Compression settings for 4 hour video

I am trying to compress a 4 hour and 23 minute video but i can not find the settings to do this. The largest allowed time I have been able to achieve is 174 minutes. What settings should I use to make this DVD?
Thanks for the help.

There are no settings for a 4 and a half hour video in Compressor. You will have to create one by drastically lowering the bitrate. Be aware that you will need to burn to a Dual Layer DVD. DVD-R's will typically only hold 2 hours of decently encoded video. Even with a Dual Layer DVD the bitrate (espically using Compressor) might be too low to get decent quality and still fit.

Similar Messages

With Premiere elements 11, when Publish/Share (saving) a finished video, selecting H.264 .mov file type, what are the recommended Codec and Aspect settings for a crisp video and a small file size?

With Premiere Elements 11, when Publish/Share (saving) a finished video, selecting H.264 .mov file type, what are the recommended Aspect and Codec settings , for a crisp video with a small file size?

Gary Krouse
We will customize a very detailed reply, but
(a) What are the properties of your source media?
(b) What did you or the program set as the project preset to match the properties of the source media?
(c) What specific requirements do you have for this H.264.mov export file?
File size can be a compromise between bitrate, file size, and quality.
Thanks.
ATR

Best settings for Green Screen Video with Canon Mark iii

HI
What are the ideal camera settings for Green screen video.
Iso?
aperature?
Depth of field settings (best to have the green screen a bit out of focus?)
Any other camera settings would be helpful.
Thanks
Rowby

Hi Rowby!
Thanks so much for writing in about green screen shooting with the EOS 5D Mark III camera. Green screen shooting can come down to some crucial elements and how well you handle the camera and the lighting.
Arguably the most important thing is to have excellent lighting on the screen. Without this, the keys used to replace the green screen will not be accurate. So hopefully you have a good set of lights you will be using to actually light the physical screen.
With regards to ISO, shoot as low as possible. We suggest that you stick in the ISO 200-400 range where possible. With good, high key, proper lighting on the screen this shouldn't be an issue.
Aperture should actually be in the higher end of the range, you would want to stick to apertures around f/8 and above. Again, with adequate lighting this shouldn't be out of reach. This is so the green screen is more in focus, versus having it out of focus, which would not yield successful results.
Use an appropriate lens to the subject, for example if you are doing wide shots- use only the focal length needed for the shoot and no wider. For head shots, close ups- use a lens that will get you close.
Following these suggestions should give you some pretty good results. Remember, if this is your first attempt don't be discouraged, green screen shooting can be difficult to accomplish.
We wish you the best of luck in your endeavor!
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Trying to figure out compression settings for existing video to re-use

So, I had a 3 minute video that, at settings according to the "info" panel" for it is at 720x480, .264 compression setting, and small or big looks great-- I got the file to under 20 megs.
Now, after messing with NTSC settings and whatnot, I tried bringing it back to the original settings with a recut version of the same length, no extra bells and whistles in the video, and yet, I can't get it under 250 megs.
Is there a way to find out the specific settings for it beyond the simple file info window?
Also-- does key frames at a low setting (24-30) affect it greatly?
I just need to get it back to that little size without sacrificing sound or quality-- I did it once, i need to do it again.

...anyone?

What are the best export settings for a HD video in Premier Pro CS4?

Hi!
   I've been having so much trouble with this issue and it's something that continually frustrates my boss. I have a HD video the settings for it are
FPS 23.98
1920 x 1080, then a few lines down it says 1408 x 792
16 bit,
2 channels
48000 Hz
   What should the settings be when I make a new sequence?
             When I look at it in the window in Premiere Pro I have to contantly 'shrink' the image to fit the window, is that something I should be doing or does it indicate the sequence settings are incorrect?
But more importantly what should the export settings be? I exported a 4 minute long video and the size was 1 GB, I know that's too big.
I need to export it without loosing any quality and export another one that meets the Youtube and Vimeo limits on size.
Vimeo is 500 MB per week, sometimes I upload 4 videos per week. I think Youtube you can only upload 500 MB at a time.
I need to get smaller sizes with loosing the least amount of quality possible AND the best export settings for quality, so I guess I have 3 separate questions-
What are the best sequence settings for HD video?
What are the best export settings for HD without loosing any quality?
What are the best export settings for the size to come out around 500 MB with loosing the least amount of quality possible?
Thank You!
http://forums.adobe.com/thread/713070
On the above thread I used the 5th anwer, and it's going to take about 7 hours to export a 4 minute video :/

It Stands for "Coder Decoder."
Your format is like a container for your video file. Certain containers can hold certain codecs and not others. Other containers can hold other codecs. Sometimes different containers can hold the same codecs.
This might be a bad analogy but I'll give it a try.
A coffe cup (container) can hold pretty much any liquid you drink, where a red solo cup (container) won't hold scolding water. So, the coffe cup would be your container of choice most likely because it has the most options for liquids (codecs). But, you might want a red solo cup for just a single crappy beer at a party (a moderate quality streaming video on the web). In that case, you don't need all the optoins of another container.
In Premiere Pro CC H.264 is a Container and the Codec in one option. This has been streamlined for web distrobution of video to be played in browsers without things like Flash or special players.
Were as if you choose the QuickTime Container there are over 40 codec optoins (at least on my machine with additinal ones installed) but you may run into an issue where your browser doesn't support QuickTime playback.
I would say that your container is for compatability with players and your codec is taken into consideration when looking at the quality of the compression.
Yesteraday I wrote a blog entery on Exporting from Premiere Pro and found that the MPEG-4 codec inside of the QuickTime container gave me much richer colors than the H.264 container/codec option.
I posted the link before but here it is:
http://goo.gl/8GZq4i

Best settings for Low-Res Video for email or download?

I have a 15 min video shot originally in HD. Just need a low def file that is universally playable on mac or PC. What are the best export settings for this? Need a file less than 100MB.
Also seems like everything is taking 1-2 hours to export! Why so long?!?!?

15min video down to <100MB?..
=> you will not see a thing in such a compressed 'video'.. no way.
consider splitting your project in two, use YouTube, mail YT-Url ..
YT is compatible for most OS, PC or Mac or Linux or ...

Best Streamclip settings for iPhone 4 Video - to edit in FCE

First, the problem: iPhone 4 records HD video in h.264. But Final Cut Express doesn't have sequence settings for editing h.264 or iPhone video clips.
The solution: I'm using Streamclip to convert all of my iPhone 4 videos to a format FCE lets me edit in.
Question: What are the optimal settings to insure that my final output retains quality almost equal to the original video shot on my iPhone? (More specifically, I plan on uploading to Youtube as a HD video).
I've read somewhere that I should convert to Quicktime Movie format, with Apple Intermediate Codec 720p 30fps. Is that the best compression type to convert to for editing iPhone 4 videos in FCE? If so, how should the other settings in streamclip be jiggered? For instance, does it make much difference if I set the Quality slider to 100% (As opposed to the default at 50%?) What about audio compression settings?
(P.S. I think it's very annoying that I can't directly edit a video from iPhone 4 on another consumer Apple product, the FCE. Does FCP let me directly edit h.264/iphone 4 videos?)

The slider makes no difference as AIC is variable bit rate within a specific range. No audio compression in FCE ever. Uncompressed stereo 48k, the video standard sample rate.
It would be truly miraculous if FCE worked with iPhone media as the current version predates it by three years, which in computer lifetimes is two generations, basically the equivalent of your grandfather having developed an app for a smartphone when he was a young man. FCP is a mere year old, well before the iPhone did video. Furthermore, if you'd read the forums, you'd see that H.264 is an acquisition and delivery forward. It is not used in production. The codec is not suitable for efficient production and really should never be used there. It's very unfortunate that camera manufacturers have taken the cheap way out and used this codec, rather than actually developing and using a suitable intraframe production codec.

Best settings for exporting crisp video/graphic from iMovie to YouTube?

Hi, I am working on a video for a client and after viewing on YouTube they had some issues with the type not looking "crisp," and I'm not sure how to fix it, not sure if it's a YouTube thing or something I am doing wrong.
I am working in iMovie 6/HD on OS 10.4.11. I do my "type slides" in Photoshop and import them into the iMovie as photos (JPGs). I know some text/titles can be done in iMovie but there is very little control I have over what goes where, so by making my type slides in Photoshop I have more creative control to do what I want. I have done tests and it doesn't seem to matter what resolution the Photoshop files are when they're imported, the results are always the same.
If anyone has a better suggestion for doing the type slides I'd gladly welcome them, but I think what I really need to know is the following:
What are the best expert settings to export my iMovie file as, so that when I upload to YouTube, the quality stays fairly crisp? Or does YouTube's compression just negate anything I can do on my end?
I have googled and found settings recs on other sites and other boards and tried a bunch of them and my results aren't any better than my original effort.
From another post on this board I discovered I could play with the Filters setting when exporting, and I have set that to Sharpen and also used the Brightness filter to lighten the video (it was a little dark). I uploaded to YouTube and I think it is a little better, but would still love the info if anyone has a guaranteed rec for correct settings for YouTube video from iMovie HD/6.

Hello Brian,
Have you tried de-interlacing before exporting?
Sometimes, when I'm in a rush, I would expand the Canvas/Viewer (viewed at 100%), pick the clearest frame, and do a screen capture.
For example, with the captured image (in Photoshop), I have a marquee preset at 640x480 (NTSC). I created an action to crop, resize to 720x480, then set the Pixel Aspect Ratio to NTSC.
Gary

Compression settings for H.264

Can anyone recommend some settings for making making H.264 video intended for delivery on the web at 640x380?
Thanks.

Heya Rick,
So I was looking at the H.264 settings in Compressor and it would seem as though the highest bitrate is 1500 kps so guess you can't do bit rate between 2000 and 2500 k/bits like another poster recommended by using Compressor for Apple Devices settings. Also there isn't much control over the audio of the h.264 file in Compressor whereas QT conversion from FCP allows you to select a mono audio file with a lower khz rate and render quality.
The difference between selecting stereo vs. mono will be the difference between 1/2 or twice the filesize for your audio file which will absolutely affect your total filesize but make little to no difference in your viewed file intended for web viewing. Take a look at a standalone Stereo track AAC 44.100 kHz 192 kbps that is 5 mins long and you're looking at about 5 MB file just for the audio!!! Cut that to mono and drop the frequency and bitrate and that 5 mb audio file will be about 1MB.
I have always used QT conversion from FCP and have only just now had the opportunity to look at the h.264 settings in Compressor and judging from initial impressions I would go with QT conversion from FCP.
For the video you mention I would just go with export using QT conversion from FCP. For video settings use automatic keyframes with an automatic datarate with quality set to Medium. Best quality multi-pass encode. For sound settings use Linear PCM Mono channel 32 khz rate and Faster Quality render setting. That should give you a nice, small file size that will look and sound good enough for sit down interview video between 3-5 mins. in length.
Also remember that the h.264 can be used with a Flash player instead of QT player so those without Quicktime can view the file without having to install the QT player. You can use something like the JW Player from http://LongTailvideo.com or simply change the extension of the compressed h.264 to .flv and use it with any Flash Player above 9.0
hth

Compression settings for G3 playback

Greetings, I'm using EyeTV export to convert recorded clips to QT movies. Although I'm working on a G4, the QT movies will be played on a G3 iMac. I have discoverd altready that the default compression settings create a movie that the G3 can't handle (it jumps frame by frame). It is suggested that I try other compression settings. I would like to, but I don't know anything about this subject.
For reference, The default settings for export to QT movie:
type MPEG 4 video (there are a lot of other options)
frame rate 29.97 fps
compressor quality high (on a slider from least to best)
data rate automatic (it can be restricted to some kbits/sec instead)
Please can someone suggest which settings I might change and in which direction to achieve G3 playback. Video quality does not need to be great, I accept that there is a tradeoff.

Thanks. After some experimenting, I found that export as Quicktime movie as H 263 seems to play on the G3 with good video quality.

Camera settings for making youtube videos

I have a Canon 60D and CS4 master collection with Premiere Pro and Encore. What settings should I shoot video at in order to get the best youtube output? My choices are 1920x1080-30; 1920x1080-24; 1280x720-60; 640x480-60; crop-640-60

Thanks Bill, that's a most honest answer. I also found this tv segment to help in the camera settings. http://tv.adobe.com/watch/shooting-and-editing-hdslr-video-using-adobe-tools/-setting-up-t he-camera-correctly-for-dslr-video/ This is most exciting challenge and a healthy switch from my traditional photo skills.
Bob.

FCE export settings for higher quality video

Hello. I'm a self-schooled newspaper video features producer and relative newcomer to Final Cut Express, shifting from Premium Elements. I've just begun using it to upload videos to my newspaper's finicky web system, which will only accept .flv files of a certain size. My modus operandi has been to export my videos as large .avi files, using Quicktime conversion and DV/DVCPRO/NTSC, with medium quality, with 16 bit sound set at 32 Khz. Then I run that .avi through the Adobe Flash Media Encoder with a frame rate of 15 fps, deinterlacing and resizing the screen to 640 by 480. This procedure (outlined by our former video editor) produces serviceable web quality video (You can see video that results from using these settings at http://wvgazette.com/multimedia). So, two questions: 1) I have created an 8-minute FCE music video for my band and wish to export it at a higher quality (for use on Vimeo) than these newspaper settings. Which of them do I change so that a higher quality video results without waiting all night for a massive file to upload? 2) And wthere might I turn for guidance on better understanding the Sanskrit of FCE video export settings for newbies? Thanks for any help.
Douglas Eye
http://hundredmountain.com

The simplest way to produce good quality video for the internet is:-
1. File>Export Using QT Conversion.
2. The "Format" window should say, "QT Movie".
3. In "Use" select "LAN/Intranet" from the dropdown menu.
4. Click "Save" and when it has finished encoding, upload it.
Do not mess about altering audio settings, frame rates etc.
Using the above settings an 8 minute video would be encoded in around 20 minutes (depending on computer speed) and would be well under 100MB.
Is that too big?
Message was edited by: Ian R. Brown

Best Compression Settings for Internet - jagged lines

Hi all,
interested in seeing what people think the best compression settings are from FCE HD to Quicktime. I have a 2 minute video to compress which needs to go on the web. Attempts so far have resulted in jagged edges/lines on any footage which is moving. Locked off shots look great though. I'm trying to keep file size to under 10MB which shouldn't be a problem.
Any help or advice will be greatly appreciated.
Thanks in advance
Peter T

Hi(Bonjour)!
See this link:
http://www.kenstone.net/fcphomepage/qt_movies_fromfcp.html
Michel Boissonneault

...best compression settings for a 12minute dvd

...other than 90 minute preset... and would it yield a better video? And what are the best settings for large screen television? The video is standard definition but anamorphic 720x480. Thanks

You can raise the average bit rate to 6.8 and max bit rate to 8. I use this setting a lot. Below is the bit budget worksheet I use. Though it tops out at 7.8 for max bit rate, it's ok to go to 8 in Compressor.
http://www.kenstone.net/fcphomepage/bitbudget.html
As far as the large screen question, I believe you are stuck at 720 x 480 because that is what standard def allows.

Best volume/compression settings for AUDIO for Rock concert DVD ???

I am putting the finishing touches to a 2 hour rock concert DVD.....
I am converting the wav/and 5.1 to Dolby 5.1 and 2.0 files ....
They are sounding really quiet compared to the original waves...???
I can see that there are some dolalogue/audio compression settings and something set to -21db.....
How can I make them louder...and if I do will it mess up playing on normal DVD's ....
I know there are some DOLBY compresor settings in mac DVD player that make the sound pump if switched on...
Any thoughts or help would be appreciated???

Hi
You must change some settings in the standard Dolby presets to keep the original level and mix:
- Dialog Normalization: -31
- Compression preset: none
This way your AC3 files will keep the level and mix from your original files.
Hope that helps !
Alberto

Compression settings for 4 hour video

Similar Messages

Maybe you are looking for