Computer speakers hooked up to a tv?

I havea sony bravia kdl 40ex400 and i am thinking about getting the logitech z323 computer speakers and i was wondering if i can hook them up to my sony? if so what do i need to be able to do that?

Muyara wrote:
I havea sony bravia kdl 40ex400 and i am thinking about getting the logitech z323 computer speakers and i was wondering if i can hook them up to my sony? if so what do i need to be able to do that?
We have Logitech speakers like this hooked up to our 24" Kitchen TV. They're better than the TV, but no better than adequate for the kitchen/dining area. You'll see a bit more bass, but other than that not much difference over the Sony.
If you need better sound and you don't want a full surround system, look at some of the cheaper soundbar+subwoofer combos that are available.

Similar Messages

  • Connecting TV and Computer Speakers at the same t

    Hi,
    I have a SB Li've Value and I wanted to connect my regular computer speakers as well as my TV to it.
    I am using a mono plug to hook my computer speakers and my TV currently. Whenever I want output on my TV I have to unhook my computer speakers from the soundcard and plug in the mono plug from the TV.
    Is there any possible that I do not have to do that and I can get output on both using the mono plugs.
    Please help me out as I have looked al over the place and I cannot find an answer to this problem.

    Get an /8" stereo Y splitter (single male, split side females)

  • Sound works with headphones but not with computer speakers

    I've got an iPhone 3GS and an iPad. A few weeks ago I setup an older pair of computer speakers in my living room and I've been using that as a bookshelf stereo. I just plug in whatever device happens to be around, the phone or iPad to drive the music.
    Tonight though, the iPhone will not output any sound to the computer speakers. It will play music through the external speakers without any issue - same for the iPod headphones. Originally I chalked this up to an issue with my speakers, but when I hook the ipad up to them, I get sound.
    Any ideas as to what this could be? The phone worked fine until tonight and I've tried to restart the phone and turn it off.

    Hey polofson,
    Thanks for the question. I understand you are experiencing issues with Siri in relation to your microphone. On the iPhone 5, Siri utilizes both the mic in the receiver opening and the mic near the rear camera. You may want to make sure these are not blocked (commonly by third-party cases):
    iOS: Troubleshooting Siri
    http://support.apple.com/kb/TS4079
    Ensure that Siri can clearly hear you
    If Siri is unable to clearly understand what you are saying, make sure your microphones are not blocked.
    iPhone 4s
    Verify that the bottom microphone, located to the left of the dock connector, is not blocked.
    iPhone 5
    Verify that both the mic in the receiver opening and the mic near the rear camera are not blocked.
    iPod touch (5th generation)
    Verify that the mic near the rear camera is not blocked.
    iPad (3rd generation)
    Verify that the mic at the top center, above the FaceTime camera, is not blocked.
    All models
    - If you are using a protective case, try removing it.
    - Try turning your device off and then on again.
    Thanks,
    Matt M.

  • How do I set upmy Imac to allow using both my computer speakers and a Bose SoundLink system as outputs at the same time.  I can use one or the other, but not both.

    how do I set up my Imac to allow using both my computer speakers and a Bose SoundLink system as outputs at the same time.  I can use one or the other, but not both.  From systems Preferences I must select one or the other.  I want both to work all the time.

    Hi,
    I would recommend you to use 0FI_AP_4 rather using both, particularly for many reasons -
    1. DS: 0FI_AP_4  replaces DataSource 0FI_AP_3 and still uses the same extraction structure. For more details refer to the OSS note 410797.
    2. You can run the 0FI_AP_4 independent of any other FI datasources like 0FI_AR_4 and 0FI_GL_4 or even 0FI_GL_14. For more details refer to the OSS note: 551044.
    3. Map the 0FI_AP_4 to DSO: 0FIAP_O03 (or create a Z one as per your requirement).
    4. Load the same to a InfoCube (0FIAP_C03).
    Hope this helps.
    Thanks.
    Nazeer

  • How do I use GarageBand as a amp/speaker to listen to my Electronic Drum set? I have a MIDI-USB cord already but I can't figure out how to listen to my set through the software using my computer speakers?

    How do I use GarageBand as a amp/speaker to listen to my Electronic Drum set? I have a MIDI-USB cord already but I can't figure out how to listen to my set through the software using my computer speakers?

    If you want to listen to the sounds of your drum set, you should use an audio cable and connect it to the computer's line-in, then create a real instrument track.
    If you use a Midi/USB interface, you'll have to create a software instrument track and select one of GB's drumsets as the instrument. Hopefully your drumset's midi notes are mapped to the right sounds in GB.

  • How can I play my iPod songs to my computer speakers (Windows 7 32-Bit with the newest version of iTunes)

    I have an iPod touch 4th generation, an Apple TV and a Windows 7 Home Premium PC. I can play songs from my iPod touch to the Apple TV and from the computer to the Apple TV, but how can I play songs from my iPod touch to my computer speakers?

    Step 1 – Open the Terminal.app
    Either by start typing Terminal on the Spotlight, or by going into Applications -> Utilities -> Terminal.
    Step 2 – Open the hosts file
    Open the hosts by typing on the Terminal that you have just opened:
    view source
    print?
    1
    $ sudo nano /private/etc/hosts
    Type your user password when prompted.
    Step 3 – Edit the hosts file
    By deleting
    #74.208.10.249 gs.apple.com
    #127.0.0.1 gs.apple.com
    from your hosts file, save close and then reboot.
    Or in Windows:
    Navigate to C:\Windows\System32\drivers\etc, open hosts file in notepad and remove
    #74.208.10.249 gs.apple.com
    #127.0.0.1 gs.apple.com
    Save it and then reboot.

  • How do I listen to the songs on my iPod through  computer speakers?

    Ok. I give up.
    I don't understand how this iPod Shuffle works.
    I got it a few months ago, and copied three or four Brian Eno albums onto it (46 songs to be exact).
    I can listen to the songs on the iPod when I am using it with the earphones, but when I plug it into the computer, it says something about "some of the items in the library were not copied to the iPod because they could not be found." (Meaning none of the songs were copied.)
    I don't understand what it's trying to do.
    The songs were already on the iPod. Why is it trying to "copy" them on to it?
    And if I unplug the iPod from the computer and play it through the headphones, the songs are still there.
    Could somebody please help me?
    I just want to be able to listen to the songs that are on my iPod through my computer speakers. How on earth do I do that?!!

    I have the syncing option unchecked, that is why I do not understand why it is trying to sync.
    I am also trying to play songs off my iPod via iTunes.
    I also don't understand why I need to have the same songs on my PC if they are on the Shuffle. My songs are on my external hard drive... which I don't always have turned on, or with me for that matter. I certainly don't want to be hauling a hard drive around with me wherever I travel to. I want to be able to copy a small number of my favourite songs onto the Shuffle so I can carry the Shuffle and the laptop around with me and listen to them.
    I need to be portable!!!

  • Why is my bluetooth speaker connected but sound only comes out of the computer speakers?

    My bluetooth speaker (JBL Charge 2) is shown as "connected in the blu tooth section of the task bar. I have also gone to system preferences and the speakers are also shown to be connected and chosen as the main speakers. However, no sound comes out of the bluetooth speaker but rather the sounds still comes out of the computer. speakers. I have tried connecting, reconnecting, and restarting computer. The bluetooth speaker is also shown as connected in bluetooth preferences. What is wrong?

    I have tried to connect and Jambox and have the same problem; bluetooth speakers are connected and chosen but sound comes out of computer speakers.

  • How can I switch on my Apple TV speakers when it asks "multiple speakers" I cannot switch off my computer speakers and switch on my Apple TV speakers so cannot get airplay to work?

    How can I get my Apple TV airplay to work from my PC.  On the airplay symbol it says Multiple Peakers please choose but I cannot switch off my computer speakers and switch on my Apple TV speakers so cannot get airplay to work from my PC.  Everything is OK when using my Ipod touch.

    Don't use Multiple Speakers option and just choose the AppleTV
    What are you trying to Airplay? If it's iTunes content it's simpler to 'pull' the stream from the Computers icson on AppleTV by selecting the libarry and media.
    If you are attempting to Airplay the desktop you can't.

  • I blew my motherboard on an old computer and hooked my old hard drive to the new computer and want to transfer my bookmarks to the new drive but cannot find where they are located on the old drive--any help?

    My motherboard went bad on my old computer, but the hard drive was OK. I purchased a new computer and hooked my old hard drive to it through a usb adapter. I would like to import or copy my bookmarks from the old hard drive to my new one, but I cannot find where they are. I was unable to determine this from searching articles on the web. Be advised that my old hard drive is basically nothing but a storage place for files at this point. My old operating system was windows XP, and my new system is Windows Home Premium.

    https://support.mozilla.com/en-US/kb/Recovering+important+data+from+an+old+profile
    Your old Profile is located here in Win XP and W2K: <br />
    ''drive'':\Documents and Settings\''Windows login user name''\Application Data\Mozilla\Firefox\Profiles\''profile_name''

  • Can't get Bose computer speakers to work with my Mac pro lion

    I have just bought the Bose Companion 11 computer speakers for my Mac Book Pro. They are set up correctly (in the headphone jack) and they play my itunes music beautifully. However, when they are plugged in I get no sound from internet videos, etc. I have to take the plug out of my headphones jack and then I get the sound from my computer but not the speakers. Can anyone help ..I don't know what I am doing wrong...or how to get the Bose speakers to work with all my computer (internet content). I looked at system preferences and the Output says headphone port but the input says internal microphone (built-in).
    Please help.
    Thank You,
    Karen

    Don't worry about offending me...I am, admittedly, no computer whiz! I have had speakers before....but I took these in to Best Buy...with my computer (Where I bought them) and the "Geek" person plugged them in and they worked.
    What we did notice was that the jack that goes into the plug just below the left speaker plug was loose. So I brought it home and it worked! Then tonight I turned on my computer and no speaker input, so I checked the back of the right speaker and that plug (if that is the right name?) had fallen out...so re-connected it and they work! So, I guess I may have to tape that plug in ...or what do you suggest??...so it doesn't keep falling out.
    Thanks so much for answering me.
    Karen

  • Connect apple tv to computer speakers.

    Hello,
    What can I use to connect the apple tv to computer speakers? I know it has digital output but speakers only have 3.5 m jack input.
    Is there any cable that will make this possible?

    See https://discussions.apple.com/message/18084600#18084600. In other words, the answer appears to be no unless you're willing to live with some serious compromises.

  • How do I output Audio through computer speakers while outputting video via Firewire to TV

    I'm outputting the video and audio streams via a FireWire connected Camcorder to a TV display (used as a third display), but I want the audio to output through the computer speakers and not through the Camcorder speakers as is happening.  If I disconnect the Camcorder, the audio outputs through the computer speakers normally.  This must be an audio out setting issue but I can't remember which settings to adjust.  I used to do this in an earlier version of PRE but I've forgotten the settings.  I'm using PRE 9.0.  If someone can understand what I'm trying to say, I hope that person can help me.  Thanks.

    Good thought.  I was thinking the same way, and I tried  adjusting every
    setting that's there but without any luck. It must be  a setting within PRE
    that would allow the video output stream to be split from  the audio output
    stream but I just can't find the setting.  As I mentioned  in the posting, I
    used to do this in an earlier version of PRE.
    M Martineau
    In a message dated 6/3/2011 5:02:55 P.M. Pacific Daylight Time, 
    [email protected] writes:
    Interesting question.
    Not sure that the answer will be  there, but I would go to Edit
    Preferences>Audio Hardware, and look very  closely at the settings there.
    Good luck, and hope that it's just  the matter of a  setting?
    Hunt

  • Is it OK to connect the i-pod to the computer speakers???

    Can anyone tell me if it is alright to connect my 5th generation i-pod to the computer speakers as I don't have a sound system.My friend connected his i-pod mini to the PC speakers and it seems though as if it has damaged his earphones.
    IBM   Windows XP   I-pod video,I-pod mini

    i've tried connecting a shuffle to amp. it goes well...but if your computer speakers rely from the ipods's power supply i guess the sound would be at low volume or your ipod's battery would drain fast...

  • Connecting 5G Ipod to Computer Speakers

    I have a 5G Ipod, and my computer speakers have a USB Port on the external Volume Controls. I wanted to know if i could use my Computer Jack to connect my Ipod to that USB hub and to have it play through the speakers. These are my speakers
    http://www.creative.com/products/product.asp?category=4&subcategory=27&product=4 912&nav=1
    Please get back to me

    well i tried it but i dont see how i would do it. is there a setting on the ipod to send the audio feed out of the bottom port? not quite sure. I played the music like i normally would and could only hear it out of the earbuds.

Maybe you are looking for

  • MacBook and Mac mini togheter?

    Hi everyone... I'm the proud owner of a MacBook but I'm studying Computer Engeneering and my MacBook is becoming slower and slower.. So my question is if I'm able to use Mac mini conected to my MacBook using it as a screen. Thanks for your answer!!

  • IPod Nano would not connect to Windows or Format. *SOLVED*

    Ok, first post and I am just posting to thank those who have posted some different things to try, thanks to you guys, I have a working iPod Nano. Here is what I tried... The Problem iTunes would not see my nano and could not format the nano during in

  • Any tips for debugging apply handlers? How to use SYS.AnyData

    Well, I'm setting up my first stream. I've set up a simple stream just to understand the concepts, but now I need to start the real work. I've written an apply handler that takes the LCR, turns pulls values from the sys.AnyData, and uses them in anot

  • Problem in the load, all data skipped

    Hello,I have a problem when I load data, the message (WARNING) is:"Aggregate storage applications ignore update to derived cells. [209774] cells skipped"All my data are skipped, and this is the only message I have, I do not have any errors in my *.er

  • How To Get Adobe Flash Movie To Work On Another Compter?

    Somebody please please help me. I use a English language Windows operating system, forgive me. I made an interactive book in Adobe Indesign CS 5. The content, which are all graphics, was all originally created in Adobe Illustrator CS5, but I exported