Computer disabled - 3rd post

This topic has been posted twice before, once in the Quicktime forum where I was asked to post it here. Refer to this link for most recent background info.
http://discussions.apple.com/thread.jspa?messageID=4251703
• I have since run DISKWARRIOR which found some issues and corrected them. I still cannot open in OS 10.3.9. The spinning color disc appears and everything is frozen.
• I did a Target Disc Mode file transfer as suggested.
I can delete this system and rebuild OS 10.3.9 in the new HD but it would be nice to overcome and correct this issue. All I set out to do was download and install Flip4Mac so that I could view .wmv files.
Any suggestions?

"Why is hotmail being boycotted ? "
Because it doesn't work correctly. (users receive blank e-mails from forum)
Start from "LOAD BIOS OPTIMIZED DEFAULTS", then get Memtest86 and check memory for error(s). Details can be found here: https://forum-en.msi.com/index.php?topic=103598.msg760534#msg760534

Similar Messages

  • N260GTX-OC, computer will not POST

    Hi everybody,
    I recently got an MSI GTX 260, and after installing it my computer would not POST. I had an 8600 GT, switched the cards out an my computer turns on for about 5 seconds, then turns off and reboots, continuously. I had a Cooler Master 500W, but saw it was only pushing 32A over the +12v rails. So I went out and bought a BFG GS-650W which puts out 40A over +12v, so thats over the required 36A. Everything is disconnected expect RAM, CPU, Gfx card, and one SATA DVD drive. I don't have another machine to test the card in, so is there anyway I can tell if the PSU is still underpowered or if it's the card?
    Full specs:
    Gigabyte P35-DS3R
    Core 2 Duo E6750 (was OC'd to 3.0, but I put it back to the stock 2.66)
    2 GB DDR2-800
    MSI N260GTX-OC 896MB (i hope?)
    X-Fi Platinum
    BFG GS-650W PSU

    I live in Germany so I'm not familiar with MIR system at newegg and therefor let you correct me
    As far as I know the output of Corsair psus is rated at 50°C while PC P&C rates continous output at 40°C which is a bit more ideal. Also Corsair doesn't really make psus so the TX650 is to my knowledge made by Seasonic (TX750 is Channel Well) who have also an excellent reputation for psus.
    At least both are great units and one can't do anything wrong deciding between the two. It's more or less a question of personal preferences. I don't think one of them is really a better buy because of technical reasons.
    I have to correct you a bit about the popularity and availability of PC P&C in Europe. Well, I can only speak for Germany but over here those units are easiely available in most shops. There's no difference to the States. Price level is almost the same with Corsair TX series and got quite low by now. Without any rebates TX650 and Silencer 610 are about $108/€80.

  • Computer unable to post.

    1.  Specs
    KB SAITEK|ECLIPSE KEYBOARD PZ30AU - Retail (Qty=1, Price=$49.99)
    HD 80G|WD 7K 8M SATA2 WD800JD % - OEM (Qty=1, Price=$42.99)
    DVD BURN LITE-ON|DH-20A4P-04 20X % - OEM (Qty=1, Price=$25.99)
    MB MSI K9A2 PLATINUM 790FX AM2+ RTL - Retail (Qty=1, Price=$179.99)
    CASE ANTEC|NINE HUNDRED BK RT - Retail (Qty=1, Price=$114.99)
    VGA SAPPHIRE 100226L HD3850 512M RT - Retail (Qty=1, Price=$189.99)
    PSU ANTEC|TP3-650 RT - Retail (Qty=1, Price=$109.99)
    CPU AMD|A64 X2 6000 3.0G AM2 2x1M R - Retail (Qty=1, Price=$159.99)
    MEM 1Gx2|KST DII800 KVR800D2K2/2GR - Retail (Qty=1, Price=$44.99)
    MOUSE LOGITECH|TRACKMAN WHEEL RTL - Retail (Qty=1, Price=$24.99)
    THERMAL GREASE ZALMAN|ZM - STG1 RTL - Retail (Qty=1, Price=$9.99)
    CPU FAN ZALMAN | 9500A - Retail (Qty=1, Price=$48.99)
    2.  attempted solutions (keep in mind I always discharge myslef by touching metal before and after I touch any component)
    checked all wiring
    checked all componets to see if they where all inserted correctly
    cleared cmos
    unplugged everything and waited an hour
    tried diffrent video card
    checked if video card was ok with another system (it is)
    tried ram in back two slots (i have 2 ram sticks)
    tried ram in one slot then switched around and tried the other
    unplugged every component from power supply except motherboard and video card
    unmounted motherboard and placed it on a sheet of cardboard.
    checked for any oozing of thermal paste
    turned on motherbard while on cardboard
    kept the powersupply plugged in over night to see if capacitors would charge enough to get a post
    3.  What exactly happend.
    I built the computer a few weeks ago and updated all the drivers.  I have played through bio shock perfectly with no problems.  I have a graphics program called LightWave 3d ver 8.3.    Ran it perfectly as well. I also ran it through 3dsMax and scored fairly high(higher then most but still below the hard core junkies)  About a few days ago the computer started locking up randomly, forcing me to reset.  I started looking for solutions for this instability through my manual's.  I disabled spread spectrum to see if the system would be stabler.  Afterwords the computer locks up just as the last item loads up on the task bar.  So I re enabled it.  Then the system again locks up.  Only this time when i reset I get no post just a blank screen, the cpu fan comes on as well as video card fan.  The Led lights on mobo come on as well.  I've tried resetting it over and over again with no positive results.  Near as I can figure its one of three things.  the PSU, mobo or cpu.   I think I can rule out the cpu, because if it was bad already it wouldn't of let me played through bioshock perfectly.  I would of probably of gotten some choppy graphics or poor performance, something that would of indicated a cpu problem.  I chose this PSU because it was highly recomended by a lot of people.  If you do a search you can find multiple places where hundreds of people have given this item high reviews.  I am completly stumped as to what to do next.  Wouldn't normaly come to a forum but I have no clue what to do except re ship all three items.  But before I do that I need to find out if maybe there is an incompatibility issue with this type of PSU.   Deep down I think the capacitors on the PSU where origionally fully charged, but over time they have drained and now only enouch go go juice to run lights and fans.
    on a side note.  Why is hotmail being boycotted ?  its no diffrent than Gmail

    "Why is hotmail being boycotted ? "
    Because it doesn't work correctly. (users receive blank e-mails from forum)
    Start from "LOAD BIOS OPTIMIZED DEFAULTS", then get Memtest86 and check memory for error(s). Details can be found here: https://forum-en.msi.com/index.php?topic=103598.msg760534#msg760534

  • Computer freezes after Post (Cannot load/re-install windows)

    Hi!
    I have the K8T Neo-FIS2R motherboard 1.7 bios with an AMD Athlon 64 3000+  The computer loads up correctly, sees all of the memory, both CD rom drives, and both hard drives.  However, after the post my computer goes to the Load win XP in safe mode etc. and the computer freezes right there.  Also, when i try to reinstall windows XP, I just get past the boot from CD option and when it says setup is examining system hardware, it freezes at this screen and will not go any further; also when it does this, my numlock key blinks for some reason.  Any answers???

    Quote
    Originally posted by MSUHattrick
    fixed... just had to disable Legacy USB support
    That would have been our next route.. haha
    Good to hear, bro.
    Ian

  • Computer disabled - Quicktime & Flip4mac

    It used to be that I could view videos received via email (wmv, etc) I lost that many, many months ago. I upgraded and now am at latest version of QT (7.1.5?). Today I decided to do something about this and read some discussions and downloaded Flip4Mac. Well - it never finished the download. I have a spinning disc (cursor) and can do absolutely nothing except to restart from restart button or unplug. Every time that I turn the computer on I have several seconds before this takes over but then I'm stuck with this spinning disc (acting as if downloading I suppose).
    I cannot force quit.
    I tried to start holding the shift key down when restarting. No difference.
    I tried to reset PRAM - no difference.
    I don't have the software CD as I bought this particular G4 second hand.
    HELP?
    G4 400 w/1 GB Ram MAC OS (10.3.9)   Mac OS X (10.3.9)   Dual boot to OS 9.2.2

    Prairiewolf, you cannot use machine specific CDs from one mac to another. If you do, you will do damage to your system.
    As I suggested previously, you will need to contact the seller & obtain the original System Install CDs that came w/the computer. Per Apple's License Agreement it is illegal to sell Mac computers without the System CDs that originally came w/the computer. The reason being is because they are *machine specific.*
    You may be able to get replacement System Install & Restore CDs from Apple's Customer Support - in the US, (800) 767-2775 or 800-275-2273 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.
    Or you may need to puchase a retail univeral full installer CDs.
    Regarding OS 9.1 or OS 9.2.1, ask the vendors the color of the CD lable. All universal full install CDs are white w/an orange/golden 9.x on it.
    http://store.yahoo.com/hardcoremac/index.html(RECOMMENDED BY APPLE)
    http://welovemacs.com/apsyso.html
    http://www.applerescue.com
    Do NOT buy a gray installation CD - those are not universal installers but model-specific [NO matter what the seller says about them!] OEM-versions have caused problems in the past when used on other computer models.
    *The above is the same if you decide to purchase off of eBay.*
    Furthermore, as this is a forum for QuickTime issues, you need to repost all your current issues in the Panther forums. Please see the Panther Forum link in my March 11, 2007 post in this thread.
    Good luck!

  • HT2250 how do i enable bonjour. someone i let use the computer disabled it. help!!!

    hello, i am sharcorb and would like to ask a question.  i need someones help with enabling bonjour on windows 7. i let someone use my computer and now i cannot enable it.

    Welcome To Apple Discussions!!!
    You are going to need a DVD ripper...
    might I suggest this one...
    http://www.magicdvdripper.com
    Then you will need to convert into the correct format...
    MPEG-4 or H.264 using a converter
    might I suggest this one...
    Videora iPod Converter...
    Ripp DVD, convert into format, then put onto iTunes...
    post back for questions..
    YQ

  • Computer disabled - help

    I hope someone can help me with this problem. I have had this powerbook 4 years now and love it... recently signed up for broadband using cable. nothing else different. Sunday, sent a few e mails, etc.etc. upgraded security from mac. 2007 - 2008. Left cable in! when I returned and tried to start up power up , initial noise sounds as if its about to start then black screen and flashing light on front sleep button and sound like engaged tone. Tried all sorts of combinations but nothing. Is this the end of my wonderful mac or has it disabled itself for a reason or what!!! Hope someone can suggest something. Im using library to send this question off and will log in periodically ...also going to try and source a shop in Gateshead for Apple technical assistance but would appreciate some help from others. thanks.

    Hi, meetoo2, and welcome to Apple discussions.
    ...sound like engaged tone...
    Do you mean by this that the computer beeps loudly while trying to start up? If so, *how many times* does it beep before stopping? The number of beeps will help to identify the problem.
    ...flashing light on front sleep button...
    It sounds as though your Powerbook may be Aluminum rather than Titanium (this is a Ti forum). If most of its ports are on its rear panel, between two separate hinges, it's Titanium. If all of them are on its side panels, it's Aluminum. There's a separate set of forums devoted to the 15" Aluminum models.

  • Computer won't POST on cold starts

    When I turn on the computer after not having used it for over an hour or so, it won't post. Everything turns on, except the monitor. The only way I can turn off my system after it posts, and the monitor is still off, is by turning off the power supply. I found a way of turning it on when doing a cold start, but its really annoying to do. I do this by turning off the PSU, and unplug the monitor from my vid card, and then plug it back in. After doing this, system will turn on no problem. How do I solve this? I know monitor and vid card work good, since they work perfect in my other system.
    Oh one more thing, after having a successful start, and having loaded Windows, my CD-RW is looping, the light stays on, until I open/close it, then it stops. Any suggestions?
    Oh and I use K8N Neo-FSR.
    Edit: PSU is an Antec TruePower 380. 18 amps on the +12v line.

    Hi,
    I've had lot's of trouble with my system. It didn't POST either. The problem you describe is not the same, but I see you are using the same video card as I do.
    My problem was 'resolved' by upgrading the bios version 1.52
    I've seen quite a lot of messages indicating that it could be the power supply, being too weak etc... Personally, I do not think it is. In my view it has something to do with timing, and bios 1.52 resolved it for me.
    Good luck with it; this issue is a time consumer ...

  • Disable IPv6 post EPM configuration

    Hello Gurus,
    Consider the following scenario:
    1. Oracle EPM 11.1.2.3 is installed and configured on the server when IPv6 was enabled.
    2. When I check the logs, there are errors like the one shown below for all the Hyperion products in the sysout logs.
    <Feb 26, 2015 4:52:14 PM IST> <Warning> <JMX> <BEA-149509> <Unable to establish JMX Connectivity with the Adminstration Server AdminServer at service:jmx:t3://[2001:0:9d38:90d7:1498:37fa:53ef:9b94]:7001/jndi/weblogic.management.mbeanservers.domainruntime.
    java.io.IOException
      at weblogic.management.remote.common.ClientProviderBase.makeConnection(ClientProviderBase.java:196)
      at weblogic.management.remote.common.ClientProviderBase.newJMXConnector(ClientProviderBase.java:84)
      at javax.management.remote.JMXConnectorFactory.newJMXConnector(JMXConnectorFactory.java:338)
      at javax.management.remote.JMXConnectorFactory.connect(JMXConnectorFactory.java:247)
      at weblogic.management.mbeanservers.runtime.internal.RegisterWithDomainRuntimeService.getDomainMBeanServerConnection(RegisterWithDomainRuntimeService.java:222)
      Truncated. see log file for complete stacktrace
    Caused By: javax.naming.CommunicationException [Root exception is java.net.ConnectException: t3://[2001:0:9d38:90d7:1498:37fa:53ef:9b94]:7001: Destination unreachable; nested exception is:
      java.net.ConnectException: Connection timed out: connect; No available router to destination]
      at weblogic.jndi.internal.ExceptionTranslator.toNamingException(ExceptionTranslator.java:40)
      at weblogic.jndi.WLInitialContextFactoryDelegate.toNamingException(WLInitialContextFactoryDelegate.java:792)
      at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:368)
      at weblogic.jndi.Environment.getContext(Environment.java:315)
      at weblogic.jndi.Environment.getContext(Environment.java:285)
      Truncated. see log file for complete stacktrace
    which I presume is because IPv6 is enabled on the server.
    When I check the status of the server in Oracle Weblogic Administration Console, I see the status as Shutdown, however the service is up and running and I am able to work on it.
    Doubt:
    Can I disable IPv6 on the servers, such that it doesn't disturb the current configuration?
    Will there be any extra need to configure EPM system after disabling the IPv6?

    If you want to disable IPv6 then you can but make sure you bring down Hyperion, completely remove IPv6 and then reboot.
    From the log you posted it looks it is trying to bind to a tunnel adaptor or 6to4 adaptor, if you run an ipconfig /all you should see what it is binding to.
    If you would like to understand ipv4/ipv4 supported combinations have a look at the "IPv6 Certification" tab in the support matrix - Supported Platforms Matrices - Oracle Enterprise Performance Management System
    From
    Cheers
    John
    http://john-goodwin.blogspot.com/

  • Removing a Computer/ Disabling Wireless on Linksys WRT54G

    The interface for adding a computer is easy enough. How do I remove one? Right now there are multiple unknown units that are greyed out (I assume to mean inactive), but I want to actually remove them. Second- Is there a way to totally disable the wireless capability of my router, though not for good. I purchased a wireless in case I ever want to go wireless, but for now all of my units are wired into the router, so I want to make sure it isn't accessible except by wire. Thanks for any help.

    the easiest way to disable the wireless is to go into the router settings and disable the wireless, click in the router and log in, then go to the wireless setting.
    the items that are grayed out are already disconnected and you can remove the items you don't want by right clicking on them and then just click remove.

  • Custom Install on "My Computer" - Disabled?!?

    Okay so this is not one of my best mornings. I managed to delete my iTunes library (I thought it was a duplicate) and now when I try to load iTunes it won't work.
    No biggie I head over to Apple and download a new copy. I get as far as the Custom Install page and it won't let me click on the three things as it says next to them 'disabled'. I have about 30 GB available so I don't think its a memory issue.
    Does anyone know what I might have done?

    Remove the 'iTunesX.pkg' file from ./Library/Receipts.
    Try installing again. This time it should work.
    Did you delete the entire iTunes folder?
    Deleting the library should not prevent iTunes from operating.
    iTunes will create a new empty library, but operate as normal.
    M

  • ITunes 7.+Compatability with Ask the DJ 3rd post--getting nowhere

    A problem came up with my new MBP. When transfer a group of songs to be crossfaded & matched from iTunes 7.+ to Ask the Dj (ATDJ), the song/s playback on ATDJ garbled & then stops. Can't mix them now to match BPM & volumn and crossfade. These songs are ripped from CDs & other downloads. Any suggestions.

    Did you use a tracked service like Regular Parcel on this $30 item?If so, when the item is delivered the postie will mark it delivered.After that, the twit is on his own.Give him the tracking number and the Canada Post website (canadapost.ca) so he can see for himself. If not, he will have to talk to his upstairs neighbour, who I presume picks up and passes on all his mail, and let them know he is expecting a parcel. Let him know what the package looks like (kraft envelope/ white paper/ PO box/ poly envelope). Oh and add him to your Blocked Bidder List. Too much drama.  

  • Laptop Stolen, now How can I get Ipod working with new computer/disable old

    My laptop with my itunes was stolen. I still have my IPOD 30GB.....
    I have a new computer, and I think I can download Itunes to it and hook up the ipod and it will be able to load ipod content to the new computer???
    Also I am worried, what about the old computer, do i need to DeAuthorize it? How would I do that since I don't have it in my possession?
    Thanks for any help!!!!

    *what about the old computer, do i need to DeAuthorize it? How would I do that since I don't have it in my possession?*
    You can't deauthorise a computer you no longer have access to on it's own. However once you reach the limit of 5 authorisations you have the option once a year to deauthorise them all in one go and start over: About iTunes Music Store Authorisation and Deauthorisation
    *I have a new computer, and I think I can download Itunes to it and hook up the ipod and it will be able to load ipod content to the new computer???*
    If your iPod is set to update automatically you need to take care connecting to an empty iTunes. If it is set to update automatically you'll get a message that it is linked to a different library and asking if you want to link to this one and replace all your songs etc, press "Cancel". Pressing "Erase and Sync" will irretrievably remove all the songs from your iPod. Your iPod should appear in the iTunes source list from where you can change the update setting to manual and use your iPod without the risk of accidentally erasing it. Also when using most of the utilities listed below your iPod needs to be enabled for disc use, changing to manual update will do this by default. Check the "manually manage music and videos" box in Summary then press the Apply button: Managing content manually on iPod
    Once you are safely connected there are a few things you can do to restore your iTunes from the iPod. If you have any iTunes Music Store purchases the transfer of purchased content from the iPod to authorised computers was introduced with iTunes 7. You'll find details in this article: Copying iTunes Store purchases from your iPod to a computer
    The transfer of content from other sources such as songs imported from CD is designed by default to be one way from iTunes to iPod. However there are a number of third party utilities that you can use to retrieve the music files and playlists from your iPod. You'll find that they have varying degrees of functionality and some will transfer movies, videos, photos, podcasts and games as well. Have a look at the web pages and documentation, this is just a small selection of what's available, they are generally quite straightforward. You can read reviews of some of them here: Wired News - Rescue Your Stranded Tunes
    TuneJack Windows Only
    iPod2PC Windows Only
    iGadget Windows Only
    iDump Windows Only
    iRepo Mac and Windows
    iPodRip Mac & Windows
    YamiPod Mac and Windows
    Music Rescue Mac & Windows
    iPodCopy Mac and Windows
    There is also a manual method of accessing the iPod's hard drive and copying songs back to iTunes on Windows or a Mac. The procedure is a bit involved and won't recover playlists but if you're interested it's available at this link: Two-way Street: Moving Music Off the iPod
    Whichever of these retrieval methods you choose, keep your iPod in manual mode until you have reloaded your iTunes and you are happy with your playlists etc then it will be safe to return it auto-sync. I would also advise that you get yourself an external hard drive and back your stuff up, relying on an iPod as your sole backup is not a good idea and external drives are comparatively inexpensive these days, you can get loads of storage for a reasonable outlay.

  • THIS IS REALLY ANNOYING, THIS IS MY 3RD POST.BEEN 6 MONTHS.CANT FIX IPOD :(

    I have a 2Gb nano, one of the older ones. and i get the folder icon with the exclamation mark next to it.
    tried to restore and update with itunes - it takes a while to restore it, then tells me that its reseting the ipod and it should appear in itunes soon. it does appear in itunes but the same warning pops up telling me that it is corrupted again and needs to be restored.
    i click restore and this time itunes tells me it cant restore it because it was unable to download the sufficient software needed. the exact error message is:
    "There was a problem downloading the ipod software for the ipod "ipod". The requested resource was not found."
    whats going on? this is a continuous circle. i tried to format the F drive in 'my computer' but nothing happens.
    i am using the most recent version on itunes and the latest version of iPod firmware.
    i have tried Chkdsk on my ipod with no result.
    i have also tried formatting and Chkdsk in disk mode with no result.
    i have tried ipod updater on my other computer and apparently it cannot 'mount' ipod.
    i have gone to computer managment but it's saying my ipod is 'unreadable' and wont let me do anything with it. the same thing happens when i try to format it in my computer, it doesnt allow it.
    can someone help me? i would really appreciate it as I have been trying for weeks, no MONTHS, to get this fixed. THANKYOU XXXX XXX XXX
    ps. i live in the uk, is there anywhere i can send my ipod away to get fixed?

    This is the itunes forum.
    You are not addressing Apple here at all.

  • For the 3rd post I need help..

    Ok so I realized I was posting on a no fb account for some reason.. Basically my story goes like this , I've started selling on eBay again. I recently got a very new buyer Contacting me every 10 min asking me questions after purchasing an item such as what is the condition does it work etc.. He then paid 3 days later he has 0 fb.. He asked me 1 day after he will get the item I explained he will get it in the mail box .. He said what if I'm not home I said no the key mailbox that everyone shares the brown one with the slots.. It took me about a day of messaging back and forth how it works.. The next day he says he lives in the basement of a house and there renting .. I ask if he has access to the mailbox we talk about ... Nop he doesn't... So I tell him to ask the owner . For the key It's been 7 days now ( 5 business days) he said he checked the box and it has not arrived.. He lives 2 hours from me So I'm assuming it was there a day after I shipped maybe 2.  Does anyone know what happens if mail stays in the big slot of the mailbox for more than a few days is it returned to the owner? I ask this because there are so many people getting mail now and there are only 2 big slots for a whole street! I really don't want to light 30$ on fire because this guy had no clue what he was doing.

    Did you use a tracked service like Regular Parcel on this $30 item?If so, when the item is delivered the postie will mark it delivered.After that, the twit is on his own.Give him the tracking number and the Canada Post website (canadapost.ca) so he can see for himself. If not, he will have to talk to his upstairs neighbour, who I presume picks up and passes on all his mail, and let them know he is expecting a parcel. Let him know what the package looks like (kraft envelope/ white paper/ PO box/ poly envelope). Oh and add him to your Blocked Bidder List. Too much drama.  

Maybe you are looking for