Assistant if you are running OS X 10.8.3. If you want to be sure that you install the correct drivers, I recommend you to download again the Boot Camp 5 drivers from the Apple webpage > http://support.apple.com/kb/DL1638

Windows XP Installation problem on Mac Pro (Early 2009)

I am wanting to install Windows XP on 400GB of my hard drive in Bay 2
I have 2 hard drives in my Mac Pro. The 1st one came pre-installed and I got a 1TB Western Digital SATA and formatted it as Mac OS Journaled. I used The Bootcamp Utility to make a Windows partition on my 2nd hard drive.
Once I do that I insert the Windows XP SP3 install disc to install it and it says it cannot install it because some random file is missing that is a random bunch of letter and numbers and it says I should erase the partition and try formatting it again. While I'm still using the Windows XP install disc I try doing this it does not work and then when I boot back into Snow Leopard the Bootcamp partition is still there.
Is this not possible? Or is the only way to install Windows XP on the hard drive in bay 2 by formatting the entire drive for Windows?

Since the Vista recovery works fine there must be a problem with the XP installation CD created by nLite. And yes this installation CD was not good. I created it with all current Security Patches and with all available Toshiba Satellite A200 Windows XP drivers. Obvisiously i picked up a wrong driver. May a 64-bit one.
I tried this:
First I created a new Windows XP disc only with the Toshiba Storage Manager driver. This XP Installation works.
Then I created again a Windows XP disc will all Security Patches and all Toshiba Drivers. I doubble checked that I did NOT picked up a 64-bit driver. And this disc works. Thanks all.

Rs480 windows-sata installation problem

Hi all,
Whenever I try to install windows in my system I press the F6 button and loads the sil3112 sata driver. The first time I tried this worked(win xp with no sps) and I got to install windows. But after sometime I decided reinstall windows. This time when I tried to install windows(win xp with sp1) with the usual procedure like loading the sata driver through F6 method it didnt work. When I reach the partitioning blue screen and when I give prompt to format the drive or partition it windows say that “however the disk does not contain a windows compatible partition” and thus have to exit.
The same thing happened when I tried to install xp 64bit with sil drivers given in msi site.
Please do help me with this problem.
My mobo specs are given below.
<<< System Summary >>>
< Processor >
Model: AMD Athlon(tm) 64 Processor 3000+
Speed: 1.79GHz
Model Number: 3000 (estimated)
Performance Rating: PR2687 (estimated)
Type: Standard
L2 On-board Cache: 512kB ECC Synchronous, Write-Back, 16-way set,
64 byte line size
< Mainboard >
Bus(es): ISA X-Bus PCI USB FireWire/1394
MP Support: 1 CPU(s)
MP APIC: No
System BIOS: Phoenix Technologies, LTD 6.00 PG
Mainboard: MS-7093
Total Memory: 447MB DDR-SDRAM
< Chipset 1 >
Model: Micro-Star International Co Ltd (MSI) ???
(5950)
Front Side Bus Speed: 1x 199MHz (199MHz data rate)
< Chipset 2 >
Model: Advanced Micro Devices (AMD) Athlon 64 /
Opteron HyperTransport Technology
Configuration
Front Side Bus Speed: 2x 995MHz (1990MHz data rate)
Total Memory: 512MB DDR-SDRAM
Memory Bus Speed: 2x 199MHz (398MHz data rate)
< Video System >
Monitor/Panel: Samsung Samtron 40Bn
Adapter: ATI RADEON Xpress 200 Series
< Physical Storage Devices >
Removable Drive: Floppy disk drive
Hard Disk: ST320413A (19GB)
Hard Disk: ST380817 AS SCSI Disk Device (75GB)
CD-ROM/DVD: SONY DVD-ROM DDU1622 (CD 40X Rd) (DVD 5X Rd)
< Peripherals >
Serial/Parallel Port(s): 1 COM / 1 LPT
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
FireWire/1394 Controller/Hub: VIA OHCI Compliant IEEE 1394 Host Controller
Keyboard: Standard 101/102-Key or Microsoft Natural PS/
2 Keyboard
Mouse: PS/2 Compatible Mouse
< MultiMedia Device(s) >
Device: Realtek AC'97 Audio
< Network Services >
Adapter: Realtek RTL8139/810x Family Fast Ethernet NIC
<<< Mainboard Information >>>
< Mainboard >
Manufacturer: Micro-Star
MP Support: 1 CPU(s)
MPS Version: 1.40
Model: MS-7093
System BIOS: 05/13/2005-RS480-SB400-6A666M4DC-00
< System Memory Controller >
Location: Mainboard
Error Correction Capability: None
Number of Memory Slots: 4
Maximum Installable Memory: 2GB
Bank0/1 - A0: None None None None DIMM 512MB/64
Bank2/3 - A1: Empty
Bank4/5 - A2: Empty
Bank6/7 - A3: Empty
< Chipset 1 >
Model: Micro-Star International Co Ltd (MSI) ???
(5950)
Bus(es): ISA X-Bus PCI USB FireWire/1394
Front Side Bus Speed: 1x 199MHz (199MHz data rate)
In/Out Width: 16-bit / 16-bit
< Logical/Chipset 1 Memory Banks >
Power Save Mode: No
Fixed Hole Present: No
< Chipset 2 >
Model: Advanced Micro Devices (AMD) Athlon 64 /
Opteron HyperTransport Technology
Configuration
Bus(es): ISA X-Bus PCI USB FireWire/1394
Version: 1.02
Front Side Bus Speed: 2x 995MHz (1990MHz data rate)
Maximum FSB Speed / Max Memory:2x 1000MHz / 2x 200MHz
In/Out Width: 16-bit / 16-bit
IO Queue Depth: 4 request(s)
< Chipset 2 Hub Interface >
Type: HyperTransport
Version: 1.02
In/Out Width: 16-bit / 16-bit
Speed: 2x 995MHz (1990MHz data rate)
< Logical/Chipset 2 Memory Banks >
Bank 0: 512MB DDR-SDRAM 3.0-3-3-3CL 2CMD
Channels: 1
Speed: 2x 199MHz (398MHz data rate)
Multiplier: 1/9x
Width: 64-bit
Refresh Rate: 5.00µs
Power Save Mode: No
Fixed Hole Present: No
Notice 224: SMBIOS/DMI information may be inaccurate.
Tip 2511: Some memory slots are free so the memory can
be easily upgraded.
Warning 100: Large memory sizes should be made of
Registered/Buffered memory.
<<< CPU & BIOS Information >>>
<< Processor 1 >>
< Processor >
Model: AMD Athlon(tm) 64 Processor 3000+
Speed: 1.79GHz
Model Number: 3000 (estimated)
Performance Rating: PR2687 (estimated)
Type: Standard
Package: FC µPGA939
Multiplier: 9/1x
Minimum/Maximum Multiplier: 9/1x / 9/1x
Generation: G8
Name: M1F Athlon 64 (K8 ClawHammer) 90nm ?GHz+ ?V
Revision/Stepping: 1F / 0 (108)
Stepping Mask: DH8-D0
Microcode: MU0FF041
Core Voltage Rating: 1.400V
Min/Max Core Voltage: 1.400V / 1.450V
Maximum Physical / Virtual Add:40-bit / 48-bit
Native Page Size: 4kB
< Co-Processor (FPU) >
Type: Built-in
Revision/Stepping: 1F / 0 (108)
< Processor Cache(s) >
Internal Data Cache: 64kB Synchronous, Write-Back, 2-way set, 64
byte line size
Internal Instruction Cache: 64kB Synchronous, Write-Back, 2-way set, 64
byte line size
L2 On-board Cache: 512kB ECC Synchronous, Write-Back, 16-way set,
64 byte line size
L2 Cache Multiplier: 1/1x (1791MHz)
< Upgradeability >
Socket/Slot: Socket 939
Upgrade Interface: Unknown
Supported Speed(s): 3.00GHz+
< Processor Power Management >
Processor Throttling Enabled: Yes
Throttle Range: 34% - 100%
<<< PCI(e), AGP, CardBus Bus(es) Information >>>
<< Generic >>
<< Interface >>
< System Buses >
PCI 64-bit Bus(es): 1
PCI 66MHz Bus(es): 1
PCI Bus(es): 3
Interface Version: 2.20
< Interface Properties >
Config space access mechanism :Yes
Config space access mechanism :No
Cycle generation mechanism 1 s:No
Cycle generation mechanism 2 s:No
<<< Video System Information >>>
<< Video Adapter >>
<< Primary Display Driver (display) >>
< Video Adapter >
Model: ATI RADEON Xpress 200 Series
Chipset: ATI RADEON Xpress 200G Series (0x5954)
RAMDAC: Internal DAC(400MHz)
Video BIOS: BK-ATI VER008.020I.030.000
VGA Compatible: No
Total Memory: 64MB (64MB Video) (118MB System)
Texture Memory: 182MB
Supports DIME Texturing: Yes
< Video BIOS >
Date: 04/12/20
< Current Video Mode >
Mode: 1024x768 16M+ TrueColour (32-bit)
Current Refresh Rate: 60Hz
Virtual Desktop Size: 1024x768
< Video Driver >
Model: ati2mtag.sys
Version: 6.14.10.6490
Expected Windows Version: 4.00
Video Acceleration: Yes
Screen Saver Active: 60 minutes(s)
Screen Saver Name: C:\WINDOWS\System32\logon.scr
Low Power Saving Active: No
Power Off Saving Active: No
<<< Sound Card Information >>>
<< Wave Input Devices (Recording) >>
<< Realtek AC97 Audio >>
< General Information >
Device Name: Realtek AC97 Audio
Manufacturer: Microsoft
Version: 5.10
Product ID: 101 / 1
With regards and concern,
Cherian

Quote from: Ui30 on 04-July-05, 19:41:11
Why not install like you did before, not using a slipstreamed version? It may do the trick!
Are you runnign single SATA? (I didn't find it in your summary, may looked over it ... maybe you can give your specs like in my signature )
i'll try you way.but its difficult to get a pure xp. i'll have to dig hard for that.
for ur 2nd question. i am not running a single sata. i have one sata 80gb and another 20 gb ide.is that a problem

Windows XP installation problems in SATA HDD

I am trying to install XP Pro from the CD on a new pc, as listed on the sig.
The computer at first started realtek boot agent, but didnt found any HDD, i found this forum and made some changes:
Pre-Raid Bios Tweaks
Standard Cmos Features
The only thing I change here is to enable "32bit transfer mode" whenever I connect new devices to the Intel IDE controller.
Note: Devices attached to the Promise controller and the Intel Raid(when it is enabled) will NOT appear in the standard Cmos page
Advanced Bios Features
Everything on defaults is usually fine except I always change the following for WinXP:
APIC ACPI SCI IRQ - Enabled
Boot Device select is also on this page and you'll be changing it after all the hardware is setup; more later.
Advanced Cipset Features
Confirm that the memory timing "by SPD" is enabled
PNP/PCI Configurations
Clear NVRam option I always set to "YES" before the first boot after making hardware changes. I'm not sure how important this is but I understand that's what you're supposed to do. I believe it forces the motherboard to detect hardware changes. It reverts to "NO" after the reboot.
PCI/IDE Busmaster set to "enabled" to speed things up outside of Windows.
Integrated Peripherals (Before Raid for most flexibilty)
Onboard Promise IDE - Disabled if you have nothing attached to IDE3 and Serial 3&4
ON-Chip IDE Configuration:
Native Mode (Supported by WinXP- Allows all devices connected to IDE 1&2 and Serial 1&2 to be detected)
SATA Only or PATA Only (select the one that you boot XP with)
Keep SATA Active - Yes (if option available)
Keep PATA Active - Yes (if option available)
PATA Channel selection - Both (if option available)
Configure SATA as Raid - No (if option available)
Leave other settings here at default
Note: Some older Bios versions may appear different than above
Frequency/Voltage Control
Dynamic Overclocking - Disabled
Performance Mode - Slow
Dram Frequency - Auto
Adjust CPU Bus - 201 (for "c" type cpu's)
DDR Voltage - 2.65 (minimum for Dual-Channel Mem stability)
AGP Voltage - 1.55
This is a thumbnail at 63% scale, click for full sized image.
Note: some features above may not appear with your Bios
Note: performance & overclocking features can be increased again AFTER the Raid array has been setup and is stable with Windows.
The above text was copy pasted from this forum.
With my hdd allready recognized i started windows xp configuration, kept on going, formatted using NTFS, win config the started copying files for installation, then
gets to a point that says 'This portion of setup has completed successfully, remove
any disks from the A:\ drive, computer will reboot in 15 seconds.'
so it reboots, and it goes through the cycle again.
It reads the CD, asks if I want to setup Windows XP, then this msg appears "there
is already a \windows directory on the C:\ drive, do you want to do a dual
boot, do you want to delete the contents of this folder and install windows there,
or do you want to install to a separate directory", and a link to the microsoft website for advice on dual booting.
It does this over and over and over again.I tried ejecting the XP CD ROM and restarting, but then it
starts up and says "Missng Operating System"
why the heck does XP insist on restarting, only to go through the exact same setup
steps again? What did i do wrong
Thanks in advance
Many thanks.
Really

Thx for the advice, unfortunatly it didnt work, following your advice i didnt touch any key, the following msg appeared"invalid system disk", but before that i had one error(ive been having this error everytime i tried to install this windows xp cd on this new mobo): i made full format(10-20m), the pc started copying files but it stopped at 2% in the gdi32.dll file, saying to check if i had my cd on the drive, retried it 10 times then i ignored it, the next file in line made the same error, i kept ignoring all files(98% left and with same problem) till 100% completion. Meanwhile, and after going by the full format again, got the same error on the gdi32.dll file, this time i retried it a couple times and quited config(F3),rebboted and made the process all over again, this time i didnt formatted, the config made a disk maintainance, forced me to reboot. Booting from cd for the third time, i kept existing format but this time config copied all windows config files till the end, rebooted, touched no keys, got the same feared msg again"Invalid system disk".
Only ideas i have are: bad cd rom drive? bad cd?
All advices are certainly welcome.

Windows 7 Installation Problem on T61

Hello everyone!
Yesterday, I tried to install Windows 7 Beta (x86) on my T61 as dual-booting with Windows Vista Business (x86) OEM with SP1, but when the installation stage complete and my computer was restarted automatically, I got the message "Windows Setup Could not configure Windows to run on this computer's hardware". I tried to load all T61's drivers during installation phase, but Windows setup shown that message again! How do I resolve this problem?
Thanks very much ... and Happy New Year!

I tried it also on my T61p --> worked.
The only problem I have: my harddrive gets only a acore of 2.9 --> so there is a issue with the SATA (?) driver or something,...

Windows 7 installation problem

Hi, I'm trying to install Windows 7 (specifically, it's windows 7 professional with service pack 1, 64-bit) on my mac (a 13-inch mid-2012 MacBook Pro running OSX 10.8.3) via Boot Camp, and I've run into a problem.
I had no issues when going through the BootCamp Assistant, have a USB drive with all the needed files and everything, and have partitioned my hard drive. The problem comes up when I get to the point of resetting my computer.
I get a black screen with the message "no bootable device - insert boot disc and press any key," even though the USB drive is sitting right in the slot and is being read by the computer. Pressing keys does nothing, naturally.
The issue isn't getting back to OSX like some other posts I've seen on similar topics, I can do that just fine by holding down the "alt" key on startup (incidentally, the USB drive shows up just fine in my list of available startup disks, so I know it's being read). I want to know how to find a workaround for this problem and continue with the installation.
Any help would be much appreciated, thanks!

Hello jaredm42
Sometimes it could be that other devices are plugged in when trying to install Windows Check to make sure nothing else is plugged in that could take power away from the USB drive and start the process again.
Boot Camp: Windows installation boots to black screen with blinking cursor
http://support.apple.com/kb/TS4536
Regards,
-Norm G.

Compaq Presario 420 windows 7 os installation problem

Similar Messages

Maybe you are looking for