Computer crash? Can't get past the setup assistant

I recently added leopard to my Power PC dual g5 and it has run terribly, so added memory today, worked ok for about 5 minutes then froze, manually shut off - which I have had to do several times since installing Leopard. When I turned it back on the setup assistant appeared, went through the assistant but it just keeps reappearing - it won't go past it. Restarted in safe mode and did a disk repair, it said the volume header needed a minor repair and it fixed it. Restarted but still back to the assistant issue. Please help!
Message was edited by: tjbug

Were you able to solve this problem? I am now encountering the same problem... thanks

Similar Messages

I recently added photoshop elements 12 to my computer but can't get past the initial log in screen. It goes gray and spins. any thoughts?

I recently added photoshop elements 12 to my computer but can't get past the initial log in screen. It goes gray and spins. I have a current serial number and log in ID/password but still not working. Any thoughts?

Hello,
I recommend you contact AT&T's dedicated BB Support staff (call their front line, request escalation to BB Support) and have them check to be sure that your account with them is correctly configured for this device. Sometimes when switching devices things don't fully automatically move behind the scenes, and only they (ATT) can validate that.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

I can not get past the setup screen on my reader. What am I doing wrong?

I can not get past the setup screen on my reader. What can I do?

I have no idea what you mean; can you post a screenshot?

HT4623 I have an iPhone 4 and have installed iOS 7, but I can't get past the setup. It gets hung up on agreeing to terms and conditions. Anyone know how to fix?

The setup hangs up at 'agreeing to terms and condtions'. Anyone know how to fix?

I seem to have gotten around the issue. I set the date of my iPad to 1 month prior (July), restarted the iPad, and the session timeout blockade went away. Many folks are saying this worked if they changed the date on their Mac or iPad or whatever device they were using for the update.

HT201269 How do you get to the setup assistant if the iphone was already setup?

How can I get to the setup assistant if the iPhone is already setup?

Hey Toddheel,
Thanks for the question, and great question by the way. If you have a device that has already been setup, you can erase it to return to the iOS Setup Assistant:
If you've already set up your device, you can erase all current content to go through the iOS Setup Assistant again. Tap Settings > General > Reset > Erase All Content and Settings. Do this only if you already have a backup, because this step will remove all current content from your device.
iOS: Back up and restore your iOS device with iCloud or iTunes
http://support.apple.com/kb/ht1766
Thanks,
Matt M.

I already have a valid payment method for my iTunes account, but can't get past the Family Sharing setup prompt telling me to add a payment method . What to do?

I already have a valid payment method for my iTunes account, but can't get past the Family Sharing setup prompt telling me to add a payment method . What to do?

I had the same problem and found a bunch of others did, too. Unfortunately all the posts had no responses! Anyway, I previously had my payment method linked to my paypal. I tried changing it to my credit card and it worked. Don't know if there's a bug with using paypal but that seemed to be the culprit for me. Good luck!

My computer beeps when I turn it on . I have tried to reset pram but can't get past the beeps.

My computer beeps when I turn it on . I have tried to reset pram but can't get past the beeps.

The beeps (or flashes) are usually an indication that there is no working RAM. This article gives some examples, but the concept applies widely across many Mac models.
iMac (Mid 2007) and later models: About startup tones

My computer crashed, can i get the music on my Ipod to my new machine?

My computer crashed, can I get the music on my Ipod in to my new machine?

iTunes: How to move your music to a new computer

I want to use this phone w/o a verizon account or number, but I can't get past the set-up screen. Can I use this phone to surf there web only and get past setup

I just want to use the phone as a web browser using wireless, I don't have verizon, I can't get past the set-up screen. Can I use the phone without a verizon account?

I took it to Verizon and a counter person got it to work. she said one has to be persistent and eventually the screen goes away that was demanding the phone number I didn't have, it works now I'm happy

My MacBook Air can't get past the gray screen with the apple logo. What's the fix?

My MacBook Air can't get past the gray screen with the Apple logo, so I can't login. Does anyone know the fix for this?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
How to use and troubleshoot FireWire target disk mode
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Before reconnecting an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, reboot as usual (i.e., not in safe mode.) If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see above for instructions.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it produces. Look for the line "Permissions repaired successfully" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

Ipad screen is white. Restored it on iTunes. Press home and on switch goes black then back to white with no logo at all. Can't get past the white screen. This happened after running app updates. 16GB OS 7.1.1

The ipad screen is white. Holding buttons didn't work so I restored it on iTunes. When I press home and on switch, the screen is white, goes black then back to white with no logo at all. Can't get past the white screen. This happened after running app updates. Is there any fix besides going to Apple store? In iTunes on computer can see what is on there. 16GB OS 7.1.1

FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary.

HT202649 Hello, I just bought a used iPhone 4S but can't get past the ID to continue set up. I went to iforgot as requested to reset my password to my existing account. Still can't get past the ID.

Hello,
I am having setup issues with a used 4S iphone. I can't get past the Apple ID step.
First it said it was an existing ID and I should go to iforgot and reset my password.
I did, but still keep getting the error message.
Then I entered the serial number online support and it said the ID was another account. Would that be the seller?
Do I need to get them to unregister under their name before I can proceed? Or...
Please help. I start new job on Monday that required me to have a smartphone. I need it up and running.
Thank you
R

Yes, you have encountered Activation Lock (Find My iPhone Activation Lock - Apple Support). The only way that phone will ever be usable is if the owner the phone is locked to releases it (see: Find My iPhone Activation Lock: Removing a device from a previous owner’s account - Apple Support). If you are lucky the phone is locked to the seller, so you can ask them to unlock it. If the seller is merely a middleman and the previous owner is not the seller it gets much more complicated. It's even possible that you bought a stolen phone, in which case you will never be able to use it and you should return it for a refund.

Rebooting old mac g5: Can't get past the grey screen.

This problem concerns an old mac g5 that I had replaced three years ago because it hadn't been working properly. I am getting it out because my son needs a computer and I was hoping that the thing would work for a little while.
I can't get past the grey apple screen. I have the installation disc in and restart while pressing the c. I just am not getting any further than that. The fans begin to sound like a jet taking off. I have tried resetting the pram while starting up, but that doesn't seem to be working either. I have heard about a hair dryer trick and don't really know what is supposed to get warmed up by that.
Does anyone have any suggestions?
Thanks.

No hair dryer. What you need to do is make sure the PRAM battery is new. It is a coin shaped battery on the logic board. Radio Shack sells them.
Option key booting sometimes works. You have to us a Mac OS X 10.5 or 10.4.6 retail disc, which are black with a white X logo, and do not say Update Dropin or OEM on them. If you have the original iMac G5 disc that's fine, but web browsing with older operating systems is not very friendly. Some of these machines were known to have leaky capacitors, and getting the power supply replaced on them now would be quite hard because of the age.
http://www.ifixit.com/ may be able to help if you suspect that.

I am unable to get past the apple login screens on my iPad to access my settings menu for a new home network. My password is not recognized so I cannot even get into the settings mode to make a chance. How can I get past the Apple logins?

I am unable to get past the apple login screens on my iPad to access my settings menu for a new home network. My Apple password is not recognized so I cannot even get into the settings mode to make a chance. How can I get past the Apple logins?

Hey Dpcupcake,
If you can not get past the sign in screen on your iPad, you will need to use the steps in this article to recover use of your iPad -
Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support
Thanks for using Apple Support Communities.
Happy computing,
Brett L

I updated my IPhone 3GS to the newest software version, now I can't get past the activation stage. AT

I updated my iPhone 3GS to the new version 6.1.3 and installed the new software. After doing this, I can't get past the activation stage in the process. I had AT&T and the phone doctors look at it and they couldn't figure it out. Apple wants $175 for me to send it in but I shouldn't have to pay for an update malfunction. I am at the mercy of the good folks in Apple land to help me.

Is your carrier still AT&T? What error message do you get when you try to activate it?
Have you tried a new SIM? Was the phone jailbroken? Was the computer you used to update it ever used to jailbreak a phone? In general, this problem is caused by one of the following:
1. Your antivirus is blocking access to gs.apple.com.
2. Your phone is jailbroken.
3. Your computer has been used at some time in the past to jaibreak some iOS device (not necessarily the phone with the problem), and its network database was corrupted by the hacking software that was used.
4. Apple's activation servers are down (very rare, and never for more than an hour or so).
For 1. try disabling your antivirus.
For 2. & 3. you need to go somewhere other than an apple forum for help. Although you can try deleting lines containing gs.apple.com from your "hosts" file on your computer.

Computer crash? Can't get past the setup assistant

Similar Messages

Maybe you are looking for