Computer not assigning IP to WRT54G

I just bought a Linksys WRT54G wireless yesterday, replacing my Linksys BEFSR41(wired). I went through the setup wizard and everything went smooth. It detected the router and everything, and I can log into the router page using 192.168.1.1. My problem is that I can't connect to the internet. My computer won't assign an IP address to the router. When I plug my old router back in , everything works fine. I tried resetting my cable modem, router, everything and it just won't work. I have 2 computers hooked up wired, and 1 laptop thats wireless. The laptop detects the router on the wireless network, and I can connect to it, I just can't connect to the internet on all 3 computers.
I'm using Comcast as my ISP.
Any suggestions?

Connect the computerto router ..... to the LAN port ... use another cable from router internet port to Modem .....
Access routers setup page ..... using http://192.168.1.1 ....you will see username & password ...leave username blank & in password use admin ....
Under setup .... look for "Mac address Clone" ...... sub-tab ..... click enable & click clone .....
Click save settings ....
Go to status tab .... look for Internet Ip address ....
Perform a power cycle & see if you are going online or not .....

Similar Messages

  • WRT54G Wireless Router Will Not Assign a Network Address

    A Linksys WRT54G router will not assign a network address when I access the router using a Linksys WPC600N wireless card. I have the same problem accessing the router with a TRENDnet TEW-621PC wireless adapter. Both wireless adapters are assigned network addresses when I use other wireless routers. Also, I have no problems being assigned a network address when I access the WRT54G router in question using an old 2WIRE 802.11b wireless card.
    I have tried "Repairing" the connection, I have used ipconfig to "release" and "renew" the connection. However, each attempt fails to have a DHCP address assigned.
    I am a visitor at the work location with the connection problem, the router works for others without any issues.
    Thanks

    Well in such case .... you can try few settings on the wireless adapter ....
    If you are using WLAN monitor .....
    Click start >> All programs >> Linksys wireless monitor >> Click on "Profile" >> Delete all profiles >> Click "New" >> Type in the wireless network name >> Click next >> Configure the rest of the wireless settings same as in the router ...
    At last point it shows .... all the configuration settings ...reconfirm that  >> Click on connect ot a network & reboot the computer ...
    After reboot see if it shows connected or not....
    You can also use Static Ip in the configuration ....

  • Fix that works for my itunes/my-computer not recognizing 5G 60GB Ipod

    Hi:
    For me this fixed all problems with my own PC at work (when others in building worked fine). Turns out I had some networked drives and did not realize there was a conflict even.
    Russ Jacobson
    It is from the following help area on apple:
    http://docs.info.apple.com/article.html?artnum=93499
    Strange iPod behavior when Windows confuses iPod with network drive
    If the drive letter after iPod ("E" in most cases) is mapped to a network drive, both Windows Explorer and iTunes may exhibit strange behavior in relation to the iPod.
    Symptom
    One or more of the following occurs:
    * iPod does not show up in iTunes or as disk in Windows Explorer.
    * iPod does not show up as disk in Windows Explorer (even though disk mode is enabled on the iPod).
    * iTunes and Windows Explorer report the wrong amount of available space on iPod.
    * No songs appear on the iPod after an apparently successful update from iTunes.
    * Music copied to mapped network drive instead of iPod.
    Products affected
    * iTunes for Windows
    * iPod (all models)
    * Microsoft Windows 2000
    * Microsoft Windows XP
    Solution
    This issue is documented in Microsoft Knowledge Base document 297694, "New Drive or Mapped Network Drive Not Available in Windows Explorer".
    Changing the drive letter of your network volume should resolve the issue. If you are unable to change the drive letter of the network volume because your programs depend on a specific drive letter, then you can use the following steps to change the drive letter of your iPod instead.
    1. Open the Control Panel.
    2. Double click on Administrative Tools. Note: If you don't see Administrative Tools, look at the left column in Control Panel for a link that says, "Switch to Classic View," and click it.
    3. Double click on Computer Management.
    4. In the left column, click on Disk Management.
    5. Locate the iPod and right click on it, then click Change Drive Letter and Paths.
    6. Click the Change button.
    7. Use the drop-down menu to select a new drive letter. Note: Make sure to choose a new drive letter that is not already assigned to a network drive. The drop-down menu will display all available letters that are not assigned to a physical drive. Drive letters that are assigned to a network volume will still be listed here. It is also a good idea to assign a drive letter other than a, b, c, or d, as these letters are usually reserved for other system drives.
    8. Click OK.
    9. Click Yes on the confirmation dialog.

    Have you updated iTunes with the absolute latest software?  If you have not in a long time, your iPad won't be recognized.

  • SD card detected but not assigned a device

    I have a Dell XPS 14 notebook which comes with a SD card slot. I plug in my SanDisk 8GB card from my camera and the following shows up in dmesg:
    [821605.639247] mmc1: cannot verify signal voltage switch
    [821605.750637] mmc1: new ultra high speed SDR50 SDHC card at address e624
    And that's it. The card is not assigned to any device. lsmod seems to indicate that I have the required modules loaded:
    ± % lsmod | egrep 'mmc|sdhci|sd'
    sd_mod 31361 3
    rtsx_pci_sdmmc 13911 0
    scsi_mod 132250 4 usb_storage,libata,sd_mod,sr_mod
    sdhci_pci 12604 0
    sdhci 28820 1 sdhci_pci
    mmc_core 95465 3 sdhci,rtsx_pci_sdmmc,sdhci_pci
    rtsx_pci 32305 2 rtsx_pci_ms,rtsx_pci_sdmmc
    lspci also shows the SD card controller:
    03:00.1 SD Host controller: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01)
    But fdisk -l just shows my hard drive
    ± % fdisk -l
    Disk /dev/sda: 465.8 GiB, 500107862016 bytes, 976773168 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    Disklabel type: gpt
    Disk identifier: 0FBC37E2-A97E-4040-996C-F290C0C9CF0A
    Device Start End Size Type
    /dev/sda1 2048 1050623 512M EFI System
    /dev/sda2 1050624 976773134 465.3G Linux filesystem
    Anything else I need to do to get the SD card assigned to a device so I can mount it.

    It's considered a removable drive.  I have a USB card reader that if I insert it after the computer has been booted it gives me a little trouble, but having it inserted on booting it wants to put the device in a different order.

  • WRVS4400N : DHCP not assigning IP addresses if WAN link is down

    Hello,
    With the latest firmware installed (the one suporting fixed IP based on MAC), I have one problem: the DHCP server is not assigning addresses when the WAN link is down. When it is up, it generally assign IP based on the configuration binding (MAC/IP). But it sometimes fail to do so. Before using the wrvs4400n I had no issues with DHCP wrt54G and other routers.
    Any hints ?
    Thanks.
    V.

    Hi there!
    Thanks for contacting the business support - other guys got the same problem.
    I'm now back on firmware version 1.00.16 and everything works fine.
    But the new features were nice to have!

  • When I start Internet Sharing /etc/bootpd.plist is not created and the other device is not assigned an IP address.

    Just like the tite says. I am investigating why my Macbook Pro (3,1) running Mountain Lion will not assign an IP address to a computer connected via Ethernet when Internet Sharing is turned on (laptop receiving WiFi connection, supposed to be sharing connection over ethernet). I tested using a relatives macbook and it worked just fine. It turns out my laptop is not creating the file: /etc/bootpd.plist when Internet Sharing is turned on.
    I have a console log here from when I start internet sharing:
    8/11/12 12:01:13.634 PM
    InternetSharing[724]
    objc[724]: Object 0x7f94c940ead0 of class __NSDictionaryM autoreleased with no pool in place - just leaking - break on objc_autoreleaseNoPool() to debug
    8/11/12 12:01:13.642 PM
    com.apple.InternetSharing[724]
    bind(bootps 67): Address already in use
    8/11/12 12:01:13.642 PM
    com.apple.InternetSharing[724]
    error creating internal interface for devname bridge0@0: Address already in use
    8/11/12 12:01:13.644 PM
    com.apple.InternetSharing[724]
    no bridge interface to service en0
    8/11/12 12:01:13.644 PM
    com.apple.InternetSharing[724]
    unable to create service for en0
    8/11/12 12:01:13.645 PM
    com.apple.InternetSharing[724]
    _MISStartServiceDHCPWithOptions "en0": Operation not supported by device
    8/11/12 12:01:13.645 PM
    com.apple.InternetSharing[724]
    *** no external service
    8/11/12 12:01:38.065 PM
    com.apple.InternetSharing[724]
    *** no external service
    Any help is appreciated!

    Solved it, at least temporarily:
    Investigate process binding port 67 with the following command:
    sudo lsof -i 67
    Close the offending process (in this case: bootps):
    sudo /bin/launchctl unload -w /System/Library/LaunchDaemons/bootps.plist
    Start internet sharing again from the system preferences panel

  • Siebel F9 : Activity not assigned to contact - Outlook 2010

    Hi,
    Our environment change for a new version of Outlook (from Outlook 2003 to Outlook 2010)
    In my tests with F9 fonctionnality, I have exactly the same issue as doc ID 1556458.1
    After sending email, activity is not assigned to contacts anymore.
    As I see in doc ID 1556458.1, I change in OFT file "Set oSession = CreateObject("MAPI.Session") to "Set oSession = CreateObject("CDO.Message") but have the same result.
    In log file, I see that parameter "Field: Email To Line" have the name of the contact instead of email...
    Here specifications of my environment:
    Siebel 8.1.1.10
    IE8
    Microsoft Exchange Server 2010 SP2
    Client MS Outlook 2010
    Thanks for your help.

    Hi and Welcome to the Community!
    Here is a KB that discusses that error:
    Article ID: KB31752 "Synchronization Error. An error has occurred during an attempt to update a device database record" appears during a wired address book synchronization with BlackBerry Desktop Software
    Article ID: KB32420 BlackBerry Desktop Software displays "An error has occurred during an attempt to update a device database record." during contact synchronization
    Hopefully it contains something useful! There also are multiple existing threads on this site that discuss that exact error...your review of those might prove useful, and a search of this site, using the error message, error code, or symptom, should reveal all applicable existing threads to you.
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Thinkpad 430u Windows 7 - Public Network - Wireless router is not assigning IP address

    Hello, 
    My computer knowledge is limited, but I have a chronic issue when attempting to connect to public wireless networks, ie a coffee shop: 
    When I attempt to connect, the laptop identifies the public network as an Unidentified Network and although it "connects" it says No Internet Access. Normally, when I connect, I would be prompted to selected Home, Work, Public and this does NOT happen.  In the Network and Sharing Center, under the heading "View your active Networks" it says Unidentified Netowork, Public Network; Access type: No Internet Access, Connections: Wireless Network Connection (name of network).  The words "Public Network" is NOT a hyperlink and cannot be clicked on.   
    When I run run cmd and check ipconfig I find that the wireless router is not assigning an ip address to my laptop.  i then input ipconfig/releasei, and ipconfig/renew.  I then receive and error saying "An error occurred while renewing interface Wireless Network Connection: The operation was canceled by the user." 
    I have turned off my firewall.  
    My smart phone can connect the the internet with no problem and the other laptop users have no problem either.  This indicates there is no problem with the wirless router itself, but is some kind of setting or something that needs to be adjusted on my end.  
    Autoconfiguration IPv4 Address: 169.254.86.100
    Subnet mask: 255.255.0.0
    Default gateway: n/a 
    Please, any help is appreciate.  This is a chronic problem any time I link to public networks.
    P.S. I have no problem connecting to the internet in my own home
    Thank you!! 

    Sorry, forgot to include: it's a 2Wire 2701hg-b Residential Gateway.  I'm unsure how old the model itself is--it was just given to us by AT&T (it's the model they use for their U-verse service).  I checked today and the firmware is up-to-date. 
    Thanks.

  • In our enterprise MPLS network we are using 192.168.20.0/24 subnet, in this subnet we have not assigned the IP 192.168.20.200/30 & 204/30, But still these subnets are reachable . Are these NNI IP ...Please explain.

    In our enterprise MPLS network we are using 192.168.20.0/24 subnet, in this subnet we have not assigned the IP 192.168.20.200/30 & 204/30, But still these subnets are reachable . Are these NNI IP ...Please explain.

    I have checked with ISP, there response is like below:
    Those are the NNI to GBNET IPs for Dominican Republic. They are Network IPs. You should be able to ping them-that means they are working.
    WANRT01#show  ip route | include 192.168.20.20
    B        192.168.20.200/30 [20/0] via 192.168.20.226, 02:18:29
    B        192.168.20.204/30 [20/0] via 192.168.20.226, 02:18:29
    Here its shows from any of our MPLS site we are able to trace the IP and it seems like, 192.168.20.204/30 is one more site but in actual its not.
    INMUMWANRT01#ping 192.168.20.205
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 192.168.20.205, timeout is 2 seconds:
    Success rate is 100 percent (5/5), round-trip min/avg/max = 224/232/260 ms
    INMUMWANRT01#trace              
    INMUMWANRT01#traceroute 192.168.20.205
    Type escape sequence to abort.
    Tracing the route to 192.168.20.205
    VRF info: (vrf in name/id, vrf out name/id)
      1 192.168.20.226 24 msec 24 msec 24 msec
      2 192.168.20.206 [AS 8035] 232 msec 232 msec 252 msec
      3 192.168.20.205 [AS 8035] 224 msec 224 msec *

  • I have Win 7 64bit and the computer "not responding" often.

    The event logs show that Bonjour is the biggest problem in system failures and the computer Not Responding.  Is there a fix for Bonjour or is there a way to run itunes without it?
    If itunes is not compatible for windows 7 Does apple have something else to use for media?

    Hello AEC396
    It sounds like you are trying to burn a playlist to a disc in iTunes, but you are getting an errorabout missing drivers.  I found a couple of resources that I think might help with an error like this.
    I recommend starting with the steps in this article:
    iTunes for Windows: Optical drive is no longer recognized, or "Disc burner or software not found" alert after install
    http://support.apple.com/kb/TS2308
    If you are still having trouble with burning a disc after following the steps in that article, I recommend following the steps in this article:
    iTunes for Windows: Additional troubleshooting tips for burning issues
    http://support.apple.com/kb/TS1374
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • HT204053 why are not all my songs I have purchased in the itunes store and are on my computer not on my phone?

    why are not all my songs I have purchased in the itunes store and are on my computer not on my phone?  Very frustrating I purchaed almosta $100 worth of songs for a trip and they are not on my phone after continuious syncs.  Do I have to pay for itunes match for this?

    Welcome to the Apple Community.
    Have you actually selected them to be synced to your device from the iTunes sync settings.

  • Error while trying to run Bex Query -------- Field symbol is not assigned.

    Hello Every body,
    I am facing the following error after giving some value in Selection screen and trying to run the Bex Query
    ERROR : Field symbol is not assigned.
    Thanks in advance,
    Praveen

    can u plz give details of variables, what it is build on and the value u r inputing,
    also is thr any dump.
    double click on the error message it shows u. it will give u the detailed error message. post that too

  • Reporting Issue   "Opening Balance values are going to Not Assigned Values"

    Hi Friends,
    Closing Balance values are perfectly showing but opening balance values are going to Not Assingned Values? I am not able to find it out.
    our query is built on PCA Daily Multiprovider.
    Pls Help.
    Thanks
    Asim

    Hi Ravish,
    Here are the details
    Stock values and quantities in the PCA cube of BW never show correctly at an article level due to an opening balance issue.  This reduces our ability to report on stocks at moving average price, i.e. anything that actually matches the financial values in the system. The issue arises because stock at the beginning of the year (quantity and value) for any site is only shown against an article of "Not assigned."  Stock movements during the year are shown against the appropriate article.(If you have a new site, the will have stock assigned against an article up until 31 December and then the 31 December values are shown against "not assigned" for the next year).
    Thanks
    Asim

  • How to pass # (Not Assigned) in open doc url ??

    I am unable to pass # (Not Assigned) in open doc URL. I am also try %23 ( encoded form of #) but it show MDX error and when i supply directly # then my WebI report pull all the data i.e. my filter doesn't work. Please give me some way to pass # in opendoc..

    http://boseimdev60:8080/OpenDocument/opendoc/openDocument.jsp?iDocID=AQgEkeXDfo5PpR_IFC.rse0&sIDType=CUID&sType=wid&sRefresh=Y&mode=full&sRefresh=Y&lsSCalendarYear%2fMonthTo=032010&lsSCalendarYear%2fMonthFrom=032010&lsSInfoprovider (Multiple Required)=ZPUR_C15&lsSPlant(SelectionOptions%2cOptional)From=&lsSPlant(SelectionOptions%2cOptional)To=&lsSPur Doc Category (Optional)=K&lsSPlant=%23
    Here Plant=%23 i.e. in last i increase this prompt in WebI level so its work.

  • Showing as not assigned

    Hi All,
    In the bex analyzer report, I am seeing values as NOT ASSIGNED and #  in text and key columns when there is no data.
    I want to see them as blank instead of them,
    Can anyone tell where can I make that setting or change.
    Thanks In advance!

    Hi Pallavi,
    I think you can find some VB macro code posted here that will help you to do this...there is no option set in the query designer to blank out the records.
    Hope this helps...

Maybe you are looking for