Computer won't start from hard drive or CD, and won't perform system recovery.

I have an HP Pavilion g7-1314nr. Yesterday it froze and I held down the power button to turn it off. After turning it back on, it started a disk check. I turned it off during the disk check, and upon trying to boot it back up, it told me booting failed and to press CTRL-ALT-DELETE to try again. After multiple attempts, it stopped displaying this message. Under system diagnostics, I ran a boot test, and it failed. Attempting a system recovery brings up the start-up windows logo, and then a black screen with an enlarged cursor. This morning, I inserted a recovery disk and told it to boot from internal CD/DVD drive. Like system recovery, it brings the Windows logo, and then a black screen with an enlarged cursor. My computer is incapable of booting from either the hard drive or a CD. What do I do?

Hi @TeridaxXD001 ,
Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Pavilion g7-1314nr Notebook and issues with Windows 7 and starting up. I recommend to restore the BIOS defaults. You could restore the BIOS with this document selecting the reloading the BIOS default settings which should resolve the fan issue.
Here is a link to computer won't start for Windows 7. There is a section on getting past the HP Logo screen.
If that does not help at the end of the document it shows you to do a hardware test.
Please note remove any and all USB devices before troubleshooting. Disconnect all non-essential devices
Hope this helps you out.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Similar Messages

Powerbook G4 10.4.11 won't start from hard drive . Tried repair, " The underlying task reported failure on exit (-9972).Invalid sibling link,invalid B tree header, invalid map node,invalid record type,the volume needs to be repaired.

Powerbook G4 10.4.11 won't start from hard drive . Tried repair, " Invalid sibling link,invalid B tree header, invalid map node,invalid record type,the volume needs to be repaired.Powerbook G4 10.4.11 won't start from hard drive . Tried repair, " The underlying task reported failure on exit (-9972).Invalid sibling link,invalid B tree header, invalid map node,invalid record type,the volume needs to be repaired.
The underlying task reported failure on exit (-9972).

kauribill wrote:
" The underlying task reported failure on exit (-9972).Invalid sibling link,invalid B tree header, invalid map node,invalid record type,the volume needs to be repaired.
The underlying task reported failure on exit (-9972).
This is a directory issue that Disk Utility cannot fix. Although it manifests itself as a software issue sometimes it may be hardware based. See DiskUtility reports "Underlying task reported failure" when repairing avolume http://support.apple.com/kb/TS1901?viewlocale=en_US". You can try using a utility like TechTool Pro, Drive Genius or Disk Warrior to repair and replace the directory. Another option would be to use the Archive and Install feature to reinstall. If the problem returns after correction you may have a failing or failed HDD.
cornelius

HT1420 how do i Deauthorize a computer that has had the hard drive lock up and can not get it working

how do i deauthorize a computer that has had the hard drive lock up and can not get it working

You can only deauthorise individual computers directly on them. Otherwise if you've reached the 5 computer limit, then you should be able to log into your iTunes account and 'deauthorise all' (which you can only do once every 12 months) and you can then (re-)authorise up to 5 computers : authorising and deauthorising.

Mac Book Pro won't start from hard drive when turned on

I have a new 15 in Mac Book Pro with 10.8.1. When I turn it on it always boots to the disk utilities rather than my harddrive. I select my startup disk and reboot. It starts fine. But when I shut it off the same sequence repeats. I have verified my drive and selected the hard drive as my startup disk.
What is happeneing? What should I try?

Step by Step to fix your Mac

Bronze keyboard Will not start from hard drive

This computer (333 Mhz Lombard 192MB ram) has a 40GB seagate HD recently installed, It has Mac OS 10 on it and 9.2.1. I've run multiple tests on it using Apples Mac Test pro and all the tests have passed. It starts readily from the CD I have also recently replaced the battery and pram battery. All i get from the computer at start up is the flashing ? mark blinking system folder. I've reset the pram and power manager, not sure whats wrong. any help would be appreciated. Thanks, Mark

The blinking ? means the Mac can't find a valid startup system.
Look at A flashing question mark appears when you start your Mac
http://docs.info.apple.com/article.html?artnum=58042
Are you trying to start up in OS 10 or OS 9? If OS 10, depress the Option key at startup which opens to the Startup Manager window. Then select the OS 9 icon & click the right arrow. If OS 9, do the same but select OS 10.
 Cheers, Tom

DV7-6185us wont boot from hard drive.

I recently installed a new hard drive after the one it came with completely crashed. After installation of new hard drives, I inserted and installed all of the recovery disks needed for the new hard drive. Upon completetion it said it needed a restart and after restart I get a message saying I need a OS for the hard drive for boot up.
I went into my bios to make sure the hard drive was first in boot order which it is but when trying to pick where to put from on the bios screen it only give me the cd option. I ran a full diagnostic of the hard drive and everything checks out. I made sure to unplus the hard drive and tried a different slot and still get the same thing. Installation when fine but still won't boot from hard drive.
Is there something that i'm missing? The hard drive is fine. So what could it be?

Hi,
Assuming this is just a problem with the recovery media, here's an alternative option you could try.
Before trying the following, make sure you can still read the 25 Character Product Activation key on your Windows COA label ( 5 blocks of 5 alpha/numeric sets ).
An example of a COA Label can be seen Here.
You can create a Windows 7 installation disc yourself using another PC - just download the correct Disc Image ( this must be the same version that originally came with your notebook - this is listed as Windows 7 Home Premium ) from the link below and use an application such as ImgBurn to burn the ISO correctly to a blank DVD - a guide on using ImgBurn to write an ISO to a disc is Here. These Images are clean and from a well-respected source - Digital River.
Windows 7 Images.
Use the disc to perform the installation, enter the Windows activation key found on the COA Label when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
Any additional drivers and software you may need can be found Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Powerbook won't boot from hard drive or restore disk

I've looked through some of the older posts here and none of them exactly matches my problem, and I've tried just about any possible solution I can think of.
I recently noticed that my PowerBook was acting a bit strange. It was making more fan noises than usual, and sometimes the computer would make the very last noise it makes as it shuts down (which is the hard drive coming to rest, I suppose?), though the computer would still be running. Then, yesterday the computer froze and I hit command-control-power, and when the computer restarted it gave me a folder icon blinking between a question mark and the Mac logo.
I tried restarting again, but I had no luck. Now when I try to start up I get the start-up chime, then I get one of three things:
1) If I restart it without a CD in the drive, I get the blinking folder.
2) If I restart it with the Software Restore and Install DVD in (but without holding down the C key), it gets to the Apple logo and shows the spinning pinwheel or whatever you want to call it, then freezes and some nasty horizontal bars pop across the screen.
3) If I restart it with the Restore & Install DVD in and I hold down the C key, it gives me the Apple logo, then the "Your computer has encountered a problem and needs to be restarted" box pops up.
I tried zapping the PRAM--no luck. I tried Open Firmware; the screen pops up, then I type in "mac-boot" and I get the same thing as in #2 above.
I used the Hardware Test CD; it told me that there was a Mass Storage error with the error code 2STF/1/4. That doesn't sound too pleasant.
I'm not sure what caused it; perhaps it was a heat thing, but I moved it too a different surface. All the hardware is original except for the Airport card, which has worked fine since Christmas. The only recent software changes I've made were updating to the newest versions of iTunes and Firefox. It doesn't seem like a hard drive problem, since the boot CD won't work.
Am I doomed to sending Apple a couple hundred bucks to fix this? The laptop is right at three years old, so even if I'd had AppleCare it would be expiring right about now. Or is it time to buy one of those MacBooks? Or just buy a couple PC's and use each one till it breaks, then throw it out?
Thanks,
Kevin

I finally got to another Mac. I installed Mac OS X onto my Firewire drive, then hooked up the drive to my Powerbook and used the Startup Manager. The drive showed up on Startup Manager and I chose to boot from it. When I did, the startup process continued briefly, then froze just like it does when I try to boot from the CD.
I know my Powerbook's hard drive is shot, and to be honest, I'm fine with that--there isn't any critical, essential data on there. I tried starting the Powerbook up in Target Disk mode, but that doesn't work either--I hear the chime, press T, but the screen stays black.
Now my question is: can I rip the hard drive out? Or do I have not only a bad hard drive, but also something else gone wrong? I'm not opposed to buying a new internal hard drive and installing it myself if that will fix the problem; what I don't want to do is spend a few hundred bucks to take it to someone who's only going to tell me that my omputer is now a paperweight.
Also, my Powerbook isn't one of the ones with a recalled battery. The computer can get pretty hot, even when sitting on a desk, but I just figured that was normal.
Thanks,
Kevin

My computer recently had a new hard drive installed. Now the music I have added to itunes won't sync over to my ipod

My computer recently had a new hard drive installed. Now the music that I have added to itunes won't sync over to my ipod. I have the selections checked, but still no luck.

See Recover your iTunes library from your iPod or iOS device.
tt2

G3 won't boot from hard drives or startup (original) CDs

I recently installed OS X 10.4 on my Mac G3 (6GB HD, 256MB Ram, blue & white). It ran fine for one week. After one week, when it would boot up, I would have 800 MB of free space. Within a few minutes I would get an out of memory error and my HD would have zero space left...effectively locking up the machine. I was told to increase my memory to 1GB (I did) and to install a new HD (I did, a Seagate 80GB). I partitioned the Seagate into two equal partitions. About the time that the OS finished this task, I received a security upate installation dialogue asking me in install a new security update. I said "OK". About the time the security update was installed, the system ran out of memory...then asked me to restart the machine. I have not been able to get it to restart since. Can't startup with the OS9 CD, the OSX CD OR Diskwarrior. I keep getting the same message..."panic(cpu 0 caller 0x002DE020): Unable to find driver for this platform: "powerMac1,1". Then there is a whole lot of other stuff with a final comment "We are hanging here..." I can't seem to find anyone to help me with this. I brought the machine back to its orginal configuration...didn't work. I disconnected the old 6GB HD and was able to install OSX on the new drive...but, after installing on the new hard drive, I rebooted and I am back to the same errors. I keep getting the OS9 flashing folder with "?"/face. HELP!
Thanks,
Pat
G3 Blue & Whote Mac OS X (10.4.4)

You are having kernel panics as shown in this Apple doc.#106227.
Do everything, in order, in Dr.Smokes Resolving Kernel Panics and don't leave out any steps.
Quote from Dr.Smoke "My FAQ is a roadmap: start at the beginning and work through to the end, following the instruction in the order specified, including the "If all else fails..." section if a cause or resolution is not found in an earlier troubleshooting step therein"
Here's more at a brody's KP site.
Cheers!
DALE

Start up issue with clicks from hard drive

My Macbook Pro 17" with Maveric does not load beyond grey apple logo during start up and has intermittent clicks sounding from hard drive. I've tried the following to resolve:
1. Removed and reinstalled the RAM modules followed by clearing the PRAM on restart... ineffective.
2. Restarted holding the option key. This showed my 1 year old hard drive was still available. However, selecting it resulted in the same failure at the grey apple logo.
3. My previous Snow Leopard Recovery disc also ineffective. The eject button does no eject the disc either.
4. Target disk mode also fails.
5. Remote Recovery start up (command R) hangs on spinning wheel.
Please advise.

You may have to resort to using something such as DiskWarrior or Data Rescue 3 to try an repair the drive to the point where you can recover some of your files.
I assume that you have no backups?
Clinton

Iphone and computer died, need to get the files from hard drive

Iphone and computer died at the same time, my hard drive on the computer is ok, i did a external connection of my hard drive to my laptop, my iphone was backed up on itunes on the computer which are on the hard drive, how do i extract contacts and other files from the hard drive thanks

If the old drive is not accessible then, no, you will not be able to access all your files on it. In this case you may need to look at the following:
Basics of File Recovery
Files in Trash
If you simply put files in the Trash you can restore them by opening the Trash (left-click on the Trash icon) and drag the files from the Trash to your Desktop or other desired location. OS X also provides a short-cut to undo the last item moved to the Trash -press COMMAND-Z.
If you empty the Trash the files are gone. If a program does an immediate delete rather than moving files to the Trash, then the files are gone. Recovery is possible but you must not allow any additional writes to the hard drive - shut it down. When files are deleted only the directory entries, not the files themselves, is modified. The space occupied by the files has been returned to the system as available for storage, but the files are still on the drive. Writing to the drive will then eventually overwrite the space once occupied by the deleted files in which case the files are lost permanently. Also if you save a file over an existing file of the same name, then the old file is overwritten and cannot be recovered.
General File Recovery
If you stop using the drive it's possible to recover deleted files that have not been overwritten with recovery software such as Data Rescue II, File Salvage or TechTool Pro. Each of the preceding come on bootable CDs to enable usage without risk of writing more data to the hard drive.
The longer the hard drive remains in use and data are written to it, the greater the risk your deleted files will be overwritten.
Also visit The XLab FAQs and read the FAQ on Data Recovery.

Itunes from hard drive to new computer

Hi All
I have the following issue, I have my itunes (all music, tv shows,films andf iphone 4 back up) on an external hard drive that has 232GB of space I have read that i need to consolidate the libary to move it, but i have 137GB of information and it copies the folder to the same location i do not have enough space on the external hard drive or my old computer (it only has 60GB space) to do the consolidation.
I have plugged my hard drive into my new computer (sony running windows 7 64bit home premium) but cannot open itunes via the external hard drive.
My problem is I want to move my itunes to the new computer (which has a 500GB hard drive) how do i do this or do i need to buy an addtional hard drive to move the files (i do not wish to pay out more).
Does anybody know a way of doing this with the hard drive and the external hard drive (my other concern is that i do not want to lose all my contact on my iphone).
Thanks Nick UK

Hi Perilman,
Welcome to the Apple Support Communities! I understand that all of your iTunes media is on an external hard drive and you would like to move that media onto your new Windows computer hard drive. The following article has step by step instructions for this specifically. Part 5 in the External drive section is probably what is going to be most relevant to you.
iTunes: How to move your music to a new computer
http://support.apple.com/kb/ht4527
Part 5: Copy music to your new computer
To copy all your music files (including the library file that holds all your playlists and other settings) to your new computer:
I hope this helps,
-Joe

Mac OS 10.5 / I deleted the " Private" folder ... and emptied the trash. So the folder and its contents no longer exists on my computer at all !!! I do have the OS dvd that i purchased years ago... But my computer will not start from it on its own. My

Mac OS 10.5 /
I deleted the " Private" folder ... and emptied the trash. So the folder and its contents no longer exists on my computer at all !!!
I do have the OS 10.5 dvd that i purchased years ago...
But my computer will not start from it on its own.
My question is what is the open source or terminal language code used to tell my mac to look in the DVD rom drive for startup info? I know that im not the only person in this world who has deleted the "PRIVATE" folder and emptied the trash so it no longer exists on their machine...
That said theres gotta be a common fix for a Power PC G4 that has the OS X dvd in the rom drive but wont look to it to reinstall the vital contents of the PRIVATE folder.
Once again there is not a copy of this file or its contents in the recycle bin...
Also rebooting the machine , pressing and holding the letter C does not prompt the machine to look to the dvd rom drive.
I was reinstalling pro tools and figured I would make some room by cleaning my computers HD...
Lol It was a bad choice to delete this file ...
Thanks guys

Okay sorry it took forever to respond... But for a while there I gave up on this computer!!!!
Money's been tight lately , so taking it in to a professional was not yet an option... though I did consider it eventhough.
Anyway long story short im glad I didnt spend any money because I already had all the tools necessary to fix this issue but was going about it in the wrong way. Okay so here is my scenario and the breakdown... Though this may not fix the issue for everyone :( which *****... But I know we all will have different circumstances.
Anyway here we go...
Okay so first things first.... Years ago I purchased the OS 10.5.1 disk ... So that has always been in my possession!!!!
I realize that some may not have a disk to reflash your OS to your hard drive... but if you do your in luck.
2ndly ... I had an external harddrive with all of my itunes downloaded music so it was more than okay with me to delete my primary HD because all the important stuff could either be copied over or repathed to be located.
-------If you dont want to read through the whole story the fix is summed up in the bottom section-------
Okay so now the SOLUTION!!!!
By trial and error , and pure boredom I opened up my computer to clean the inside...
AND
"Disconnected the primary HD"
and just because ....... REBOOTED my computer. Just to see what it would do.
Upon restart and though it looked like it would repeat its usual cycle...
About 1 minute in to that process my computer froze for about 2 seconds and flashed to the OS installation screen.
Mind you I havent seen this screen yet... Probably hasnt been since I installed the OS years ago.
After a bit of trial and error...
I decided to tell my computer to startup from the OS 10.5 disk located in my dvd rom drive and restarted once again...
this setting is under
Utilities / startup disk
After a little more trial and error ... I realized that I could reconnect the primary HD , restart the machine and return to the OS installation menu.
So upon this discovery
I went to the Disk Utility located under Utilities
Highlighted my primary HD located in the left hand column
Once highlighted ...
In the heading section on the right I selected the option
Erase
in which I erased My current OS on my primary HD ...
I used the first option in the list under security... Because it seemed like the least invasive and would take the least amount of time to see if this process would actually work.
I FORGOT to add something...
Another reason why I deleted my primary HD!!!!!
I forgot to say that it WOULD NOT!!!!! Show up in the STARTUP list as an option...Even After multiple reboots....
But like clockwork... Once I deleted its name IT SHOWED UP as an option!!!!
So back to the next step...
I returned to the STARTUP option under utilities ... And was then able to see MY primary HD now as a startup option...
But ofcourse it had no name because it we previously erased it.
So when Clicking my newly erased HD ... I was almost immediately prompted to REINSTALL the OS ...
Which said it would take about 57 minutes ... But I believe was alot less...
My issue was resolved ... My computer then stated the install was SUCCESSFUL!!!!!!! :))))))))))) lol ;)
It was like I was setting up for the first time ;) asking for my registration info...
The dilemma of deleting the private folder and emptying the trash is finally over resolved. Done ... and no extra money spent!!!!!!!!!
Its really crazy that the information for such a simple thing is not readily available. Especially being such a simple fix.
I know im not the only person who's had this issue , because i've seen numerous posts with similar wording.
I also know I wont be the last person to have this issue... So I hope this synopsis makes sense.
-------One more time the fix------
*Insert your OS dvd into your dvd rom drive.
*Unplug your primary HD or corrupted startup disk
*Reboot your machine...
Upon restart your primary HD will not be recognized...
* you will then be prompted to select your language.
Once selected
*Click Utilities/startup... Highlight the the selection that refers to the OS dvd located in the dvd rom drive.
* Click restart...
!!!!!!!!!!Be sure to reconnect your Primary HD Before your computer restarts and you hear the chime!!!!!!!!
If you do not replug your HD before the chime it will not be recognized.
In that case restart again.
Upon restart once again
*Choose your language...
*Click Utilities / disk utility
In the left column select and
*Highlight your HD ...
Then towards the top portion / center of the page
*Click the heading Erase
Then on the page toward the bottom
*Click security options
This will then provide erase options.
I USED THE FIRST OPTION
"Dont erase data"...
*click OK
* click erase...
Once erased which should take a few seconds
*Cancel the disk utility...
* Click Utilities / startup
And your newly erased HD should now appear in the list.
* Select your drive from the list by highlighting
It should no longer have a name.
*Once selected, you will then be prompted to restart and install the OS to your newly erased HD...
Thats it!!!!
Once everything reinstalls re-add your personal info or registration info and you are up and running.
Goodluck ;)

Running Itunes library on a new computer off of an external hard drive

Hello, I've recently purchased a Macbook and an external hard drive. I transferred all my files from my old Mac onto my external and would like to try to run my itunes library from there through my new laptop as opposed to putting all the files onto the new computer.
Is it possible to have the files exclusively running off the hard drive and never going onto the new macbook? How might I go about doing this?
I've tried following some of the video tutorials but that just seems to route you to do it from your old computer off of a external hard drive, and nothing to do with using it on a new computer.
Basically what I want to do is get everything running off the external (all the old computer's data) and none of it ever to set foot on my new Macbook.
Thank you all in advance for your help!
-Rob

Assuming you use the iTunes default settings where iTunes copied added items to your iTunes folder and organizes your library (meaning - everything is all self contained in the iTunes folder), then all you have to do is drag & drop your iTunes folder (not just the iTunes Music folder you find inside the iTunes folder) to the external drive and copy the entire thing.
If you want to test that it worked or would like to actually start using it from that location instead, use these instructions when you start iTunes to point it to the new location...
How to open an alternate iTunes Library file or create a new one
http://docs.info.apple.com/article.html?artnum=304447
If you are just testing to make sure a backup copy works and still want to use the internal location, then close iTunes after you verify it works, and restart iTunes again with the same instructions and point it back to your internal drive (original) location. Otherwise you are all set to use the library from the external location.
When you move the external drive to another computer, use the same start up instructions above to point your iTunes on that computer to the library on the external drive.
Additional info...
Back up your iTunes library by copying to an external hard drive
http://docs.info.apple.com/article.html?artnum=307074
Cheers,
Patrick

On a macbook I purchased secondhand hard drive got corrupted and I started to get the flashing folder with the question mark, I purchased a new hard drive and snow lion install DVD I installed the hard drive and tried disc but kept getting blinking folder

On a macbook I purchased secondhand hard drive got corrupted and I started to get the flashing folder with the question mark, I purchased a new hard drive and snow lion install DVD I installed the hard drive and tried disc but kept getting blinking folder

Welcome to Apple Support Communities. We're users here and do not speak for "Apple Inc."
Power on the computer and insert the DVD immediately.
Hold down the 'C' key to boot from the Snow Leopard DVD.
http://support.apple.com/kb/ht1533
After selecting the appropriate language, if necessary, select Utilities, and Disk Utility.
You'll likely need to partition and format the new drive before it's recognized.
http://manuals.info.apple.com/MANUALS/0/MA161/en_US/MacBook_13inch_HardDrive_DIY .pdf
(Yes, these instructions ARE 7 years old, but the procedure is the same for installing from DVD media.)

Computer won't start from hard drive or CD, and won't perform system recovery.

Similar Messages

Maybe you are looking for