Config archiving problem

Hi
am having problem in archiving config from switches in cisco works. am having problem in only 5 switches all others switch configurations archived when I try to do this I found following error.
TELNET: Failed to establish TELNET connection to 172.25.2.102 - Cause: Authentication failed on device 3 times. PRIMARY-RUNNING config Fetch Operation failed for TFTP. Failed to detect SSH version running on the device. Failed to fetch config using RCP.Connection refused: connect Verify RCP is enabled or not.
can any one help me to fix this
Thanks

Hi
Thanks for that apparently nearly 200 switches are working only 5 switches we have a problem. please see snmp config below. I have added RW recently it is not taking effect. please see screen shot of working one and not working
snmp-server community comms RO
snmp-server community comms RW
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps cpu threshold
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps flash insertion removal
snmp-server enable traps port-security
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps license
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps hsrp
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps vlan-membership
snmp-server host 172.16.25.12 comms
snmp-server host 172.16.25.13 comms

Similar Messages

  • RME config archive problem - lms 3.2

    just wondering if anyone else has seen this.
    about a month or so ago, I grabbed about 6 or 7 patches for our ciscoworks machine, across cm, rme, and cs. (yeah, we were a little behind)
    after applying these patches, it seems, all of the 2960s and 4948s are failing the config archive with the following:
    cm00139: could not archive config:cause: action: verify that device is managed and credentials are correct. Increase timeout
    value if required.
    so I've triple checked the credential set applied to these devices, adjusted timeout and retry values, and have gotten nowhere.
    Deleting these devices doesn't seem to help, they are rediscovered just fine, but the config archive continues to fail.
    Other than maybe trying to reinstall the rme patches (or uninstall) that were recently applied, I'm out of ideas. This is LMS 3.2.1 with
    cm 5.2.2
    cs 3.3.1
    rme 4.3.2
    running on windows server 08.
    So if anyone may have seen this and/or has any advice, I'd appreciate it. Thanks - chris

    ok, so it's been a year and a half since last post. So in addition to the above mentioned archive failures with the 4948s, the 4948s were also showing up in config out of sync summary. The only difference that were showing between running and startup was the ntp clock period.
    I did see that the clock period statement was in the exclude list for routers and a bunch of other things, but not for the 4948s. I added this as an exclusion yesterday. Today when I checked, all 4948s are archiving now, and are off the out of sync report. Never would have crossed my mind to check there, but that exclusion seems to have done the trick. Maybe someone else can use this if they're seeing the same thing. - chris

  • Cisco Prime 2.2 Config Archive get Partial-Success

    Good morning everyone!
    I have a question regarding Cisco Prime Infrastructure 2.2 and Config Archive. Im trying to backup a configuration for an old WS-CBS3020-HPQ blade with IOS version 12.2(58)SE1 and im getting an error under "Fetch vlan" that says :
    Couldn't able to collect VLAN on the device. TFTP server not accessible from device.
    Im not sure what this means? It gets partial-success, but the error message worries me. Im not able to find anything in the logs or by searching for the error code. Anyone have any idea where to look? The credential is correct, i tripple checked :)

    I tried using the "tftp-server flash:" command, but didnt help. Im also seeing this problem with a couple of Cisco 3750x switches.

  • Error Message in config Archive in RME in LMS 4.2

                      I got the below error message in the config archive in the LMS 4.2.
    CM0056 Config fetch failed for 10.0.0.10  Cause: CM0204 Could not create DeviceContext for 797 Cause: CM0202 Could not access 10.0.0.10 via SNMP. Action: Check the Read Community string Action: Check if required device packages are available. Action: Check if protocol is supported by device and required device package is installed.
    Switch model type is 3560 and 2960
    Please tell me the reason for this issue.

    Are you usig only TFTP option to archive configuration. Try to use the telnet/ssh. TFTP as a protocol set for config archive.
    Check the Credential verificatio job to see if the crendentials are configured correctly.
    -Thanks

  • HT1430 Iphone 5 OS 6.1.1, When I turn off or restart device, this device automatic unmute. How can i config this problem?

    Iphone 5 OS 6.1.1, When I turn off or restart device, this device automatic unmute. How can i config this problem?

    Hey everyone in Apple world!
    I figured out how to fix the flashing yellow screen problem that I've been having on my MBP!  Yessssss!!!
    I found this super handy website with the golden answer: http://support.apple.com/kb/HT1379
    I followed the instructions on this page and here's what I did:
    Resetting NVRAM / PRAM
    Shut down your Mac.
    Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.
    I went through the 6 steps above twice, just to make sure I got rid of whatever stuff was holding up my bootup process.  Since I did that, my MBP boots up just like normal.  No flashing yellow screen anymore!!   
    (Note that I arrived at this solution when I first saw this page: http://support.apple.com/kb/TS2570?viewlocale=en_US)
    Let me know if this works for you!
    Elaine

  • Config Archive Failure

    This image shows that I have Telnet, SSH, TFTP and HTTPS configured for  Config Fetch. What am I missing?
    Thanks Joseph!
    I don't know why, but nearly ALL of my Config Archive VLAN is failing. I am  receiving the following:
    TELNET: Failed to establish TELNET connection to xxx.xxx.xxx.xxx - Cause:   Connection refused. Command failed  VLAN Config fetch is not supported using  RCP.   VLAN Config fetch is not supported using TFTP.
    The above switch is using SSH - not Telnet, but it doesn't try???
    The other error is:
    Command failed  Could not detect SSH protocols running on the device     VLAN  Config fetch is not supported using RCP.   VLAN Config fetch is not supported  using TFTP.
    On this one, it should be using Telnet as that is what is supported on this  particular switch.
    I have verified the credentials are set up correctly for both of these.
    Also, this isn't isolated - it's happening on 293 devices. Only 2 are  successful.
    Any help would be GREATLY appreciated! I am running LMS 3.2

    The following is what I see in the logs:
    ],ERROR,[Thread-1926],com.cisco.nm.rmeng.dcma.configmanager.ConfigManager,updateArchiveForDevice,1355,VLAN RUNNING Config fetch Failed for csw-a1xc-201-004
    [ Fri Oct 08  06:27:18 MDT 2010 ],DEBUG,[Thread-1926],com.cisco.nm.rmeng.dcma.configmanager.ConfigManager,updateArchiveForDevice,1361,Message : Command failedSSH: Failed to establish SSH connection to x.x.x.x -
    Cause: Authentication failed on device 3 times.
    VLAN Config fetch is not supported using TFTP.
    Please ensure that you have the credentials corrected in the DCR under Common Services --> Device and Credentials --> Devices Management --> Select all the devices in question, edit credentials.
    1. Ensure the primary enable username and password is correct and populated.
    2. Ensure you are using the correct SNMP RO/RW community string and must be populated.
    3. Ensure that all firewall rules allow traffic to and from LMS and devices. Check port 69 UDP and high ports number are allowed.
    4. If this is a multi-home system with two nic cards, go to RME ---> Administration --> System Preferences --> RME Device Attribute --> Add Natted RME IP Address
    Afterwards, rerun the device credential verification to test for telnet, ssh, SNMP RO and RW and ensure it passes. Then do a sync archive and let me know the results.

  • Partially Collected Config Archive

    Hello,
    For 3 switches config archive is partially collected,After searching from enough threads i have done the below but still no sucess
    i have given enough rights to tftpboot dir for caususer
    created a vlan.dat in tftpboot folder
    manually copied vlan.dat from switch to the file in vlan.dat
    start a job of syn but no sucess.
    Any hints experts.
    Thanks

    Dear's
    Waiting for ur replies??
    Thanks.

  • Call manager and rme config archive report

    Hi,
    I know that rme does not support the call manager for config archive. It is clear.
    The RME home page show config archive status for failed devices and there are some devices which are not supported by RME config archive.
    I've set this devices to suspended state in RME but config archiv is trying with this devices also.
    This is a financial costumer and the local Financial supervisory authority would like to see all devices config is saving successfully.
    How can i exclude the call manager and similar devices from config archiv process and status reports?
    Regards,

    Hi,
    I would like to qoute from RME help.
    Working With Suspended Devices
    Suspended device state cannot participate in any RME application flows but all historical data pertaining to the device will continue to be maintained by RME.
    Nevertheless the RME is trying to fetch the config from suspended devices!!!
    What is the truth in this thing?
    Regards,

  • Prime Infrastructure 2.1 - Config Archive

    In PI2.1, is it possible to send the config archive of my devices to a network drive?  TIA

    PI will always save the configurations into its database. That database is always on the PI server itself.
    You can export the configurations from the database via a manual process - you could probably script it and kick it off via cron if you are handy with that sort of thing.
    The export process is explained in a post by Vinod Arya in the Prime Infrastructure Ask the Expert thread.
    (Edit - corrected link)

  • Config Archive for Call Manager

    Hello,
    It give me the attahced error fo r config archive for call manager.

    The supported devices page shows each supported device, and what features are supported:
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html

  • Config archive failed for devices no longer on DCR

    RME reported 30 devices failed config archive but this devices are already removed from DCR but RME keep reporting this devices. how I can clean up thiese devices from RME?
    Thanks

    You can contact TAC, and they can give you the procedure to surgically remove these device records from the RME database.

  • PI 2.0 configuration archive problems

    Hi,
    I've got 2 problems with archiving device configurations in Prime Infrastructure 2.0.
    1. Configuration archive job status is Completed and Last run status is Success
    Looking at Configuration archive results, I see this:
    Fetch Running: Success
    Fetch Startup: Success
    Fetch VLAN: Unsupported operation
    Fetch Modules: N/A
    Archive: Success
    It's a Cisco 7200 router.
    Looking at its Configuration archive, I can see just the running config. Startup config is missing.
    2. Configuration archive job status is Completed and Last run status is Partial-Success
    Looking at Configuration archive results, I see this:
    Fetch Running: Success
    Fetch Startup: Success
    Fetch VLAN: Unsupported operation
    Fetch Modules: N/A
    Archive: Error in archiving for device '3663756'
    It's a Cisco 6500 FWSM.
    Looking at its Configuration archive, I can't see anything, it says 'No data available'. Both running and startup configs are missing.
    Do you have some ideas what is wrong here, why can't I see the configurations?

    I've found the reason why this is happening. In the case when startup and running configs are identical (disregarding lines like 'last configuration change', 'ntp clock-period',...), Prime doesn't show startup config under Configuration Archive, it
    just shows the running config.

  • [Solved] Thunderbird archiving problem

    I have an account on fastmail.fm, and I would like to use Thunderbird to access it. I tried it, however, there seems to be a problem while archiving mail. Whenever I click the archive button, instead of transferring mail to the "Archive" folder of my account, it creates a folder named "Archives", creates a subfolder within of the year (2015 for this year, for example), and shoves the mail there. I changed this folder in the account settings page such that Thunderbird would (logically) archive to the existing "Archive" folder. However, Thunderbird does not seem to be respecting this. Does anyone know of a good reason for this and how I may fix it?
    Last edited by genghizkhan91 (2015-01-15 06:02:05)

    Yup, I am. As of now, I've changed some settings in the about:config dialog of Thunderbird, and it seems to be respecting the issue. I'm not marking it as solved yet, for I want to see if this persists. If it keeps working out as it seems to be right now, then I shall mark it fixed.
    It seems to be an issue because I have multiple aliases attached to my fastmail account. It seems that setting the option in the accounts pane doesn't set it for all your aliases. You need to set them all manually using the config editor. Or at least, that's what I've concluded as of now.

  • Is it archive problem?

    Hi
    We have created Miro invoice in the year 2005, and it got cleared in the same year.
    Now in database, we have accounting documents which are only from 2006
    2005 Documents are not available in BSEG table since those are archive
    And the problem is, if i take that tax gl account which is used in invoice in 2005 in FBL3N, still it is in open item
    And same item is displaying in BSIS also, and if i verify the concerned cleared document in BSAS it is not available, i think since it has been archived.
    My doubt is if the fi document is archived, why only tax line items are still open in FBL3n and main document is archived the related tax line item should be also archive or not?
    Thanks for suggestions
    Vishnu

    Refer the below thread.
    [http://forums.sdn.sap.com/message.jspa?messageID=11014661#11014661]

  • Sender Adapter archiving problem

    Hello All,
                 In the sender adapter channel, we are getting the following error message. The messages are not getting archived in the archive folder that we have mentioned in the Sender adapter configuration in the ID.
    Putting message into send queue failed, due to: com.sap.engine.interfaces.messaging.api.exception.DuplicateMessageException: Message Id 36f5f1e6-97a8-41b0-1fb8-b9c2bdbb6008(OUTBOUND) already exists in duplicate check table: com.sap.sql.DuplicateKeyException: ORA-00001: unique constraint (SAPPIXDB.SYS_C00159667) violated .
    Returning to application. Exception: com.sap.engine.interfaces.messaging.api.exception.DuplicateMessageException: Message Id 36f5f1e6-97a8-41b0-1fb8-b9c2bdbb6008(OUTBOUND) already exists in duplicate check table: com.sap.sql.DuplicateKeyException: ORA-00001: unique constraint (SAPPIXDB.SYS_C00159667) violated
    Could you please let me know the exact problem? And how to resolve this? Thanks.

    Hi there,
    This error is issued if a user tries to insert an already existing value into a column defined unique.
    This error will also be generated if an existing record is updated to generate a duplicate (unique) key. Typically this is a duplicate primary key, but it need not be the primary key.
    Remedy:
    Only one of the following will be appropriate:
    1. Remove the unique restriction.
    2. Change the restriction to allow duplicate keys. An index could be changed to be a non-unique index, but remember that the primary key must always be unique.
    3. Do not insert the duplicate key.
    Cheers'
    Neetesh

Maybe you are looking for