Conf bridge wont register dsp farming

Hi all
Using a 2801 router and pvdm2-8.  Have successfully added and registered the Transcoder in the IOS and on CUCM (version 4) however wont allow me to add any max sessions to the conference bridge at all.  The transcoder has been given a max session of 2. Everything has been configured ok (i believe) and followed the cisco docs to double check all the router config was correct however still no joy!
Can anyone help or have any ideas?
Have attached the running config of the router.
Many thanks
Dave

Hi there,
There are some good troubleshooting tips in this excellent doc from Tony @ Cisco
https://supportforums.cisco.com/docs/DOC-9464
Cheers!
Rob
PS: one thing I'm curious about is the "version" in
sccp ccm 11.11.11.11 identifier 1 priority 1 version 7.0

Similar Messages

  • Putting PVDMs in NM-2V / VIC-2FXO / VIC-2FXS into DSP farm

    I have a Cisco 2650XM router with an NM-2V module with one VIC-2FXO and one VIC-2FXS card in it. I'm very new to Cisco voice stuff and want to get started with it. I'm trying to pool the PVDMs on this router into a DSP farm so that they can be used in CME 4.1 with call conferencing / transcoding / VoIP calls between Cisco IP Communicator and Cisco VoIP physical phones but I'm having issues doing so. I believe I'm supposed to create a DSP farm by going into "voice-card X" mode and assigning them to the DSP farm?
    I know that there are PVDMs present because they are listed when I do a "show voice dsp detail." I'm not sure if the PVDMs are present in the NM-2V module or actually on the VICs. Can someone offer advice?

    Yeah, the only cards / modules that I have in the router are the NM-2V, VIC-2FXO, and VIC-2FXS. Here is the "show diag" output as well as some other ones that may be useful.
    Press RETURN to get started!
    *Mar  1 00:00:05.949: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
    *Mar  1 00:00:25.281: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
    *Mar  1 00:00:25.970: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:25 UTC Fri Mar 1 2002 to 17:00:25 AZT Thu Feb 28 2002, configured from console by console.
    *Mar  1 00:00:26.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
    *Mar  1 00:00:27.873: %SYS-5-CONFIG_I: Configured from memory by console
    *Jan  4 02:05:04.149: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.4(15)T14, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 17-Aug-10 05:40 by prod_rel_team
    *Jan  4 02:05:04.153: %SNMP-5-COLDSTART: SNMP agent on host KINASE is undergoing a cold start
    *Jan  4 02:05:04.322: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
    *Jan  4 02:05:04.322: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
    *Jan  4 02:05:05.435: %LINK-3-UPDOWN: Interface Foreign Exchange Office 1/0/0, changed state to up
    *Jan  4 02:05:05.435: %LINK-3-UPDOWN: Interface Foreign Exchange Office 1/0/1, changed state to up
    *Jan  4 02:05:05.439: %LINK-3-UPDOWN: Interface Foreign Exchange Office 1/1/0, changed state to up
    *Jan  4 02:05:05.439: %LINK-3-UPDOWN: Interface Foreign Exchange Office 1/1/1, changed state to up
    CNF-FILES: Clock is not set or synchronized, retaining old versionStamps
    CNF files update complete (post init)
    KINASE>en
    KINASE#show diag
    Slot 0:
    C2650XM 1FE Mainboard Port adapter, 1 port
    Port adapter is analyzed
    Port adapter insertion time unknown
    EEPROM contents at hardware discovery:
    Hardware Revision        : 3.0
    PCB Serial Number       FFFF
    Part Number              : 73-7755-04
    RMA History              : 00
    RMA Number               : 0-0-0-0
    Board Revision           : A0
    Deviation Number         : 0-0
    Product (FRU) Number     : C2650XM-1FE
    EEPROM format version 4
    EEPROM contents (hex):
      0x00: 04 FF 40 03 6E 41 03 00 C1 0B FF FF FF 46 46 46
      0x10: 46 FF FF FF FF 82 49 1E 4B 04 04 00 81 00 00 00
      0x20: 00 42 41 30 80 00 00 00 00 FF FF FF FF FF FF FF
      0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
      0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
      0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
      0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
      0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
    Slot 1:
    4 PORT Voice PM for C2600 Port adapter
    Port adapter is analyzed
    Port adapter insertion time unknown
    EEPROM contents at hardware discovery:
    Hardware revision 1.1                   Board revision H0
    Serial number     26333860            Part number    800-02491-02
    FRU Part Number     NM-2V=           
    Test history      0x0                   RMA number     00-00-00
    EEPROM format version 1
    EEPROM contents (hex):
      0x00: 01 65 01 01 01 91 D2 A4 50 09 BB 02 00 00 00 00
      0x10: 88 00 00 00 01 06 27 17 FF FF FF FF FF FF FF FF
      0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
      0x30: FF FF FF FF FF FF FF FF FF FF FF FF
    VIC Slot 0:
    FXO Voice daughter card (2 port)
    Hardware revision 1.1                   Board revision J0
    Serial number     21522658            Part number    800-02495-01
    Test history      0x0                   RMA number     00-00-00
                                      Connector type    Wan Module
    EEPROM format version 1
    EEPROM contents (hex):
      0x20: 01 0D 01 01 01 48 68 E2 50 09 BF 01 00 00 00 00
      0x30: 98 00 00 00 00 07 22 01 FF FF FF FF FF FF FF FF
    VIC Slot 1:
    FXO Voice daughter card (2 port)
    Hardware revision 1.1                   Board revision J0
    Serial number     22783161            Part number    800-02495-01
    Test history      0x0                   RMA number     00-00-00
                      Connector type    Wan Module
    EEPROM format version 1
    EEPROM contents (hex):
      0x20: 01 0D 01 01 01 5B A4 B9 50 09 BF 01 00 00 00 00
      0x30: 98 00 00 00 00 11 16 01 FF FF FF FF FF FF FF FF
    KINASE#sh voice dsp detail
    DSP  DSP                DSPWARE CURR  BOOT                         PAK     TX/RX
    TYPE NUM CH CODEC       VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT
    ==== === == ======== ========== ===== ======= === == ========= == ===== ============
    C542 001 01 None          9.4.7 IDLE  idle      0  0 1/0/0     NA     0      602/623
    C542 002 01 None          9.4.7 IDLE  idle      0  0 1/0/1     NA     0      593/590
    C542 003 01 None          9.4.7 IDLE  idle      0  0 1/1/0     NA     0      601/622
    C542 004 01 None          9.4.7 IDLE  idle      0  0 1/1/1     NA     0      593/590
    KINASE#sh dspfarm
    DSPFARM Configuration Information:
    Admin State: DOWN, Oper Status: DOWN - Cause code: ADMIN_STATE_DOWN
    Transcoding Sessions: 0(Avail: 0), Conferencing Sessions: 0 (Avail: 0)
    Trans sessions for mixed-mode conf: 0 (Avail: 0), RTP Timeout: 600
    Connection check interval 600 Codec G729 VAD: ENABLED
    KINASE#config t
    Enter configuration commands, one per line.  End with CNTL/Z.
    KINASE(config)#voice-card ?
      <0-1>  Voice interface slot #
    KINASE(config)#voice-card 0 ?
    % Unrecognized command
    KINASE(config)#voice-card 0?
    % Unrecognized command
    KINASE(config)#voice-card 0?
    % Unrecognized command
    KINASE(config)#voice-card 0/?
    % Unrecognized command
    KINASE(config)#voice-card 0
                              ^
    % Invalid input detected at '^' marker.
    KINASE(config)#voice-card 1
                              ^
    % Invalid input detected at '^' marker.
    KINASE(config)#
    KINASE(config)#voice-port 1/0/0
    KINASE(config-voiceport)#?
    Voice-port configuration commands:
      battery-reversal     Enable FXO battery-reversal detection
      bearer-cap           Specify the bear capability
      busyout              Configure busyout trigger event & procedure
      comfort-noise        Use fill-silence option
      connection           Specify Trunking Parameters
      cptone               Configure voice call progress tone locale
      default              Set a command to its defaults
      description          Description of what this port is connected to
      dial-type            Configure type of dialer for voice
      disc_pi_off          close voice path when disconnect with PI received
      echo-cancel          Echo-cancellation option
      exit                 Exit from voice-port configuration mode
      impedance            Specifies the terminating impedance of the interface
      input                Configure input gain for voice
      music-threshold      Threshold for Music on Hold
      no                   Negate a command or set its defaults
      non-linear           Use non-linear processing during echo cancellation
      output               Configure output attenuation for voice
      playout-delay        Configure voice playout delay buffer
      pre-dial-delay       FXO Pre-dial Delay
      ring                 Number of rings
      shutdown             Take voice-port offline
      signal               The signaling type for the interface FXS or FXO
      snmp                 Modify SNMP voice port parameters
      station-id           Configure station ID
      supervisory          Configure answer + disconnect supervision options
      threshold            Threshold [noise] for voice port
      timeouts             Configure voice timeout parameters
      timing               Configure voice timing parameters
      translate            Translation rule
      translation-profile  Translation profile
      trunk-group          Configure interface to be in a trunk group
      voice-class          Set voiceport voice class control parameters
    KINASE(config-voiceport)#
    Looks like the "voice-port" command works, but not the "voice-card" command.

  • 1760 as conf bridge DSPFarm

    Hello
    I have a 1760 with DSPs in it...i would like to use it as a DSP farm for Conferencing...i setup the dspfarm parameters in the router, how do i get it to be recognized in the CCM...i went to add new IOS bridge, typed in the IP address for the name and i get nothing...any ideas?
    TIA

    Hi,
    http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgcr/vvfax_c/callc_c/ccm_c/intcnf2.htm#wp1052594
    Use Cisco IOS Conference Bridge .
    http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/4_1/sys_ad/4_1_3/ccmsys/a05confb.htm#wp1022368

  • Bridge wont recognizw my Nikon d610.  I am running windows 8 and photoshop cs6 with 8.6 camera raw plug in.  How can I get bridge to recognize my camera?  Thanks to anyone who can help!!

    Bridge wont recognizw my Nikon d610.  I am running windows 8 and photoshop cs6 with 8.6 camera raw plug in.  How can I get bridge to recognize my camera?  Thanks!!

    That camera model has been supported since ACR 8.3 and it is most certainly supported by ACR 8.6 and ACR 8.7 (beta).
    Either you have damaged, corrupt image files, or a faulty Photoshop and/or ACR installation.
    If there are no privacy issues, you can post one of your files to the FTP service of your choice (such as Dropbox or yousendit.com), post the link to it, and someone here can take a look at it for you.

  • Bridge wont open from within cs4

    I upgraded to cs4 from cs2, it works fine but bridge wont open from within cs4. I get this little window - error2:photoshop 11 is undefined. Line 1, photoshop11.invoke bridge (false,false")
    Bridge does open from windows start menu.

    What folder did you put them in? also, you need to restart Photoshop before you can see them added to the panel menu.

  • Quicktime pro 7 wont register, please help.

    hi, i just purchased quicktime pro 7 upgrade, i copied and pasted the Name and registration code from the email to the quicktime pro registration setting. but it always give s me the invalid registration code error. im using quicktime 7.0.3 atm, all i wanan do is chuck in some videos into my ipod video i jsut bought 2 days ago. please, someone tell me why it wont register? the $44.95AUS isnt cheap for a software upgrade.

    I had the same problem tried pasting the key, typing the key, same response. make sure that in the Registered To field, you enter the name EXACTLY how it appears in the Email you have received (it's the Registered Name).
    This helped me after 2 hours of installing and reinstalling the product...
    quitcktime pro   Windows XP  

  • Bridge wont open

    i rolled back from 2.0 beta to 1.0.7.3312 and now bridge wont work  i can connect to my 9900, and i even get notifications of new messages and e-mails but none of the bridge apps will open. any ideas?

    First, I'd suggest resetting the Playbook... touch the battery icon > reset.
    Or, press and hold the Volume Up + Down  + Power key (all three) simultaneously for about 10 seconds.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • My itunes wont register my ipad

    My iTunes wont register my iPad after I upgraded my iTunes and my iPad. It use too however for some reason now it wont. I've restarted my iPad and computer as well as uninstall iTunes and re-stalled again. What do I do?

    Hello DanniGill,
    Welcome to the Apple Support Communities!
    I understand that after running updates, your iPad is no longer being recognized in iTunes on your Windows computer. To troubleshoot this situation, I would recommend reading over and working through the steps located in the attached article. 
    iPhone, iPad, or iPod not recognized in iTunes for Windows - Apple Support
    Have a great day,
    Joe

  • Phone wont register saved contact name

    i own a n85 and 6500classic. the issue is it wont recall my bros names when they send or sms or call me. or either would only register one of my bros nos. my brother's nos are +63922XXXXXXX and +63917XXXXXXX. the xxxxxxx are the last 7 digits in their nos. they have both the same last 7 digits but belong to two different neworks. when one of them call me the mobile no will just display on the phone. and when they send me sms only the +63917xxxxxxx name will register eventhough +63922xxxxxxx is the one who sent the sms. i think the phones issued in the phils only recognizes the last 7 digits to register in the caller id. which should not be since ther are several networks providing service wherein there would be 2 or more people sharing the same 7digit no but having different prefix or service providers. is it solved by updating software? should it be recognizing 10 digits (service provider prefix + mobile no)?
    for example 0922abcdefg, 0919abcdefg,0917abcdefg,0918abcdefg, 0929abcdefg etc. will only be recognized as a single no and if you have these 5 different nos registered to 5 different persons the phonebook will go crazy on who to display upon sms or a call.
    somebody help me on this. you could email me thru  it is impractical for me to ask my brother to change his mobile no. since it is not good for him to change nos and update all the people he knows to update their phonebooks just because it wont register in my phone. thanks in advance.
    Moderator Note: Email address removed
    Message Edited by prodigy on 02-Oct-2009 04:43 AM

    any comments and suggestions from n85 or 6500 classic users here? thanks in advance.

  • Ipod wont register what songs i have listened to?

    i've had an ipod nano for a few years now and it work fine up until a few months ago when it froze on me. i was able to reset it and it still works but i have recently noticed that when i connect my ipod to my computer to charge it wont register want songs i have listened to (for example the play count or when it was last played) it's not much of a problem cause i can still listen to it but i was just wondering if anyone else has had this problem?

    Your sync settings may have changed. I have my ipod to NOT automatically sync and it never tells iTunes how many times I have played the song. But because I have my iPhone sync, it tells the computer how many times I listen to the songs.
    I do not know if this will help you, but it may point you in the right direction.

  • CIPC wont register

    I have CIPC 8.6 installed on Win 7 laptop using Cisco VPN into the company.  I can not get it to register.  It just keeps saying configuring IP...  
    Help needed.

    Duplicate thread - https://supportforums.cisco.com/discussion/12173766/cipc-wont-register.

  • Ipod wont register

    hi my ipod wont register
    when i get to the page saying ipod software licence agremant and click the checkbox nothing happens why is this?

    Hello Neal,
    There should be a Continue button in the lower right hand corner of the window you need to continue to continue and complete the registration process.  If you are unable to see this button, try adjusting your monitor's resolution.
    B-rock

  • Ipod touch not working at all and wont register to charge...help!!

    My son has a 4th gen. ipod touch. He had it on sleep mode for an hour and now it isnt working at all. It wont turn on and it wont register when we try to charge it. Any suggestions on whats wrong with it??

    READ THE WHOLE ARTICLE!!!
    Hi there have a simple answer that works(i did it on my friends iPod touch 4 gen)
    Plug the iPod into your sons iPod doc or wall adapter ...NOT PC OR MAC... And hold the sleep and menu button for THIRTY seconds.... This will wipe the iPod clear and will also leave it blank then do not use it at all in anyway shape or form. Wait for ios5 to come out( October the 12th 2011) and then Plug it into your PC or Mac that you originally had it synced with and it will work

  • 6th gen nano wont register on itunes

    My ipod suddenly wont register on itunes.  Why?

    Hello Riley86,
    I would try this:
    iPod not recognized in 'My Computer' and in iTunes for Windows
    Make sure you go through EACH step. Normally one of them works.
    Hope this helps.
    ~Julian

  • HT1267 MY 3GS HAS NO SERIAL OR IMEI NUMBER ON SIM CARRIER,it wont register any sim, the sim carrier is plastic

    my 3gs wont register sim card when inserted, and i cannot open it in itunes

    iPhone: Locating the serial number, IMEI, ICCID, or MEID
    How to find the serial number of your Apple hardware product
    iPhone: Hardware troubleshooting

Maybe you are looking for