Config: Airport Basestation(1st gen w/802.11b) + Airport Express + Xbox
This is the motherload ? for Config./Setup Question:
Airport Baestation(1st gen w/ 802.11b only) + Airport Express + Xbox
(Pertaining to: Network Settings, WDS, Airport Admin Utility)
Network setups (2 possible configurations):
1).Cable Modem ->(WAN)-> Airport BaseStation <-(LAN) -> Lynx Switch -> MacG4(OS 10.3.3) + XBOX using an Airport Express
2).Cable Modem ->(WAN)-> Airport BaseStation <-(LAN) -> Lynx Switch -> MacG4(OS 10.3.3) + XBOX using a Logitech Play Link Wireless Network Bridge
*note with both of these configs. I have only been successful sending my XBox a signal using setup # 2. w/ the Logitech Play Link Wireless Network Bridge.
To this point: (MacG4)
I have installed Amaryllis & Kaid for Mac OS X, & followed the Amaryllis Readme Doc.
I have followed the XLink Quick Start Guide & everthing is a go.
To this point: (Network/Airport Configs.)
I factory reset my AE & ran the AE Assistance. I was able to “Set up a new Airport Express”, & see my AE in the Airport Admin Utility, at that point I got a solid green connection.
Problem:
However, I was only able to do this when prompted “What would you like to do with your Airport Express” if I chose “Connect to my current network”, but at this point if I were to enable(check) the “Extend the range of my Airport wirless network”, & from my understanding this has to be done. I am not able to finish the setup, I get an error right after I enter in my basestation password.
Possible contributing factors to problem:
My password for both my Airport Basestation & Airport Express are the same.
> BaseStation Config. using Airport Admin Utility
1).Internet(tab) >connecting using DHCP.
2).Network(tab) > Distribute IP addresses > I have “Share a single IP address (using DHCP and NAT) enabled, instead of “Share a range of IP addresses (using only DHCP).
3).WDS(tab) > can’t enable WDS and keep settings active. (i.e. I can enable them, but if I close out & return they are disabled.
Airport Express Config. using Airport Admin Utility
1).Airport(tab) > Wireless Mode: “Join an Existing Wireless Network (Wireless Client)
2).Internet(tab) > Connecting using: “Wireless Network”, and Airport(WDS) is grayed out.
The only other thing I am curious if it might be causing some issues with my BaseStation is:
If you navigate to: System Preferences > Sharing > Internet(tab), my internet sharing is turned Off. I noticed a grayed out “Airport Options”, that might become active if I enable Internet Sharing and choose a port to share my connection.
*I didn’t do this becuase I got the warning “If you turn on this port, your Internet Service provider might terminate service to prevent you disrupting it’s network…yada yada..
With all that said, I would be extremely appreciative if someone could drop some serious knowledge on me...
Thx,
MHP :?:
Dual 1Ghz G4 2GigsRAM Mac OS X (10.3.3) Airport Baestation(1st gen w/ 802.11b only) + Airport Express
To extend the range of a wireless network you need WDS and to use WDS you need two Airports:
AirPort Express and all AirPort Extreme base stations can use WDS. Earlier AirPort base stations can't.
http://docs.info.apple.com/article.html?artnum=107454
Similar Messages
-
Airport Express XBox 360 gaming
Can someone give me step by step directions. I am using an airport express for my Xbox 360 and Computer. I can't access locally hosted Xbox games unless I plug the ethernet directly to the XBox. How do I access the local network utilizing the airport express so I can join or host games (Locally)?
DaddyPaycheck,
I found some instructions on the Cisco/Linksys site that talks to having the WRT54G act as a Switch daisy chained off of another Linksys router(which would be connected to the modem). I am hoping those same steps will work with the AE connected to the modem.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/stdadp.php?pfaqid=3733&lid=3726837401B01
Will give it a try after backing up the config I have. Thanks for the reply.
Jay S. -
I have done, what i would call, a lot of research. I have heard that you can and can't configure your xbox 360 to an airport express. Then you can but without any sort of encryption and so forth. Can someone with exceptional experience please squash this question. How and if it is possible configure your airport express to your xbox 360. Let me be more specific! My iMac is connected to the internet through the modem via ethernet. I am trying to connected my airport express to my 360 wirelessly from the iMac. I am running leopard 10.5.1.
I am not sure if this was answered or not, as I cannot confirm which setups you are discussing. Here is what I am trying to do:
1) XBOX 360 via Ethernet to Airport Express
2) Airport Express via wireless to Airport Extreme Base
3) Airport Extreme base via Ethernet to DSL router
Some responses say this works, some say it does not. I think mostly the descriptions of what people are "TRYING" to do are too confusing, so as to make responses unclear. So, the question is, will this work or do I need to get a wireless adapter to connect my XBOX 360 via wireless to the Airport Express (which is what I am trying to do because I don't have $100 for the XBOX wireless adapter.)
Thanks for any and all responses. -
Numerous problems with Airport Express 802.11n with DSL and extending WLAN
Hi all,
I have the following hardware:
802.11b/g Airport Express with firmware 6.3
802.11n Airport Express with firmware 7.3.2
MacBook Pro
iBook G4
Mac Pro PowerMac 2x450 G4
Up until now I had been using the old Airport Express as the base station connecting to my PPPoE DSL line, and it worked fine. I wanted to extend the range of this network, and got another newer Airport Express, the 802.11n model.
First I tried to use the 802.11n to connect to the Internet and the old one to extend the network. Turns out the old one can't be used to extend a network, which is bad enough, but the 802.11n one refuses to connect via DSL for more than a couple minutes, then drops the Internet connection.
So I tried downgrading the firmware to 7.3.0 and 7.3.1, but it didn't help. Did a hard reset, factory default reset, soft reset, nothing worked.
Next I tried swapping the two, putting the old Express back on the DSL line and the new one as the bridge to extend the network (using WPA2). But the 802.11n complains that it can't access the network and flashes amber.
Again, tried upgrading to 7.3.2, downgrading to 7.3.1 and 7.3.0, hard reset, soft reset. Nothing works.
Any ideas?
Cheers,
Fairfax71I don't see any option in the Airport Admin Utility for the old Express for creating a WDS network, only to participate in one...?
That is the option you want to choose.
You could use the newer AirPort Utility to configure the older AX.
Sorry, forgot to ask something else: The 802.11n Express is able to join the WLAN created by the 802.11b/g Express as a client, but not extend it, is that what you're saying?
No. If you join the network the AX is simply acting as another wireless client and is not extending the network. The "extend" option is not available since the older AX is not 802.11n capable. You must use WDS.
Use AirPort Utiity and follow these steps for both AX's. To set up the main AX:
Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
Open AirPort Utility (located in the Utilities folder in the Applications folder on a Mac, or in Start > All Programs > AirPort on a Windows computer). Select the main base station, and choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary. If the base station is using the default password of public, you will not be prompted for a password.
Click the Wireless button, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
Select the “Allow wireless clients” checkbox if you want client computers to connect to this base station.
Click the Add button and enter the MAC address of the base stations you want to connect to this base station. If there is a base station listed that you’d like to remove from the list, select the base station and click the Delete (–) button.
Click Update to send the new settings to the base stations in the WDS. By default, the “Allow wireless clients” checkbox is selected. If you deselect the checkbox, and later want to change the settings on the base station, you must connect to the base station’s LAN port with an Ethernet cable. You will not be able to connect to the base station wirelessly.
To set up the second AX to connect to the main AX:
Open AirPort Utility. Select the AX, and choose Manual Setup from the Base Station menu. Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
Enter the same network password as the main base station, if necessary.
Click the AirPort button, and then click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
Click WDS and choose “WDS remote” from the pop-up menu.
Enter the MAC address of the main base station in the WDS Main field. The MAC address is also referred to as the AirPort ID and is printed on the label on the bottom of the base station.
Click Update to transfer the settings to the base station.
This can be found on page 42 of "Designing AirPort Networks Using AirPort Utility" (direct PDF download). -
Using airport express to extend network of 2tb time capsule.
Is it possible to use my old airport express using 802.11g to extend the network of my 2tb time capsule using 802.11ac protocol? If so, how?
You will need to use one of the 802.11n versions of the AirPort Express....either the model A1264 or A1392....if you want to wirelessly extend the signal from the Time Capsule.
The older 802.11b/g Express does not have the capability to do what you want. -
Hi
Has anyone tried using the AirPort Express Base Station with a first generation Time Capsule and used it to extend their network, while still being able to use the Simultaneous dual-band 802.11n on their network?
Thanks in advanceThe first generation Time Capsule was not a simultaneous dual band device.
If you add the "new" AirPort Express to the network and configure it to "Extend a wireless network", it will extend the one single band signal that it is receiving from the Time Capsule.
In other words, the AirPort Express will not extend simultaneous dual bands in this type of setup...since it can only "extend" what it receives. You would need a simultaneous dual band Time Capsule if you want that type of functionality. -
Adding 802.11b/g AX(s) to multi-Airport Extreme 802.11n roaming network
First, a thanks to folks like Tesserax and Bob for the great ideas on this forum -- the questions & answers I've read have helped me to date, though I still have a question!
My home wireless network today consists of:
One fifth-generation AEBS running in 802.11n only (5 GHz) / 802.11n only (2.4 GHz) mode, on channels 149 (automatic)/11 (automatic) -- provides DHCP services
One second-generation AEBS running in 802.11n only (5 GHz) mode, on channel 157 (automatic) -- bridge mode
There is a wired home network with Cat5e and a gigabit switch in the basement. 30 down/5 up DOCSIS 3.0 service through Time Warner Cable, upstream from the fifth-gen AEBS. The AEBS units are connected in roaming mode via Ethernet.
Using the Airport Utility on my iOS devices, I'm getting "excellent" (59-65 Mb/s) connectivity when I am near either of the AEBS units. It is a large brick house built in the 1920s, and while there are now no dead zones in the house, there are areas where I drop down to 10-15 Mb/s per the Airport Utility. Unfortunately, the two AEBSs are at opposite ends of the house near external walls, one on first floor and one on second -- and the first floor rear AEBS needs to be where it is to serve a breakfast room and sunroom, while the home office AEBS needs to be where I have two Ethernet drops as the cable modem and switch are in the basement.
Before I added the fifth-gen AEBS, I had the older AEBS and two 802.11b/g Airport Express (AX) devices, also in roaming mode. I wasn't thrilled with performance, and while performance is much better with the two AEBS model, I'm wondering about the benefits of redeploying my AX devices elsewhere in the house on the roaming network -- on the theory that I should be getting better 802.11g performance from a device close enough to get max speeds than I am from a farther-away 802.11n AEBS.
However, I am concerned about whether adding back in 802.11b/g devices on 2.4 GHz would restrict the performance of my 802.11n network? I am assuming that might happen because I have 802.11n running on both frequencies... if I stepped back on the fifth-gen AEBS to 802.11n only (5 GHz) / 802.11b/g [or a similar setting] on that device, will that help? Or, am I running the risk of other cross-talk or interference -- or simply of my home network devices being befuddled by multiple access points in a single house?
Alternatively, I could try to replace my 802.11b/g AX units with 802.11n ones -- howeever, having just bought a new AEBS this week, that would encounter cross-talk with my Spousal Budgetary Compliance Unit (SBCU) and I could end up crashing the entire household....
Thoughts and ideas appreciated!If you use the "b/g" AirPort Express devices in a roaming setup, any computers, iPads, etc in close proximity will connect at maximum "g" wireless speeds.
It's really not possible to predict the actual results in advance. The increased wireless coverage might tend to compensate for the lower speeds that would naturally occur due to signal drop off if you did not use the AirPort Express devices at all.
As long as the wireless access points are in a separate room, or separated by 25-30 feet or so from other access points, there should be no confusion that occurs with your laptop trying to connect. It will pick the strongest signal as it moves through the house.
I think the bottom line here is that this is one of those things where you just will not know unless you try. If the Ethernet cabling is already in place, it should not take long for you to find out how things are working. -
Time Capsule (SIM) expand network with 802.11b/g Airport Extreme
Hi, I try to expand a Airport-Network which is set up with a Time Capsule (SIM (latest model). I like to use an Airport-Extreme-Basestation to expand the network. The two devices will be connected wireless. In the helpfile there is a explantation how to do this with 802.11n-devices but when it comes to the 802.11b/g-devices it just says I should have a look on the apple support-pages. I do not find anything there.
I tried everything, but it did not work. I've had a Time Capsule (first model) which died some days ago (the well known powersupply problem). With this Time Capsule I did not had any problems to set up a WDS.
What to do?
Message was edited by: KadegeKadege wrote:
Ok Jolly, thank you, but I started this thread to get in contact to somebody who knows the solution, i.e. has done this before.
Jolly Giant wrote:
try automatic
Of course I've already tried this and the other automatics, but it did not work. That is the reason I am asking for help. So I guess I need special settings.
NOT good !
No protection is not good, ok. But I want it to set up and running and after this I can switch on protection to eleminate some mistake-reasons.
WDS-Mode: "remote WDS-Basestation"
when the UFO joins the TC's network this will no longer apply
But this menu exists and the UFO does not join the network, so I have to select any of this settings!
try these steps provided by Tesserax:
Setting Up Time Capsule as a Second Wireless Router
802.11g AirPort Extreme Base Station -> 802.11n Time Capsule
With "mixed" AirPorts, you will need to configure both routers into a Wireless Distribution System (WDS). Your neighbor's AirPort Extreme Base Station (AEBS) will be the main and your Time Capsule (TC) will be the remote base station in this WDS.
To simplify setup, you should connect your TC directly to the AirPort's LAN port by Ethernet. Once the WDS is configured, you can disconnect the TC and place it at the desired location.
The following are the basic configuration steps to create a WDS:
(Note: To facilitate the WDS set up, jot down the AirPort IDs (MAC addresses) for each of the base stations to be used in the WDS. The AirPort ID and is printed on the label on the bottom/side of the base station.)
Main Base Station Setup - AEBS
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
o Open AirPort Utility (located in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the main base station, and choose Manual Setup from the Base
Station menu, or double-click the base station to open the configuration in a separate window.
o Enter the base station password if necessary. If the base station is using the
default password of public, you will not be prompted for a password.
o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
o Click the Add "+" button and enter the AirPort ID of the base station you want to connect to this base station.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup - TC
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as a remote base station.
o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the remote base station, and choose Manual Setup from the Base Station menu.
o Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
o Enter the same network password as the main base station, if necessary.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS remote” from the pop-up menu.
o Enter the AirPort ID of the main base station in the WDS Main field.
o Click Update to transfer the settings to the base station.
(ref: Pages 42-46 of "Designing AirPort Networks.)
802.11n AirPort Extreme Base Station -> 802.11n Time Capsule
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
does this fix it for you ?
edited by the Jolly Green Giant (where Green stands for environmentally friendly) -
How do you update the firmware on 1st Gen Airport Extreme in OSX Mountain Lion?
A friend gave me a old but never used 1st Gen Airport Extreme 802.11n WiFi Wireless Base Station. I have a couple WiFi dead zones in my house and was told that I could daisy chain the Apple Airport Extreme off of my Verizon FIOS router/modem (802.11G) to fill in the dead spots. During set up the Airport Utility told me that "This version of AirPort Utility requires this AirPort Extreme use firmware version 7.3.1 or later. Go to AirPort Service and Support (link) for more information.
I updated the Airport Utility to the latest version (6.2) and I am still getting the same error message and no other option to update it's firmware. Anyone know of a work around or am I fighting to losing battle here. I tried to contact Apple support, but when I entered the serial number for the Base Station it said the product was over 5 years old and didn't qualify for support service program.was told that I could daisy chain the Apple Airport Extreme off of my Verizon FIOS router/modem (802.11G) to fill in the dead spots
Not sure what you mean by "daisy chain". The AirPort Extreme cannot "repeat" or "extend" the wireless signal from the FIOS router if you are planning to do this using wireless only.
You always need at least 2 Apple routers to be able to "extend a wireless network" using wireless only. The Apple routers would not be compatible with FIOS routers for this type of purpose.
If you can connect the AirPort Extreme to the FIOS router using a permanent wired Ethernet cable connection, then the AirPOrt could be configured to provide more wireless signal coverage that way. If you cannot run the cable, it might be possible to use a pair of Ethernet powerline adapters to send a signal over the existing AC power lines in your home.
When you open AirPort Utility 6.x and a firmware update is available, there is usually a red number next to the AirPort Exreme icon. Click on the red number......or if it does not appear, click on the AirPort Extreme icon and then hold down the option key on a Mac as you click on the Version number that is is displayed to see more "options". -
Airport Express 1st gen A1264 can't be seen in Airport Utility 6.3.2 in OS X 10.10.2
I have acquired a 1st gen 802.11n airport express base station and I am trying to set it up through Airport utility but no matter what I try It won't recognize the device. I am using a 2014 MBP w retina display, 2.8 GHz Intel Core i7, won't be get picked up on my iPad Air 2 either.
Power up the AirPort Express for a few minutes
Hold in the reset button on the Express for 10 seconds, then release
Allow a full minute for the Express to restart to a slow, blinking amber light status
On your MBP, click the WiFi icon at the top of the screen
Look for a listing of New AirPort Base Station
Click on AirPort Express to start the setup wizard
If you are using an iPad, tap Settings on the Home Screen
Tap WiFi
Look for a setting of Setup a New Base Station
Tap on AirPort Express to start the setup wizard
If you have already tried this a few times, and the AirPort Express does not appear, then the AirPort Express is defective. -
First, the reason for my compounded frustration:
I wrote a lengthy, comprehensive post on this late last night. I submitted it and received a notice at this URL:
https://discussions.apple.com/___sbsstatic___/maintenance.html?start=0&tstart=0
It gave a message: "A yellow sticky bearaing the words, "We'll be back soon." and a typed message reading, "We are busy updating Apple Support Communities for you and will be back shortly." Needless to say, it never came back. This morning as I began trying to reconstruct the very detailed post I wrote last night, the Communities system offered me an opportunity to restore the post from last night. Sadly, it contained only a portion of the first line.
I'm going to try it again. The problem inherent in putting it all in words last night, is that I no longer remember the exact wording of the error messages.
I've never gotten this Airport Express (1st gen, purchased mid 2010) to work. I thought it was working, but working poorly. A green light on the device is, apparently, NOT an indication of connection to the wireless. It wasn't workingl.
Description of devices which use the network:
I have a Broadband network with a modem.
It is connecteed to my 2T Timecapsule (purchased mid 2010).
Connected to that is a 24 port Cisco Router.
Not connecting to that, though showing a solid green light, is my Airport Express (1st Generation, purchased mid 2010)
Connected to the router are many ethernet cables giving hard-wired access to:
Printers (HP 8600 Pro purchased 2012))
MacBook Pro (purchased mid 2010) and
IMAC (purchased mid 2010).
3 Apple TV devices (1st generation purchased early 2011)
1 Apple TV device (2nd generataion purchased August 2012)
Connecting to the Wireless Network are IOS devices (current IOS versions on all)
iPad 2nd generation (purchased the day it was available)
iPad 3rd generation (purchased the day it was available)
iPod (mid 2010)
iPhones (4S)
Description of Layout of Network/House
My home is approximately 70 feet by 25 feet.
All Networking hardware is at one end of the house, the south side.
Airport Express (1st Gen, 2010) has been placed in the middle of the house to boost the wireless access at the north end of the house.
Ethernet cables are installed under flooring with cable ends extending up through flooring, and are availble to all devices with Ethernet ports..
Description of Problem
Investigation of the wireless access dysfunction with the iPad (2nd generation, mid 2010) revealed no connection to the Wireless Network, in spite of glowing green light on Airport Express and Airport Utility screen.
Description of actions taken to correct the problem
Loaded Airport Utility on MacBook Pro.
Airport Express shows green light on screen.
Double clicked on Airport Express Icon
Message that Airport Express was unable to extend the network
Message changes suddenly to something about not finding the Airport Express
Airport Utility searches Airport Express, attempting to read its settings
Message appears: Device not found. Airiport Express was previously part of the network, and offers to let me "forget" the base station.
I exit the error message.
A yellow triangle bearing an exclamation point sits to the left of the Airport Express' Description
Airport Express shows green light (as always)
Clicking the link, "Other AirPort Base Stations" indicates no base stations can be found.
Moved Airport Express to the room at the south end of the house containing all network devices
Plugged it in with clear, completely unobstructed view of Time Capsule.
Light on Airport Express flashes yellow and then turns solid green (like always)
Bring Mac into the room at the south end of the house containing all network devices and the Airport Express with the green light
Close Airport Utility on Mac
Reboot Mac
Open Airport Utility on Mac
Airport Express still shows as it did in 1.1.7. above.
Attempts to check Airport Express' access to Wireless network:
Unplugged Airport Express HEY! THE GREEN LIGHT WENT OUT!!! ;0)
Disconnected all Ethernet cables.
Tested ALL devices for Wireless access.
All devices access the Wireless network extremely well (dot and three curved bars) EXCEPT
IOS Devices tested at the north end of the house. These devices show a blank where the wireless bars should be, and intermittently show a dot.
Followed instructions contained in a similar discussion about Airport Express not functioning:
Unplugged all Networking Hardware
Powered off all Equipment which access the Internet in any possible way.
Powered up all Networking Hardware, one at a time, in the order described in that discussion.
Powered up all Equipment which access the internet, one at a time.
Tested ethernet cablingAll equipment functioning.
Tested Wireless access:
Removed all ethernet cabling
All devices, including IOS devices, access the Wireless Network perfectly EXCEPT any placed in the north end of the house. Those perform exactly as they did in step 3.3.2.
Connected all ethernet cabling.
Plugged Airport Express into socket in the Network Hardware room at the south end of the house. I get exactlyt the same results as before. The lovely green light glows on the Airport Express. Airport Utility reports Airport Express cannot find the Wireless network and also says there are no base stations connected to the internet.
Still in Network Hardware room, I attempt to find other base stations by cabling the Airport Express to the MacBook Pro
Airport Utility shows Airport Express with a green light
I double click the Airport Express Icon
Box says connection is average and status is (green light) Extended Network.
I click Edit
I go through each tab. I note that in the Wireless tab, the Network Mode is as I had set it, "Extend a wireless network".
Under the Network tab I note that "Enable Access Control" is as it should be, NOT selected.
Under the AirPlay tab, I note that "Enable airPlay" is selected.
I click cancel and leave the Edit screens.
Curious to know if Airport Express can find the Wireless network now that the device claims to be functioning as an extended wireless network, I disconnect the ethernet cable from the Airport Express.
I watch the Airport Utility screen closely. Nothing is happening.
With bated breath, I double click on the Airport Express icon.
The popup box shows "extended wireless network"
I click on edit and we start the whole mess over again. (See 1.1-9. above)
Curious to know if cabling the Airport Express to the iMac (almost to middle of house) will offer hope and prosperity to IOS devices at north end, I unplug the Airport Express and carry its now-exhausted little body to the iMac, ethernet cable in hand.
As I unplug the iMac from its ethernet access, I'm informed by Cranky Boy that no way is he going to accept that as a reasonable solution to his problem. He will not live wireless while even one ethernet cable is poking up through a floorboard.
Cranky Boy is reassured when informed that, though the Airport Utility shows the Airport Express connected, merely double clicking on the icon produces the same result as laboriously described in 1.1-9. above.
After quieting Cranky Boy by reconnecting the iMac to the Ethernet, I return the Airport Express to the Network Hardware room.
Again, curious to know ... I reconnect the Airport Express to the MacBook Pro. I want to know if it will exrtend the Wireless network from its position one foot from the Wireless Network.
I close and reopen Airport Utility (as I always do, but forgot to write)
I click on the Airport Express icon (which bears a little green light like the other big boys).
BUT THIS TIME, when I click on the Airport Express icon, the pop-up box says my connection is Excellent, the green light status shows, "Extended Network" and clicking on "Extended Network" produces the same old `Airport Express was unable to extend the Wireless Connection.
I click on the Edit option.
I buzz through all the tabs. I cancel instead of update, leaving everything as it was (as I did the first time)
I decide to go back into edit and select "Internet Options" under the "Internet" tab.
Since I have no idea whatsoever as to what IPV6 is and what it governs, I decide to configure IPV6 to Automatically Connect and then, with a whole new set of opportunities, I leave IPV6 Mode set to "Tunnel" and then I learn that I will get to see what happens when "Enable IPV6 Connection Sharing" is enabled.
I check the other tabs to see if anything has changed in their menus
Jesus Saves and so did I.
Apple updates and so did I.
I am warned that my device and its network services will be temporarily unavailable if I continue.
It seems unaware that I am laughing uncontrollably at the suggestion that my device and its services will be TEMPORARILY AVAILABLE. What? An improvement in performance is warned?
Life continues and so do I.
I breathe deeply to decrease my adrenaline.
Airport Utility flashes a red warning next to the Airport Express Icon and then quickly rethinks the matter and decides to show it as connected.
I click on the Airport Express Icon. This time my connection is only "good".
I click on Extended Network. With a new-found consistency it informs me that my device is unable to extend the Wireless network and it chats with me about using the same Wireless password for my device that is used for the Wireless network access. I did. It is.
I change my settings back to the way they once were, I save like Jesus and Update like Apple
I decide to go back into Edit and modify the settings under the Wireless tab, changing from "Extend Wireless Network" to "Join Wireless Network".
I save.
I click on the Airport Express Icon. My connection has degraded further to "Average"
I click on edit just to see what will happen, but no further information is forthcoming. Settings are as I left them.
I wonder if the Airport Express would extend itself now that it has joined the Wireless Network.
I click the Airport Express Icon.
I click Edit
I change the Network Mode from "Join a Wireless Network" to Extend a Wireless Network. Unfortunately, there was no option for "don't forget where the Wireless Network is!"
I am still "unable to extend the Wireless network"
I disconnect the Airport Express from my MacBook Pro.
After closing and opening Airport Utility, I sit and stare at the Airport Express Icon.
It has no light or error messages
It has a yellow triangle with exclamation point
It has no light or error message
It has a yellow triangle with exclamation point
I finally decide to see what THIS error messages says. It says Device Not Found. Patti Harada's AirPort Express was previously part of your network. Check that it is still in range of your network and is plugged into a power outlet. Click Forget to remove this base station from this network."
I click "Forget". Airport Utility has forgotten the Airport Express ever existed. It has also forgotten how to find it again.
I, however, am unable to forget how much I shelled out for this POS and fear I will never recover from working this intensely and tediously on documenting something so hideously inconsistent in its test results.
I wonder if I should recable the Airport Express to my MacBook Pro
I decide I've had about enough.
I document this ad nauseum in the hopes that someone can read it THOROUGHLY and offer me a solution to my problem. What is my problem? I am so busy fighting off Alligators that I forgot I only came in to drain the swamp! Ah, but I remember now: Cranky Boy can't watch Netflix on his iPad (2nd generation) in the north end of the house.
Any solution that works will do. I'll buy another piece of whatever kind of equipment you think best.Well, aren't you all that and a bag of chips!!!!
Oh what a relief! What a RELIEF!
That just cleaned up my life. And Cranky Boy is actually smiling!!!
Houston, we've got dots AND BARS!!!
P.S. All my firware and software are always current. If I spent as much time looking for a reset button as I spend checking for software updates, I mighta not needed to work at this!!!!
P.P.S. Airport Utility shows Cranky Boy's iPad as the Airport Express' Wireless Client!!! Who knew?
Thank you so much, m'Lord. I am in your debt. What would you have me do?
Patti in Tucson AZ -
I have an old 1st gen express. Airport utilities 6.3 won't set it up. How do I set it up in Mountain lion?
I have an old 1st gen express
Please check on the side of the Express and locate the Model No.
A 1st Gen AirPort Express is Model No A1264.
AirPort Utility 6.3 will definitely set up a 1st Gen AirPort Express.
Is this what you have? -
Airport Utility v.6.2 not compatible with 1st gen Extreme?
Hello All,
Ruh Roh!!! Recently upgraded my Macbook Pro from 10.6.8 to 10.8.2. Attempted to reconfigure 1st gen Airport Extreme and received the 'not compatible' notice. I'm connecting through it ok at the moment; workaround? Can I go back to a previous Utility version?Attempted to reconfigure 1st gen Airport Extreme and received the 'not compatible' notice
A 1st Generation AirPort Extreme is compatible with 10.8.2.
Is this the model that you have?
Or, is your AirPort Extreme the older "round" version? Apple dd not use Generation numbers on the "round" version of the AirPort Extreme. -
Apple TV 3rd Gen no longer sees Airport Express 1st gen in Airplay after update
Apple TV 3rd gen was connected to AirPort Express 1st gen via WiFi, drove a video device via HDMI
and sent audio to the AirPort using Airplay and selecting the AirPort Express under Speakers.
I could adjust the volume with the AppleTV remote.
Apple TV was stored unused for a while.
After powering on yesterday, I ran the update.
Now Apple TV is connected to the Airport Express via WiFi
but Airport Express doesn't show in AirPlay settings.
I can still use AirPlay from my MacBook running Snow Leopard.
There are no updates available for the AirPortTry the following steps, check whether things are working after each step where appropriate, before trying the next.
Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
Restart the Apple TV (Settings > General > Restart).
Restart the Apple TV by removing ALL the cables for 30 seconds.
Restart your router. (Also try removing it’s power cord for at least 30 seconds)
Restart your mobile device.
If you are still having problems, the following article(s) may help you.
Troubleshooting AirPlay
Troubleshooting Wi-Fi networks and connections
Recommended Wi-Fi settings
Wifi Diagnostic Software (for Mac users)
You may also find some help on this page, where I’ve collected some of the more unusual solutions to network issues.
When making adjustments to your network for better optimisation, you may find some of the points mentioned on this page helpful. -
I have a Netgear wireless ADSL modem router (wireless + four ethernet out ports) that i'd like to connect to a 1st gen Airport Express to create a small home network to provide internet access for a MacBook, iPhone and Apple TV, and to provide Airplay connection to the Apple TV and Airport Express audio output jack.
I'd like to turn off the wireless function of the ADSL modem router, and to have from one of its ethernet out ports an ethernet cable providing internet directly connected to my MacBooks ethernet port.
Then from one of the other ethernet outs on the ADSL modem router an ethernet cable connected to the Airport Express's ethernet port. This would be to provide wireless internet connection for the Apple TV and iPhone via WiFi from the AE.
At the same time as the MacBook is receviing internet soley via the ethernet in port, i'd like it to have WiFi connection to the AE to provide Airplay connection to the Apple TV and the AE's audio out jack.
Is this all possible? How should I go about to configure this? How should the AE's ethernet port be configured?
Any special modes the ADSL modem router or Airport Express should be in? ie bridge or client?
ThanksOn the ADSL modem router web-based interface, should I set any security setting? I think not as there'll be no wireless signal coming from it, only wired ethernet connections to both MacBook and AE. Security should only be set on the AE to prevent someone from accessing its WiFi signal. Is this assumption correct?
These are all correct!
How should I go about setting up security for this network?
First I would recommend that you configure the AirPort Express for WPA2 Personal. This will provide you with the greastest level of security while still providing excellent bandwidth performance.
You would configure wireless security for the Express by using the AirPort Utility on a Mac, PC, or iOS device. Using your MacBook Pro as an example, you would do so as follows:
Run the AirPort Utility.
Select the Express, and then, click on Edit.
Select the Wireless tab to enable it.
Set the Wireless Security option to: WPA2 Personal
Enter the desired password in both the Wireless Password & Verify Password fields. Note: Use of a "strong" password is encourage here. By strong, I mean use a mix of upper/lowercase letters, numbers, & punctuation marks. Try not to use common dictionary words. If you operate your wireless in an area where security is of an utmost concern, I would further suggest that you change the wireless security password every 60-90 days. Also don't forget to change the default AirPort Base Station Administrator password as well.
Click on Update and allow the Express to restart.
Maybe you are looking for
-
Design of Cube to Store SEM Target Data - for HR
Hello, I am in the process of completing a Scorecard and Management Cockpit for the HR function at my company. Currently, the most perplexing piece is how to handle targets. I know they can be entered via BPS, have to be stored in a BW InfoProvider
-
Reset Cleared Items - for huge number of line items (DUPLICATE)
Hi Moderators, Can this be deleted please? Thanks, Joey Edited by: Jose Enrico Mangaser on Nov 3, 2009 8:23 AM
-
Using the Import utility from other users and going to a different schema
I has a user today with rights Insert into XXXX.TABLE values(); Works just fine for another schema's table which has select,insert,update,delete. We tried to utiile the import utility from OTHER USERS Insert failed ORA-00942 Do you want ot ignore all
-
HT4356 How do I disable the ability to print from an iPad?
How do I disable the ability to print from an iPad?
-
Hi there, i am searching for a DTW template for uploading activities. It is possible to upload activities via DTW. I do not find any template. Regards Steffen