Compatibility between Inspiron 15R N5010 (5010-7015) and WD black^2 (WD1001X06XDTL) dual drive 2.5''

Hello,
I own a Dell Inspiron 15R N5010 (5010-7015) / i5 / 4GB RAM / 320GB HDD and I am interested in upgrading the internal hard drive to the dual drive series from WD (black^2 - WD1001X06XDTL).
The system supports SATA2 and a variety of capacities between 160GB and 640GB for 5400rpm and only for 320GB and 500GB on 7200rpm according to the manual.
Is there any possibility that I could upgrade to a WD Black2, or I will face compatibility issues?
Does the specific model (N5010) support that technology? The only list I was able to find was this one: http://wdc.custhelp.com/app/answers/detail/a_id/11024/~/wd-black%C2%B2-dual-drive-computer-compatibility-list
If not, are there any other alternatives for a hard drive upgrade [i.e. Seagate 1TB Laptop SSHD (STBD1000400)] that would have full compatibility?
As you can see I am looking for anything as close to an SSD but not an SSD.

The Black2 functions as any standard SSD and hard drive -- as long as the OS you're running supports it (it's software-controlled), you're set. It'll work with Windows 7 or Windows 8, no problem. It won't (unless something has recently changed) work with Linux, though.

Similar Messages

Inspiron 15R N5010 Noise then crashes with blue screen and shuts down.

I have heard this is a common problem with dell laptops. And it has never been addressed to. I'm hoping to get a clear cut answer here.
The issue is already mentioned here by many users, and all over the web too.
Please,
I would like to know if it can be fixed, or should I scrap my Laptop,since its onboard graphics.
In case its a driver issue,
Can you also point me to a post where this matter has been addressed to successfully.
I've performed diagnostics many times. After a few tries it gets the laptop going for a while. Then the problem appears again.
Thanks

If it beeps then read this article: HP BIOS beep codes.
Try this bootable memory diagnostic disk: Download memtest86 iso file and burn it to disk using Imgburn.
Try this procedure:
Unplug the PC and open it up. Clean out all the dust. Carefully remove and replace all the cables going to the motherboard one at a time. Do the same for the memory dimms and the video and sound cards if you have any. Plug your PC back in a give it a go.
You might want to inspect your motherboard for heat damage using a flashlight.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Plug in compatability between BW plugin in R/3 and BI - R/3 upgrade to ECC6

Hello,
we are running SAP NetWeaver BI 7.0 Release 700 Patch 19.
Our underlying R/3 system is still 4.6C with plugin 2004_1_46C ( yes, I know it is time )
We are upgrading R/3 to ECC6 with plug in P701 Patch 3.
Questions:
1.) I would like to know where exactly I can see which ECC6 plugin is copmpatible with our BI Version.
2.) Did anyone who has upgraded to ECC6 experience any particular issues when upgrading the plugin?
3.) Sense check of approach - so far the simplistic idea from a BW perspective is:
New R/3 system has been created and connected to BW :
1.)     In BW ACTIVATE SOURCE SYSTEM
2.)     In source system connection option : Replicate datasources and activate
3.)     Transfer global settings u2013 first simulate then update tables u2013 no rebuild should be necessary
Before the Plugin P 701 in the R/3 ( ECC6 ) system can be upgraded the BW delta queues need to be cleared in the source system ( R/3.)
4.)     Clear out V3 queue either via BW as part of the jobplan ( or manually via RSA7 but would mean loss of data )
5.)     After run of batch schedule during posting free period check in RSA7 for entries in delta queue - should be empty
                     now.
6.)     Does the clearing of the delta might need to be run twice to clear the queue completely ?????
8.)                 Deactivate logistics cockpit via SBIW ...LEBW ( is this mandatory ? )
9.)                 If delta queues are empty and the logistics cockpit is deactivated then upgrade the plug ins in R/3
10.)               Then repeat step 1-3 and reactivate the logistics cockpit again
Is this it?
Many thanks for advise on this.
Regards
ChrisAC

SAP Note : 153967 and
https://service.sap.com/r3-plug-in should give some information on plug in compatibility...
8.) Deactivate logistics cockpit via SBIW ...LEBW ( is this mandatory ? ) - I think you just need to desachedule the collection jobs alone and not deactivate the LO Extractors and activate them once again...
Edited by: Arun Varadarajan on Oct 9, 2009 11:43 PM

Compatability between Forms 6(Forms 6i also) and Oracle Database 10g

Hai All,
I want to know Any Compatible issue between ORACLE FORMS 6 (ORACLE FORMS 6i also ) and Oracle Database 10g .
Any special patches, parameters needed?
Any white paper describing this document.
Please help?
shiju

Forms 6i Patches pre 16 and 10g databases - many problems
Forms 6i Patch 17 - 10g DB Rel.1 - certified
Forms 6i Patch 18 - 10g DB Rel.2 - certified only for E-Business-Suite-user

Nican backwards compatibility between nican versions 2.1.3 and 2.6

Hello folks,
I have inherited a VC++ application that uses nican. It was apparently compiled using nican version 2.1.3 (assumed to be true because the VC++ program works with nican 2.1.3). We recently installed LabVIEW 8.6 (including nican 2.6) and the VC++ program no longer worked. After uninstalling nican 2.6 and reinstalling 2.1.3 the program works again. This is fine except that for new development, we would like to use the nican 2.6 (the latest we presume?)
This raises a couple of questions:
1. Is nican 2.6 expected to be backwards compatible with 2.1.3?
2. If the answer to the question above is "yes", then can anyone offer any suggestions on why the VC++ program would no longer work when nican 2.6 was installed?
3. If nican 2.6 is not backwards compatible with nican 2.1.3, where can I find the necessary documentation (e.g. well documented .h files etc) to begin trying to decipher what is and isn't compatible so I can make the necessary changes?
Any help is greatly appreciated.
Best Regards,
Chris

Hello B2k,
Thanks for the information. I wasn't too sure where to start, so I don't have any more information yet. The application does not report any errors, it just doesn't "do" anything. For example, when I connect to the UUT using the VC++ application, the first thing I would normally do is read the EEPROM (over CAN), but this doesn't work with NICAN 2.6 installed.
It looks like NI-Spy may very well help me determine where (i.e. what calls) are failing, thanks.
1. Do you know where NICAN 2.6 puts nican.dll and nican.h?
2. You explicitly stated that NICAN 2.6 should be backwards compatible with 2.1.3, but IF something has changed in the interface (e.g. a function signature etc.) do I need to search the nican.h files to try to find the difference, or do you know of another document that lays them out more clearly? (I found several documents/revisions on the NI website (e.g. "NICAN Programmer Reference Manual" and "NICAN Hardware and Software Manual and Specifications"), but I don't have any idea which document/revision goes with which version of NICAN?
Thanks for your time and the helpful information!
Chris

Compatibility Between Audigy 2 Drive and Audigy 2 ZS GAMER C

Greetings,
I had a question about compatibility between an Audigy 2 Dri've and an Audigy 2 ZS Card.
Specifically, the Sound Blaster Audigy 2 Platinum Sound Card and the Sound Blaster Audigy2 ZS GAMER Edition Sound Card (SB0350).
Is the Audigy2 ZS GAMER Sound Card compatible with the Audigy 2 Platinum Dri've?
If this particular question has already been addressed in another thread, my apologies.
Thanks,
Benwajones

I searched (on "external" and "bay," but not "dri've" before I posted) but did not see this message. Is the reverse possible - that is a Audigy original dri've and an Audigy 2ZS sound card?

Compatibility between Java crypto and open ssl

Hello
I have some question about compatibility between java crypto and openssl library.
This is my case:
1.I created DESede key and stored it to file:
SecretKey key = KeyGenerator.getInstance("TripleDES").generateKey();
File f = new File("c:\\key.dat");
DataOutputStream dos =new DataOutputStream(new FileOutputStream(f));
dos.write(key.getEncoded());
dos3.close();2.I encrypt some file "c:\\normal.dat" through:
ecipher.init(Cipher.ENCRYPT_MODE, key2);
byte[] enc = ecipher.doFinal(normalData);
File f2 = new File("c:\\enc.dat");
DataOutputStream dos =new DataOutputStream(new FileOutputStream(f2));
dos.write(enc);
dos.close();

You have carefully left out some critical java code, namely the Cipher.getInstance() method. You'll notice in the documentation for this method that there 3 components to the "transform" argument of this method, the algorithm, the mode, and the padding. All of these must match exactly with the what openssl is using. Furthermore, if you are using one of the modes which require an IV, like CBC mode, then this must match exactly too. If you don't explicitly specify some of these parameters, you might get default values supplied. It is up to you to find out what these are.

I like ti known about compatibility between Windows 8 and iTunes

I like ti known about compatibility between Windows 8 and iTunes

It works for some and not for others.
At this time, there is no publicly available version of iTunes that is supported on Windows 8.
Only Apple knows when that will change.

Compatibility between MSI i7 boards and Corsair DDR3 RAM kits?

Similar issues from other posters: Thread 1, Thread 2
Are there any known compatibility issues between MSI's Intel i7 boards and Corsair's 1600 DDR3 triple-channel kits?
My brother's machine (which has been discussed here before last time I tried to fix it) is still having trouble, and also uses the same type of RAM as the two threads above. The symptoms are:
1) Occasional lockups, followed by a reboot
2) Inability to POST: the machine will try numerous times, rebooting each time (as in threads 1 and 2), followed (eventually) by the POST saying "the previous overclocking has failed and the BIOS is reset to default settings" - as in thread 1. The machine will then (normally) boot. Reducing the RAM speed increases the chance of a successful boot, but the settings don't stick (presumably they are wiped when the BIOS is reset to the default settings). Cold boots (after the machine has been switched off overnight) tend to be the most likely to fail.
Any ideas what could be causing this, if not an incompatibility with the RAM (in 3-channel mode)? Dropping down to one stick stabilises the system, but at the expense of dropping to a mere 2GB of RAM.

Quote from: HU16E on 06-September-09, 15:10:01
Out of seven MSI X58 boards, none had a problem with Corsair sticks. With the 1600's running at 1066, they should only require default (1.50v) auto voltage. They should also work using settings of 1N 9 9 9 24 without issue. As the CPU IMC only natively supports 800/1066, your particular CPU may have a limitation of working any higher. But, something is not right within the system if it will not run the RAM at 1066. To rule out a bad stick, test with just one in the black A0 slot, & swap it out & test the other two individually. As far as DRAM voltage, if all the sticks check out ok, try raising it to 1.55V. Keep the forum updated on your progress.
Added: Make sure 'Spread Spectrum' is disabled in bios Cell Menu, as well as 'Extreme Memory Profile' if your bios has it listed.
Are they 2GB sticks? (All the threads in question use the 2GB sticks - one 3×, and one 6×)
Back around the time I tried the BIOS flash as the solution, I Memtest86'd each of the sticks individually in the MSI-recommended slot for a single-stick configuration, and each tested perfectly. Part of the advice given at the time was to disable XMP and Spread Spectrum; they already were.
Whilst I can't be certain that the RAM is the problem, at least three threads on this board now are using 2GB Corsair 1600 sticks and having strikingly similar symptoms...
I'll try investigating the voltages later today. Thanks!

Compatibility between CRM 4.0 and IS-U 4.64

Hi,
My company is using SAP IS-U 4.64 and is studying the use of SAP CRM. Does there is any problem of processus compatibility between these two versions ?
I don't find any document on the market place or in sdn. Does there is a document that shows the optimization for cross application use of SAP ?
Thanks
Thomas

Hi Gaurav,
I've dealt with both realities (specially in IC Webclient) and from the configuration point of view and in my opinion, it is basically the same.
For me the main change is that, in IC webclient scenario, instead of you do some customizing in a XML code, in CRM5 you'll do it by configuring tables.
In CRM5, you'll have some nice functionalities that CRM4 doesn't have (e.g.: You can choose with channels your transactions are allowed, Email Workbench, ERMS categorization is time dependent, and so on...), but the big jump is given when you compare CRM5 to CRM6 (or CRM 2007).
Kind regards,
Bruno

Compatibility between R/3 4.6c and BI 7.0

Hello,
First of all, I want to stress out that I just spent hours reading SDN and service marketplace, and I just couldn't find a precise answer, so that's why I ask you this ..
we have SAP R/3 4.6c, SP 23, no BW sofar.
We plan to have BI 7.0, and I have been asked to which SP level we had to be in SAP R/3.
I understand that we have to get the right PI version ( PI 2004.1 SP10 if I'm right ?), but what about the SP level of SAP R/3 itself ??
Thank ou very much if you can help.

Hi Andreas,
Thank you for your quick answer !
In fact I had already read this thread...So I did the 'R/3' search, and read it all.
But now maybe I am a little bit more stupid than I thought, because when I read the compatibility matrix between SAP R/3 SP level and netweaver here :
https://websmp109.sap-ag.de/~form/sapnet?_SHORTKEY=01100035870000653817&
I just don't understand:" PI 2004.1, with R/3 SP01 (??) and R/3 plug-in SP10 "
So all I understand is I must have the 2004.1 plug-in with SP10 on my SAP R/3 4.6c system..am I right ?
Thanks again

I have a web site built by Yahoo Web Site Builder which does not have a Mac version, is there any compatability between Iweb and the old Yahoo program?

I have a web site built by Yahoo Web Site Builder which does not have a Mac version, is there any compatability between Iweb and the old Yahoo program? If not how do I clear off the old site so as to re publish with Iweb.

iWeb cannot import published files so you would need rebuild the site.
Yahoo hosting is notoriously poor and their tech support is awful. I would suggest you look for new hosting and start afresh. Some pointers for choosing hosting...
http://www.iwebformusicians.com/iWeb/Website-Hosting.html
If you do choose to go this route, transfer your domain name registration away from Yahoo to your new host.

Still no compatibility between Storage Client Library v3 and emulator?

Hi,
According to this blog post:
I'm apparently unable to post a link, but here's the text from the blog. I'm sure you can find it via google if interested.)
<<<<
Storage Emulator Guidance
As mentioned above an updated Windows Azure Storage Emulator is expected to ship with full support of these new features in the next couple of months. Users attempting to develop against the current version of the Storage emulator will receive Bad Request
errors as the protocol version (2013-08-15) is unsupported. Until then, users wanting to use the new features would need to develop and test against a Windows Azure Storage Account to leverage the 2013-08-15 REST version.
>>>>
So it seems there was not compatibility between the storage emulator and Storage Client Library v3. I'm wondering if that is still the case. I get a 400 error when calling container.CreateIfNotExists() when pointing to local storage, but no problem pointing
to production storage. I'm using SCL v3.0.2.
Thanks...
-Ben

Hi,
Please see
http://social.msdn.microsoft.com/Forums/windowsazure/en-US/c961d0df-e6ab-4563-958c-b3646ee2cd9d/the-value-for-one-of-the-http-headers-is-not-in-the-correct-format?forum=windowsazuredevelopment#16892f11-498d-4975-aa4b-adfa12b03fea
Here is a snippet of this thread.
Storage Emulator 2.2 is currently incompatible with Storage Client Library 3.0.0.0. This has been mentioned in Storage Team Blob as well:
http://blogs.msdn.com/b/windowsazurestorage/archive/2013/11/27/windows-azure-storage-release-introducing-cors-json-minute-metrics-and-more.aspx (Please
read "Storage Emulator Guidance" section towards the end of the post).
It may be fixed in the next version.
Hope this helps
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Dell Inspiron 15R and Photoshop CS5?

Currently looking at buying a DELL inspiron 15R for my 16yr old daughter. She is interested in graphic design and will be studing it next year so also getting Photoshop CS5.
Specs I'm looking at are:
Intel® Core™ i3-370M Processor (2.4Ghz, 4Threads, 3M cache)
15.6 Widescreen HD WLED Glossy Display with TrueLife™ (1366x768)
4GB RAM
500GB 7200RPM Hard Drive
Intel® HD Graphics
Does this laptop have the necessary 'grunt' for photoshop. It exceeds system requirement for photoshop CS5. but specs are usually slower than reality.
SHould i update the chip to an i5? Intel Core i5 460M (2.53GHz/3MB cache)
or alternatively should I change the video card to a dedicated card option ATI Mobility Radeon™ HD 5650 - 1GB?
Thanks in Advance.

From my personal experience, I wouldn't go for an Integrated card. This is one of the most important components for Photoshop, so invest in a decent graphics card (ATI or NVidia). It doesn't have to be a really exepensive one - I have been using ATI Radeon with 256MB of RAM on my Dell Studio for almost two years and it still rocks! (even when I work with 3D in Ps CS5 Extended).
I would also invest in more RAM (this can be added easily - I bought extra 4GB as my Studio came with 3GB).
I wouldn't worry about the processor - I'm on Intel Core 2 Duo - and it works very very well, it's very quick which is very important as I'm training Photoshop.
I hope this helps.

Compatibility between the iPhone 6 and certain vehicles, and the hands free connectivity in those vehicles?

How can I findout about the compatibility between the iPhone 6 and certain vehicles, and the hands free connectivity in those vehicles?
I am interested in the iPhone 6 but have several meetings that have to call into for work. Where can I find out about the compatibility with iPhone 6 and if there are issues I need to be aware of for connecting to hands free option in the car?
Please point me to the right direction. The dealership was useless in helping me. I figured Verizon can be more helpful.

ShaM1,
I understand the importance of the bluetooth compatibility between your new device and your car. What make and model is your vehicle?
Here is the information that Verizon Wireless has on Bluetooth Car Kit compatibility; http://www.verizonwireless.com/support/how-to-use-bluetooth-car-kit-compatibility/. However, Apple does not have any information listed here. We can assume that the latest and greatest iPhone 6 has the technology to be compatible with most vehicles. If you'd like to discover further information I'd suggest contacting Apple directly; 800-275-2273.
Let us know if you need anything else!
TrevorC_VZW
Follow us on Twitter @VZWSupport

Compatibility between Inspiron 15R N5010 (5010-7015) and WD black^2 (WD1001X06XDTL) dual drive 2.5''

Similar Messages

Maybe you are looking for