Compatibility between ASR9K and SFP-H10GB-ACU10M

Hi Everyone,
I have in my environment two ASR9K with module A9K-16T/8-B and I am trying to connect using the Active Twinax cable 10M (SFP-H10GB-ACU10M), however when I connected the cable, shows the following error:
State:
Administrative state: enabled
Operational state: Down (Reason: Security failure (not a valid part))
LED state: Red On
Phy:
Media type: Not known
Optics:
Vendor: CISCO-TYCO
Part number: 2163675-2
Serial number: TED1618U0H0
I checked the compatibility list and apparently okay, as shown in the link below:
http://www.cisco.com/c/en/us/products/collateral/routers/asr-9000-series-aggregation-services-routers/data_sheet_c78-624747.html
Please, the community can help me?
Best Regards,
Vitor Nakano

The twinax copper 10 Gig SFPs such as the one you cite are prefabricated cables with transceivers already attached. See the pictures on the top left of the data sheet to visualize what you get.
Controlling that mating of transceiver to the copper media is how they are able to ensure reliable operation at 10 Gbps over copper.

Similar Messages

Sfp-h10gb-acu10m compatibility

Dear all,
Does anybody know if SFP-H10GB-ACU10M cable is compatible with Cisco Catalyst 2960-S series? According to the compatibility matrix it is not compatible with Cisco IOS release 12.2 (53) SE1, but i would like to know if it would be compatible with another IOS version.
Thanks in advance,
Carmen

I suspect it might have something to do with the CVR-X2-SFP10G, seeing that the converter module data sheet also does not list any length of the Active Twinax cables being compatible.
I am trying to reach out to someone within the Product Mgmt org to see if they can provide an answer... but my contacts are old....

Connecting OC48 Between ASR9K and ASR1K

Hi there.
I don't know the first thing about the WAN something like POS...
Now I'm facing some problem with connecting OC48(POS) between ASR9K and ASR1K.
There are new 9K and new 1K in same server rack for the test.
So i tried to test these for connecting OC48
9K and 1K is directly connected by OC48
9K : A9K-SIP-700 // SPA-2XOC48POS/RPR // SFP-OC48-SR
1K : ASR1000-SIP10 // SPA-1XOC48-POS // SFP-OC48-SR
After connecting these two devices directly, ASR1K shows the interface status is up/up
but ASR9K ... the interface status is down/down.
I didn't configure anything. Do i need to configure something ?
When i connected POS port 1 and POS port 2 directly in the same ASR 9K chassis, the interface is up/up
please help me out
Thank you in advance. :)

exactly, so the transmit side of the 9k needs to be connected to the receive side of the 1k.
the transmit side of the 1k needs to be connected to the receive side of the 9k.
download this doc for reference:
http://www.cisco.com/c/en/us/td/docs/interfaces_modules/shared_port_adapters/install_upgrade/ASR1000/asr_sip_spa_hw/ASRsov.html#pgfId-1136398
Another link discussing the type of testing you are attempting:
http://www.cisco.com/c/en/us/support/docs/optical/synchronous-optical-network-sonet/16181-posclocking-16181.html

SFP-H10GB-ACU10M

Dear All,
does SFP-H10GB-ACU10M come with SFP+ connectors?
or it is just a cable and we need to provide the SFP+ Transceivers??
thanks

The twinax copper 10 Gig SFPs such as the one you cite are prefabricated cables with transceivers already attached. See the pictures on the top left of the data sheet to visualize what you get.
Controlling that mating of transceiver to the copper media is how they are able to ensure reliable operation at 10 Gbps over copper.

I have a web site built by Yahoo Web Site Builder which does not have a Mac version, is there any compatability between Iweb and the old Yahoo program?

I have a web site built by Yahoo Web Site Builder which does not have a Mac version, is there any compatability between Iweb and the old Yahoo program? If not how do I clear off the old site so as to re publish with Iweb.

iWeb cannot import published files so you would need rebuild the site.
Yahoo hosting is notoriously poor and their tech support is awful. I would suggest you look for new hosting and start afresh. Some pointers for choosing hosting...
http://www.iwebformusicians.com/iWeb/Website-Hosting.html
If you do choose to go this route, transfer your domain name registration away from Yahoo to your new host.

Battery compatibility between X31s and X61s

Hi!
I own a X31s and X61s, and would like have a spare battery handy for travel. Before placing the order, I am wondering if the following battery can be used on both:
* ThinkPad X60s Series 4 Cell Slim Line Battery
It is not cheap, so I would like to think twice before buying. Somehow I cannot find any information on the compatibility issue. Thank you for your help!
Jenny

jennyumaa, welcome to the forum,
unfortunately the batteries are definitely not interchangeable between X31 and X61 systems.
Sorry
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Compatability between LaCie and other drives

Greetings Kind MacAddicts!
I have a 160GB LaCie (Triple Threat?) FW800 external drive and have had no problems. Now I want to expand and daisychain another external drive. Thinking of a Maxtor with FW800 (more bang for the buck) and wondering if there are any known compatability issues between LaCie and Maxtor, or btw Maxtor and the new Intel processors. Suggestions?

Well that drive inside the LaCie casing could very well be a Maxtor drive too :P
Remember LaCie don't actually make Hard Drives, they just put drives from other manufacturers in their external casings and charge a premium.
Yes, some of their designs look nice

4500x VSS and SFP-H10GB-CU1M

Hello
I have (2) Cisco 4500x with a VSS config. I als have a couple cables "SFP-H10GB-CU1M".
I want to make sure I have this physically setup correctly. I have searched but not found anything specific enough.
Please review and advise.

Yes, all device packages are installed (including 7.0) and the Pi 2.1.2 patch.
Info from "ifm_config_archive.log" when trying Archive the Configuration:
[2014-12-09 19:58:11,300] [pool-37-thread-5] [service] [ERROR] - Thread Id : [9,460] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching VLAN file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]'
Maybe the Prime don't know where to find the vlan.dat on the 4500X-VSS ?
#dir cat4000_flash:
Directory of cat4000_flash:/
1 -rw- 2236 <no date> vlan.dat
sysObjectID (1.3.6.1.2.1.1.2) is
.iso.org.dod.internet.private.enterprises.cisco.ciscoProducts.cat4xxxVirtualSwitch
That is not the expected and supported value "4500X-16" above
Update: Error on fetching running and startup config as well:
[2014-12-09 20:24:21,818] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching RUNNINGCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]
[2014-12-09 20:25:31,882] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching STARTUPCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]

Compatibility between Yosemite and Photoshop / Bridge CS5.

I am concerned about the possibility of incompatibility between Yosemite and Photoshop / Bridge CS5 so have delayed updating my Mac. Has anyone updated, experienced problems and found solutions? What does Adobe have to say in this regard?

I'm not sure I know enough to answer the question.
The images are on my G5 on a second internal hard drive (not the boot drive).
They are in a folder with a lot of images from the same shoot.
That folder shows up in the Library in Aperture, also. I think I imported them. But, as best I can tell, they do not "only exist in Aperture" because I can see them, and their .xmp files in the original file on the second internal hard drive.
Thank you so much for trying to help.
sjh

Issue with VPN compatibility between 2811 and 2911

hello
I would like to ask anyone have had any issues with setting up a VPN tunnel between 2811 and 2911?
The IPSec VPN is established but for some reason I cannot ping the LAN side to the other LAN side of the other end of the VPN Router?
Any experience would be much appreciated
Thanks

IPSec VPN can be with no problem set up between any cisco routers (and not nesesserely cisco), so there are should be no issues in your case.
If you say that tunnel is established successfully, then problem most probably related to routing issues between sites or incorrect crypto-acl configured. Check if hosts on both sites have correct routing information on how to get to subnets on the other site.
To make more accurate assumptions it would help if you provide config on both sites and describe your topology.

USB Flash Drive Compatibility between Mac and PC?

Hi,
I own an iMac 2 GHz Intel Core 2 Duo 1 GB 667 MHz DDR2 SDRAM and just got a new job where I'm using a PC. At work they all use flash drives to transfer data back and forth to computers etc. Would a flash drive (let's say a Kensington since that's the brand I've seen the most at work) that works in a PC at work be compatible with my iMac at home. I know Kensington makes them compatible for Mac and PC but just wondering how the data would transfer onto my Mac. Is it readable, does it depend what I'm transferring over?
Message was edited by: spiralgirl

{quote} guy there said they haven't yet perfected the flash drives to switch between Mac and PC and work well so I was a little surprised at this. {quote}
That is pretty much a standard reply you get from someone that doesn't know anything about macs. I've used those things for years without any problems, but I have been using my ipod as a disk lately because I always have it with me. It's also another less thing I have to buy and carry around.

Compatibility between CF7 and CF10

Hi
We currently have two load-balanced servers running CF7 Enterprise Edition. The applications use the Client Variable store, so that we can move users between servers as necessary (should one become busy / unavailable).
We now want to add a third server into the cluster. This will have to be CF10 Enterprise Edition.
Does anyone know if the Client Variable store operates in the same way, or am I likely to have problems if I try and add this to the cluster? Also, can anyone point me in the direction of looking at which CF tags (or tag attributes) have been deprecated between 7 and 10?
Thanks
Karl

I don't think you will find a list of differences between CF 7 and CF 10 from Adobe. Maybe someone out there has compiled a list???? More likely you will need to read the release notes from each version and determine that way.
ColdFusion release notes - http://www.adobe.com/support/documentation/en/coldfusion/releasenotes.html

File compatibility between cs3 and cs5

Hi,
What are the compatilibity issues between Photoshop CS3 and CS5? Can they be used together without much (if any) issues?
Thanks.

They can happily coexist on the same system, as long as you've got the disk space. Photoshop has always been like that.
You'll only be able to run one at a time, at any given instant, though.
Regarding file compatibility, I don't how much it's required to open a file in Photoshop CS3, but the newer version does offer a "Maximize Compatibility" preference setting for saving .psd files. On occasion I've opened .psd files in Photoshop CS3 saved by CS5 (using the aforementioned setting) and I haven't seen any issues at all.
-Noel

Compatibility between CS3 and earlier versions?

As the web developer I have Contribute version 3, but some of
my new clients
will be buying the latest Contribute CS3 to update their site
pages. Can I
still set up their roles and editing rights for a site and
create a
connection key to send to them that will work for them in
Contribute CS3
without difficulty? And can either of us still edit the site
pages,
regardless of the fact that we are each using different
versions of
Contribute?
In conclusion, are there any backward compatibility issues I
should be aware
of between the newer version and older versions of CS3 when
administering,
and connecting to, the same website?
Thanks in advance.
(Please reply to forum. E-mail address is bogus to prevent
spam)

Thanks for the advice.
"ThinkInk" <[email protected]> wrote in
message
news:f0sa43$dvh$[email protected]..
>I had the same problem when C4 arrived and I could'nt
purchase C3 for my
> clients.
>
> The key is to use Transitional Mode (adminstrator
settings,
> compatibility),
> here's wat the HELP says:
>
> --------------------------
> Enabling compatibility with older versions of Contribute
> Contribute 4 offers administrators two compatibility
options--one that
> allows
> users with earlier versions to work on the website, and
one that does not:
>
> Transition Mode
> In this mode, users of earlier versions of Contribute
can continue working
> on
> the website, along with Contribute 4 users. This lets
you evaluate the new
> version and set up new roles and permissions without
disrupting users with
> earlier versions of Contribute.
>
> Compatibility Mode
> In this mode, all users must use Contribute 4. Users
with earlier versions
> cannot work on the website.
>
> Contribute 4 starts in Transition mode by default when
you migrate from
> Contribute 3. Use this mode temporarily; when you?re
ready, transition all
> users to Contribute 4 and enable Compatibility Mode.
>
> To enable Compatibility Mode:
> In Contribute 4, select Edit > Administer Websites,
and then select a
> website.
> The Administer Website dialog box appears.
>
> Select Compatibility from the category list on the left.
> The Compatibility options appear in the Administer
Website dialog box.
>
> Select Compatibility, and then click Close.
> After you enable Compatibility Mode, all users connected
to the website
> must
> use Contribute 4.
>
> ------------------------
>
> It's really better to upgrade yourself to the newest
version, so you know
> what
> extra options your clients have and you can support
them. I managed to get
> both
> C3 en C4(I purchased the upgrade) running on my PC, so
maybe that's also
> an
> option.
>
> grtz. Hayo
>

Backwards compatibility between DWCS3 and DW8

I am purchasing the CS3 Web premium and plan to only install
in on the new desktop I will purchase. Most of my design work will
be done on that system but I will occasionally need to work on
files when traveling on my laptop which will only have DW8 (not
upgrading that system just yet). Will there be any compatibility
issues in working on the same file between both versions, or am I
stuck only working on the desktop?
Dara

I don't see any problem with compatibility if they are static
pages and you
haven't used any of the newer features from CS3 like Spry for
example.
Nadia
Adobe® Community Expert : Dreamweaver
CSS Templates |Tutorials |SEO Articles
http://www.DreamweaverResources.com
~ Customisation Service Available ~
http://www.csstemplates.com.au
"Dara_BSI" <[email protected]> wrote in
message
news:f3o93g$ert$[email protected]..
>I am purchasing the CS3 Web premium and plan to only
install in on the new
> desktop I will purchase. Most of my design work will be
done on that
> system but
> I will occasionally need to work on files when traveling
on my laptop
> which
> will only have DW8 (not upgrading that system just yet).
Will there be any
> compatibility issues in working on the same file between
both versions, or
> am I
> stuck only working on the desktop?
>
> Dara
>

Compatibility between ASR9K and SFP-H10GB-ACU10M

Similar Messages

Maybe you are looking for