Computer does not boot when pxi 1033 is connected

hiiiiii...........i am using NI pxi-1033 for my application & this pxi is connected to my system through PCIe-8361. i am using it from last 10 months, now suddenly my computer does not boot up. i start pxi first then start the computer but computer screen shows no signal. there is no blue screen error.
can you give me any point to troubleshoot the problem.

This probably doesn't help, since your setup used to work, but I have had to run the MXI Compatibility Tool on more than one PC.
http://joule.ni.com/nidu/cds/view/p/id/3119/lang/en
One PC would only boot one time in ten, before running the tool.

Similar Messages

  • KT6V + sempron 2800 does not boot when BIOS saved

    Hi,
    I have just bought a new sempron 2800 to be use on a KT6V LSR. I plugget in my KT6V but was not recognised well (but all was working ok with windows). To be recognised, I have flashed with the last bios of MSI my motherboard... and now I have the following problem:
    - I clear CMOS, then boot. It comes ok (processor detected and set a 1200Mhz)
    - Then CMOS has a bad checksum: I enter setup, then load default, save.
    - I reboot: the computer does not boot up.
    If I re-clear CMOS I can re-enter setup and modify frequencies or other options. But when I save my modifications, then the computer does not reboot anymore (I have to re-clear cmos again)...
    I tried to apply the configuation I found in this thread:
    http://forums.amd.com/lofiversion/index.php/t69536.html
    It says that SDRAM must be at 333, FSB at 166 and multiplicator at 12. When applying this settings, it does not boot (the leds indicate that the chipset initialisation (the first step) does not pass).
    If I just load biios default, the leds indicates that it fails when checking the memory (second step of boot). I suspect that it's a problem of memory (but my memory was working well before !): it's 2x512 of DDR 400.
    Any suggestion is appreciated :D . I spent several hours trying to configure the bios but it does not boot..
    (I'll also try to find help on AMD forums...)
    (Some extra info: my PSU is 26A for 12V, so it seems that it's not due to the PSU (as I read in the FAQ of this forum).
    Thanks,
    Ptitmain.

    AMD Geode™ NX Processor Family & DB1500 Development Board
    Powerful Software Development Capability for AMD Geode™ NX Processors
    The AMD Geode™ NX processor family consists of three versatile and powerful products - the AMD Geode™ NX 1250@6W* processor, the AMD Geode™ NX 1500@6W processor** and the AMD Geode™ NX 1750@14W processor.***
    The AMD Geode™ NX processor family leverages advanced architecture to provide powerful solutions for a variety of Internet edge, peripheral applications, and more. The AMD Geode™ NX processor family provides the highest x86 performance for fanless operations.
    The NX processor family leverages Mobile AMD Athlon™ processor technology to deliver superior computing power for a variety of thin-client and other applications including point-of-sale terminals, kiosks, high-end printers and home media systems.
    Key features include:
        * Low-power consumption
        * Advanced 7th generation core
        * Long-term manufacturing and support
        * 128KB level 1 cache
    The AMD Geode™ NX processor family is supported by existing low-cost infrastructure, proven architecture and a long-term supply commitment.
    The Geode NX 1250@6W processor is based on an AMD Athlon™ core and demonstrates the company’s commitment to making enhancements to its x86 product offerings and delivering a full line of x86 products to market. The AMD Geode family of embedded solutions is part of AMD’s strategy to offer assets, resources and vision for extending x86 solutions from low-power embedded solutions up through the highest-performing server platforms. The Geode NX 1250@6W processor is a cost-effective solution for customers requiring sub-one gigahertz performance without a fan. Operating without a fan not only reduces design costs and allows for better power management, but also allows the processor to co-exist in virtually any environment because it can operate silently.
    The AMD Geode NX 1250@6W processor broadens the selection AMD’s customers have for x86 solutions that range from sub-one watt to 14 watts, allowing them to choose a processor that best meets their individual design needs.
    .13um fabrication process
    128/256KB L1/L2 cache
    266MHz Front-Side Bus
    Floating Point logic
    AMD PowerNow!™ technology
    Less than 6 watt  maybe i should replace my PSU with battery (typical) to 9 watt (maximum) Total System Power Dissipation
    Socket A compatibility
    3DNow!™, MMX™ and SSE Instruction Set

  • HT1277 Mail on my Mac computer does not update when I update my mail on my phone and iPad.  Can anyone help me with this?  Is there a setting I need to check?

    Mail on my Mac computer does not update when I update my mail on my iPhone and iPad. Can anyone help me with this?  Is there a setting that I need to check?

    All that you had to do was to sign into the old account in order to update those apps. What I mean is that you just needed to sign into that account in the store settings like I described and that should have worked. You didnt need to enter the credit card information again - you justed needed to use the old ID and password.
    Anyway, I think the good news is that if everything else is OK with the new account, just download iBooks with the new ID - it's a free app so its not like you have to pay for it again. I'm not sure what the other App is that you are talking about - but if it is the Apple Store App - that is free as well.
    Try this anyway, when you try to update iBooks, just use the old password if the old ID still pops up.
    Did you try signing into the store settings with your new ID and see what happens with the updates then?

  • Computer will not boot when I install my Sound Blaster Live Ca

    My computer wiil not boot when I put my sound blaster li've card in. Any body have any ideas that I could try?
    Thanks
    tbaker

    Turn off your pc, remove the jumper near the battary for 5 seconds, then put the jumper back.
    If it works go to BIOS and switch off (disable) Audio on Board or Sound on Board , (if you have it), then start your pc. Should work !!!
    I hope it helps!!!

  • I recently went from 10.4 to 10.6 and now itunes does not open when my phone is connected.

    I recently went from 10.4 to 10.6 and now itunes does not open when my phone is connected. I have an iphone 3.

    Connect your iPhone to your computer. Select it under Devices in the source list left side of the iTunes window.
    Select the Summary tab from the menu.
    Select:  Open iTunes when this iPhone is connected.

  • TS1410 My iPod shuffle ( 1st or 2nd generation) will not recharge and does not show when the doc is connected to my MacBook Pro. I'm running the latest updated version of iTunes.

    My iPod shuffle ( 1st or 2nd generation) will not recharge and does not show when the doc is connected to my MacBook Pro. I'm running the latest updated version of iTunes.

    Hello Jane Benstock,
    Thank you for using Apple Support Communities
    It sounds like the next best step to take would be to reset the iPod Shuffle.
    Check out this article named Resetting iPod shuffle found here http://support.apple.com/kb/HT1655.
    All the best,
    Sterling

  • HP Z620 does not boot when external Seagate hard drive is connected

    I'm troubleshooting an HP Z620 workstation with 32GB RAM, one 500GB HDD + one 1TB HDD running Win 7 Enterprise 64 bits, this user has 2 external USB 3.0 HDDs,  one Buffalo 2TB  + one Seagate Desktop Backup Plus 4TB; the problem comes when the external Seagate HDD is connected and the PC is turned one, for some reason the PC does not boots, it shows a message that states "Non-disk or no boot disk error" and sometimes it tries to boot, but then goes thru the "Windows repair option" or "Start Windows normally" routine, none of these results on starting the PC.
    The only way this PC starts and works properly is when PC is started with the external Seagate HDD disconnected and then connected once the Win 7 is up and running; the problem described above does not happens with the external Buffalo 2TB HDD and the Seagate HDD have been tested throughly and no errors or problems have been detected on it.
    I'll really appreciate your attention to this, as well as your prompt response.
    Regards,
    Gaspar Campos

    Hi:
    You may also want to post your question on the HP Business Support Forum -- z Workstations section where there may be more folks familiar with that issue.
    http://h30499.www3.hp.com/t5/Workstations-z-series-xw-series/bd-p/bsc-272#.U1k4uv1OXGg

  • System does not boot when PCIe express Card is inserted in system. Using Spartan-6 PCIe Integrated Endpoint Block 1.3

    Hi,
    I am using Spartan-6 PCIe Endpoint Block core v1.3 and I am using ISE 12.1. I have used the PIO example design,
    modified it according to our design.
    The core is configured as below:
    BAR0 - 8KB, 32-bit, Memory Type
    Lanes - x1
    Clock - 125 MHz (system clock)
    The card is a custom board. When the card is pluged into the system the system does not boots, it hangs.
    I have tried debugging using chipscope and monitored trn_lnk_up_n, trn_reset_n and trn_clk. trn_lnk_up_n stays
    high (deasserted), trn_reset_n stays low (asserted), trn_clk is low (No clk).
    What might be the issue?
    Thanks & Regards.

    Thanks Gabor, for the response.
    I refered couple of answer records like AR# 34873 and AR# 34894, I monitored trn_reset_n, sys_reset_n, clock_locked, PLLLKDET and RESETDONE signals as suggested in AR# 34894.
    Status as follows:
    SYS_RESET_N = 1 (deasserted)
    TRN_RESET_N = 0 (asserted)
    CLOCK_LOCKED = 0 (deasserted)
    PLLLKDET = 0 (deasserted)
    RESETDONE = 0 (deasserted)
    which means the transceiver PLL frequency is not within the predetermined tolerance. Is this problem related to the PCIe Jitter Attenuator I am using on the board to derive 125MHz from 100MHz system Clock.
    Thanks & Regards

  • Windows Server 2008 R2 Does not boot When Back up drive removed

    I have a windows Server 2008 R2 Standard server RAID 10 installed.  I  have a non raid drive installed as the backup HD.  The Backup drive is now failing. When I went to switch it with a new one the system does not boot and is asking for
    a boot drive.  I have been searching for solutions and cannot find any.  Any ideas?

    Hi,
    Could you confirm if your boot volume is on that non-RAID disk (maybe 2 volumes on that disk and one of them is the boot volume)?
    At current situation, first please test to connect the failed disk back to the device and see if it will help.
    Or you may need to run a boot-up repair with an installation disk. 
    If you have any feedback on our support, please send to [email protected]

  • Computer will not boot when iPod is connected

    Hi everyone,
    First time Mac user here, so I'm not very experienced when it comes to troubleshooting - there may be a very simple fix for this, but I've searched online and come up with nothing so far.
    I've recently bought a 20" Intel-based iMac (Core 2 Duo). I'm using Boot Camp (1.1.2 Beta) to dual boot with Windows. I already owned a 30gb iPod, which has previously been used with a Windows laptop. The iPod has disk mode enabled as I use it for transporting data as well as music and video.
    Now that I'm using the iMac as my main comptuer, I keep the iPod docked & connected whenever I'm not out of the house in order to keep it charged & synchronised. However, if the iMac has to restart for any reason (like switching between Mac OS and Windows, or rebooting after a system update), it will not continue booting after making the chime sound. The screen remains white, holding the option key does not display the Boot Camp menu, and no matter how long it's left like this it will not continue to boot either OS. Pressing the Power button causes the computer to immediately switch off. Turning it on again after removing the iPod from the dock results in it booting normally.
    Has anyone had any similar experiences?
    Thanks

    hi xJamez
    Welcome to Discussions
    Because you said you use the iPod as an external hard drive, I am going to assume that it's not a nano, shuffle, or mini. What I suspect is that the computer is trying to boot from the iPod because the iPod actually has a hard drive in it, and the iMac thinks that it's an external hard drive that it can boot from. In the future, I would disconnect the iPod before each time you shut-down or restart your iMac.
    Hope this Helps
    Trevor

  • Computer does not sleep when lid is closed

    Hey everyone,
    Until about 15 minutes ago I had my powerbook G4 set to sleep whenever I closed the lid. Well, now it does not want to.
    I installed a screensaver and used it for a little bit, and now uninstalled it.
    The problem is, ever since installing and selecting that screensaver my computer won't sleep when I close the lid.
    What is the process to restore this and get it so that it sleeps when I close the lid?
    Thanks in advance!

    Hey everyone,
    Until about 15 minutes ago I had my powerbook G4 set to sleep whenever I closed the lid. Well, now it does not want to.
    I installed a screensaver and used it for a little bit, and now uninstalled it.
    The problem is, ever since installing and selecting that screensaver my computer won't sleep when I close the lid.
    What is the process to restore this and get it so that it sleeps when I close the lid?
    Thanks in advance!

  • OS X Lion does not boot when my Time Machine disk is connected

    Everytime I boot or reboot my MacBook Pro I am stuck at the grey screen and OS X Lion will not boot. When I disconnect my Time Machine disk (external disk connected via usb) I suddenly get the loading screen and OS X Lion boots properly.
    Pretty anoying I think, does anyone have a solution for this problem?

    Have a look at the boot log messages, using Console.app (also with the "dmesg" command), and see if there's a clue there, or, set the boot process logging to "verbose" (i.e., using TinkerTool System) and find out what's really going on live at boot time.  (Also, do you have BootCamp setup, or any ofther bootable partitions?)
    Hope this helps.

  • Bue tooth is dead, and computer does not sleep when i close the screen now.

    OK
    This is a on going issue:
    1-I paid for apple care 4 days prior to the expiration of my one year agreement with purchase, they shipped it a day after it expired of course, and at first it rejected my serial number saying it was beyond the date,
    2-i contacted Apple, they fixed this and after calling them again they repeated the same thing, i can not down load techtool deluxe.
    3-However, i used iMac apple care kit to download the latest Techtool deluxe only to find out it is not Leopard Compatible,
    Apple did it again with a new OS, releasing it with no coverage leaving us all sitting around like PC geeks !
    Now after several incidents with blue-tooth on the phone with tech support, like been told i have to pay money if its the OS doing this instead of the hardware itself, i am a bit fed up here., blue-tooth is dead and my macbook does not sleep, i can even see iChat still on while the screen is closed!
    I no longer have confidence i the idea of going back to Tiger on this computer will fix a bad logic board as i read others with the similar BT problem.
    Can anyone advise what to do next please?

    used original dvds and found BT, LEOPARD bugs caused the BT problems.

  • HT1721 computer does not respond when connect to HDMI TV monitor

    macbook air does not reconize monitor from HDMI TV

    help in troubleshooting Macbook to Sony HDMI... I  HAVE had the miniport/ HDMI cable connection working - I just plugged it into both ports and it worked - i.e. No fussing with "settings". Now, after kids hooked up Wii game – computer to TV does not work…
    My <system preferences> -> Display -> detect displays does not register any connection [alert: the arrangement tab of Display preferences is hidden because you only have a singe display attached to this computer].
    Q? is it the computer that does not recognize hookup or is it the TV that does not recognize the hookup?
    I have done all the standard go online for answers: reboot both, turn off both, connect cable, check input to HDMI, reset PRAM,
    Still no success…
    Your suggestions …??

  • HP ProDesk 490 G1 MT does not boot when external "WD - My Book - 4 TB - USB 3.0" is connected

    I'm troubleshooting an HP ProDesk 490 G1 MT.
    Intel Core i7 - 4770 CPU @ 3.40 GHz GHz
    16.0 GB RAM
    Windows 7 Professional Service Pack 1 - 64 bit
    HDD 1 GB
    HP doe's not boot if any external hard disk drive is connected. All dimensions and all brands, USB 2.0 or USB 3.0
    PC don't boot even if I command from BIOS to boot via internal hard drive.
    It try, I see Windows is loading, but then i see the PC is searcing a boot system, a MAC address and then it is lost and alone until I disconnect the external hard-drive ...

    The fact is that I have four Acer (2 desktop, 1 nettop, 1 Netbook) and 1Notebook HP (2006/2007) that not have this issue.
    When I connected the first time this morning the external hd, my mouse Logitech M570, trackball - wireless, went crazy. I searched and found a solution on Logitech Website.
    More:
    I wrote:
    ... " ... All dimensions and all brands, USB 2.0 or USB 3.0 ... " ...
    But is too long on Verbatim, Toshiba, WD, Samsung, Freecom, Lacie, sites.
    But "Never say never again", I tried and the site WD is unavailable.
    On the other hand is a common issue on HPs, I  can see on this site.
    I'll try the solution at:
    http://h30434.www3.hp.com/t5/Desktop-Lockups-Freezes-Hangs/Pc-hangs-at-hp-boot-screen-with-external-...
    of "jako 1x4". It didn't work for "MrWoogy", but I have a USB 3.0 hd.
    Tank you for your doctrine and wise advise.

Maybe you are looking for