Complete FX5200-T128 failure?

I've just tried installing an FX5200-T128 into a PC266 motherboard (using XP1600+ processor).
The driver install was fine but the end result now is that when I boot I have about two seconds of 640x480 then the signal stops (screen goes blank and says "no signal input").
I have absolutely no idea of how to proceed - the machine still works fine when booting from the old PCI card (which I removed before starting the install - the machine won't boot with both in place) or the built in VGA slot.
I've tried setting the PC's BIOS to using PCI with an IRQ, PCI without and IRQ and just using the "built in AGP" option all with the same result.
Any ideas very welcome.
Thanks

balance,
Have you try to insert your AGP Card to other system ?
maybe is the AGP Card problem.
Regards - Porsche -

Similar Messages

[GeForceFX] S. .O. S fx5200-t128

tengo 14 maquinas con esta graphic card FX5200-T128, 128mb ddr, S-TV_out desde hace 7 meses,
en la ultima semana empesaron a reiniciarse, el disipador de la graphic card toma mucha temperatura produciendo el reinicio, las 14 maquinas estan en las misma condiciones se REINICIAn, necesito ayuda urgente ya que son herramientas de trabajo.-
MOTHERBOARD: asrock K7VM3
PROCESSOR: AMD sempron2400+
256 mb ddr
I have been having 14 maquinas with this graphic card Fx5200-t128, 128mb ddr, S-TV_out for 7 months, in completes week empesaron to be reinitiated, the dissipator of graphic card takes much temperature producing the resumption, the 14 maquinas estan in same the conditions REINICIAn, I need urgent aid since they are work tools. - MOTHERBOARD: asrock K7VM3 PROCESSOR: 256 AMD sempron2400+ mb ddr

Hi, how high the emperature of the cards are? are all of them getting hot? when you say Quote
the dissipator of graphic card takes much temperature
, what exactly do you meant to say? are they over 70° C? what drivers you are using? the latest? fresh windows install? Directx? please provide more info about your PCs
here you can read some info that I guess will help you:
>> General FAQs for MSI SocketA boards <<
Is your problem caused by your PSU?
Suggestions on posting and getting better answers
follow the forum rules, only english allow, salu2

Error: Your request could not be completed because a failure occurred while the report was being processed.

Post Author: sagimann
CA Forum: Deployment
Hello,
I'm not sure if this is due to bad deployment, but I suspect it is, at least due to bad environment.
My env is:
Solaris 10 64 bit
Oracle 10g client installed under /opt/oracle/app/oracle/product/10.2.0/client_1
BOXIR2 + FP2.6 installed under /opt/reporting, running under user 'bouser'. by the way, 'tnsping' works via that user.
Important bouser env:
ORACLE_HOME=/opt/oracle/app/oracle/product/10.2.0/client_1
TNS_ADMIN=$ORACLE_HOME/network/admin
LD_LIBRARY_PATH=$ORACLE_HOME/lib:$ORACLE_HOME/lib32
I reboot the box, then start BO like so:
cd /opt/reporting/bobje
. setup/env.sh
./mysqlstartup.sh
./startservers
./tomcatstartup
Then, I import a BIAR file with some reports, and whenever I try to open any report via infoview, I get a gray error message INSTEAD of the input param form:
Error:
Your request could not be completed because a failure occurred while the report was being processed. Please contact your system administrator.
This does not occur in our BOXIR2 on Windows, which is why I'm guess it's a deployment/env issue. The main obstacle I have is: how do I diagnose this? there's nothing in the bobje/logging folder, nothing in the /var/adm/message file except for the following line:
May 5 15:23:23 testbox1 boe_pagesd[3865]: [ID 253862 user.error] A failure occurred while the Page Server was processing report 'test report' (id=777) for user Administrator
pls advise,
thank you.

The solution is to turn off the printer preference (bottom of Page Setup screen) in the Crystal Report before uploading to the Server. Thanks to: http://pinchii.com/home/2011/12/error-adding-reports-to-crystal-reports-server/
The explanation, from a comment in the above linked blog post:
"To elaborate more on the error, what basically happens is that the Crystal Reports engine tries to get the status of the u201Creport printeru201D aka u201Cdefault printeru201D which was present on the system when the report was created, but the printer does not exist anymore. This causes the Crystal engine to error out. By setting the report to u201CNo Printeru201D, it tells the Crystal Engine not to look for that report printer when opening the report."
Edited by: abirdman on Feb 3, 2012 9:49 PM

Need Cooling Fan For MSI FX5200-T128

Can anyone suggest a cooling fan to fit the MSI FX5200-T128.

Quote
Originally posted by cgrossi
man, for me to overclock my fx5200 t128, i fitted a coolermaster dp5-6j31c that i used on my 1800+.
Thats a pretty big heatsink. Doesnt it put strain on the AGP slot?

FX5200 T128 and DVI Port :(

Dear Friends
I have a MSI GeForce FX5200 T128 (128MB) VGA card.
It has only D-Sub Port(DB 15-Pin) and a S-Video port and DO NOT HAVE A DVI Port :(
But in the manual its written that
"Support for dual-link DVI for compatibility with next-generation flat
panel displays with resolutions greater than 1600x1200 without
the need for reduced blanking"
So, now I'm planning to buy a new LCD/TFT monitor, to take advantage of digital picture through DVI input without converting from Digital->Analog->Digital. SO that I'll not loose any quality.
So Is it possible with my card ?
I think its not possible as it does not ve a DVI port.
Very bad product .................

Thank you all for your support.
But, it has been writen in the FX5200 T128 section/features.
So I thought .......
Anyway seems I ve done a bad investment Any exchange offer from MSI for Asian customers in future

KM2M Combo-L(MS-6738) and FX5200-T128 DDR TV out 8x

?(
I need some help, I need to know if I can install a videocard MSI FX5200-T128 DDR TV out 8x in a motherboard MSI KM2M Combo-L(MS-6738)
Thanks

Aetius,
I do not know, can you? :D
The card will work with the board, but I do not know if you can do it or not.
Richard

FX5200-T128 AGP (Tv-Out)

Hello
Hopefully someone can answer my question since MSI doesnt return my emails or my phone calls. This makes me want to spend my hard earned money buying another MSI product.
I just built myself a new system and cant figure out why I am having the problems with this video card. I am using this video card until I decide which one to upgrade to. A little about my system first.
CPU: AMD XP 3200+
Ram: Cosair (2) 512meg) chips PC3200 (Mastching Pair)
MB: Gigabyte 7nnxp (Latest Bios)
Sound Card: Sound Blaster Live 5.1
HD's: 85, 120, 160 gig Maxtor Drives
MSI FX5200-T128 (Latest Bios)
KDS VS-195 19 inch Monitor
I am running the Latest Bios and software MSI FX 5200 Drivers 53.03 (Nvidia Drivers) for the FX5200-T128 AGP 8X video card and still have these problems.
The problems I am having probably have something to do with the refresh rate but i'm really not sure just guessing. The taskbar (down below) turns a solid color and you can't see the icons on it when dong different tasks on the computer. Evently it goes back to normal and everthing goes back to normal. When I first boot the computer up I get a white background (which doesnt bother me to much). Plus I use Photoshop a lot and when I am first booting that up the screen goes to white but after its loaded up I see everything I need to see. If I am in Photoshop doing some editing the whole screen turns white and usually the only way around it is to press the esc key and sometimes I loose my work and have to start over. If I go to the control panel then select the display icon/settings/advance/troubleshoot/hardware acceleration. If I lower the performance on the card way down then i don't have a problem but why would I do this.
Any help would be greatly appreciated
Michael

IF you had done a search and some research on that card you would see that it's a glorified GF2 440 MX equivelent and is not a high end video card for much else than a normal business workstation...graphic editing wouldn't be my first choice to do with that card...
Now you could have a bad motherboard as well...power supply could be light on it's output to power your components...it could be a lot of different things...
Need to troubleshoot your system with known good parts of the same manufacturer and chipsets...
Good Luck!!
Bonz

FX5200-T128 Screen flash on log in....

Hi there,
Just purchased the MSI FX5200-T128 card and installed with a new installation of XP and supplied drivers. Upon log in with any user the screen flashes twice, then logs in. Also when I go to the display settings and go to the FX5200 tab the screen flashes. Windows update indicated that I needed a new driver signed in July (I think) so I downloaded these. These were 45.23. After installation of these, hitting the display manager toolbar icon causes the screen to flash, as well as retaining the previous flashing problems!
This morning I have downloaded the 45.33 drivers with the same results.
Any ideas why my screen keeps flashing!?
Thanks in advance,
Mark
Athlon XP 2000
Gigabyte GA-7VRXP
1024Mb PC2700
MSI FX5200-T128

I have another problem. I know that support for this card is poor with the current XFree and have downloaded the run file from Nvidia. I have a new HD and started to boot Mandrake 9.0 from CD. It got as far as hitting enter to start the install....then the screen went blank and that was it....
So now I have problems in both Linux and WinXP!!
Any help would be much appreciated,
Mark

Concerning FX5200 T128 with and without fans!

I have seen the MSI FX5200 T128 VGA card in two shapes: one with a heat sink, and another, a bigger one, with a fan or what's called Twin Flow.
Both of them are MSI GeForce FX5200 T128!
What is the difference between them?

One with bigger fan is overclocked and with temp sensor.

VGA FX5200 T128 (8917) driver to support Linux OS

Hello,
Currently I am install red hat 9.0 (Linux) OS in my PC.
But I encountered problem when detect my VGA card driver.
(VGA FX5200 T128 (8917) driver)
Have anyone encountered before, please advise alternative solution.
Thank you in advance.
Regards,
vivaspeed

Quote
Originally posted by some body
See HERE.
vivaspeed Reply:
Hello,
Thank you of your reply,
but I am confuse which one I need to refer?
My processor is Pentium 4 and my VGA card is MSI FX5200-T128.
So which "Graphics Drivers" I need? Linux IA32 or Linux IA64?
And which "nForce Drivers"?
Should I need to upgrade my BIOS before I install the driver?
My motherbroad series is 875P Neo Series.
can please guide how to upgrade by manually (not LiveUpdate).
At tne meantime, I found another VGA driver from "www.viaarena.com/?PageID=296"
but is only provide for "AS IS" type. May I know is "MSI FX5200-T128" as same as "AS IS" type?
Thank you in advance.
regard,
vivaspeed
[email protected]

FX5200-T128 mosfets extremely hot

Hi,
I have a MSI Geforce FX5200-T128 video card. I'm worried with the 2 MOSFETS near the BIOS chip and Svideo-out because it is getting extremely hot. Is this normal?
Thanks.

Mosfets normally get hot.
They are generally designed to handle high heat. I wouldn't worry about them unless your having problems. If they do worry you I would attach some tiny heatsinks to them with thermal epoxy. Radio Shack sells some or any small heatsink will do.

Is the FX5200-T128 video card compatible with an Athlon 64 CPU and a K8N mobo?

I am building a new computer based on the Athlon 64 3000 processor and the mobo MSI K8N Neo-FSR.
I intended to use MSI MS-8907 GeForce FX5200-T128 as the video card.
However I have been told that this video card might not be compatible either with the Athlon 64 processors or with the mobo MSI K8N Neo-FSR.
Is it compatible or not?
If it's not compatible, what is the cheapest MSI video card compatible with the Athlon 64 and the K8N?
Thank you in advance for your help.

If it's there, it means they at least inserted the card, booted, and installed drivers, as far as what they do from that point is anyones guess. You will see the far right column shows 4x or 8x.
I agree, it is minimal info at best and not my idea of what should be included in a test report.
I don't see any reason why that card would not work, the market is saturated with that type of card.

FIFA2003 don't run on FX5200 T128 ???

I have just purchased a FX5200 T-128. I have this runnig on a AMD 2600 with 512 Mb.
But my Fifa 2003 doesn't run. I can reach the introduction movie and the menu, but after setting all the match modes when the game is loading the program is shuted down and leave me to the desk.
Can some one help me with the configurations?????
Chucky

Chucky,
My crystal ball is still in the shop for repairs and without it, I cannot quite make out the hardware in your comp. Please list your Hardware, OS and specs on your Power Supply.
Take Care,
Richard

Complete hard drive failure. Advice?

I was having hard drive issues last month that I thought were resolved, but now I'm pretty sure my internal hard drive in my iBook is totally dead.
My internal hard drive started making really bad grinding noises during start up, so I booted my iBook from an external hard drive to do a Disk Utility>Repair Hard Disk feature but the internal hard drive doesn't even up anymore. And after I boot up from my external, my internal will begin whizzing and making terrible grinding noises. Upon successful boot up from my external I get this message:
The disk you inserted was not readable by this computer.
It gives me three options: Initialize..., Ignore, and Eject.
Is my internal hard drive totally dead? Any advice?

Using Apple Hardware Test:
You can use Apple Hardware Test to help determine if there is a problem with your computer’s hardware.
To use Apple Hardware Test:
1. Disconnect all external devices from your computer except the power adapter.
If you have an Ethernet cable connected, disconnect it.
2. Insert the Mac OS X Install Disc 1 that came with your computer.
3. Restart your computer and hold down the Option key as it starts up. A list of available
startup volumes appears. Click Apple Hardware Test and click the right arrow.
4. When the Apple Hardware Test main screen appears after about 45 seconds, follow the
onscreen instructions.
5. If Apple Hardware Test detects a problem, it displays an error code. Make a note of the
error code before pursuing support options. If Apple Hardware Test does not detect a
hardware failure, the problem may be software related.
For more information about Apple Hardware Test, see the Apple Hardware Test Read
Me file on the Mac OS X Install Disc 1 that came with your computer.
Also, when you run the Hardware Test, make certain you run the "Extended Test"...
that will tell you if your RAM is bad. Considering the failure code "2rom...
that just might be the problem.
And, if you can, run Disk Utility from your system CD or DVD.. Run Disk First Aid
and make sure the drive is OK... (some of these ideas are echoed online.)
(To use the installer disc's version of Disk Utility, start from the disc1 or DVD while
holding down the C key, and the Installer language window appears. Look into the
upper menubar to find Disk Utility among other options; do not run Installer. This
can be used to attempt to 'repair disk' and also the Utility can be used to wipe the
drive in a number of ways, and reformat it, then attempt an all-new install over an
erased hard disk drive. You'd need to have anything on such a HDD backed up
since this would make such data unrecoverable in the conventional sense.)
Sometimes, a failed hard disk drive can have some data recovered if the Mac it
is in can be started up in the 'FireWire Target Disk Mode' and attached by FW
cable to another Mac; and then any data recoverable could be burned to a CD.
Good luck & happy computing!
edited.

Complete Lightroom Import Failure on Upgrade

I have just upgraded from the Lightroom release candidate to the new 3.4.1 (64 bit) version and I find that I cannot use the import function at all without causing a complete program crash.
When clicking on the Import button, or using the menu selection, I immediately receive a "Program Not Responding" message and Lightroom crashes. This happens whether there is a camera plugged into a USB port, or a card into a memory reader, or with nothing connected at all.
I have done the following without success.
System Restore to before 3.4.1 64 bit
Reinstall of 3.4.1
Uninstall and reinstall of Lightroom
Deleted preferences file
Reboots throughout the processes
Windows 7 (64) Home
Import has worked flawlessly from Vers 2 on with 3 camera makes and 2 Phone cameras
I have searched these forums and the KB but I see nothing that appears to match my case.
I would appreciate help or a pointer to an Adobe technical support email address which for some odd reason related to growing frustration I just can't seem to find on the website.
Rick Grant
Calgary

It has taken some 4 hours but I am back in business -- I don't know why.
After posting my problem I did a complete scrub of all Lightroom mentions on my machine using a 64 bit program uninstaller that went after every mention of the program including the registry entries. The only things I left alone were the catalogs.
I then tried the following without success . . .
Installed 3.4.1
Uninstalled again, ran Ccleaner, installed 3.3
Repeated uninstals but this time removed all catalogs
Disabled all malware/virus and most services and processes
Reinstalled boxed 3.2
Upgraded
Frequent reboots throughout and continued removal of Temp/etc files with CCleaner
In each case the simple act of clicking on the Import button would result in a program crash and despite Microsoft's kind offers no suggestions for fixing the problem ever came forth.
Once in a while I would get as far as a list of folders in the Import dialogue but any click on any of them brought about the crash.
During all of this I was also testing by plugging one of my cameras into the USB port that I had always used for Imports.
But, for some reason that I can't remember, I happened to plug a card reader into a completely different port and suddenly the Import function started to work.
I tested with all of my cameras as well as that same reader and card on the original port that I have always used and everything worked fine, and has continued to work fine since through a final upgrade back up to 3.4.1 and the reinstallation of my original main file catalogue.
I have no idea why things have started working again nor do I know how to avoid the problem in future.
Rick Grant
Calgary

Complete FX5200-T128 failure?

Similar Messages

Maybe you are looking for