Conecting AEBS and AExpress to a Verizon wireless router to extend network

I have Verizon Fios and with that I have the wireless router that Verizon provides. The signal is great as long as I am in my office. However, in other rooms in the house the performance is decreased significantly. Before having this router I was set up with an AEBS and the performance was great.
My question is, "how can I extend my network by linking the AEBS and/or the Express with the Verizon router?" I have to have their router so I would be using the AEBS or Express to boost the signal through my 2 story brick home.
Please help if you can...thanks

I'm not familiar with the Verizon FiOS-supplied routers, but you should be able to connect an AirPort Extreme Base Station to the FiOS router via Ethernet cable and create your own wireless network with all Apple devices set up in bridge mode.
Turn off the wireless network on the FiOS router, if possible. The idea is that all wireless clients will receive IP addresses from the FiOS router but will connect to it wirelessly via the Apple devices.

Similar Messages

Good morning. I've read in some blogs and forums that the verizon wireless works in Europe but my question is if it works with portugueses cards (like vodafone sim)?

Good morning (at least here in Portugal)
My question is that I want to buy the new Iphone 5C, but I want to use it here in Portugal. I was in the store menu looking for it and it appears that I have to stay with a network for two years, if not the price will increase significantly. I want to buy it online because the Iphone will only arrive in Portugal in December and probably it will be more expensive. I've read in some blogs and forums that the verizon wireless works in Europe but my question is if it works with portugueses cards (like vodafone sim)?
Thank you very much for the attention.
Daniela João.

The Verizon iPhone 5 is sold as unlocked. You can buy it full retail and use it anywhere you want. However, you won't get LTE in Europe and you won't be eligible for warranty service unless you take the phone back to the U.S. You won't be able to buy one on a contract unless you can pass a U.S. credit check. The minimum monthly cost would be $59.99 plus tax. I assume that all of this information will be true of of the 5C as well.
Wait and buy the phone in Portuagal.

Using time capsule model A1409 and trying to use it as only backup. Already have Verizon wireless router. Do not know which cable port to use in back of time capsule. And also it is asking for password. Have tried all of mine and it will not work.

Want to us my time capsule model A1409 as only backup. 2 TB hard drive.
Already have Verizon wireless router. Do not want to use Time capsule as router, only back up for iMac.
Do not know which cable port to use in back of time capsule to Ethernet port back of my iMac.
And also it is asking for password for the server John Garland's Time Capsule so Time machine can access it..
Have tried all of passwords can think of and none work.
Held the reset button for one second on back of capsule and do not see if anything happened.
What a conundrum.
Appreciate any help to get this working.
Thanks,
John R

I have a 2TB Timecapsule and really only use it for Time Machine backups. But the Wi-Fi side is used to sync my iPad at times.
Mine is wiredup thus;
Eth cable from iMac to modem (not the WAN port should you have one), then eth cable from modem to T/Cap in the WAN port (bottom port with an O sign above it)
I believe when its connected up you may have to set up a wireless network. Follow the instructions to set up Wi-Fi and Network
and then give it a password. The WiFi icon should appear in the menu bar where you can switch it on or off.
Its been sometime since I set it with the help of Apple Techs so I might be a bit rusty.
Alan

Trying to connect Verizon wireless router to Airport Extreme but error says Ethernet unplugged.

Trying to connect Verizon wireless router to Airport Extreme and error says Ethernet Unplugged.

So, AirPort Utility running on the Windows Vista desktop can "see" the AirPort Extreme and displays its icon, but gives that error message at some point in the setup process? How far does it get?
Other questions that may help me (or somebody else) understand your problem better:
Which of the pieces were verified as working before the introduction of the AirPort Extreme?
Did you have the desktop computer attached to the Verizon GT704WGB with one of the Ethernet cables you are now trying to use? Which one? Have you tried the other one to be sure it also works?
Are you using the same port on the GT704WGB? Have you tried another one?
If the desktop has multiple ethernet ports, are you using the same one?
Had you done any special configuration of the ethernet port on the Verizon GT704WGB to get it to work with your desktop?
What category ethernet cable are you using? 3? 5? 5e? 6?

I want a new and more powerful (non-Apple) wireless router but I still want to use my existing Time Capsule to continue with my Time Machine backups and I still need the Time Capsule's Network Attached Storage (NAS) features and capabilities

THE SHORTER STORY
My goal is to successfully use my existing Time Capsule (TC) with a new and more powerful wireless router. I need a new and more powerful wireless router in order to reach a distant Denon a/v receiver that is physically located in a master bedroom some 50 feet away from my modem. I need to provide this Denon a/v receiver with an Internet connection so that it can obtain its firmware updates and I need to connect this Denon a/v receiver to my network in order to use its AirPlay feature. I believe l still need the TC's Network Attached Storage (NAS) features because I am not sure if the new wireless router will provide me with the NAS like features / capabilities I need to share files between my two Apple laptops with OS X 10.8.2. And I know that I absolutely need my TC's seamless integration with Apple's Time Machine (TM) application in order to continue to make effortless backups of my two Apple laptops. To my knowledge nothing works with TM like Apple's TC. I also need the hard disk storage space built into the TC.
I cannot use a long wired Ethernet cable connection in this apartment and I cannot use power-line adapters. I have read that wireless range extenders and repeaters are difficult to successfully set-up and that they will reduce data speeds, especially so when incorrectly set-up. I cannot relocate my modem and/or primary base station wireless router.
In short, I want to use my TC with my new and more powerful wireless router. I need to stop using the TC to connect to the modem. However, I still need the TC for seamless TM backups. I also need to use the TC's built in hard drive for storage. And I may still need the TC's NAS capabilities to share files wirelessly between laptops because I am assuming the new wireless router will not provide NAS capabilities for OS X 10.8.2 (products like this/non-Apple products rarely seem to work with OS X 10.8.2/Macs to provide NAS features and capabilities). Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone please advise on how to set-up my new Asus wireless router with my existing TC in such a way to accomplish all of this?
What is the best configuration or set-up to accomplish my above goals?
Thank you in advance for your assistance!!!
THE FULL STORY
I live in an apartment building where my existing Time Capsule (TC) is located in my living room and serves many purposes. Specially, my TC is at least all of the following:
(1) Wi-Fi router connected to Comcast Internet service via Motorola SB6121 cable modem - currently the TC is the Wi-Fi base station that connects to the modem and has the gateway address to the Internet. The TC now provides the DHCP service for the Wi-Fi network.
(2) Wireless router providing Internet and Wi-Fi network access to several Wi-Fi clients - two Apple laptop computers, an iPod touch, an iPad and an iPhone all connect wirelessly to the Internet via the TC.
(3) Wired Ethernet router providing Internet and Wi-Fi network access to three different devices - a Panasonic TV, LG Blu-Ray player and an Apple TV each use one of the three LAN ports on the back of the TC to gain access to the Internet.
(4) Primary base station in my attempt to extend my wireless network to a distant (located far away) Denon a/v receiver requiring a wired Ethernet connection - In addition to the TC, which is my primary base station, I am also using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. I cannot use a wired Ethernet connection to continuously travel from the living room to the master bedroom. The distance is too great as I cannot effectively hide the Ethernet cable in this apartment.
(5) Time Machine (TM) backup facilitator - I use my TC to wirelessly back-up two Apple laptops using Apple's Time Machine (TM) application. However, I ran out of storage space on my TC and therefore added external storage to it. Specifically, I added an external hard drive to my TC via the USB port on the back of the TC. I now use this added external hard drive connected to the TC via USB as the destination storage drive for my TM back-ups. I have partitioned the added external hard drive, and each of the several partitions all have enough storage space (e.g., each of the two partitions used by TM are sized at three times the hard drive space of each laptop, etc.). Everything works flawlessly.
(6) Network Attached Storage (NAS) - In addition to using the TC's Network Attached Storage (NAS) capabilities to wirelessly back-up two Apple laptops via TM, I also store other additional files on both (A) the hard drive built into the TC and (B) the additional external hard drive connected to the TC via USB (there are additional separate partitions on this drive for these other additional and non-TM backup files).
I use the TC's NAS feature with my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Again, everything works wirelessly and flawlessly. (Note: the Apple TV is connected to the network via Ethernet and a LAN port on the back of the TC).
The issue I am having is when I try to listen to music via Apple's AirPlay in the master bedroom. This master bedroom is located at a distance of two rooms away from the TC's current location in the living room, which is a distance of about 50 feet. This apartment has a long rectangular floor plan where each room is connected to the next in a straight line. In order to use AirPlay in the master bedroom I am using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. This additional base station connects wirelessly to the WiFi network provided by my TC and then gives my Denon receiver the wired Ethernet connection it needs to use AirPlay. I have tried moving my iTunes music directly onto my laptop's hard drive, and then I used AirPlay on this same laptop to connect to the Denon receiver. I always get a successful connection and the song plays, but the problem is that the connection inevitably drops.
I live in an apartment building and all of the many wireless routers in this building create a great deal of WiFi interference on both the 2.4 GHz and 5GHz bands. I have tried connecting the Netgear product to each the 2.4 and 5 GHz bands, but neither band can successfully maintain a wireless connection between the TC and the Netgear product. I also attempted to maintain a wireless connection to an iPod touch using the 2.4 GHz band and AirPlay on this iPod touch to play music on the Denon receiver. Again, I was able to establish a connection and successfully play music, but after a few minutes the connection dropped and the music stopped playing. I therefore have concluded that I have a poor wireless connection in the master bedroom. I can establish a connection, but it is intermittent with frequent drops. I have verified this with both laptops by working in the master bedroom for an entire day on both laptops. The Internet connection in this master bedroom proved to drop out frequently - about once an hour with the laptops. The wireless connection and the frequency of its dropout are far worse with the iPod touch and an iPhone.
I cannot relocate the TC. Also, this is an apartment and I therefore cannot extend the range of my network with Ethernet cable (I cannot drill through walls/ceilings, etc.). It is an old building with antiquated wiring and power-line adapters are not likely to function properly, nor can I spare the direct power outlet required with a power-line adapter. I simply need every outlet I can get and cannot afford to block any direct outlet.
My solution is to use a more powerful wireless router. I found the ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router which will likely provide a better connection to my wireless Internet in the master bedroom than the TC. The 802.11ac band of this Asus wireless router is totally useless to me, but based on what I have read I believe this router will provide a stronger connection at greater distances then my TC. And I will be ready for 802.11ac when it becomes more widely available.
However, I still need to maintain the TC's ability to work seamlessly with TM to backup my two laptops. Also, I doubt the new Asus router will provide OS X 10.8.2 with NAS like features and capabilities. Therefore, I still would like to use the TC's NAS capabilities to share files on my network wirelessly assuming the Asus wireless router fails to provide this feature. I need a new and more powerful wireless router, but I need to maintain the TC's NAS features and seamless integration with TM. Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone advise on how to set-up my existing TC with this new Asus wireless router in such a way to accomplish all of this?
Modem
Motorola SB6121 SURFboard DOCSIS 3.0 Cable Modem
Existing Wireless Router and Primary Wi-Fi Base Station - Apple Time Capsule
Apple Time Capsule MC343LL/A 1TB Sim DualBand (purchased June 2010, likely the Winter 2009 Model)
Desired New Wireless Router and Primary Wi-Fi Base Station - Non-Apple Asus
ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router
Extended Wi-Fi Base Station - Provides an Ethernet Connection to a Denon A/V Receiver Two Rooms Away from the Modem
Netgear Universal Dual Band Wireless Internet Adapter for TV & Blu-Ray (WNCE3001)
Addition External Hard Drive Attached to the Existing Apple Time Capsule via USB
WD My Book Studio 4TB Mac External Hard Drive Storage USB 3.0
Existing Laptops on the Wireless Network Requiring Time Machine Backups
MacBook Air (11-inch, Mid 2012) OS X 10.8.2
MacBook Pro (13-inch Mid 2010) OS X 10.8.2
Other Existing Apple Products (Clients) on the Wireless Network
iPod Touch (second generation) is model A1288.
iPad (1st generation)
Apple TV (3rd generation) - Quantity two (2)

Thanks Bob Timmons.
In regards to a Plan B, I hear ya brother. I am already on what feels like Plan Z. Getting WiFi to a far off room in an apartment building crowded with WiFi routers is a major pain.
I am basing my thoughts on the potential of a new and more powerful router reaching the far off master bedroom based on positive reviews on cnet.com, pcmag.com and pcworld.com. All 3 of these web sites have reviewed the Asus RT-AC66U 802.11AC wireless router as well as its virtual twin cousin 802.11n router. What impressed me is that all 3 sites rated this router #1 overall in terms of both range and speed (in both the 802.11n and 802.11AC flavors). They tested the router in real world scenarios where the router needed to compete with a lot of other wireless routers. One of the sites even buried this Asus router in a media room with thick walls and inside a media cabinet. This Asus router should be able to serve my 2.4 GHz band wireless clients (iPod Touch and iPhone 4) with a 2.4GHz Wireless-N band offering some 50 feet of dependable range and a 60 Mbps throughput at that range. I am hoping that works, but it's borderline for my master bedroom. My 5 GHz wireless clients (laptops) will enjoy a 5GHz Wireless-N band offering 150 feet of range and a 200 Mbps throughput at that range. I have no idea what most of that stuff means, but I did also read that Asus could reach 300 feet and I got really excited. My mileage may vary of course and I'm sure I'm making some mistakes in my interpretation of their data. However, my Winter 2009 Time Capsule was rated by cnet.com to deliver real world performance of less than that, and 802.11AC may or may not be useful to me someday. But when this Asus arrives and provides anything other than an excellent and consistent wireless signal without drops in the master bedroom it's going right back!
Your solution sounds great, but I have some questions. I'm using OS X 10.8.2 and Airport Utility (version 6.1 610.31) and on its third tab labeled "Wireless" the top option enables you to set "Network Mode" to either:
Create a wireless network
Extend a wireless network
Off
Given your advice to "Turn off the wireless on the TC," should I set Network Mode to Off? Sorry, I'm clueless in regards to how to turn off the wireless on the TC any other way. Can you provide specific steps on how to turn off the wireless on the TC? If what I wrote is correct then what should the rest of this Wireless tab look like, or perhaps it is irrelevant when wireless is off?
Next, what do you mean by "Configure the TC in Bridge Mode?" Under Airports Utility's fourth tab labeled "Network" the top option "Router Mode" allows for either:
DHCP and Nat
DHCP Only
Off (Bridge Mode)
Is your advice to Configure the TC in Bridge Mode as simple as setting Router Mode to Off (Bridge Mode)? If yes, then what should the rest of this "Network" tab look like? Anything else involved in configuring the TC in Bridge Mode or is it really as simple as setting the Router Mode to "Off (Bridge Mode)"?
How about the other tabs in Airport Utility, can they all stay as is assuming I use the same network name and password for the new Asus wireless router? Or do I need to make any other changes to the TC via Airport Utility?
Finally, in regards to your Plan B suggestion. I agree. But do you have a Plan B for me? I would greatly appreciate any alternative you could provide. Specifically, if you needed a TC's Internet connection to reach a far off corner of your home how would you do it? In the master bedroom I need both a wired Ethernet connection for the Denon a/v receiver and wireless Internet connection for the iPhone and iPod Touch.
Power-Line Adapters - High Cost, Blocks at Least One Wall Outlet and Does Not Solve the Wireless Need
I actually like exactly one power-line adapter, which is the D-Link DHP-540 PowerLine AV 500 4-Port Gigabit Switch. This D-Link power-line adapter plugs into your wall outlet with a normal sized plug (regular standard power cord much like any other electronic device) instead of all of the other recommended power-line adapters that not only use at least one wall outlet but also often block the second outlet. You cannot use a power strip with a power-line adapter which is very impractical for me. And everything about my home is strange and upside down. The wiring here is a disaster and I don't have faith in its ability to carry Internet access from the living room to the master bedroom. And this D-Link power-line adapter costs $90 each and I need at least two to make the connection to the Denon A/V receiver. So, $180 on this solution and I still don't have a dependable drop free wireless connection in the master bedroom. The Denon might get its Ethernet Internet connection from the power-line adapter, but if I want to use an iPhone 4 or iPod Touch to stream AirPlay music to the Denon wirelessly (Pandora/iTunes, etc.) from the master bedroom the wireless connection will not be stable in there and I've already spent $190 on just the two power-line adapters needed.
Extenders / Repeaters / Wirelessly Extending the Wireless Network
I have also read great things about the Amped Wireless High Power Wireless-N 600mW Gigabit Dual Band Range Extender (Repeater) SR20000G and the My Net Wi-Fi Range Extender. The former is very powerful and the latter is easier to install. Both cost about $150 ish so similar to a new Asus router. However, everything I read about Range Extenders points to them not being very effective for a far off corner of your house wherein it's apparently hard to place the range extender in the sweet spot where it both gets a strong enough signal to actually effectively extend the wireless signal and otherwise does not reduce network throughput speeds to unacceptable speeds.
Creating a Roaming Network By Hard Wiring with Ethernet Cable - Wife Would Say, "**** No!"
Even Apple seems to warn against wirelessly extending your network (see: http://support.apple.com/kb/HT4145#) and otherwise strongly recommends a roaming network where Ethernet cable is used to connect two wireless base stations. However, I am in an apartment where stringing together two wireless base stations with Ethernet cable would have an extremely low wife acceptance factor (WAF). I cannot (both contractually and from a skill prospective) hide Ethernet wire in the walls or ceiling. And having visible Ethernet cable running from room-to-room would be unacceptable, especially to the wife.
So what is left? Do you have a Plan B for me? Thanks in advance for your help!

AEBS and TC - wired connection, same wireless network

I need some advice.
I have AEBS and TC. Currently, the connection between them is "Extend wireless network". They are located on the opposite ends of my condo. I am doing some work on my unit and I have a chance to draw an ethernet cable between them. However, I'd like both of them to be the same wireless network, so that I have good coverage in and around my unit and have good speeds for accessing NAS units on the network.
Which ports would I connect with the ethernet cable and how would I configure the wireless network?
Thank you!

Main unit has eithernet cable from LAN port that connects to WAN port of second unit.
Second unit is set up in bridge mode. You should not use "WDS" or "Extend Network" These are only for wirelessly extending the network.
The second base station should be set to a "DIFFERENT" wireless channel, however the network name and security settings should be identical to the main base station.
As long as the base stations have the same network name, roaming will work between them.
Again, they need to be set to different channels so that they don't interfere with each other.
Message was edited by: Tom Alperin

How come firefox does not remember my user name and password for the verizon wireless website ? or verizon wireless ?

how come when i log onto the verizon wireless web site to pay my bill, i have to sign my user name and password every time ? i am not getting the firefox pop up asking me if i want firefox to save my password for this site. so how do i get firefox to remember my log in information for my verizon wireless website ? thank you.

This would be verizonwireless.com, correct? Their site requests that browsers should not save information for its login form.
If you're comfortable with using bookmarklets, there's one here that should force Firefox to remember:
https://www.squarefree.com/bookmarklets/forms.html#remember_password .

AEBS and AExpress N ethernet bridge disconnects when I sleep MBP??

Hi all this is my first post but im a long time mac user having grown up in a mac house.
anyways im an it guy by profession and ive been working at this issue to no avail so I figured I might come on there and see if any of you have experienced this issue
the issue I get is that when I close/sleep my MBP it disconnects the Airport Express ethernet bridge clients
NETWORK Info
I run a small business from my home thus I have FiOS (yay 20/20) with a block of 13 static ips that i distribute via DHCP and MAC reservation to allow remote access to my network as well as keep things consistent.
I currently run cat6 from my FiOS ONT to my Airport Extreme Base Station, which i use on a strict N only in 5ghz range as my area is flooded with b/g networks but no n networks (yay again).
I recently acquired an N Airport Express to provide a wireless to ethernet bridge thus extending my network to my entertainment center (ps3 xbox etc)
(extra info: im using n here because i found that b/g limits my internet connection speeds to 7-9 mbps where as my connection is capable of 20. On my n speed network I can get my full bandwidth wirelessly, yes I know there is obviously some bandwidth and throughput loss by going wireless but not as much as a b/g network was giving me)
NETWORK SETTINGS
On my n network I distribute a range of IP addresses from my static block. I have tried a few different dhcp lease times which definitely improved my initial problem which seemed that it would log me out when the key rotated every 20 min. Currently ive bumped that up to 1 day (i know not as secure id like to set it back to 20min but it seems that when it rotates that it logs me out) and haven't had that specific issue revolving around key rotation again. ive tried the WDS, Extend a network and join a network options with no real difference in behavior when I shut my laptop and for example my GF is playing rock-band online she gets disconnected also worth noting that it seems there is an intermittent DNS issue on the express ie cant find time server even though at that time ethernet clients are able to connect and get dns response
Below is my log from my express base station when the disconnect occurs
Feb 05 06:23:29 Severity:5 Clock synchronized to network time server time.apple.com (adjusted +0 seconds).
Feb 05 07:23:29 Severity:5 Clock synchronized to network time server time.apple.com (adjusted +0 seconds).
Feb 05 08:23:29 Severity:5 Clock synchronized to network time server time.apple.com (adjusted +0 seconds).
Feb 05 09:23:30 Severity:5 Clock synchronized to network time server time.apple.com (adjusted -1 seconds).
Feb 05 09:28:36 Severity:5 Joined BSS 00:1e:52:78:bc:48
Feb 05 09:28:36 Severity:5 Installed unicast CCMP key for authenticator ******:bc:48
Feb 05 10:24:05 Severity:3 No Address for NTP server time.apple.com.
Feb 05 11:24:35 Severity:3 No Address for NTP server time.apple.com.
Feb 05 12:25:05 Severity:3 No Address for NTP server time.apple.com.
Feb 05 13:25:35 Severity:3 No Address for NTP server time.apple.com.
Feb 05 14:26:05 Severity:3 No Address for NTP server time.apple.com.
Feb 05 15:26:35 Severity:3 No Address for NTP server time.apple.com.
Feb 05 15:44:34 Severity:5 Disconnected from network.
Feb 05 15:44:42 Severity:5 Joined BSS **********bc:48
Feb 05 15:44:42 Severity:5 Installed unicast CCMP key for authenticator ********bc:48
Feb 05 15:53:26 Severity:5 Connection accepted from [************:6baf%bridge0]:51073.
Feb 05 15:53:28 Severity:5 Connection accepted from [************:6baf%bridge0]:51075.
Feb 05 15:53:28 Severity:5 Connection accepted from [************6baf%bridge0]:51076.
Feb 05 16:09:13 Severity:5 Clock synchronized to network time server time.nist.gov (adjusted +0 seconds).
and my log from my AEBS
Feb 05 09:09:08 Severity:5 Clock synchronized to network time server time.nist.gov (adjusted +0 seconds).
Feb 05 09:28:37 Severity:5 Associated with station ******:91:07
Feb 05 09:28:37 Severity:5 Installed unicast CCMP key for supplicant **********:91:07
Feb 05 10:09:09 Severity:5 Clock synchronized to network time server time.nist.gov (adjusted +0 seconds).
Feb 05 11:09:10 Severity:5 Clock synchronized to network time server time.nist.gov (adjusted -1 seconds).
Feb 05 12:09:10 Severity:5 Clock synchronized to network time server time.nist.gov (adjusted +0 seconds).
Feb 05 13:09:11 Severity:5 Clock synchronized to network time server time.nist.gov (adjusted -1 seconds).
Feb 05 14:09:11 Severity:5 Clock synchronized to network time server time.nist.gov (adjusted +0 seconds).
Feb 05 14:15:28 Severity:5 Associated with station ******:6b:af
Feb 05 14:15:28 Severity:5 Installed unicast CCMP key for supplicant ******6b:af
Feb 05 15:09:13 Severity:5 Clock synchronized to network time server time.nist.gov (adjusted -2 seconds).
Feb 05 15:44:32 Severity:5 Disassociated with station ******6b:af
Feb 05 15:44:35 Severity:5 Rotated CCMP group key.
Feb 05 15:44:35 Severity:5 Deauthenticating with station ******cc:e5 (reserved 2).
Feb 05 15:44:35 Severity:5 Disassociated with station ******:cc:e5
Feb 05 15:44:35 Severity:5 Disassociated with station ******91:07
Feb 05 15:44:36 Severity:5 Rotated CCMP group key.
Feb 05 15:44:43 Severity:5 Associated with station ******:cc:e5
Feb 05 15:44:43 Severity:5 Installed unicast CCMP key for supplicant ******cc:e5
Feb 05 15:44:44 Severity:5 Associated with station ******91:07
Feb 05 15:44:44 Severity:5 Installed unicast CCMP key for supplicant ******91:07
Feb 05 15:53:01 Severity:5 Associated with station ******6b:af
Feb 05 15:53:01 Severity:5 Installed unicast CCMP key for supplicant ******:6b:af
Feb 05 15:53:15 Severity:5 Connection accepted from [******:6baf%bridge0]:51048.
Feb 05 15:53:16 Severity:5 Connection accepted from [******6baf%bridge0]:51049.
Feb 05 15:53:16 Severity:5 Connection accepted from [******:6baf%bridge0]:51050.
Feb 05 16:09:13 Severity:5 Clock synchronized to network time server time.nist.gov (adjusted +0 seconds).
THANKS FOR YOUR INPUT AND SUGGESTIONS

i decided to also add my log from the mbp (dont think it matters but its an early 2008 model mbp)
as you can see i put my computer to sleep at the exact same time that the airport express lost connection iI
2/5/09 3:44:31 PM kernel hibernate image path: /var/vm/sleepimage
2/5/09 3:44:31 PM kernel sizeof(IOHibernateImageHeader) == 512
2/5/09 3:44:31 PM kernel Opened file /var/vm/sleepimage, size 4294967296, partition base 0xc805000, maxio 400000
2/5/09 3:44:31 PM kernel hibernate image major 14, minor 2, blocksize 512, pollers 4
2/5/09 3:44:31 PM kernel hibernateallocpages flags 00000000, gobbling 0 pages
2/5/09 3:44:32 PM kernel /drv/ MacModule.cpp:261 powerStateWillChangeTo: flags=4 stateNumber=2
2/5/09 3:44:32 PM configd[36] AppleTalk shutdown
2/5/09 3:52:59 PM kernel /drv/ MacModule.cpp:266 powerStateWillChangeTo: found flag=kIOPMSleepCapability (4)
2/5/09 3:44:32 PM configd[36] AppleTalk shutdown complete
2/5/09 3:52:59 PM kernel AirPort: Link Down on en1
2/5/09 3:52:59 PM aosnotifyd[278] Stream:streamCallback - an error occurred on CFReadStream: Operation could not be completed. Socket is not connected
2/5/09 3:52:59 PM kernel /drv/ MacModule.cpp:261 powerStateDidChangeTo: flags=4 stateNumber=2
2/5/09 3:52:59 PM kernel /drv/ MacModule.cpp:266 powerStateDidChangeTo: found flag=kIOPMSleepCapability (4)
2/5/09 3:52:58 PM configd[36] setting hostname to "Comp.local"
2/5/09 3:44:34 PM kernel System SafeSleep
2/5/09 3:52:59 PM kernel hibernatepage_listsetall start
2/5/09 3:52:59 PM kernel hibernatepage_listsetall time: 180 ms
2/5/09 3:52:59 PM kernel pages 635428, wire 220619, act 232958, inact 31, zf 59, throt 1114, could discard act 55989 inact 111080 purgeable 13578
2/5/09 3:52:59 PM kernel hibernatepage_listsetall found pageCount 454781
2/5/09 3:52:59 PM kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
2/5/09 3:52:59 PM kernel IOHibernatePollerOpen(0)
2/5/09 3:52:59 PM kernel writing 454552 pages
2/5/09 3:52:59 PM kernel image1Size 636423168
2/5/09 3:52:59 PM kernel all time: 21548 ms, comp time: 2872 ms, deco time: 0 ms,
2/5/09 3:52:59 PM kernel image 1120299008, uncompressed 1861844992 (454552), compressed 1116586684 (59%), sum1 5d386928, sum2 eeca85bd
2/5/09 3:52:59 PM kernel hibernatewriteimage done(0)
2/5/09 3:52:59 PM kernel sleep
2/5/09 3:52:59 PM kernel Wake reason = EC LID0
2/5/09 3:52:59 PM kernel System Wake

Help with Verizon Router and Setting Up a Second Wireless Router

I had my network set up until I had intermittent loss of the internet. So I received a new Verizon router and I cannot figure out how to use the second wireless router which I used to have working just fine.
The new Verizon router is the Actiontec MI424WR and it is installed in my basement and the signal is weak. However there is a cat5 wire snaked up from the Actiontec router to my home office. Currently that is plugged into the back of my computer for internet acess. My second router is the Trendnet 300Mbps Wireless N Home router. ANd this is the router that I would like to use (and used to use) to trasmit the internet connection throughout the house as well as use for a wired connection to my home security system.
I attempted to plug the cat5 wire from the Actiontec into the back of the Nextrend router (1,2,3,4 and not the WAN) but then would lose the internet signal whether I attempted to log on via wired or wireless. Must be some kind of settings I need to change.
Can anyone help me to understand how to add the second router? I am relatively computer literate but cannot understand the instructions from Verizon. Thanks in advance.
Solved!
Go to Solution.

I point you to http://www.dslreports.com/faq/12506
If you have any questions, please ask.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Verizon Wireless Router

I currently have verizon DSL using there Westell router. However I am looking to upgrade to a wireless router. Does Verizon offer a
free upgrade or if that is not possible can anyone tell me a good wireless router to get??? I have tried calling verizon direct but
actually talking to someone is almost impossible.

If you have the Westell 6100 and you add another router, do not forget to follow..
URL: http://www.dslreports.com/faq/13600
Title/Location: All DSLR (dslreports.com) FAQs » Verizon Online DSL FAQ » Hardware » How do I use a router with the Westell 6100?
^^
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Use wireless router with existing network and switch?

I have an existing network using a T1 into a switch; all the computers and the server are connected to the switch. Some distance away, via ethernet cable to the switch, I would like to connect a wireless router, one computer wired to that router, and other computers connect via wireless. Our server provides DHCP. Is this possible? How best to do it? Which Linksys router would be best for the purpose? Thanks for the help!

The "correct" device to use would be a wireless access point like the Linksys WAPs and not a WRT router. WRT routers are supposed to connect to the internet on its own.
You can set up a WRT router as simple access point. see here for the setup.
The best router is the one which best suits your needs. All wireless routers and access point provide wireless access. It depends on what you want (802.11n, 11b, 11g, range, speed, etc.). The newer routers are better from the specifications but usually also have more firmware bugs. But that's pretty much all one can say based on your generic requirements.

Syncing Apple TV and iTunes by third party wireless router - solution?

I have been having lots of problems syncing my Apple TV with iTunes ever since I installed iTunes 7.6 including, Apple TV not appearing/disappearing in devices list, content not authorized, etc. I followed troubleshooting help, asked in store for advice, re-installed everything - nothing worked.
Last night I installed the new combo 10.5.2 update and still got nowhere.
However, I accidently disconnected the power to my wireless router (BT Homehub) and restarted it and iTunes recognised Apple TV and started to sync!!!
So at last I have content on my Apple TV again. Only comment is that syncing is extremely slow, but at least it's working now.
Mark

I think your problem comes from unchecking the files. Unchecking will affect all devices synced with iTunes. Likely the easiest thing to do is edit the syncing method to sync selected playlists then manage the playlist contents.

Unable to conect Original Airport Card to password protected wireless route

I am trying to connect a ClamShell notebook( OS 10.3.9) with an Apple Original Airport Card (installed) to a wireless router. When I access the network in System preferences, it detects the router and my Airport Card and indicates that a password is needed to access the that network. After inputting the password and with the location router highlighted, it does not connect me with the network as I go through the setup procedure. The system administrator successfully connected to the router with a PC laptop. Am I not selecting a topic that I should or have I not performed the set up procedure correctly? I did not have this problem when I connected to a non-password router.
Any help would be greatly appreciated,
Darrell

Never received a reply from Henry B. so I decided to experiment with my problem. I Inputted the password in the Setup assistant, highlighted the router location and clicked Continue to continue with the Assistant. The Airport icon in the top bar became more pronounced instead of faded. I did not receive confirmation of a connection, in fact the back up page button was the only button active. I closed out of the Setup Assistant. I brought a browser and found the browser was connected to the Internet.
MORAL: Don;t always believe the Setup Assistant

Setting up a Time Capsule with Verizon Wireless Router

I am trying to set up my TC with a Verizon Wiresless Router. I wish to use the TC's wiresless signal and shut off the Verizon signal (can do). I plugged the TC via ethernet, into port 2 on the verizon router and in the WAN connection on the TC. I am getting a blinking amber light. No idea where to go, I cannot access the TC via my iMac and the ethernet port on the iMac doesn't work (broken since new!) Help much appreciated. I will want to use the TC to back up the iMac and two macbooks. THANK YOU!

Ok, I found the TC on the iMac after restarting the airport utility!

Need help configuring Cisco/Linksys wireless router to extend wi-fi signal to living room

My U-verse wireless gateway is in the back of our house. We live in an old 1920's home with solid wood walls. For our macbooks, we get a pretty decent signal, but my wife's iPad 2 get's poor wi-fi speeds. I bought a Cisco/Linksys WRT160N wireless N broadband router. I have a wired connection in my living room (going to a 4 port switch) then connected to my DVR. I tried hooking up the new router but ended up getting no signal on the iPad. In fact, it caused other issues. I ended up disconnecting it and re-booting my gateway. All came back fine. This wireless router replaces a similar unit that went out in after a power failure, so I know this can be done, but I forget exactly how I confiured the old one. I would like it to "extend" my signal to the living room, but I am also willing to create a new network (different SSID). Do I need to turn of DHCP? Are there any web sites that can assist me in configuring the router? I wish I didn't have to deal with this. The signal from the RG is great when you are in the back room (20+ down). But my wife gets about 3 down on her iPad in the living room. Thanks in advance.

Hi ,
I was doing some research on how this can be done. It does not appear there is an option in the Cisco router to set it up as an access point, but there are several options you can do to extend your network.
The first thing you can do is just set it up as a router behind router setup, and you will just have two separate networks. Make sure the DHCP pool does not conflict with the U-verse's gateway of 192.168.1.x.
The second thing you can do is connect the Ethernet cable to one of the LAN ports on your Cisco router instead of using the internet port. This should make it work like a smart switch.
With both setups, you want to probably change the SSID, network key, and wireless security settings to the same thing for wireless roaming abilities. That way, anyone that configures their wireless connection will be connected to both networks. Just make sure the wireless channels are not the same, and I would suggest having them at least 5 apart.
Hope this helps.
-ATTU-verseCare

Conecting AEBS and AExpress to a Verizon wireless router to extend network

Similar Messages

Maybe you are looking for