Compaq proliant ML370 installation
we are triyng to install solaris 8 intel on compaq proliant ml370. when we are loading the firt software cd at the point when is loading the package SUNWnamow the system hang without any warning messages.
we cannot complete the installation.
we will apreciate all yours helps regarding this matter.
B4N
Check out the HP Compaq web site and you shuld be able to find the Solaris drivers that are needed. http://h18023.www1.hp.com/support/files/server/us/download/19340.html
Similar Messages
-
No /dev/lp? on COMPAQ Proliant ML370 with Solaris 8 x86 10/00
Dear Sir,
I have a problem about the /dev/lp? port in Solaris 8 x86 with COMPAQ Proliant ML370. I have seen in the boot interpreter it has detected a parallel port
device isa/lp@1...., but after I boot -r to start Solaris 8
OS it don't make any /dev/lp? or /devices/isa/lp*... and if
I mknod /dev/lp? myself it cannot print out ( I use cat /etc/hosts >> /dev/lp1, /dev/lp1 major=83 minor=1 ) It say "cannot create". I wonder why this happens, If I install this Solaris 8 x86 on other PC model. It has /dev/lp1 and can print out successfully. I try many ways such as: upgrade latest ROMPAQ BIOS firmware,
install lp driver patch set, install acpi patch. But still don't work. I found that serial ports (asy) which are ACPI is working because I can redirect console to serial port (asy).
Do anyone have the idea to solve or track down this problems. Thanks a lot...Check out the HP Compaq web site and you shuld be able to find the Solaris drivers that are needed. http://h18023.www1.hp.com/support/files/server/us/download/19340.html
-
Kernel panic on Compaq Proliant ML370 G2
Happens during installation of Solaris 8 (02/2002):
SunOS Release 5.8 Version Generic_108529-13 32-bit
Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
panic[cpu0]/thread=fec17660: BAD TRAP: type=0 (Divide Error Exception) rp=fec12b70 addr=0
Divide Error Exception
pid=0, pc=0xfea6b5ef, sp=0x1c, eflags=0x10246
eip(fea6b5ef), eflags(10246), ebp(fec12bc0), uesp(1c), esp(fec12ba0)
eax(d18a09), ebx(d18a09), ecx(0), edx(0), esi(0), edi(1c)
cr0(80050033), cr2(0), cr3(1e69000)
cs(158) ds(160) ss(5868) es(160) fs(1a8) gs(1b0)
fec12aa4 unix:die+9c (0, fec12b70, 0, 0, 1c)
fec12b5c unix:trap+2f6 ()
fec12b70 unix:_cmntrap+94 (fec10160, e1420160, 1c)
fec12bc0 unix: pcplusmp:apic_clkinit+77 ()
fec12bdc unix:mach_clkinit+113 (fec09750)
fec12c1c unix:cbe_init+6b ()
fec12c2c genunix:main+1e ()
skipping system dump - no dump device configured
rebooting...Check out the HP Compaq web site and you shuld be able to find the Solaris drivers that are needed. http://h18023.www1.hp.com/support/files/server/us/download/19340.html
-
Install Solaris10 on HP ProLiant ML370 G6, "No Disk" error
Hello,
I want to install Solaris10 on HP ProLiant ML370 G6 servers which are on the Hardware Compatible List( HCL). However, I always encounter "No disk" issue and installation fails. The disks are HP SAS disks.
I searched online and knew that CPQAry3 driver must to be installed first. I did but the "No disk" error still happens later.
I am wondering what else I should do?
TomHi Tom,
You have to apply the ROMPaq Firmware Upgrade before.
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=emea_africa&prodNameId=3884311&prodTypeId=15351&prodSeriesId=3884310&swLang=13&taskId=135&swEnvOID=2023
Marco -
Solaris 8 on Compaq ProLiant 1600
We tried to install Solaris 8 on a Compaq ProLiant 1600/500
with dual processor. The installation failed in the "scanning hardware
configuration" phase entering into debugger mode.
We know that our configuration is NOT on the hardware compatibility list.
On the other hand the Compaq ProLiant 1600 (2 CPUs, PIII-550) can be found
in the HCL.
Any kind of help would be higly appreciated.
AndrasThe first thing to do with a Compaq is make sure the latest and greatest rompaq has been applied to the board and all devices. Next, download and use the latest and greatest Solaris DCA diskette and use it for the install boot. I am making the assumption you are using the CD this time around. If that doesnt work, you will have to remove all but the bare minimun of hardware and try the install then add each device one by one. The DCA diskettes are updated regularly so thelatest one may solve the issue.
Lee -
Installing Solaris 10 on Compaq Proliant 1600 with Smart 2DH PCI controller
I'm trying to put Solaris 10 on a fairly old 350 Mhz Compaq Proliant.
Compaq SMART-2DH Array controller Ver C rev 3.08
This is a PCI card
I have tried downloading HP's drivers for the Smart II controller and renaming the DU/ folders to 210 instead of 28, and the installation program will process the drivers
When it continues on to the part where you select the type of installation, it gives these errors:
/platform/i86pc/kernel/drv/smartii: undefined symbol 'eisa_nvm'
WARNING: mod_load: cannot load module 'msartii'
WARNING: forceload of drv/smartii failed
WARNING: forceload of drv/smartii failed
Then it will continue on to the GUI portion of the install and give the error about not having any available disks to install on to (check cables)
Is there any way to make Solaris 10 load these drivers? I know it doesn't support EISA, but this card is PCI. Not sure why it tries to load EISA drivers for it.
This thing also has SCSI built into the motherboard, does anyone know if Solaris 10 will support that particular controller? No idea what it's called. If it will, I'm just going to plug the hard disk cable in to that and go with it.Has any body found a way to get Solaris 10 to install with the Smart-2DH controller? I've got a Compaq Proliant 1850R that also has that raid controller and the Solaris 10 install rejected the Solaris 8 driver.
-
Compaq Proliant 1600 Server Install
Hi!
I'm working on setting up a Compaq Proliant 1600 server. . .I've made a bit of progress thanks to a few posts on the forum.
I've bugged everyone on the irc channel so now its time to ask here :oops:
Basically, I can't get the Arch install to recognize the scsi drives (2) I've got...
What I've done:
1. Loaded all the modules (cpqarray etc...)
2. In '/dev' I did 'mkdir ida'
3. Next I 'mknod /dev/ida/c0d0p1 b 72 1' <---this should be my swap
4. Then I 'mknod /dev/ida/c0d0p2 b 72 2' <-----this is my /
Now I'm not sure what to do...
Since I've been able to partition the drives the next step seems to be to
set filesystem mountpoints, right? The Arch install doesn't recognize the drives at all - It simply says "NONE".
So, if anyone has any tips or advice I'd appreciate it
I'm setting this server up for my school's website - and thought I'd go with Arch. . .
Thanks!
nedsonIt's all about loading the right modules. With < 0.7 ISO's you can modprobe cpqarray. Later ISO's don't have cpqarray anymore, they use cciss.
Some threads you'll want to read:
Help no cpqarray modules
Compaq proliant install help -
Latest kernel crash while installing on a Compaq Proliant ML370G2
SunOS Release 5.8 Version Generic_108529-13 32-bit
Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
panic[cpu0]/thread=fec17660: BAD TRAP: type=0 (Divide Error Exception) rp=fec12b70 addr=0
Divide Error Exception
pid=0, pc=0xfea6b5ef, sp=0x1c, eflags=0x10246
eip(fea6b5ef), eflags(10246), ebp(fec12bc0), uesp(1c), esp(fec12ba0)
eax(d18a09), ebx(d18a09), ecx(0), edx(0), esi(0), edi(1c)
cr0(80050033), cr2(0), cr3(1e69000)
cs(158) ds(160) ss(5868) es(160) fs(1a8) gs(1b0)
fec12aa4 unix:die+9c (0, fec12b70, 0, 0, 1c)
fec12b5c unix:trap+2f6 ()
fec12b70 unix:_cmntrap+94 (fec10160, e1420160, 1c)
fec12bc0 unix: pcplusmp:apic_clkinit+77 ()
fec12bdc unix:mach_clkinit+113 (fec09750)
fec12c1c unix:cbe_init+6b ()
fec12c2c genunix:main+1e ()
skipping system dump - no dump device configured
rebooting...Has any body found a way to get Solaris 10 to install with the Smart-2DH controller? I've got a Compaq Proliant 1850R that also has that raid controller and the Solaris 10 install rejected the Solaris 8 driver.
-
2nd CPU not recognized on Compaq Proliant 1500
I have x86/2.6 running on a dual CPU Compaq Proliant 1500, but it's not recognizing the 2nd CPU. (verified with mpstat)
Does anyone know how to convince x86 to initialize the 2nd CPU?
Thanks in advance!
DavidSaw your post at http://forum.sun.com/profile.jsp?user=10948. I was having the exact same problem with the EXACT same hardware and I got the solution for you too. No charge! :-)
I contacted Compaq support and got a REAL sharpy on the phone. Compaq EISA config has an undocumented feature called 'Advanced'. To turn on the second CPU in Compaq ROM, follow these steps.
Start EISA config.
To use the 'Advanced' feature, merely hit 'CTRL-A' at the EISA config main menu.
Run configure system.
When it is done, go into Edit Details and scroll down until you see a line item called APIC.
It probably says DISABLED.
Highlight it and hit the ENTER key.
At that point, you'll see two options for 'ENABLE'.
Pick the one that says 'Full Table'. 'Full Table - Mapped' evidently don't mix with Solaris.
Save and exit, cycle power, and restart EISA config.
Save, exite, recycle power again.
At this next power up, the post message should say 'Processors Running at xxx' The next line should say Processor 2 initializing. When Solaris boots up, use the psrinfo command (no options) and it should show both processors up and running. psadm allows you to change the state of the other processor.
Let me know how this works. Mine is working like a champ! -
Installing Arch i686 on my Compaq ProLiant 5500. Will it detect the..
I got a Compaq ProLiant 5500 and going to install Arch on it for a web/email server so will it detect the SCSI's out of box or what?
Also, how should I partition my drives for it? It'll be a web/mail/dns/dhcp server.The driver for SCSI drives is in the ARch kernel so it shouldn't be a problem. I have a scsi-drive on one of my computer's and it has no problems. As how to partition, I'd look at one of the BSD-guides. Alot of BSD's are used for mail servers and have good advice on how to partition. If i remember correctly you'll want partitions for /, /tmp, and /var... Here, I done looked it up for ya :
http://openbsd.org/faq/faq4.html#Partitioning -
9IAS install on Compaq Proliant DL360
I have been trying to install 9IAS Release 2 (9.0.2.0.1) - on Compaq Proliant DL360 (Win200).After install EM website stops intermittently and unable to run Forms - is there a
problem with 9IAS and Proliant DL360 and is there any way round it?Alec,
Some ideas:
1) Do you have .Net running simultaneously?
See: http://download-west.oracle.com/docs/cd/B10573_02/relnotes.902/addendum/oem.htm#1007067
2) Do you have a fixed IP address or DHCP?
See: http://download-west.oracle.com/docs/cd/B10573_02/relnotes.902/addendum/ipchange.htm#1004903
3) Did you install the infra & the middle tier in separate ORACLE_HOMEs?
Thanks,
Ashesh Parekh
Oracle9iAS Product Manager -
Can someone please give me some tips as i need to install Arch on my Compaq Proliant server.
I know i need the cpqarray , tlan , sym53c8xx_2 , sd_mod , scsi_mod
But i still cant see the dev files for ida blah blah so Arch cant see my drive.
I have the raid setup as mirroring ( Raid 1 ) on 3 * 9Gb scsi drives.
If you have installed Arch on one of these servers can you help me out. I will be using the 0.7.1 noodle cd.
Regards,
Justin Smithies/etc/udev/udev.conf
# udev.conf
# Where in the filesystem to place the device nodes
udev_root="/dev"
# The name and location of the udev database.
udev_db="/dev/.udevdb"
# The name and location of the udev rules file(s).
udev_rules="/etc/udev/rules.d"
# The syslog(3) priority: "err", "info", or the numerical value.
udev_log="err"
/etc/udev/scsi-devfs.sh
#! /bin/sh
# scsi-devfs.sh: udev external PROGRAM script
# Copyright 2004 Richard Gooch <[email protected]>
# Copyright 2004 Fujitsu Ltd.
# Distributed under the GNU Copyleft version 2.0.
# return devfs-names for scsi-devices
# Usage in udev.rules:
# BUS="scsi", KERNEL="sd*", PROGRAM="/etc/udev/scripts/scsi-devfs.sh sd %b %n",
NAME="%c{1}", SYMLINK="%c{2} %k %c{3} %c{4}"
# BUS="scsi", KERNEL="sr*", PROGRAM="/etc/udev/scripts/scsi-devfs.sh sr %b %n",
NAME="%c{1}", SYMLINK="%c{2} %k %c{3} %c{4}"
# BUS="scsi", KERNEL="st*", PROGRAM="/etc/udev/scripts/scsi-devfs.sh st %b %n",
NAME="%c{1}", SYMLINK="%c{2} %k %c{3} %c{4}"
# BUS="scsi", KERNEL="sg*", PROGRAM="/etc/udev/scripts/scsi-devfs.sh sg %b %n",
NAME="%c{1}", SYMLINK="%c{2} %k %c{3} %c{4}"
# Find out where sysfs is mounted. Exit if not available
sysfs=`grep -F sysfs /proc/mounts | awk '{print $2}'`
if [ "$sysfs" = "" ]; then
echo "sysfs is required"
exit 1
fi
cd $sysfs/bus/scsi/devices
case "$1" in
sd)
# Extract partition component
if [ "$3" = "" ]; then
lpart="disc"
spart=""
else
lpart="part$3"
spart="p$3"
fi
sr)
lpart="cdrom"
spart=""
st)
# Not supported yet
exit 1
sg)
lpart="generic"
spart=""
exit 1
esac
# Extract SCSI logical address components
scsi_host=`echo $2 | cut -f 1 -d:`
scsi_bus=`echo $2 | cut -f 2 -d:`
scsi_target=`echo $2 | cut -f 3 -d:`
scsi_lun=`echo $2 | cut -f 4 -d:`
# Generate long and short common name parts
l_com="bus$scsi_bus/target$scsi_target/lun$scsi_lun/$lpart"
s_com="b${scsi_bus}t${scsi_target}u${scsi_lun}$spart"
# Generate long and short logical names
l_log="scsi/host$scsi_host/$l_com"
s_log="$1/c${scsi_host}${s_com}"
readlink $2 | grep -F -q pci
if [ "$?" != "0" ]; then
# Not a PCI controller, show logical locations only
echo $l_log $s_log
exit 0
fi
# Extract PCI address
tmp=`readlink $2 | sed -e 's@/host.*/.*@@'`
pci_addr=`basename "$tmp"`
pci_domain=`echo $pci_addr | cut -f 1 -d:`
pci_bus=`echo $pci_addr | cut -f 2 -d:`
pci_slot=`echo $pci_addr | tr . : | cut -f 3 -d:`
pci_function=`echo $pci_addr | cut -f 2 -d.`
# Generate long and short physical names
l_pci="domain$pci_domain/bus$pci_bus/slot$pci_slot/function$pci_function"
l_phy="bus/pci/$l_pci/scsi/$l_com"
s_phy="$1/pci/$pci_addr/$s_com"
echo $l_phy $s_phy $l_log $s_log
/etc/udev/rules.d/udev.rules
# This ruleset should provide a DevFS-compatible device tree.
# There are a number of modifiers that are allowed to be used in some
# of the different fields. They provide the following subsitutions:
# %n the "kernel number" of the device.
# For example, 'sda3' has a "kernel number" of '3'
# %e the smallest number for that name which does not matches an existing node
# %k the kernel name for the device.
# %M the kernel major number for the device
# %m the kernel minor number for the device
# %b the bus id for the device
# %c the string returned by the PROGRAM
# %s{filename} the content of a sysfs attribute.
# %% the '%' char itself.
# There are a number of modifiers that are allowed to be used in some of the
# fields. See the udev man page for a full description of them.
# global stuff
# default permissions for all block devices
SUBSYSTEM="block", GROUP="disk"
# CD/DVD symlinks
BUS="ide", KERNEL="hd[a-z]", PROGRAM="/etc/udev/cdsymlinks.sh %k", SYMLINK="%c{1
} %c{2} %c{3} %c{4} %c{5} %c{6}"
BUS="scsi", KERNEL="sr[0-9]*", PROGRAM="/etc/udev/cdsymlinks.sh %k", SYMLINK="%c
{1} %c{2} %c{3} %c{4} %c{5} %c{6}"
BUS="scsi", KERNEL="scd[0-9]*", PROGRAM="/etc/udev/cdsymlinks.sh %k", SYMLINK="%
c{1} %c{2} %c{3} %c{4} %c{5} %c{6}"
# ide block devices
BUS="ide", KERNEL="hd*", PROGRAM="/etc/udev/ide-devfs.sh %k %b %n", SYMLINK="%c{
1} %c{2}"
# permissions for IDE CD devices
BUS="ide", KERNEL="hd[a-z]", SYSFS{removable}="1", PROGRAM="/bin/cat /proc/ide/%
k/media", RESULT="cdrom*", NAME="%k", GROUP="optical"
# permissions for SCSI CD devices
BUS="scsi", KERNEL="sr[0-9]*", SYSFS{type}="5", NAME="scd%n", GROUP="optical"
BUS="scsi", KERNEL="sg[0-9]*", SYSFS{type}="5", NAME="%k", GROUP="optical"
# permissions for IDE floppy devices
BUS="ide", KERNEL="hd*", PROGRAM="/etc/udev/ide-floppy.sh %k", RESULT="floppy",
NAME{all_partitions}="%k", GROUP="floppy"
# permissions for removable devices like cardreaders or sticks
BUS="usb", KERNEL="sd*", PROGRAM="/etc/udev/usb-storage.sh %k", RESULT="1", NAME
="%k", GROUP="storage"
# permissions for ide storage like pcmcia card readers
BUS="ide", KERNEL="hd*", PROGRAM="/etc/udev/ide-storage.sh %k", RESULT="1", NAME
="%k", GROUP="storage"
# permissions for SCSI scanners
BUS="scsi", KERNEL="sg[0-9]*", SYSFS{type}="6", NAME="%k", GROUP="scanner"
# pty and tty legacy devices
KERNEL="pty[a-z][a-z,0-9]*", NAME="legacy/%k"
KERNEL="tty[a-z][a-z,0-9]*", NAME="legacy/%k"
# md block devices
KERNEL="md[0-9]*", NAME="md/%n"
# device-mapper
KERNEL="device-mapper", NAME="mapper/control"
# floppy devices
KERNEL="fd[0-9]*", NAME="fd%n", SYMLINK="floppy/%n fd%nu1440 fd%nu720 fd%nh1200
fd%nu360", GROUP="floppy"
# tty devices
SUBSYSTEM="tty", GROUP="tty"
KERNEL="tty[0-9]*", NAME="vc/%n"
KERNEL="ttyS[0-9]*", NAME="tts/%n", SYMLINK="ttyS%n"
KERNEL="ttyUSB[0-9]*", NAME="tts/USB%n"
# vc devices
KERNEL="vcs", NAME="vcc/0"
KERNEL="vcs[0-9]*", NAME="vcc/%n"
KERNEL="vcsa", NAME="vcc/a0"
KERNEL="vcsa[0-9]*", NAME="vcc/a%n"
KERNEL="ptmx", MODE="0666"
KERNEL="tty", MODE="0666"
# video devices
SUBSYSTEM="video4linux", GROUP="video"
KERNEL="dvb*", PROGRAM="/etc/udev/dvb.sh %k", NAME="%c", GROUP="video"
KERNEL="nvidia*", GROUP="video"
KERNEL="card[0-9]*", NAME="dri/%k", GROUP="video"
KERNEL="3dfx*", NAME="%k", GROUP="video"
# v4l devices
KERNEL="video[0-9]*", NAME="v4l/video%n", SYMLINK="%k", GROUP="video"
KERNEL="radio[0-9]*", NAME="v4l/radio%n", SYMLINK="radio%e", GROUP="video"
KERNEL="vbi[0-9]*", NAME="v4l/vbi%n", SYMLINK="%k", GROUP="video"
KERNEL="vtx[0-9]*", NAME="v4l/vtx%n", SYMLINK="%k", GROUP="video"
# dm devices (ignore them)
KERNEL="dm-[0-9]*", NAME=""
# i2c devices
KERNEL="i2c-[0-9]*", NAME="i2c/%n", SYMLINK="%k"
# loop devices
KERNEL="loop[0-9]*", NAME="loop/%n", SYMLINK="%k"
# ramdisks
KERNEL="ram[0-9]*", NAME="rd/%n", SYMLINK="%k"
# framebuffer devices
KERNEL="fb[0-9]*", NAME="fb/%n", SYMLINK="%k", GROUP="video"
# misc
KERNEL="rtc", NAME="misc/%k", SYMLINK="%k", GROUP="audio", MODE="0664"
KERNEL="nvram", NAME="misc/%k", SYMLINK="%k"
KERNEL="psaux", NAME="misc/%k", SYMLINK="%k"
KERNEL="agpgart", NAME="misc/%k", SYMLINK="%k" GROUP="video"
KERNEL="uinput", NAME="misc/%k", SYMLINK="%k"
KERNEL="random", MODE="0666"
KERNEL="urandom", MODE="0444"
KERNEL="mem", MODE="0640", GROUP="kmem"
KERNEL="kmem", MODE="0640", GROUP="kmem"
KERNEL="port", MODE="0640", GROUP="kmem"
KERNEL="full", MODE="0666"
KERNEL="null", MODE="0666"
KERNEL="zero", MODE="0666"
KERNEL="sgi_fetchop", MODE="0666"
KERNEL="sonypi", MODE="0666"
KERNEL="inotify", NAME="misc/%k", SYMLINK="%k", MODE="0666"
# sound devices
# alsa devices
SUBSYSTEM="sound", GROUP="audio"
KERNEL="controlC[0-9]*", NAME="snd/%k"
KERNEL="hw[CD0-9]*", NAME="snd/%k"
KERNEL="pcm[CD0-9cp]*", NAME="snd/%k"
KERNEL="midi[CD0-9]*", NAME="snd/%k"
KERNEL="timer", NAME="snd/%k"
KERNEL="seq", NAME="snd/%k"
# oss devices
KERNEL="audio*", NAME="sound/%k", SYMLINK="%k"
KERNEL="dmmidi*", NAME="sound/%k", SYMLINK="%k"
KERNEL="admmidi*", NAME="sound/%k", SYMLINK="%k"
KERNEL="dsp*", NAME="sound/%k", SYMLINK="%k"
KERNEL="adsp*", NAME="sound/%k", SYMLINK="%k"
KERNEL="midi*", NAME="sound/%k", SYMLINK="%k"
KERNEL="amidi*", NAME="sound/%k", SYMLINK="%k"
KERNEL="mixer*", NAME="sound/%k", SYMLINK="%k"
KERNEL="sequencer*", NAME="sound/%k", SYMLINK="%k"
# input devices
KERNEL="mice", NAME="input/%k", MODE="0644"
KERNEL="mouse*", NAME="input/%k", MODE="0644"
KERNEL="event*", NAME="input/%k"
KERNEL="js*", NAME="input/%k", MODE="0664"
KERNEL="ts*", NAME="input/%k"
KERNEL="uinput", NAME="input/%k"
# USB devices
KERNEL="hiddev*", NAME="usb/%k"
KERNEL="auer*", NAME="usb/%k"
KERNEL="legousbtower*", NAME="usb/%k", MODE="0666"
KERNEL="dabusb*", NAME="usb/%k"
BUS="usb", KERNEL="lp[0-9]*", NAME="usb/%k"
BUS="usb", KERNEL="ttyUSB*", SYSFS{product}="Palm Handheld*", SYMLINK="pilot"
# printer devices
SUBSYSTEM="printer", GROUP="lp"
# netlink devices
KERNEL="route", NAME="netlink/%k"
KERNEL="skip", NAME="netlink/%k"
KERNEL="usersock", NAME="netlink/%k"
KERNEL="fwmonitor", NAME="netlink/%k"
KERNEL="tcpdiag", NAME="netlink/%k"
KERNEL="nflog", NAME="netlink/%k"
KERNEL="xfrm", NAME="netlink/%k"
KERNEL="arpd", NAME="netlink/%k"
KERNEL="route6", NAME="netlink/%k"
KERNEL="ip6_fw", NAME="netlink/%k"
KERNEL="dnrtmsg", NAME="netlink/%k"
KERNEL="tap*", NAME="netlink/%k"
# CAPI devices
KERNEL="capi", NAME="capi20", SYMLINK="isdn/capi20"
KERNEL="capi*", NAME="capi/%n"
# Network devices
KERNEL="tun", NAME="net/%k"
# raw devices
KERNEL="raw[0-9]*", NAME="raw/%k"
# kbd devices
KERNEL="kbd", NAME="%k", MODE="0664"
# packet devices
KERNEL="pktcdvd", NAME="pktcdvd/control", GROUP="optical", MODE="0660"
KERNEL="pktcdvd[0-9]*", NAME="pktcdvd/pktcdvd%n", GROUP="optical", MODE="0660"
pacman -Qi udev
Name : udev
Version : 057-1
Groups : None
Packager : maci <[email protected]>
URL : http://www.kernel.org/pub/linux/utils/kernel/hotplug/udev.html
License : None
Architecture : i586
Size : 301287
Build Date : Mon Apr 18 03:00:55 2005 UTC
Install Date : Sat Apr 23 19:59:26 2005 UTC
Install Script : Yes
Reason: : explicitly installed
Provides : None
Depends On : coreutils hotplug
Required By : None
Conflicts With : None
Description : The userspace dev tools (udev)
Hope that helps. -
I have a Compaq Proliant 1600 PII 450. the installation hangs. any ideas ?
Hi,
Can you tell me at what stage it hangs? Which version of Solaris ur trying to install? And if u could give more informations that will help to solve ur problem.
Ramesh ([email protected]) -
Compaq Presario SR1235IL Installation Problem
Sir,
I am using Compaq Presario SR1235IL Desktop PC from last few years. Present Display Chip problem in Mother Board I have install new Display Card, After install the Display Card trying to system is install new OS, but, after coping the system files and restart the system, second step of coping files is not opening automatically system is shown blank screen so many times trying to install OS same problem repeat. Please send the how to format the desktop PC, If any changes of BIOS pls send the details.Hello seinus. I understand you're trying to reinstall Windows on your computer.
Are you trying to install via a Windows installation disc?
If you're trying to perform the recovery with a disc I suggest trying the F11 method. Try these instructions to perform the F11 recovery.
If this also fails I think it is going to be a good idea to test your hard drive for problems. You can use the built in diagnostics to check the hard drive. This document has instructions. Please make sure to post the results.
If this is helpful or you want to say thanks make sure to click the white star under my name to give me Kudos. It is greatly appreciated.
I'll be keeping an eye out for the results of these suggestions. I hope you have a great day!
Please click the white star under my name to give me Kudos as a way to say "Thanks!"
Click the "Accept as Solution" button if I resolve your issue. -
CallManager on Compaq Proliant DL580
Hi Guys,
I read the post with the same subject, but, the post is old. My Customer have a CUCM 8.6.2 install about VMWare 5.1 EsXi in the hardware DL-580 GL. I would like know if this solution is approved to install CUCM.
Thank You,
WilsonYou have to look at the 3rd-party server / specs-based column (at top) and walk through the requirements and links. All vendors are now supported; however, a given server must meet specs for various components. You need to know the details of what is in the HP server and compare to what is required to be supported. You won't see a list of "Server A" is supported, "Server B" is not.
Hailey
Please rate helpful posts!
Maybe you are looking for
-
OBIEE only getting limited number of group membership records
Hey everyone, I'm seeing some strange behavior with the group membership functionality of OBIEE. Right now we're on version 10.1.3.2 and we've implemented SSO and we setup a query against LDAP (AD) to get user group information similar to the way Ven
-
BAPI to unaccept service entry sheet
Hello, I have created and accepted service entry sheet using BAPI "BAPI_ENTRYSHEET_CREATE". Now i have requirement where I need to unaccept already accepted service entry sheet. Can any one provide me the BAPI which will help me in resolving this iss
-
I followed all instructions, help topics, etc., and flashplayer still does not function. (IE 10). Who can I talk to for help?
-
Launchpad search not working mavericks
Search not working on mavericks under launchpad. Normally you can click into the search bar on launchpad, or just start typing to filter/find. Under mavericks I can no longer do this. The search bar is inert, does not respond to typing or clicking wi
-
Few quick questions - We have all CISCO VoIP equipment and just want to know what the best option is for a compatible cordless telephone with multiple handsets? Please help....Thanks!