Computer can not read airport admin utility.

I am on the web, but I need to change my password so my PC can also connect via the airport. Although, when I try to change the settings of the airport I am either told the airport is not connected, or it will tell me that there was an error in communicating with the airport. What gives?

I did read your posts - but I'm not certain you followed the instructions (from the beginning) provided in link to the article "Starting from scratch". The advice provided in the link "Starting from scratch" begins by having you do a hard reset of the Airport Base Station before trying to run the Airport Admin Utility again. Sometimes doing this will finally allow the Airport Admin Utility to see and access the configuration of a Base Station when all other attempts to get the Airport Admin Utility to access the Base Station have failed. Any yes - I have indeed seen your problem posted many times over the past few years within the thousands of postings I have read in the Airport discussion forums on this web site.
If you did follow the instructions to hard reset the Base Station, and the Airport Admin Utility still fails to be able to access the Base Station then my apologies, and I'll have to admit I won't be of any help.

Similar Messages

Can't open AirPort Admin Utility configuration file

I'm using an AirPort Extreme Base Station connected to a cable modem through the WAN port and to my G4 Cube running OSX 10.2.8 through the LAN port. I also use an iBook and eMac with AirPort cards to wirelessly access my network. My problem is that I can not open the configuration file so that I can change my settings. I get an error message that AirPort Admin Utility can't read the configuration file of the base station. I tried resetting the base station to the factory settings, to no avail. So now I also can't set a password and encryption. Any help would be greatly appreciated!

To clarify--I previously had a password protected network set up and working. I wanted to change the settings and couldn't open the config file. I reset to factory settings successfully, but still can't open the config file, which I need to do in order to encrypt and set a new password. Thanks!

How can I get AirPort Admin Utility for Graphite and Snow 4.2.5 to work with OS10.6?

I've upgraded to the latest version of Mac OS and now AirPort Admin Utility for Graphite and Snow 4.2.5 won't run. Any suggestions on how to either run this utility or otherwise get access to my old Snow Dual Airport via another method? Airport Utility doesn't see the device, despite repeated scans. My computer and iPad connect no problem to the device, but both iPod and iPhone won't take and hold an IP address. (If any one can help me solve this issue, I can live without access the Airport.)
Thanks,

I've upgraded to the latest version of Mac OS and now AirPort Admin Utility for Graphite and Snow 4.2.5 won't run. Any suggestions on how to either run this utility or otherwise get access to my old Snow Dual Airport via another method?
Unfortunately, you will need another Mac running a much earlier version of OS X to be able to install AirPort Admin Utility and make any settings chances to the router.
Since the normal life of a wireless router is around 5-6 years of use, now might be the time to consider a new router that will provide far better performance than the older Graphite/Snow AirPort.

How can I get Airport Admin Utility to Locate My Extreme Base Station?

In an effort to repair some network connection problems I was having with my ISP (or so I thought), I reset my Airport Extreme Base station today. I have been unable to get it back to normal since. I'm currently connected to my ISP through an Ethernet connection directly from my modum to my iBookG4. Now, when I try to re-established the old network connections with my Airport Extreme, I cannt get the system to recognize a base station. When I use the Airport Admin Utility, the window pops up and *** me to select a base station, but there are none in the window. When I rescan, nothing comes up. The airport setuup utility has been no help either. Any ideas how to get my base station back? Thanks!

Hi, Tesserax:
Thanks so much for your reply. I tried the direct connection, as suggested in a previous message I saw on this board. Didn't work for some reason. Lucky for me, one of my neighbors works in the tech department of a nearby Apple Store. Last night he was able to get the base station working again. I wish I could share how he did it on this message board, but it was beyond my modest understanding. Again, thanks for taking the time to reply!
Best, Kevin

Can't get Airport Admin Utility to see network

Configuration:
IBM Thinkpad A 31p
Windows 2000 SP 4
Linksys Wireless G PCMCIA card
Airport Express
I am currently connected to the internet via the Airport Express but thee Admin Utility can't see the Apple Network no matter what I do so I can't enable security - anyone have any suggestions.
Correction: I have just fixed the problem by using a second boot drive with no firewall

Do a soft reset and enter a new password.
Resetting AirPort Express
http://docs.info.apple.com/article.html?artnum=108044
iFelix

Airport admin utility dead...

I'm trying to set up my airport extreme ('05) and have found that the airport admin utility won't open. I've tried getting info and unlocking it, marking it as read and writeable, but no go. It shows up in my utilities as an app, with a size and date but fails to open. I can't find a place to download the app...

Are you using the round AirPort Extreme base station (AEBS) or the new 802.11n square AEBS? If you are using the new 801.22n square AEBS, you need to use the "AirPort Utility" NOT the "AirPort Admin Utility".

Airport Admin Utility, iTunes, Airfoil can't see AE base station

I know this is not a new topic, but I can't find an answer in any of the other threads. With other users the problem seemed to "magically" go away. I have not been so lucky yet.
Airport Admin Utility can't see my AE base station but I can find it using "other" and typing in the IP address. I was able to update the firmware to 6.3 (again using "other" and typing in the IP address since the fw updater couldn't see it either). I can see it (with it's name displayed) with my router software. However, it does not show up in iTunes or Airfoil either.
The base station is connected via ethernet to my home network. I tried rebooting the computer, restarting the base station, I also tried a hard reset on the base. I do not have "distribute ip address" checked. I do have "enable Airtunes" checked. The firmware on my Linksys router is up-to-date and not a hack. I'm running OS X v10.4.5 on a Dual 1.42 GHz PowerMac G4.
Thanks in advance.
Dual 1.42 GHz PPC G4, 1.42GHz Mac Mini Mac OS X (10.4.5)

okay, I connected the AE base directly to the PowerMac with the ethernet cable and it showed up in everything (Airport Admin Utility and iTunes). So I guess my problem is with the router. What do I do now? This router is only a couple of months old.
When you suggested I disable DHCP, did you mean in the AE settings or on my router? As I mentioned initially, I do not have "distribute ip addresses" set up on the AE base. After reconnecting the AE base to the router, I tried disabling DHCP on the router and that didn't fix the problem.

Airport Express not Appearing in iTunes/Airport Admin Utility

After upgrading to iTunes 7, Airtunes did not work, so I followed the tips on the forum discussions, on MacOSXHints.com (resetting the IPv6 preference) and so on.
However, now iTunes will not recognise the base station at all. I think this is connected to the fact that the base station will also not appear on the Airport Admin Utility list. BUT... I am able to access the Airport Express by entering its IP address and password via the "Other" button. This has allowed me to check the AEx configuration settings, reset the hardware, re-upload the firmware, and even re-configure the AEx from scratch.
I am able to use the Internet through the AEx, and the network appears in my airport menu bar list, so I can select it and other wireless networks in range... It seems that iTunes and Airport Admin Utility just cannot see it. I have tried every combination of 'soft reset', 'hard reset' of the Aex, trashing of various airport admin utility and itunes preferences, and restarting software and the whole computer but this problem still persists.
Any ideas?? iTunes 7 is great, but I want my Airtunes back!!
Thanks in advance - Danny
iMac G5 20-inch Mac OS X (10.4.7)

you may be suffering from wireless interference.
download iStumbler and note the channels other networks in the vicinity are broadcasting on, then change the channel your network is using as far away as possible from those.

Airport Admin Utility can't find Airport Extreme

I have an older Airport Extreme, about 4 years old. It's been giving me trouble lately, where basically I check my computer and it's not online. I have to click the tiny reset button on the back of the airport and that usually works fine (although annoying).
Today the problem seems a bit worse. I tried the reset thing, but that didn't work. So I tried to do a reset through the airport admin utility. Unfortunately the utility can't seem to detect the airport, although it does detect the airport express we have downstairs (which is essentially used to extend our network a little further).
Currently, of the three tiny lights at the front of the airport, only the middle one is lit, and it is not flashing. Earlier, just after doing a restart, the middle light was blinking slowly and the third light (the one on the far right) was blinking more rapidly. I have not seen the first light lit up today.
If anyone has a suggestion on how I might get this working I would very much appreciate it. Thanks.

Are you getting internet access through the airport? I have the same problem - airport admin utility can't see the airport, but the airport extreme has created a generic network that i can't manipulate without airport admin utility. I have internet...

My Airport Base Station does not appear in the Airport Admin Utility

I cannot see my airport extreme base station in the Airport Admin Utility nor in Airport Setup Assistant via Airport. It worked yesterday but when I was trying to set up a network something must have changed but I don't know what it is. (The setup didn't work so I am only using one base station right now.) The only way I can configure/reconfigure the base station is by physically connecting via an ethernet cable. Then no problem. I have two computers and neither can access the base station with Airport Admin Utility via Airport. I have installed the latest Airport Update but nothing has changed. What happened?

You should be able to use the second Airport Extreme
Base Station as a wireless print server. What I
suggest you do is:
1. run the Airport Admin Utility and clean up
settings on your existing Base Station:
- under the Airport tab, make sure you have not
selected to "create a closed network"
- under the Access Control tab, clear out all
settings
- under the WDS tab, clear out all settings
- under the Network tab, make sure the box is checked
to "Distribute IP addresses" and "Share a single IP
address using DHCP and NAT".
- update settings to the Base Station if you changed
anything.
2. do a hard reset of your second base station per:
http://docs.info.apple.com/article.html?artnum=107451
3. for now, put both base stations and the Mac in the
same room. Run the Airport Setup Assistant, and use
its guidance to configure the second base station as
a new base station that "extends" the wireless
network of your main base station.
That should do it.
Thanks very much. The printer works great from both computers via my second airport base station. And I can see both my base stations in the Airport Admin Utility.

AirPort Extreme Base Station is not Available in AirPort Admin Utility

I don't see my APEX Base Station in the list in AirPort Admin Util. I can configure by opening by IP. I have no software firewall. I have plugged in directly to base station, and have reflash with 5.7 firmware. I am using 4.2 of AirPort Admin. I've Tried everything I can find in forums. Anyone else have issues?
I'm using Mac OS 10.4.4

I have tried resetting it. It doesn't always work. Sometimes the base station is listed, and sometimes it is not. The base station is functioning though. I can access the newtork, It just doesn't show up in Admin Util.
I also have an AP Epress connected to AP Extreme via WDS. From the wired side, they either both show up or both do not, which is expected. When they don't show up on the Admin list, the Express also doesn't show up in iTunes from the wired side. Wireless clients don't seem to exhibit this problem.

Airport Extreme working but not visible in Airport Admin Utility

Recently my Airport Extreme (spaceship version) stopped showing up in the Airport Admin Utility v4.2.
The internet works fine computers can connect wirelessly or wired to the Airport Extreme and use the internet. AppleTV isn't visible in iTunes anymore either so it can't sync but can connect to the internet to see previews, YouTube, etc.
I have tried removing Airport Admin Utility and reinstalling, checked permissions, all okay.
Any ideas?

Ah - more clues always help!
In that case, I tend to agree with your assessment. For some reason, the Bonjour automatic network device discovery process seems not to be working properly on this Mac. I'm not going to be of much help in troubleshooting that problem.
The only other issue I have encountered is with the installation of excessively robust firewall software on the Mac blocking Bonjour's ability to discover network devices. VPN client software is sometimes also a culprit, for the same reasons. You have already indicated this could not possibly be the cause of your problems.

Airport express not listed in Airport admin utility, no music

I had my stereo connected to my airport express to stream music from my imac.
Its been working great for a year. About 2 days ago I did some updates and now
the light is blinking orange and no music.
I have tried to reset the AE with a paperclip but its still not showing in the Airport Admin Utility NOR the Airport Setup Assistant.
Not sure where to go from here....
thanks Laura Drew

When I open the Airport Admin Utility, even when the AX is connected via ethernet, it is still not listed there. I hit rescan and it never surfaces. If I hit OTHER I get a screen that says 10.0.0.1 (if I remember correctly) then I put in the pw public.
10.0.0.1 would be the correct default LAN IP address for the AirPort Base Stations.
The screen says its rebooting the AX. The light turns green for apx. 2 seconds then turns back to blinking orange.
If I unplug it from the ethernet, I am able to see it under the airport icon.
And this would be normal when the AX is not connected to a network. I have assumed that your are using a Cable/DSL modem for your Internet connectivity and that you had not replaced the Ethernet cable between the modem and the AX just yet. So a blinking amber (orange) status light would be correct.
I choose it, plug the AX into the stereo but the light never turns green, and itunes says it can't find the AX.
Connecting the AX to a stereo would not change the status light. Again, remember a green status light indicates a valid network connection.
Maybe I will need to do it thru my router?? could my airport card have gone bad? but it seems I can connect to other networks (my neighbors)??
You can certainly set up the AX while it's connected to a router. I agree with you that it shouldn't be a problem with your AirPort Card.
So now I have to admit, I'm a bit baffled about your current network configuration. My confusion is, whether or not, you are using an Internet router, in addition to the AX.
Would you please confirm for me which of the following two network configurations, 1 or 2, that you currently desire...
1) DSL/Cable modem > (Ethernet cable) > [WAN port] Internet router [LAN port] > (Ethernet cable) > [Ethernet port] AX [Audio port] > (audio cable) > stereo, or
2) DSL/Cable modem > (Ethernet cable) > [Ethernet port] AX [Audio port] > (audio cable) > stereo
...or something else?
In other words, are you using the AX for both your Internet connectivity/iTunes streaming or another router for the Internet and just using the AX for streaming iTunes?

How can I reinstall airport setup assistant & airport admin utility

It's a long story but I accidentally deleted my support software for my Airport Express (the airport setup assistant and airport admin utility).
I tried downloading the AirPort 4.1 update, but I can't install it because I am told there is a newer version already installed on my computer.
I have no idea how to get the airport express software back, aside from re-installing my OS, which I would rather not do.
G4 12" Mac OS X (10.4)

"There must be something somehwhere on the system that makes the computer think that the original software is still there."
Hi ChezFerranti!
Yes, an installation receipt. Deleting receipts is not recommended.
It's probably best to download and install the 10.4.9 Combo Update, and that should re-insert the two missing utilities into your OS, since it wouldn't depend on seeing a receipt.
The pertinent receipt is "AirPortConfigApps.pkg" in HDD>Library>Receipts. That was the installation of the AirPort 4.2 software Update in July of 2005. It is no longer a separate item at Downloads, except for someone with a Panther OS (10.3). This means that it was folded into a later OS X Tiger Software Update, which is why the 10.4.9 Combo Update should be able to replace those utilities for you. The problem with simply deleting the receipt is that when you install a new version, then you'd get duplicate files of everything else that was part of that July 2005 AirPort 4.2 Update.
"aside from re-installing my OS, which I would rather not do"
There should be no need to do that. The 10.4.9 Combo Update should do essentially the same thing for you, W/O duplicating anything! Best of luck:)
Message was edited by: myhighway

Airport Admin Utility Not Picking up my Network

I am connected to my Airport, and using the Internet. However, neither Airport Admin Utility or Airport Setup Assistant picks up my network (when I scan for it).
Can someone provide me with some step-by-step instructions on how to solve this?
Thanks,
Shawn

Markku Lepistö :
Hi,
it seems the original poster's OS is: 10.3.9. I think I have the same issue.
-> with my 1.67GHz powerbook G4, 10.3.9 - after upgrading the internal airport software to 4.2, I can no longer connect to old access points. This Apple help page worked with 4.1 - holding down the Control key while selecting the network. Now with 4.2 it does not work anymore.
http://docs.info.apple.com/article.html?artnum=107938
Daamn, why did I accept the upgrade?! now I cannot connect to any WLAN in the office anymore! How to downgrade the powerbook airport drivers to 4.1?
Guys, please check your Apps->Utilities->Console output. Are you getting this too?:
"WirelessJoin unexpected status: 4".
I'm also haveing the same problem with my iBook G4. Is there anyway to downgrade it? Does anyone have a solution to this problem?

Computer can not read airport admin utility.

Similar Messages

Maybe you are looking for