Computer won't boot up, Windows 10.

Yesterday I was using my computer as a monitor for a friend to play a PS3 on. I have the Acer Aspire 5600U All-in-one PC so it has the HMDI ports for need. When he left, i just switched the screen back to the PC only to find an error code, I didn't catch what error it was but my computer was frozen, i let it sit there for maybe 45 minutes stuck on 100% so I force turned it off, when I tried turning it back on, it just turns on the power, & everything works, the hard drive the fans the external devices connected but the screen just turns back off after maybe 10 seconds, I don't have a mouse cursor or anything, just black screen turns on, then turns off, but power remains on & that's it. I have disconnected all the external devices to see if anything was bugging it but nothing worked. I've let the computer sit like that overnight thinking maybe it was just booting itself into a repar, nothing. I don't get a logo i don't get anything, just powers on, then screen turns off. If i power on the PS3 the screen turns on & works, & i have full functionallity of the buttons on the side, but the second i switch to PC it say's "PC No Signal?". No idea what to do.

ComputerGuy,
A dirty shut down is holding the power button down while it is booting up into Windows. Not seeing the display means you will need to time it a bit.
We have a 5600U here, so I went and hooked up a desktop to it via HDMI with the 5600U powered off. The 5600U will power on when it receives a signal from the desktop, but the 5600U is not actually powered on itself. Once the desktop is shut off it display a message that says HDMI no signal and then PC no signal. We pressed the power button on the 5600U and turned it on, repeated the process, and when the external desktop was powered off it changed over to the 5600U itself.
I think that you might be having a hardware problem, possibly the hard drive itself. Like I said, you can try the steps I listed and see if you can get that repair going, otherwise you might want to think about swapping in a different hard drive and loading it to see if that is the problem.

Similar Messages

Computer won't boot after windows 7 install.... :( [Solved]

I have 2 hard drives. The first drive is my main arch linux install. The second drive I use to install various operating systems. My school was selling windows7 for $30...I couldn't resist the cheap price...now I'm paying for it ><
I unplugged the hard drive with my arch linux install from my computer. (sda) Then installed windows 7 on the second hard drive. I reattached the first hard drive to my computer. (this was so i could avoid having to re-install grub)
My computer would not boot. I decided to install linux mint -- something I was going to do anyway -- that way I could boot into arch linux and fix things. Mint installed fine. But my computer STILL won't boot. I get grub error 22. What's up with that? Is this something to do with windows7?
Hard Drives:
/dev/sda1 ext2 /boot 100 MB
/dev/sda2 extended
/dev/sda5 ext3 arch / 130 GB
/dev/sda3 ext3 arch /home 166 GB
/dev/sda4 swap 1.72 GB
/dev/sdb1 ntfs windows7 65 GB
/dev/sdb4 ext3 mint / 19GB
/dev/sdb2 swap 1GB
/dev/sdb3 ext3 media 900 GB
Should I install grub to the MBR?
I checked to make sure that nothing in my arch linux install was erased using the arch install cd... I really need to get this fixed before classes on monday so any help would be appreciated.
Last edited by Meskarune (2009-10-31 04:26:39)

Xyne wrote:Then again, when you buy Windows, I suppose you're looking for the authentic Windows experience.
I was going to say, even at $30 you still managed to get the full windows experience at first boot!
Meskarune wrote:PS. I heard that windows will override the MBR when it updates... so consequently it is bad to install grub to the MBR in a dual boot system. Will I have to be reinstalling grub all the time?
God i hope not. just stay away from windows if that happens
just thinking about tihs is giving me headaches.
Last edited by toxygen (2009-10-31 03:06:12)

Computer won't boot to windows - Fail in Start-Up Tests - Possible Hardware Issue

My mate has given me his laptop to try and fix but when i runf the hp start up tests id comes up with this:
can anyone help?

Hi,
Now the image is viewable, it would look like the Hard Drive has failed and will need to be replaced.
As a further test, if you wish to rule out a possible ( although far less likely ) problem with the sata controller, you try the following.
1. Create a bootable Ubuntu CD - a guide on creating an Ubuntu CD and the download can be found Here.
2. When created, follow the guide on the link below to Try Ubuntu.
http://www.ubuntu.com/download/help/try-ubuntu-before-you-install
The 'Try Ubuntu' option runs the OS from the CD without the need to install on your HDD. If this runs Ok ( it will be slow running from a CD ), this would tend to confirm that the problem is just with the HDD.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Computer won't boot if the GTX 970 is plugged in

Hello everyone,
I just recently bought and assembled a new computer, however, the computer won't boot when the gpu is plugged in.
The motherboard I got is a MSI Z97I Gaming AC and the GPU is a MSI GeForce GTX 970.
When the GPU isn't plugged in the mobo, everything boots up fine and I was able to check with the bios that every other elements of the computer where recognized fine. When I plug in the GPU however, the system won't boot. The fans of the case, the mobo AND the GPU's are working and the GPU's leds also on, so it shouldn't be a PSU issue (I use a 750W PSU so that should cover it). However, no boot at all.
I don't really feel like trying to plug the GPU in another computer if it's just some compatibility issue or whatnot that you may be aware of. Maybe the bios doesn't recognise it ? The version is e7920IMS V1.0, I wasn't really able to find any kind of information regarding the latest versions online.
Thank you,
Yann

Here it is, follow the below to update to 1.4:
>>Use the MSI HQ Forum USB flasher<<
A.) Download the attached archive and place it on your desktop. Do not decompress.
B.) Download and install the Forum flash tool.
C.) Insert your FAT32 formatted usb stick.
D.) Make sure that all win 8 options are disabled. (Fast Boot etc) Also make sure the legacy USB is enabled.
E.) Start the forum flash tool and select option 1. Then point the tool at the compressed archive we downloaded earlier. Then to your USB Flash Drive.
F.) Boot to the USB
G.) Now follow the directions and let the tool flash
H.) After flashing reinstall ME drivers in Windows: http://download.msi.com/dvr_exe/intel_me10_mb.zip

Computer won't boot after installing MFP M127FW

My computer won't boot to my hard drive after installing my new MFP M127FW printer unless I first unplug the USB cable from the printer and then turn on the computer. My BIOS is set to boot from my hard drive, not from a USB drive, so what did the installation of the MFP M127FW drivers and software do to my computer? I assume this has something to do with the Smart Install feature.
This question was solved.
View Solution.

Hi @frcraig ,
I see that you are experiencing issues with the computer booting up when the printer is connected by the USB cable.
I would like to help you out with this issue today.
Most likely it is the Smart Install on the printer causing this. The printer looks like a disk drive.
On the printer, touch Setup, Service, Smart Install and turn it off.
If you are still having issues, in the system BIOS, disable the Boot from USB device option and the USB Legacy Support option. Doing this will allow the PC to complete the boot process to the internal hard drive and allow you to enter Windows. If this does not work for any reason, you should boot your PC before connecting the USB drive. Once the computer is fully booted into Windows, connect the USB drive and wait for the operating system to detect the drive.
Important: Do not disable the USB Legacy Support if you are using a USB Keyboard. Doing so will prevent you from being able to use the keyboard during the booting sequence.
What kind of computer do you have?
If you need further assistance, just let me know.
Have a great day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Installed new bios and now computer won't boot

I just installed the new bios for my HP Pavilion dv6704nr Entertainment Notebook PC laptop off the hp website and now my computer won't boot. I tried removing all power (including the 3 volt battery) and it still won't turn on. I Then tried the windows + B keys at boot and still nothing. I have windows7 64 bit OS and installed the vista 64 bit bios (the only 64 bit bios they had). Any help would be greatly appreciated.
Thanks

try runnng system restore from recovery manager, if the OS is changed then run recovery
***Click on “Kudos” STAR to say thanks!***

Computer won't boot up after installing SIIG card

Hey Everyone,
I having problems with my SIIG FireWire 2-Port PCIe DV card that I've installed into my PowerMac G5 Quad. With the card installed the computer will not boot up, which is the same thing that happened with my previous two models of the card. I installed a new card yesterday and it worked fine all day, but after shutting the computer down for the night and then restarting it in the morning I am experiencing the same problems. The light on the front of the computer turns on, but the screen does not, and after about a minute a loud fan noise comes one. I have the card installed in Slot 2. In Slot 1 I have a ProTools HD card and in Slot 3 I have an AJA Kona LHE card. Even with all of the cards removed the computer still does not boot up. Anyone seen this problem before? Any help or information anybody can offer would be greatly appreciated.
PowerMac G5 Quad Mac OS X (10.4.8)

Hi, I had the same problem with my dual core G5.
I installed the card and my computer won't boot up. The screen stays gray and the fan keeps spinning.
I contacted SIIG and they said the card is defective, which, I doubt it is.
I then returned it for a refund.

If usb is plugged the computer won't boot

Hi there. I have recently started to experience a new type of problem. I have two usb hdds connected to a usb hub. I've never had any problems with it(the hub). After I installed the last update 10.7.3 everytime I restart my computer if I have the hub (with all my hdds and other devices) connected to my computer, the computer won't boot. It get up to the white screen (before the loading wheel). If I unplug the usb cable it starts booting inmediately.
The funny thing is I didn't change anything lately. It started to do this yesterday.
Thanks

Is the hub powered? If not that is probably your problem. The hd's are sucking power but can't get enough to power up and that is probably stopping the MBP from booting.

My computer won´t boot and restarts at Apple logo with the spinning thing

My computer won´t boot and restarts at Apple logo with the spinning thing and I can´t get it to work.
Before this happen I had left the computer on without a cable plugged in and so it ran out of power.
I just pressed the startbutton again after I´ve plugged it in and this problem started.
Any ideas?
Mattias
Sweden

WRONG FORUM Sorry

Is there an emergency eject hole on the newer iMacs. disk stuck in drive and computer won't boot.

Is there an emergency eject hole on the newer iMacs? I have a disk stuck in the drive and the computer won't boot. Need to get this disk out to load repair disk.

If you are getting nothing at all you should take it in for repairs.

Installing Windows 7 on my bootcamp partition (mid-2009 mac book pro with mountain lion) My computer won't boot from the Windows 7 Install DVD.

Hello,
I have been trying to install Windows 7 on my macbook pro (mid 2009, MBP53). I have successfully created a bootcamp partition using the assistant. When the computer tries to boot from the windows 7 install dvd, the screen is just black. The dvd spins for a bit, then stops and the computer is just black (no blinking cursor).
Any advice would be very appreciated.
Thanks.

What kind of an install DVD are you using for Windows?
You can use any DVDs that are hardware specific. Only the full non-hardware soecific DVDs work on the Mac.
Allan

I changed the name on my computer from the Windows side and now it won't boot to Windows (bootcamped)

I changed the name on my computer on the Windows side and now I cannot boot to Windows 7 (bootcamped). Any suggetions?

Hello cmcnanna,
I'm sorry to hear you are having these issues with your iPhone. If your iPhone isn't starting up or responding at all, you may find the troubleshooting steps outlined in the following article helpful:
If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support
If that does not resolve the issue, you will most likely need to have your iPhone evaluated and/or serviced. You may find the following page useful in that case:
Apple - Support - Service Answer Center
Sincerely,
- Brenden

Computer Won't Boot Up

Here is my issue, my computer one day was working fine and the next it won't boot properly.
System Specs: Satellite T235D-S1345RD (Laptop) - Windows 7 (64bit) - BIOS 1.7 - 4gb RAM -
I have gotten the computer booted one time. I am unsure why it did that time but did not do it another time.
Since that one time I put the computer in hibernate and when I tried to bring it out it told me it failed when coming out of hibernate so it went to reboot and now won't boot.
Here are the few steps I have done to try and get it working. When it boots up it gives me an error message (says that power failed or for some reason it did not boot)
I have ran "Repair Computer" and it does not do anything. I try start windows normally and it goes no where.
So I then tried F8 and got into the Advanced Boot Menu. First one I tried was Start Windows From Last Known Good Configuration. (or something like that I forget the exact wording)
When it does that the computer will start to boot up go to the "Windows Loading" screen and then it flashes a blue screen (there are words there but it flashes so quickly I cannot read it) and it goes back to the boot screen and acts like it is restarting and continues in that loop.
Next step - Enter F8 again tried "Repair Computer" and it loads to a black screen with a Cursor but nothing ever happens. I have given it over 30 min and nothing happens.
So next step- I enter F8 again and try to boot up in safe mode and again when it loads it flashes a blue screen and then nothing.
EDIT - I found how to show the blue screen. It says UNMOUNTABLE_BOOT_VOLUME. Not sure what else I should do after I get that error message. Message Reads:
It reads UNMOUNTABLE_BOOT_VOLUME and says if it's the first time I've seen the error screen, to restart the computer. Then it tells me if it appears again, to check and make sure any new hardware or software is properly installed.
"If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode."
END EDIT
Next Step: I come to you guys here on this forum. I am a bit perplexed and lost at what to do. I wonder if this is a virus but I cannot get the computer to respond to try to get into it to check.
Ideas? Advice? What should I try? I can get into the F8 menu but not sure what else I should try. I will try anything to get this computer up and running!
Thanks for any and all help.
Lynda

Hi:
The 24 character failure ID usually indicates HDD is failing/has failed. You need to replace it with a new one.
Specs: http://support.hp.com/in-en/product/HP-Pavilion-dv6-Entertainment-Notebook-PC-series/5191856/model/5...
Manual: http://h10032.www1.hp.com/ctg/Manual/c03099531
Check warranty: http://h10025.www1.hp.com/ewfrf/wc/weInput?cc=us&lc=en
Order recovery USB: http://support.hp.com/in-en/product/HP-Pavilion-dv6-6c13cl-Entertainment-Notebook-PC/5191856/model/5...
Contact HP: https://support.hp.com/in-en/contact-hp/product/HP-Pavilion-dv6-6c00-Entertainment-Notebook-PC-serie...
If you're under warranty, HP would send you replacement HDD.
If you're not, buy any branded 2.5" SATA 9.5mm thick internal laptop HDD and replace it yourself. But HDD of at least same capacity HDD as the one that came with your laptop (640gb) so that recovery media would work -
Go through page 56-58 in the Manual for replacement procedure. It's quite simple DIY job.
Something like this:
http://m.newegg.com/Product/index?itemnumber=N82E16822236561
If you've not yet created the Recovery media to restore the factory settings after replacement, you have to order a set of Recovery USB from HP.
For salvaging the data from old HDD, I suggest you take out the drive. Connect it to another PC using SATA to USB adapter - copy all the files you need.
http://www.amazon.com/Anker®-Converter-Adapter-Cable-included/dp/B005B3VO24
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

Computer won't boot up! Please help.

How's it going guys, I have a powerbook G4 that I have owned for a few years now. I woke up this morning to my computer making a weird processor noise, it was a repetitive noise, and my screen was frozen. I thought my computer had frozen or something. I did a hard shut down on my laptop and my computer will not boot up mac osx. It stays Stuck on the Apple page. I've tried taking the battery out, i've tried new ram, and i've tried restarting it several times, and to no avail has my computer booted back up. I have the mac osx disc and that won't even load up. Can anyone please help me out. I'm in dying need of my laptop! Thanks! - Brian

When I try and repair the disk it reads the 74.5 GB TOSHIBA MK8025GAS Harddrive but It doesn't read the HD drive right under it. I click on the toshiba disk and i tried repairing it and it gave me an error message. The message reads : "First Aid Failed. Disk utility stopped repairing HD because the following error was encountered. The underlying task reported failure exit."
The actual disk utility window reads "Invalid node structure" in red letters. "The volume HD could not be repaired : Error : The underlying task reported failure on exit. 1 HFS volume checked : 1 volume could not be repaired because of an error. Repair attempted on volume 1, 1 volume could not be repaired.
Any suggestions? And how do i go about doing an archive install? And how do i go about using diskwarrior? Thanks guys. I really appreciate this. I need this computer up and running for school. I'm actually at my college library typing this out. - Brian

Windows won't boot! Windows protection error.

I just upgraded my mother board to a MSI and now I can't boot to Windows at all! I'm using two different versions of windows on seperate hard-disks (never at the same time) and both won't boot. I can get to Safe-mode in Win98. My system was fine before I upgraded.
System:
Motherboard - MSI, K7N2 Delta, Nvidia nForce 2 based.
CPU - AMD XP 2400+ T-bred.
CPU Cooler - 2 x 8000-rpm fans on Kanie Hedgehog (big heatsink).
Memory - Kingston 256Megs, two sticks for 512megs. (Says: Kingstort /VR, KVR266X64C25/256. I don't know much about memory.) It fits the DDR1 slot.
Graphics - Nvidia 5600.
Power supply - New, Allied brand, ATX-style, 450Watt.
OS - Windows 98, Windows XP (SP1)
(Win98 and WinXP are on seperate hard disks. Never used at the same time).
Problem:
1. When I boot to Win98 it just says "Protection Error, you will need to restart your system".
2. When I boot to WinXP it says "A problem has been detected and windows has been shut down to prevent damage to your computer."
Fixes and diagnostic:
1. Diagnostic lights on mother board cycle and and say OK.
2. I can get to Win98 Safe-Mode or Command prompt.
2. I don't have any other PCI cards installed except video.
3. I'm using only one of the memory sticks just to rule out the other (tried both).
4. I have most of the on-board peripherals disabled (sound, ethernet, serial. parallel, etc...).
5. Tried upping the voltage on memory. Same problem.
6. Tried setting memory for 100mhz. Same problem.
7. Tried reseating the memory. Same problem.
8. CPU temp is well within range at around 109F.
Questions:
What could the problem possibly be? I will try anything!
1. Is there some kind of safe mode for the hard drive settings?
2. Is there some kind of safe mode for memory speed?
3. Give me some hints! Upgrading the MB shouldn't be this hard! What am I overlooking? Thanks for any replies!

Quote
Originally posted by Falconis Progmadn
This can easily be caused by not setting the jumper pins correctly when having both of the HDDs installed on the same IDE cable.
Obviously you would have to change the jumper short every time you retry each HDD.
I am not following your line of thinking here. Win98 needs to on the primary drive, primary channel in most cases, yet XP can boot from any location, and any drive letter. So why would there be a need to constantly swap jumpers? Only thing needed is the Boot.ini file on the main drive, and it will boot from any OS listed there.

Computer won't boot up, Windows 10.

Similar Messages

Maybe you are looking for