Computer to Wireless Controller
Hello,
I am trying to build a test lab to test Radius athentication for my Wireless Controller.
The question is: Can I plug my WC into a basic Cisco home router and browse to it?
I have tried putting the WC on the same subnet, the gateway is the same, but I can not browse to the device.
I am plugged into the management port and that port is the one that I have configured.
Any help would be great.
Thank you,
Jim
It is feasible. If you can "ping" the WLC, then you should be good. Now, if you are "plugged in to the management port" directly with your laptop, then you need to make sure
1. The WLC Management interface is not "tagged"
2. Your client NIC is 1000 full capable (set to 1000/Full) as the WLC will not "negotiate" anything else.
Also, you need to make sure your interface/switchport config are matching in terms of VLAN tagging/Native VLAN if you are plugging it in to you Cisco home router. I'm not sure if you're talking about SB or Enterprise device, or a "Linksys" Cisco product. If you "can't configure VLANS", then make sure your WLC management interface is "untagged".
From "console" access, you can issue...
(Cisco Controller) >config interface vlan management 0
Similar Messages
-
Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9 (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number : 73-14034-04
PCA Assembly Number : 800-34273-05
PCA Revision Number : A0
PCB Serial Number : FOC16075VZ3
Top Assembly Part Number : 800-34284-03
Top Assembly Serial Number : FCZ1611W414
Top Revision Number : A0
Product/Model Number : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
ap-manager 2 untagged 209.165.200.231 Dynamic Yes No
management 1 untagged 209.165.200.230 Static Yes No
service-port N/A N/A 192.168.1.157 Static No No
virtual N/A N/A 1.1.1.1 Static No No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, GraciasHi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 management Disabled
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast
IP Status
c4:64:13:8f:93:40 209.165.200.230 hosp 0.0.0.0
Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address Port State Tout
Authorization Servers
Idx Server Address Port State Tout
Accounting Servers
Idx Server Address Port State Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
Primary ..................................... Local DB
Timer:
Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
EAP-FAST:
Server key ................................
TTL for the PAC ........................... 10
Anonymous provision allowed ............... Yes
Authority ID .............................. 436973636f00000000000000000000
00
Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network Netmask Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11bg :
Channels : 1 1 1 1 1
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address Classification # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID State # APs Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address State # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name State Type Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established -
Cisco Aironet 3502i and Virtual Wireless Controller- Question
Hello everyone,
As soon, I purchased two Cisco 3502i and Cisco 1142 however, two issue are that I don't have controller and smartnet. As my purpose, it using for Home Use but house with 2,500 Sq ft with two floor and new 24x24ft garage with two floor. I put two Cisco 3502i for garage and one cisco 1142 in house on second floor. Separated for multi media, gaming, streaming high resolution video, parts, and downloads programmings online. It will run with Cisco Catalyst Express 500 with 24 ports (4 POE) and two gigabit ports. In house, it have Dell Poweredge 2850, Cisco Catalyst Express 500 with 24 ports POE and 2 ports gigabit.
I thought to make my own developing with my first time using Wireless Controller. I wanted to try out with Virtual WLC on Dell Poweredge 2850 running ESXi 4.1.
Specs for Dell Poweredge 2850:
- 2x Intel Xeon Dual Core 3.8 GHz
- 4GB RAM (Will upgrade to 12GB soon)
- 2x 146GB and 2x 36GB SCSI
- 2x 1 Gbps built in and 4x 1 Gbps PCI-X
Developing with Untangle and pfSense to make it support with LADP and VLAN to both Cisco Express 500 using 4 gbps PCI-X. I have read the requipment list to use Virtual WLC but it seem met the requipment for my 2850. If someone offer me to get Virtual WLC and IOS from their, I accept to "borrow" it. I do go college which is Rochester Institute of Technology at New York and my major is Applied Computer Technology. I live here at Hampton Road, Virginia. Just in case if you might know about RIT. I just start to learning myself with Cisco books.
I have a question:
- Is there possible to get trial or full version of Virtual WLC?
- Is there possible to get Lightweight or Autonomous IOS for Cisco 1142 and 3502i?
- Does it supported Dell PowerEdge 2850?
- Does 3502i support Autonomous? (Not actually but I have researched around online about that it will work with 1262's IOS)
Thanks
GageAnswers in-line...
I have a question:
- Is there possible to get trial or full version of Virtual WLC?
No. You will need a SmartNet contract (or a freshly purchased device) to obtain software from cisco. Nobody will provide this to you.
- Is there possible to get Lightweight or Autonomous IOS for Cisco 1142 and 3502i?
No. You will need a SmartNet contract (or a freshly purchased device) to obtain software from cisco.
Nobody will provide this to you.
- Does it supported Dell PowerEdge 2850?
Cisco doesn't go in to great detail regarding the actual Hardware requirements of the vWLC (as far as ESX Host requirements). Primarily, making sure you are running ESX 4.x/5.x is necessary. The vWLC provisions 2Gb of RAM and 8GB of thick provisioned storage, so if your host can accomodate I don't see any reason it wouldn't work.
- Does 3502i support Autonomous? (Not actually but I have researched around online about that it will work with 1262's IOS)
Yes, with the latest versions of IOS 15.2(2)JB, full functionality in autonomous can be achieved on the 1550, 3500, and 3600 series APs
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/15.2_2_JB.html#wp355587 -
How do I configure the 2504 Wireless controller with AP?
I recently purchase the 2504 wireless controller and the 1602i AP. I was able to do the basic setup of the controller and can now access the web interface, but the AP is not being detected and I am unable to add it.
First of all: 1602 AP need minimum software version on WLC: 7.4.100.0
paste this info:
sh sysinfo from WLC
sh version from AP.
Did you create a DHCP pool for APs to get IP ?
Try to to be keep AP and WLC on same subnet.
regards -
I am unable to stream Netflix to my Iphone or Apple TV, from my wireless router . . . even though I am able to watch Netflix on my WII (also wireless) and desktop computer (not wireless).
On the Iphone and Apple TV I can connect to Netflix . . . it recognizes me and my account settings . . . and I can veiw all my recent programs and show titles, descriptions, etc.. But when I select one to watch I get a message saying:
"ERROR A PROBLEM OCCURED WHILE PLAYING THIS ITEM. TRY AGAIN LATER, OR SELECT A DIFFERENT ITEM. GO TO WWW.NETFLIX.COM/SUPPORT FOR MORE INFORMATION. (139)
Netflix support say there is nothing wrong on their end . . . that it is an Apple issue. They see the request for the show, the devices are registered . . . but it shows 0 bandwidth to the device.
My Apple TV did this when I first hooked it up a couple of weeks ago. Then after a few days started working with Netflix, for no apparent change . . . now doesn't again for the past couple of days (I think that it auto restarted the other night after a virus scan).
Very frustrating, and driving me nuts! Has anyone else had and been able to resolve this problem?Troubleshooting
Apple TV2 update one day and netflix is browsing but not launching the actual content (error 139)
Ipad2 (another ios device) forces me to update netflix if I want to use it and I get the same error 139 on it.
**** now I have two not ways not working where prior to some update it was fine.
Nintendo Wii is still working ( mind you running an ancient version of netflix ) Dusted the Wii off and gave it to the kids use. Now they are happy again...
PC is also still working ( using some other flash client ) but that's just of interest, we're not going to be watching tv with that.
My wife's iphone 4s is still working. Odd.. still ios but for somereason I am not forced to update the version. So basically she could mirror stream up to the apple tv with it. Nice feature of Ios5. Later found out it is using 1.4 version of netflix. The most useful thing out of that is that all 3 of the devices are Ios and it was actually the iphone with the 1.4 version of netflix that still worked!
I heard from a friend who was on a different ISP he was still working so I took my appletv2 and ipad2 over to my brothers house who is on that same ISP as my friend and both started working. So the ISP is involved too!
Brought the appletv2 and ipad2 back to my house hoping it would maybe still work. No dice Broken again.
Searched the appstore for a decent packet analyzer and there isn't really anything. I was able to sniff the traffic with my PC and also on my juniper ssg5 confirmed that. Turns out port 80 traffic is actually failing and authorization is not happening. The other clients do not do this...
Asked a buddy from work who used to work at the ISP if he could make a call to some one who might actually know what is going on. He came back pretty quick and said yea they are trying really hard to get the beta patch in from Bluecoat asap.
So knowing that it was actually Netflix that changed when it hit 2.0 and in my case the ISP made the adjustment it's pretty safe to say this issue is going to be ongoing unless netflix changes again the way they authorize for licenses.
So that's the summary of what went right down the troubleshooting path but I'll tell what what didn't
2 calls to Netflix (useless... waste of time... they are too quick to blame anyone but themselves)
1 call to apple support (support call was going to cost more than it cost for me to change ISPs)
2 calls to ISP (through the normal means - regular support number)
So why is this intermittantly working sometimes? If you are lucky enough to authorize to an IP address that is not cached they voila you are going to get an authorization / a license to watch the show. Some people report after defribulating their appletv (reseting, rebooting, dns changes, you name it) they get it working. Over the past month we all seem to have got it working for some period of time only to lose it a day to two later.
It's now been several days since the beta patch to the bluecoat and 4 of us who have been communicating on the issue appear to be online all at the same time for those several days and that is a good sign that we might be out of the woods on the issue.
Hope this turns into something helpful for someone else out there. -
I cannot get my IPad2 to print (it cannot find the printer) using a Laserjet CP1525nw color printer across a wireless network using a Cisco 1508 Wireless Controller with 49 wireless access points. HELP!!!!
What is the secret to getting Bonjour to work on it?
I can get the IPad2 to locate the HP CP1525nw printer without a hitch using a low budget Netgear WAG102 stand alone wireless access point on the same network.If it helps somebody, here is what you need to do.
It worked for me, but only in Multicast-Unicast mode.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0 080bb1d7c.shtml -
Error in GUI of Cisco 3850 Switch with Wireless Controller.
Hi,
I have Configured 3850 switch wireless controller. But while accessing the controller through GUI, I faced following errors while configuring it through GUI.
Because its complecated to configure it through CLI.
Attached are the snaps of error faced.
and if I didnt get this error, and able to configure, I can save it because of this error.
Please help me on this issue, so that I can easily configure the controller.
Brgds,
Ninad ThakareHi Sandeep,
Here is the configuration which I have did.
ip http server
ip http secure-server
wsma agent exec
profile httplistener
profile httpslistener
wsma agent config
profile httplistener
profile httpslistener
wsma agent filesys
profile httplistener
profile httpslistener
wsma agent notify
profile httplistener
profile httpslistener
wsma profile listener httplistener
transport http
wsma profile listener httpslistener
transport https
wireless mobility controller
wireless management interface Vlan4 ( Voice VLAN )
wlan FG-WiFi 1 FG-WiFi
client vlan 4
ip dhcp server 10.106.72.1
no security wpa akm dot1x
security wpa akm psk set-key ascii 0 testing1234
no security wpa wpa2
no security wpa wpa2 ciphers aes
no wmm
no shutdown
wlan GLOBALACCESSII 2 GLOBALACCESSII
client vlan 4
ip dhcp server 10.106.72.1
no security wpa akm dot1x
security wpa akm psk set-key ascii 0 testing1234
no security wpa wpa2
no security wpa wpa2 ciphers aes
no wmm
no shutdown
ap group default-group
ap group 3850WLC
wlan FG-WiFi
vlan 4
wlan GLOBALACCESSII
vlan 4
end
Brgds,
Ninad Thakare -
I use the Airport Extreme modem for my computer and wireless devices. I can't access my iphone 4 and 4S. It does not accept my passcode. My wireless laptop and wireless tower computer does accept the password. Can you help me?
You really have an iPhone question here.
Start with the Troubleshooting Guide for iOS devices:
http://support.apple.com/kb/TS1398
Post in the correct iPhone support area if you need more assistance.
Using iPhone -
Managing remote C800 with the wireless controller
We have a number of regional offices throughout the country with a C800 as the Internet facing router and it is also our wireless.
We have a Cisco wireless controller in the Data Center an we need to manage\monitor all the C800, but the problem is that those remote sites
are not VPN'd nor part of our WAN network.
Which setup do you
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
recommend:
1) 1) WLC to monitor the C800 using its public IP address
1) 2) Create a VPN tunnel from each of the remote sites to our data center and only allow wireless to go through for mgmt purposes
anany other options?
TFirst question is which 800 do you have ? there's like 20 different versions out there.
If you talk about WLC, I would suppose you have something like the 880 ?
I'm afraid the WLC will need the internal AP ip address. So you would need to do so reverse nat to direct public ip address tarffic on capwap ports to the internal AP.
This or the VPN tunnel.
Nicolas
===
Don't forget to rate answers that you find useful -
How to change IP adress of wireless controller 2504 . from GUI
how to change IP adress of wireless controller 2504 . from GUI
In the existing setup, does WLC management & APs are on the same vlan ? If that is the case you may have not configured any of the below, as AP L3 broadcast reach WLC & in that way AP will learn about WLC.
If WLC & APs are on different vlan you may already use one of WLC discovery method listed below.
1. DHCP Option 43
2. DNS
3. UDP broadcast forwarding
4. Static configuration
When you change the WLC management IP address, AP need to know what is the new IP & you can modify the configuration of the method you used.
HTH
Rasika
**** Pls rate all useful responses **** -
Syslog on Cisco Wireless Controller
Hi everyone
I have question about syslog on wireless controller. I need to know what is information in the syslog from controller. I had read paper in the community some siad it has not much in the syslog but it has not detial what is the information in the syslog sent. I know that almost information such as client, authentication, and much benefit logging in the SNMP. So, anyone have any idea or information please give me the idea or information.
Thanks
VYou just need to setup the sylog and try different logging levels to see if it gives you the information you need. YOu might not get what you want or if you find a syslog level that gives you the info you want, you might get a lot of stuff you don't want to see.
http://www.cisco.com/en/US/products/ps6307/products_configuration_example09186a00809a2d76.shtml
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Problems between a Wireless Controller and a Switch.
I have a Wireless Controller 4402 connected to one sw2960G.
I configured the controller with LAG and the switch (sw2960G) with etherchanel.
I connected the controller 2 distribution ports to the 2 ports of the switch (configured with etherchanel).
It worked like it should work.
But the problem is like this: if I take one cable that is connected to the switch and unplugged that cable from the switch (if that cable is the one connected to controllers port one) I have connectivity between both machines.
If I plug in the switch the cable connected to controller port one and take the other cable and unplugged that cable from the switch I stop the connectivity between the two machines.
I think that was not supposed to happen⦠because the LAG in the controller should put every AP in the second controller's port, and the connectivity between the machines should not end.
Can any one help me?
Can any one tell me what I am doing wrong?
Thanks in advance,
RuiWith LAG enabled in the controller I think I can have only one ap-manager interface.
The LAG will (it is supposed to) do the load balance automatically.
I mean, if one of the interfaces is âdownâ the other will have to coupe with all the AP's.
I should have always connection between the controller and the switch.
The STP of the controller is configured by default (STP Mode = OFF).
In the case of etherchannel load balance⦠I saw the Cisco documentation and I did not saw any thing about that. I think that The LAG as to do that for the controller⦠I'm right about that?
I will see the link that you advisedâ¦
Can you help me?
Thanks,
Rui -
Manually add Access Point to 2504 Wireless Controller
We have a 2504 Wireless Controller and it works great!
We currently have 6 Access Points (Aironet 1252) connected.
We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.
Now, I have been assigned to add another Access Point, but at a remote site.
The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.
We have plenty of licences on our current Wireless Controller.
Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
If so, how?
Thank you!
Bryan SmithHere are some links
AP join
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
FlexConnect
http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html
Sent from Cisco Technical Support iPhone App -
Question about 2504 Wireless Controller
Hello,
I am tasked with configuring a 2504 wireless controller. Is it possible to assign an SSID to an interface that has dynamic ap management enabled?
Scenario:
Location1:
1) 10.0.0.0/24
2)192.168.0.0/24 DMZ
Location 2:
1) 10.0.5.0
Both locations are routable using network 1 at each location. However, I need to configure several access points and send them to location 2. These access points will communicate with the controller at location 1 on network 1. Two SSIDs will need to be on network 1 at location 1. The other SSID will be on Network 2 at location 1. This network is not routable.
Thank You for your help.So this is how you want this to be setup:
Scenario:
Location1:
1) 10.0.0.0/24
2)192.168.0.0/24 DMZ
Location 2:
1) 10.0.5.0
Both locations are routable using network 1 at each location. However, I need to configure several access points and send them to location 2. These access points will communicate with the controller at location 1 on network 1. Two SSIDs will need to be on network 1 at location 1. The other SSID will be on Network 2 at location 1. This network is not routable.
Since location 1 is a flat network with only one subnet (internal) and one in the DMZ, you will configure WLC management/ap-manger port 1 on the 10.0.0.0/24 subnet. You can then map your SSID#1 to the management interface. Create a new dynaminc interface on the WLC and assign it an ip in the 192.168.0.0/24 subnet and place that on port 2. Connect port 2 to the DMZ. Now since you want everything to tunnel back to the WLC from location 2, you would leave the ap's in local mode. Devices in location 2 associating on SSID #1 will obtain an ip address in location 1 and tunnel back to the WLC and traffic will egress out of port 1. Devices that associate in location 1 or location 2 to SSID#2 (Guest) will tunnel back to the WLC in location 1 and traffic will egress out of port 2.
Since you want to tunnel traffic back to the WLC from location 2, you need to make sure your link has enough bandwidth or else the ap's will be bouncing.
If you setup the AP's in location 2 in h-reap mode, then you can place devices that associate to SSID #1 on the 10.0.50.0 subnet. Devices that associate to SSID #2 at location 2 will tunnel back to the WLC and egress out of port 2. -
Accounting in wireless controller
Hi everyone!
I have the question according to accounting of wi-fi users. Does wireless controller support accounting of all connections, sessions(duration,mac, ip address etc) that were made during a predefined ammount of time, for example one month? If controller does not, how can I achieve this?
Best wishes, ZhomartIn the Radius configuration part of the document you have provided it says following regarding to acconting functions:
"Accounting—The process of recording user actions and changes.
Whenever a user successfully executes an action, the RADIUS accounting server logs the changed attributes, the user ID of the person who made the change, the remote host where the user is logged in, the date and time when the command was executed, the authorization level of the user, and a description of the action performed and the values provided. If the RADIUS accounting server becomes unreachable, users are able to continue their sessions uninterrupted."
But can it gather the information about the connected devices, like it's type, mac-address, operating system etc? It would be very useful for security reasons to monitor the guest users, who don't have their own login. And if Radius can't do that, then would be your Boardless Network solution with MSE and Prime, proposed by you earlier, be the answer for our needs?
Maybe you are looking for
-
Log-on client 200 is not the same as BI clients "600"
Hi Experts, My data load got failed and when i checked the error message, it says " Log-on client 200 is not the same as BI clients "600"". Diagnosis You are using client-dependent BI functions in client 200. However, the standard BI client is 600. S
-
Mid month period not being calculated in pay slip
Hi Experts, Mid month period given in 0008 is not being calculated. e.g. if i hire some one on 16.01.09, then 0008 data should be calculated for those days only (e.g. 16 days) in pay slip. But in my case it is taking full amount of 0008. Can
-
How can i find my ipod without using the app
i lost my ipod and i dont know where it is. i dont own a iphone to use the finding app. what can i do?
-
Create a view - Service Requests and Incidents
Hi all, I have a Service Manager 2012 environment that has gone through an in-place upgrade from SCSM 2010. In the SCSM 2010 environment, Service Requests were implemented by extending the Incident class with an attribute that would denote whether th
-
Assassin's Creed: Unity Spin to Win Codes
One of the great offers for pre-ordering Assassin’s Creed: Unity at Best Buy is to receive a code to enter and receive chances to win prizes with the Spin to Win game. You’ll find all the details below on how we are sending these codes to customers t