Conference call.. what does this mean

I accepted a call from a friend and i was looking through the call logs and scrolled through the history and it said that call was a 'conference call'. What does this mean.
I'm used to seeing 'placed call, missed call, received call"

A conference call is a call between three or more people. Your friend may have inadvertently hit the conference call feature and only added you to the call or it is possible there was a third person listening in.
~Lorrie~ Master of All Things Blackberry!

Similar Messages

Images have ? symbol on the top right corner of the thumbnail what does this mean and how do I remove it?

Q - My images have a
? symbol on the top right corner of the thumbnail what does this mean and how do I remove it?
A - The
? symbol is used to identify a file that Lightroom can no longer access; probably because it has been moved using OS drag/drop or Move command rather than Lightroom.
Click the
? symbol will cause a small dialog will appear. This dialog will provide information as to where the file was originally located along with an option to find (Locate) it again.
As you'll quickly realise, clicking the
? symbol is fine for finding individual files that may have been relocated, but not for large numbers. There must be a better way
Look at the Folder panel (left side of Library module) and you should find that the folder/subfolder containing the files that Lightroom can no longer find are shown in Red text. It is the red text that Lightroom uses to help you identify a folder/subfolder that contains files that it has lost track off.
On the Mac you should
Ctrl-click (right-click when using two button mouse) the folder/subfolder, a pop-up menu will appear. From the pop-up menu choose the command
Locate Missing Folder, a dialog should appear. The dialog gives you access to every hard disk connected to your computer or CD/DVDs if they're in the tray. Use this dialog to navigate to the location where the folder is now located, then select this folder (not the files). Finally, press the
Choose button and allow Lightroom to do its stuff.
The method described above also applies to the PC version although the dialog is called
Browse for Folder and the
Choose button is replaced by
OK.
You can avoid getting into a situation were Lightroom looses track of your folders/subfolders by using a variation of above.
A tutorial demonstrating above can be found
Here

Q - My images have a
? symbol on the top right corner of the thumbnail what does this mean and how do I remove it?
A - The
? symbol is used to identify a file that Lightroom can no longer access; probably because it has been moved using OS drag/drop or Move command rather than Lightroom.
Click the
? symbol will cause a small dialog will appear. This dialog will provide information as to where the file was originally located along with an option to find (Locate) it again.
As you'll quickly realise, clicking the
? symbol is fine for finding individual files that may have been relocated, but not for large numbers. There must be a better way
Look at the Folder panel (left side of Library module) and you should find that the folder/subfolder containing the files that Lightroom can no longer find are shown in Red text. It is the red text that Lightroom uses to help you identify a folder/subfolder that contains files that it has lost track off.
On the Mac you should
Ctrl-click (right-click when using two button mouse) the folder/subfolder, a pop-up menu will appear. From the pop-up menu choose the command
Locate Missing Folder, a dialog should appear. The dialog gives you access to every hard disk connected to your computer or CD/DVDs if they're in the tray. Use this dialog to navigate to the location where the folder is now located, then select this folder (not the files). Finally, press the
Choose button and allow Lightroom to do its stuff.
The method described above also applies to the PC version although the dialog is called
Browse for Folder and the
Choose button is replaced by
OK.
You can avoid getting into a situation were Lightroom looses track of your folders/subfolders by using a variation of above.
A tutorial demonstrating above can be found
Here

Given filename or path contains Unicode or double-byte characters.Retry using ASCII characters for filename and path What does this mean? it happen when I publish an OAM

Given file name or path contains Unicode or double-byte characters. Retry using ASCII characters for filename and path
What does this mean? It is happening when I try to publish an OAM for Dreamweaver.
Also: How can I specify the browser in Edge Animate? It is just going wherever. Are there no Preferences for Edge Animate?
BTW. Just call it Edge. Seriously. Do you call it Illustrator Draw? Photoshop Retouching?

No, my file name is mainContent.oam
My project name is mainContent.an
This error happens when I try to import into Dreamweaver. Sorry, I wasn't clear on that earlier.
I thought maybe it was because I had saved my image as a png. So re-saved as a svg, still get the error.
DO I have a setting is Dreamweaver CC that is wrong? Should I try this in Dreamweaver CS6? I might try that next.
Why is this program so difficult? I know Flash. I know After Effects. I can work the timeline part just great. It's always in the export that I have problems.
On a MacPro, 10.7.
Are you an Adobe person or just a nice helper?

What does this mean ---- load-on-startup 1 /load-on-startup

Hi All,
Anybody please tell me what does this mean:
<load-on-startup>1</load-on-startup>
Thanks in advance
amitindia

From the dtd :
The load-on-startup element indicates that this servlet should be
loaded (instantiated and have its init() called) on the startup
of the web application. The optional contents of
these element must be an integer indicating the order in which
the servlet should be loaded. If the value is a negative integer,
or the element is not present, the container is free to load the
servlet whenever it chooses. If the value is a positive integer
or 0, the container must load and initialize the servlet as the
application is deployed. The container must guarantee that
servlets marked with lower integers are loaded before servlets
marked with higher integers. The container may choose the order
of loading of servlets with the same load-on-start-up value.

Panic! What does this mean???? help

Hi,
My macbookpro is just 3 weeks old and I already had 3 panics.....
Here is the log file for one of the event:
Mon May 28 18:34:45 2007
panic(cpu 1 caller 0x0035DF18): mbuf address out of range 0x1183000
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x14203b68 : 0x128d08 (0x3cb134 0x14203b8c 0x131de5 0x0)
0x14203ba8 : 0x35df18 (0x3eb8f4 0x1183000 0x144eb78 0x206)
0x14203be8 : 0x23ab46 (0x25b70100 0x0 0x1e2 0x1)
0x14203cf8 : 0x23ed3a (0x2b8e394 0x25b70100 0x1 0x1e2)
0x14203d38 : 0x361033 (0x2b8e16c 0x0 0x25b70100 0x0)
0x14203dd8 : 0x35342d (0x2b8e16c 0x0 0x14203e9c 0x25b70100)
0x14203e08 : 0x34f370 (0x3478dd0 0x14203e9c 0x2d89004 0x0)
0x14203ef8 : 0x34f604 (0x3663dac 0x3478dd0 0x33 0x13a11930)
0x14203f58 : 0x379e23 (0x3663dac 0x2ff3cb8 0x2ff3cfc 0x0)
0x14203fc8 : 0x19b17e (0x2eb2900 0x0 0x19e0b5 0x2eb2ac0) No mapping exists for frame pointer
Backtrace terminated-invalid frame pointer 0xb019f558
Kernel version:
Darwin Kernel Version 8.9.1: Thu Feb 22 20:55:00 PST 2007; root:xnu-792.18.15~1/RELEASE_I386
What does this mean?
Is there a fix?
Thank you.
Fred

fredericlang,
Your plan sounds good to me, and yes, there could be some "intermittent" hardware failure causing the panics.
Before we go on, I want to establish that you should NEVER have a panic, provided you have three things:
1) Flawless hardware
2) A flawless installation (which is why we are "zeroing" and reinstalling)
3) No bad or conflicting kernel extension
To back this up, I will tell you that I have only had one KP on this machine, it was long ago, and it was due to a disk error (and thus a bad installation). Currently, my "uptime" is at 44 days, 13 1/2 hours, and I put this thing through its paces every day.
OK, well a 4th thing: Problematic peripherals.
Let's rule these out, one by one. Are you connecting anything that could cause panics, or is anything connected when they occur? No? Let's move on.
We are pretty sure we have ruled out a bad installation, and you are going to make double sure. Good.
Are you installing any third-party "haxies," or anything else that might place kernel extensions in the Extensions folder? Are you running the Migration Assistant to transfer stuff from a PPC machine? If you can rule this last one out, we are left with only one possibility...
HARDWARE! As I say, you should never have a single kernel panic. If you have narrowed it down to hardware, and they still occur, be firm! Insist, regardless of the results of any diagnostics, that you have a new machine, or a logic board/memory replacement. If necessary, escalate your case. Get this fixed, and get it fixed expeditiously.
Scott

When I try to turn on Home Sharing, I get the message: "Home Sharing could not be turned on because of an error (5506)." What does this mean please?!

When I try to turn on Home Sharing, I get the message: "Home Sharing could not be turned on because of an error (5506)." What does this mean please?!

I had the same error it was due to a program called Little Snitch, it's somewhat like a firewall. I changed the settings in Little Snitch to allow network connections in iTunes and now I can enable Home Sharing. Maybe you should try changing some firewall settings.

My Power Mac G4 booted from an OS 9.1 install CD, and then froze up. Now I turn the machine on, beeps 3 times, power button blinks 3 times. What does this mean?

I tried to install Mac OS 9.1. I turned the computer on, heard the bong noise (although with some static), and inserted the OS 9.1 installation CD. It started to boot, but froze up. I rebooted the machine, and the same thing happened. One more reboot, and i get 3 beeps and the power button is blinking. What does this mean?

Hi, it indicates a RAM problem, (or Logic Board around the RAM).
The power on self-test resides in the ROM of the computer. This test runs whenever the computer is turned on after being fully shut down (the power-on self-test does not run if the computer is only restarted).
If a fault is detected during the test, you will not hear a normal startup chime. Instead, the system will beep as explained below. If you experience one of these beeps, you may call your Apple Authorized Service Provider for additional troubleshooting assistance.
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
Note: In this case, a flash is considered to be 1/4 second or 250 ms or greater in length.
http://support.apple.com/kb/ht1547

FaceTime App on my iPad is showing a red number 1, what does this mean and how do I get rid of it.

FaceTime App on my iPad is showing a red number 1, what does this mean and how do I get rid of it.

Same issue here. I tried to follow the suggestion and open the entry in the missed calls list, but when I tap it, a new FaceTime call Is triggered. I do have to delete the entry by swiping left and tap "delete" to get rid of the red circle.

I unplugged the power adaptor and suddenly, my mac started beeping repeatedly like an alarm. What does this mean?

I unplugged the power adaptor and suddenly, my mac started beeping repeatedly like an alarm. My mac was fully charged and would not start up. I pressed down on the restart button to reboot it and the noise stopped.
What does this mean?

Hi, it indicates a RAM problem, (or Logic Board around the RAM).
The power on self-test resides in the ROM of the computer. This test runs whenever the computer is turned on after being fully shut down (the power-on self-test does not run if the computer is only restarted).
If a fault is detected during the test, you will not hear a normal startup chime. Instead, the system will beep as explained below. If you experience one of these beeps, you may call your Apple Authorized Service Provider for additional troubleshooting assistance.
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
Note: In this case, a flash is considered to be 1/4 second or 250 ms or greater in length.
http://support.apple.com/kb/ht1547

Uncaught exceptions...what does this mean?

I have tried searching for information about these messages displaying on my phone but have found nothing regarding them...
My phone has been randomly restarting itself and displaying "uncaught exception 4 >= 4". What does this mean and how do I fix it? Also, not my phone is now recording/updating my call log. When I try to delete the records "uncaught exception 3>= 3" appears. Again, what does this mean and how do I fix it?
I have version 4.6.1.231 (platform 4.2.0.108) for the 8900 Curve. My computer is also a Mac..don't know if that matters.
Can anyone help? I would greatly appreciate it! I've only had this phone since the beginning of August.

Hi and Welcome to the Forums!
Uncaught Exceptions are basically the equivalent of a random error in Windows -- oh wait, you are on a MAC...
In essence, something has happened on the device for which there is nothing in the program code to handle. So the "last out" is what these are. There is nothing really you can directly do to correct (or diagnose, for that matter) them. But there are some things to try:
1) Hard Reboot:
Anytime random strange behavior or sluggishness creeps in, the first thing to do is a battery pop reboot. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
These are good as they reload the device OS fresh, just like rebooting a computer -- a healthy thing that clears up any corruption that has been introduced during operation.
2) Device OS update. If there is some known (not to us, but to RIM) bug, it may have been fixed in a later device OS level. Check your carriers download page via this portal to see if there is an update:
http://na.blackberry.com/eng/support/downloads/download_sites.jsp
Beyond that, there's not much to do except for perhaps figuring out if perhaps it's one of your add-on apps that is causal...and a slow and systematic process is recommended of removing an app, waiting a while (I always recommend a week), then removing another (if the first try failed), and repeating until the errors stop -- at which point you may have found the culprit.
Good luck and let us know!
Message Edited by sdgardne on 10-13-2009 05:21 PM
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

What does this mean:Photoshop 13.1.2 for Creative Cloud Installation failed. Error Code: U44M1P7

What does this mean:Photoshop 13.1.2 for Creative Cloud Installation failed. Error Code: U44M1P7
I found the manual update, which worked!
http://www.adobe.com/support/downloads/thankyou.jsp?ftpID=5595&fileID= 5604

Hi Barbara,
For failed 13.1.2 update error U44M1P7, Please refer to the solution mentioned in the following threads :
http://forums.adobe.com/message/5396792#5396792
http://forums.adobe.com/message/5409050#5409050

Why has my monitor suddenly begun to have a moiré pattern all over – it is even showing up on my icons on the dock? It appears to be very thin bright green vertical lines. I have a 2008 iMac which is running 10.6.8. What does this mean?

Why has my monitor suddenly begun to have a moiré pattern all over – it is even showing up on my icons on the dock? It appears to be very thin bright green vertical lines. I have a 2007 iMac which is running 10.6.8. What does this mean? I've attached some screen shots below.
Also experiencing some funky issues with my wireless keyboard. With new batteries, it will just stop functioning. Certain keys intermittently won't work. Also the fans go on as soon as I turn the computer on - some times they stay on and sometimes they don't. Ever since upgrading the operating system - I've been having many issues with this iMac. Not happy. Any answers out there?

Thanks for your reply LexSchellings, There is no disc in the drive and I went through the suggestions you put forward on the phone with Apple support without any luck. I can put a disc in but it pops straight back out again without registering on finder.
The idea of using an external drive was to enable me to avoid the cost and loss of productivity whilst machine in repair... if I have to take it in to get the old drive removed than I might as well have a new internal drive put in, although I do worry about the reliability of these apple drives given my experience with this one coupled with my limited online research ... on line forums seem to be full of people with the same problem (although perhaps searching such forums is bound to make it seem a common problem as users with perfectly working machines are less likely to post (?)) Your reply suggests that no external drive will work whilst the existing drive is in place.
As a postscript: I do realise that this is a user forum ...my secondary question was asking if anyone knows how to put forward a case/complaint to Apple... I can't find a link on the support page that would enable me to do so and I was wondering if anyone on this user forum had any ideas/experience..

When trying to update my IPad apps I am getting the message "Your Apple ID has been disabled". Still have more than 50$ in my account, so what does this mean ? What can I do to get my ID enabled again ?

when I am trying to download IPad updates I get the message "Your Apple ID has been disabled". What does this mean? How do I get my ID enabled again? Still got more than 50$ in my account !

Reset your Apple ID password here > Apple - My Apple ID
More information here > Apple ID: "This Apple ID has been disabled for security reasons" appears

I'm trying to upgrade to Mountain Lion and I get an error message that says "server error during download; 403 forbidden. What does this mean, what can I do? I had no problem downloading Lion.

Trying to upgrad to Mountail Lion and got an error message : 403 Forbidden. What does this mean? What can I do? I had no problem when I upgraded to Lion.

403 Forbidden HTTP status code in response to a request from a client for a web page or resource to indicate that the server refuses to allow the requested action. In other words, the server can be reached, but the server declined to allow the requested access.
http://en.wikipedia.org/wiki/HTTP_403
Could you be using a different Apple ID oe such?

I am suddenly unable to open my pictures in Adobe Photoshop. It gives the following message: The document "Tina-19.jpg" could not be opened. Photoshop cannot open files in the "Adobe Photoshop JPEG file" format. What does this mean? I have opened my phot

I am suddenly unable to open my pictures in Adobe Photoshop. It gives the following message: The document “Tina-19.jpg” could not be opened. Photoshop cannot open files in the “Adobe Photoshop JPEG file” format.
What does this mean? I have opened my photos in Adobe Photoshop for years and suddenly I get this message and can't open any of my pictures

JoeLib wrote:
You type way faster than me Gene.
Well, not necessarily in this case.
According to the time stamp, Gene posted his answer a bit over three hours before you did, Joe.
Gene's post: Dec 29, 2014 5:54 PM
Joe's post: Dec 29, 2014 8:57 PM

Conference call.. what does this mean

Similar Messages

Maybe you are looking for