Complete shut down
Phone completely shut down after the screen froze and haven't been able to power it back on. Any help?
Try powering it up while the A/C adapter is hooked up to it.. let it charge for a while if the battery shows 0%..
Similar Messages
-
My internet was down for over 24hrs after a storm. During that time, my IPad completely shut down and I can't get it going again. I studied the manual but couldn't find a similar topic. I reset it and now it is totally goofed up.
Does anyone have any ideas or should I just take it to an Apple store and pay?? Any solutions you may have, PLEASE use simple words as I am not a pro, by any means....probably why I'm in this situation.
Thank you in advance.Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
VI file cannot be completely shut down!?
Hallo all experts,
My VI application is to communicate with an A/D converter. It only works properly one time after opening. I have to totally close LabVIEW, then start it again for a second run. When I run HyperTerminal after stop the application, windows says that another program is using the COM terminal. It seems that my VI application cannot be completely shut down, but Why? Is it normal? There is a producer-consumer structure inside my code, perhaps it is due to the bad synchronization of terminating them. Have you ever experienced such situation?
Any tips are highly appreciated.
win2I agree with Centerbolt that the best course of action is to manually close your VISA session in your LabVIEW VI before the VI shuts down. Another thing you can do is to set an Environment option in LabVIEW under Tools >> Options. You'll see a checkbox there called Automatically Close VISA Sessions that shuts down VISA sessions whenever the VI goes idle that was using it. Both these methods should save you from having to restart LabVIEW everytime.
Jarrod S.
National Instruments -
My iPad 2 won't charge and it's completely shut down. I've tried pressing the two buttons simultaneously, but nothing works. It's driving me crazy! Any offers of suggestions would be greatly appreciated. Thanks!
1. The most efficient way to charge an iPad is with the charger that came with the iPad and having that plugged into a wall outlet. Trying to charge while connected to a laptop often doesn't work because the USB port may not provide enough power.
2. Once an iPad battery has completely drained it may take an hour or more on the wall charger before the iPad responds. So after an hour on the charger reset the iPad. Press and hold both the Home button and the Sleep/Wake button continuously until the Apple logo appears. Then release the button and let the device restart. You will not lose data doing this. It's like a computer reboot.
3. If the iPad still does not start up make an appt at the Apple store. It will be far better if you have an appointment rather than just walking in because those with appointments will be taken care of before you are. -
Computer completely shuts down
For the past two days I have been working in illustrator and with about an hour or so left on my battery my computer completely shuts down. I have now lost 2 days worth of work. Extremely frustrated!
Run Apple Hardware Test on your MacBook Pro. Also run disk utility to repair your hard drive and permissions.
Battery information. -
Firefox Can not be completely shut down, Have to use Windows Task Manager to shut it down, I am using Vista, How to fix it????
See this: <br />
https://support.mozilla.com/en-US/kb/Firefox+hangs#Hang_at_exit -
PLZ help my ipod my ipod touch is completely shut down and it doesnt even show the battery icon plz help!
Please don't use a bolded font. It's annoying.
What happened immediately prior to the screen shutting down? -
10.4.10 completely shuts down in the middle of an app
Hi
Since downloading the new update 10.4.10 for my Macbook Pro Core Duo
i have several uncharateristic complete shut downs in differnet applications.
One in Preview, one while typing and email in Mail and one in Safari.
I have had no Printing issues, no airport issues.
I have not a clue how to rectify this issue, but what I am reading in the discussions this update seems to be floored on a few accounts.
Any pearls of wisdom from anybody.Hi Stanley,
sorry for the tardy reply I have had a few busy few months with not a lot of internet access.
I am getting errors. I had a look at the crash report via the console manager. It does not look good, but i am not sure what i am looking at.
I also don't know how to check the disk space my boot disk has. I can see the volume via the sys pref but don't know where to look for available space or how much is left. Please advise.
how does this effect the automatic shutdown.
my computer is also not letting me shutdown at all. it goes throught the motions of exiting but it gets to the point where I am just getting a blue screen and a radial symbol rotating rapidly. From here it will continue to do this for a long time. and not stop unless i remove the battery and electrical power supply.
what do you think or what do I do from here?
Much appreciated.
Host Name: Mac-Duo
Date/Time: 2007-09-04 19:02:11.914 -0400
OS Version: 10.4.10 (Build 8R2218)
Report Version: 4
Command: Exited process
Path: Exited process
Parent: kernel_task [0]
Version: ??? (???)
PID: 1735
Thread: Unknown
Exception: EXCBADACCESS (0x0001)
Codes: KERNPROTECTIONFAILURE (0x0002) at 0x00000014
(null)
Unknown thread crashed with X86 Thread State (32-bit):
eax: 0x00000000 ebx: 0x900241e4 ecx: 0x00000000 edx: 0xb011ef18
edi: 0x00000000 esi: 0x14b85300 ebp: 0xb011ee58 esp: 0xb011ee58
ss: 0x0000001f efl: 0x00010286 eip: 0x0031599f cs: 0x00000017
ds: 0x0000001f es: 0x0000001f fs: 0x00000000 gs: 0x00000037
Binary Images Description:
Thanks
Darryl -
I don't think my Mac Pro is completely shutting down. When I hit the power button, it just turns off immediately instead of going through the normal shut down procedures. I heard that I should try resetting the SMC, which involves removing the power cord. However, when I remove and replace the power cord, it turns on automatically, so I can't even properly reset that to see if it is the issue. Is this probably a power supply issue?
Actually, in case this information helps... The computer went into sleep mode the other day, and would not come back. This is a work computer that I use for our photography business, and at this point I am just trying to run it as a drive to get the photos onto our new computer, but this issue is keeping us from doing so. Any help would be greatly appreciated!Try a SMC reset.
DALE -
Why has my iBook started to completely shuts down when power runs out?
I purchased my iBook G4 in early 2006 (OSX 10.4.11)
Until last week, I would regularly use my laptop until the battery charge was used up. I would get a low charge warning and it would automatically sleep. I could then plug it in to charge. When it was plugged in, I could touch the track pad or power button and all of the programs that were open when the power ran out would be there, just as I left them.
This has recently changed. Now when the power runs out, I receive the same low charge message, but instead of sleeping, my computer completely shuts down. When I press the power button to reboot, everything starts back up fine, but I get a message that my date and time are off and need to be reset. I then go to the Date and Time menu, which automatically updates through my wireless connection.
My questions are:
1. Why is it shutting down instead of sleeping?
2. Why is my date and time reseting to an incorrect date and time?The difference is that in the past, your battery shut the computer down when their was enough juice to safely sleep the machine. Now it thinks it has enough juice, but it's truly running out. The battery is necessary to maintain the date and time in the computer.
Your battery needs to be calibrated. You should follow the instructions at:
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh1959.html
This will allow the battery to truly know how much juice it has left. -
Easy way to fix this download problem. Tech person nice but referrals to links WAY too complicated. I just want to easily load program I paid for.
My downloads are incomplete, in some cases only 30 seconds per episode. completely shut down computer and programs to try to remedy.
Is there a real human to talk to at Itunes who won't say your warrenty is over so I can't help you?? THXEasy way to fix this download problem. Tech person nice but referrals to links WAY too complicated. I just want to easily load program I paid for.
My downloads are incomplete, in some cases only 30 seconds per episode. completely shut down computer and programs to try to remedy.
Is there a real human to talk to at Itunes who won't say your warrenty is over so I can't help you?? THX -
My iphone5s completely shut down, says no service
my iphone completely shut down, says no service
Hi danmcl20,
Thanks for the question. Based on what you stated, it seems like you have no service in the status bar. I would recommend that you read this article, it may be able to help you isolate or resolve the issue.
If you see No Service in the status bar of your iPhone or iPad - Apple Support
Thanks for using Apple Support Communities.
Cheers,
Mario -
My iPhone 4 registered 60% battery and two minutes later completely shut down
My iPhone 4 registered 60% battery and two minutes later completely shut down, next day it said it had zero battery and turns back on after plugging in for a few minutes... what's going on? I was using the maps application in the minutes before it shut down on me.
Maybe it's just the battery percentage display that is messed up? Have you done the recommended monthly or so drain the iPhone down to the point it shuts down and then charge to 100%, to recalibrate the readout?
-
Hi, I was updating my apple software and my ipod touch completely shut down. I got an error message that my ipod touch could not be restored. what the ????
please help. it wont start at all, no power. itunes doesn't even recognize it anymore.First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes." -
I am having trouble with my cursor freezing between applications after installing Mavericks. Called Apple on my 3 year warranty and opened a case. They suggested a complete shut down of computer and turning off mouse. Then a reboot and turn on mouse. So far iit has seemed to work. Hope this continues??
Hope it helps others.I think you can solve your problems by removing your AppleID email address from BOTH the Messages setting on your iPhone and the iMessages settings on your Mac.
On iPhone:
Settings > Messages > iMessage > Dissabled
Settings > Messages > Send & Receive > touch the "(i)" < touch "Remove This Email"
On Mac:
Open "Messages" application
Click "Messages menu > Preferences
Click "Accounts"
Select your AppleID account
Under the "You can be reached for messages at" settings, uncheck your AppleID email address and your phone number
Then uncheck the "Enable this account" setting
And lastly, ask all of your friends with iPhones to delete all iMessage conversations (blue bubbles) in their entirety.
To test, send a friend a new text using their phone number (not their email address) and watch the color of the bubble. If it's green then you are using SMS.
Maybe you are looking for
-
In 4.1 BO Client Tools not able to find data source for BVM
Hi All, In 4.1 BO Client Tools not able to find data source for BVM Its creating issue . So if any body have any solution please let me know. Regards, Abhishek
-
How do I delete all "songs that can not be located" at one time?
In trying to move my music files around from drive to drive in my computer, I messed up somehow (I don't know what I'm doing, exactly and am just making things up as I go along)....but long story short, I now have duplicates of most of the songs in m
-
Adapter file receiver command line dynamic
Hi everybody, In the adapter file receiver, I'd like to put the command line dynamically depending of informations of the payload of the message. Do you have ideas ? Thank you in advance for your collaboration. Regards
-
Connect to ServerSocket of codebase host fails thru proxy since 1.6.0_03
hi there, I have an applet that connects to a server-socket of it's code-base host (i.e. the server it has been loaded from) and loads additional data. since 1.6.0_03 the connection fails with a SecurityException when there is a proxy server in betwe
-
Reader XI % inetrnet preferences
hello i had installed reader XI but i cant see in preferences-internet-display - protect in safe mode.is no longer available??