Configurable BOM download

Dear Experts,
Can we download configurable BOMs from ECC to CRM? If not, is there any other way out to do this?
Thanks,
Kanthimathi

Did you try the initial load of object BOM in trx R3AS?
Regards.

Similar Messages

In dreamweaver mx 2004 and dreamweaver cs4, how I configure, when download/upload do not ask me to include DEPENDED FILES but act without including ?

in dreamweaver mx 2004 and dreamweaver cs4, how I configure, when download/upload do not ask me to include DEPENDED FILES but act without including ?

Open the Preferences panel (Edit menu on Windows, Dreamweaver menu on a Mac), and select the Site category. There are two checkboxes there for dependent files. Make sure both are selected. The Dreamweaver default is NOT to upload/download dependent files. You need to click Yes, if you want the dependent files to be included.

Virtex6:Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings

Hello，everyone.
I am using virtex6 FPGA and trying to download mcs file to PROM and have failed.
I download .bit file to FPGA and succeed.
When i try to download .mcs file to PROM XCF128X-FTG64C(BPI Flash) and choose Slave SelectMAP Mode
and the process is about 68% it fails.
The message below the IMapct is as belows:
done.
PROGRESS_END - End Operation.
Elapsed time =      0 sec.
// *** BATCH CMD : identifyMPM
// *** BATCH CMD : assignFile -p 1 -file "C:/Users/Administrator/Desktop/TEST/LED/led.bit"
'1': Loading file 'C:/Users/Administrator/Desktop/TEST/LED/led.bit' ...
done.
INFO:iMPACT:2257 - Startup Clock has been changed to 'JtagClk' in the bitstream stored in memory,
but the original bitstream file remains unchanged.
UserID read from the bitstream file = 0xFFFFFFFF.
INFO:iMPACT:501 - '1': Added Device xc6vlx240t successfully.
INFO:iMPACT - Current time: 2014/3/13 8:48:14
// *** BATCH CMD : Program -p 1
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': Programming device...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:579 - '1': Completed downloading bit file to device.
INFO:iMPACT:188 - '1': Programming completed successfully.
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
INFO:iMPACT - '1': Checking done pin....done.
'1': Programmed successfully.
PROGRESS_END - End Operation.
Elapsed time =     23 sec.
Selected part: XCF128X
// *** BATCH CMD : attachflash -position 1 -bpi "XCF128X"
// *** BATCH CMD : assignfiletoattachedflash -position 1 -file "C:/Users/Administrator/Desktop/TEST/LED/leda.mcs"
INFO:iMPACT - Current time: 2014/3/13 8:49:32
// *** BATCH CMD : Program -p 1 -dataWidth 16 -rs1 NONE -rs0 NONE -bpionly -e -v -loadfpga
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': BPI access core not detected. BPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file D:/Xilinx/14.3/ISE_DS/ISE/virtex6/data/xc6vlx240t_jbpi.cor.
'1': Downloading core...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:2492 - '1': Completed downloading core to device.
Current cable speed is set to 6.000 Mhz.
Cable speed is default to 3Mhz or lower for BPI operations.
Current cable speed is set to 3.000 Mhz.
Setting Flash Control Pins ...
Setting Configuration Register ...
Populating BPI common flash interface ...
Common Flash Interface Information Query completed successfully.
INFO:iMPACT - Common Flash Interface Information from Device:
INFO:iMPACT - Verification string: 51 52 59
INFO:iMPACT - Manufacturer ID:        49
INFO:iMPACT - Vendor ID:             01
INFO:iMPACT - Device Code:           18
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x008CE03B.
done.
'1': Erasure completed successfully.
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
Setting Flash Control Pins ...
'1': Flash Programming completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Reading device contents...
done.
'1': Verification completed.
Setting Flash Control Pins ...
Current cable speed is resumed to 6.000 Mhz.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
`Elapsed time =    814 sec.
and i find many people have met the same thing. But they are spartan series FPGA and i try to low the Resistances of Mode pins,M0 M1 and M2, but the problem does not been solved.
I have read the status Registers and find there is an over-temperature state
and in Impact i could not readback the registers. It is strange.
I am anxious about this problem and have not solved it yet
What reasons may it be?
Hope for your answer, thank you

Hi~I want to know if you solve the configuration problem for virtex-6?
As I encounter the  same configuration problem, I want to consult  you with some question.
Can I have your email?
gszakacs wrote:
I have measured the VCCINT and find it is 1.0V, not 2.997V;
That is not at all surprising. I always assumed the problem is with reading the XADC (system monitor) block and not with the voltage or temperature.
my Reference board is ML605
That would have been nice to know at the beginning...
It seems that you have selected the correct mode, assuming your jumpers are set as required in the ML605 Hardware User's Guide. See table 1-27, table 1-33 and the note below it about switch S1.
I'm not that familiar with the details of this reference design, but it may be that the slave SelectMap circuitry requires a reset or power cycle to actually configure the FPGA. Have you tried power-cycling to see if the FPGA boots from the flash?
I'd also suggest that you select the V6 in the JTAG chain view, then go to the debug menu of Impact and select Read Device Status (this is from memory, but it's something like that). That will not only show the bits of the configuration status register, but also describe what each bit means. Among other things you can check the state of the FPGA's configuration logic and the Mode pins.

How to configuring the download manager

RE: Firefox v22.0 | Linux Mint 15 Cinnamon v1.8 (32bit)
How can I configure the download manager to intercept "EVERYTHING" regarding the updates to the addons and plugins? I want to intercept everything and determine myself where I want the stuff to be saved. As for the addons/plugins (generally ".xpi"), I want to save them to a specific location and then I can install them into Firefox after the download(s) is/are complete. I already have the option "Always ask me where to save files" selected but any addons/plugins that are added or updated are not affected by this selected option. Instead, they are updated/added ... more or less ... with my saving them to a specific location other than in Firefox.

Firefox will not detect .xpi (addons/extentions) using the Firefox download manager to save the .xpi's. Instead Firefox is downloading the .xpi and then asking to install them or not. I already have the option "always ask where to save files" checked. As for downloading manually, nope! If using FIrefox browser, you cannot download manually and expect to save them to a different location. It appears that, at present, I will either accept the current download manager (Firefox) as is or will have to use a 3rd party download manager; either application or addon. I am looking at the Firefox addon "Download Them All (dTa)" to use for a download manager and thus bypassing the Firefox default download manager. Anyway, thanks for the responses.

How to Make a BOM as Configurable BOM ?

Hi,
Please answer my question , How to Make a BOM as
Configurable BOM ?
Regards,
Abhilash

Dear Abhilash,
Please refer to the following link:
http://sap-img.com/sap-sd/sales-bom-implementation.htm
I will suggest you to visit http://sap-img.com/sap-sd.htm. It will give you the overview of SAP SD module.
Moreover there is a separate section of FAQs with answers which will help you in great deal.
Do let me know in case of any queries.
Hope this helps you.
Do award points if you found them useful.
Regards,
Rakesh

Configurable BOM costing

Hi,
I am trying to cost a Multilevel configurable BOM in CU50. The header material has 'quantity structure' checked in material master and it has some planned cost in material master.
When i am costing it, it is determining the costing variant as standard PPC4 and transfer control as PC03 but it is giving an error:
" No itemization exists for material XXX plant YYY"
What could be the issue?

Resolved....wrong Quantity Structure option in costing Variant.

Configuration data download to FPGA was not successful.

I have designed a board with the Spartan 6 LX9 TQFP144 Package.
I am able to load a bitstream to the device with the digilent HS-2. However the fpga can not selfconfigure from
the attached SPI Flash.
Here is the console output from iMPACT:
GUI --- Auto connect to cable...
INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
INFO:iMPACT - Digilent Plugin: found 1 device(s).
INFO:iMPACT - Digilent Plugin: opening device: "JtagHs2", SN:210249983579
INFO:iMPACT - Digilent Plugin: User Name: JtagHs2
INFO:iMPACT - Digilent Plugin: Product Name: Digilent JTAG-HS2
INFO:iMPACT - Digilent Plugin: Serial Number: 210249983579
INFO:iMPACT - Digilent Plugin: Product ID: 30900152
INFO:iMPACT - Digilent Plugin: Firmware Version: 0109
INFO:iMPACT - Digilent Plugin: JTAG Port Number: 0
INFO:iMPACT - Digilent Plugin: JTAG Clock Frequency: 10000000 Hz
Attempting to identify devices in the boundary-scan chain configuration...
INFO:iMPACT - Current time: 27.07.2015 16:19:26
PROGRESS_START - Starting Operation.
Identifying chain contents...'0': : Manufacturer's ID = Xilinx xc6slx9, Version : 2
INFO:iMPACT:1777 -
Reading C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9.bsd...
INFO:iMPACT:501 - '1': Added Device xc6slx9 successfully.
done.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Selected part: N25Q128
Unprotect sectors: FALSE
INFO:iMPACT - Current time: 27.07.2015 16:20:19
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': SPI access core not detected. SPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9_spi.cor.
'1': Downloading core...
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
'1': Reading status register contents...
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1100 1110 1100
INFO:iMPACT:2492 - '1': Completed downloading core to device.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': Erasing Device.
'1': Using Sector Erase.
'1': Programming Flash.
'1': Reading device contents...
done.
'1': Verification completed.
'1':Programming in x4 mode.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
INFO:iMPACT - '1': Flash was not programmed successfully.
PROGRESS_END - End Operation.
Elapsed time = 78 sec.
If i read that correctly Data was written to the Flash but the fpga was not able to configure from that data.
Done-pin is connected to 3.3V via a 470 Ohms Resisor.
The Flash is a N25Q128A13ESE40G, Datasheet here: http://www.farnell.com/datasheets/1674445.pdf
I can perform a readback, checksum and an erase.
If i do a read device status this is the console output:
INFO:iMPACT - Current time: 27.07.2015 16:36:27
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
INFO:iMPACT - '1': Reloading FPGA configuration data stored in flash...
INFO:iMPACT:182 - done.
On the Flash side I have pulled s# and Hold up to 3.3V with 100k Resistors.
Can someone help me to find the problem?

So does the FPGA try to read the SPI flash when it boots ?
out with scope, probe the clock and the data , see if you can see it streamig out when you boot.
If so, then one other thing I see wrong a few times is data path of the SPI, single bit or 4 bits of data.
you have to make certain the bit file was created in the same width as the fgpa is expecting,
In ISE I think its in Impact where you make the SPI flash file and specify this .

V5 in BPI Mode " Configuration data download to FPGA was not successful. DONE did not go high,"

Hello，everyone.
I am using virtex5 XC5VLX155 FPGA and trying to download mcs file to BPI flash and have failed.
The flash is JS28F512P30E. The iMpact version is 14.7.
FPGA's VCCINT is 1.0V, VCCAUX is 2.5V. VCCO is 3.3V.
M[2:0] is 010 in Master BPI. Ican program FPGA through JTAG. The FPGA_DONE pin 's LED can always flash.
The error is shown as below. the full IMPACT console log and the SCHEMATIC_ FLASH are in the attachment.
Using x16 mode ...
Setting Flash Control Pins ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x004E4AFF.
done.
'1': Erasure completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
'1': Flash Programming completed successfully.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
PROGRESS_END - End Operation.
Elapsed time = 692 sec.
Hope everyone give more advices. Thank you.

Thank you very much!
I can read ack the mcs file, but the file is much bigger than the original mcs file.
The flash datasheet is in the attachment.
I want to use the Master BPI mode. In BPI_UP, the address starts at 0 and increments by 1 until the DONE pin is
asserted. I do not know the difference between the BPI_UP and BPI_DOWN.
ps: The R61,R62 and R63 are not weld on the board. The ADV pin is tie to VSS .

BOM Download with prodution order to SAP ME

Hello Experts,
I am having an issue with transfer of BOM with production order to SAP ME and would appreciate your inputs.
The issue is as follows:
I have a product assembled on two different routing. BOM is same and is assigned to respective routing in SAP ECC material master production versions.
I am not sending the BOM to SAP ME and in system rule maintenance, setting for "Ignore BOM update" is set to FALSE.
When I send a production order with routing 1, a corresponding BOM is created in SAP ME and operation assignment is also mapped in the ME BOM.
But when I send a production order for same material on 2nd routing, BOM with assignment of operations from 2nd routing is not created. Instead it refers to the 1st BOM only with assignment of operations from 1st routing.
In both cases correct routing are getting copied though.
I have checked the Request and Response trace report for production orders. In request, components with correct operation assignments are coming. for both the production orders. In the response for 1st production order, BOM reference is coming correctly (either it refers to an existing BOM with same operation assignment or creates a new one).
But the response for the second production order picks up the existing BOM with operation assignment of 1st routing and not creating a new BOM.
As per the help documentation, it is supposed to create a new BOM when there is a difference in operation numbers in BOM downloaded with production order.
Can some guide me on this please?
Thanks in advance,
K S Srinivas

Hello Sergiy,
Thanks for the inputs. I did have a look at the SAP Note mentioned by you. It does describe exactly the same problem that I have encountered. My Basis colleague is looking in to it.
I will revert back once I am done with this.
But in the absence of this, I was able to get a simple work around by creating two alternatives of BOM (same BOM components) and assigning to two production versions of same header material. In this case order download creates two BOMs.
Thanks for the iput.
Srinivas
PS: I have posted another issue. Would be nice of you if you could give your valuable inputs on this too.
Srinivas

What is quick upload configuration for downloads?

What is quick upload configuration for downloads? I cannot get downloads to open because of the box popping up wanting some kind of configuration.

I have the same question as nyswaner and have been using macs for the past 20 years. The problem just popped up recently. I can download but am unable to open the file. It asks for right clicking and selecting a favorite folder. Under Details (on the following screen) it asks for a Host, then wants a username and password. I'm having this problem on a home computer that is not connected to a virtual private network. I've been running Fusion5 (virtual machine) to comply with my organization's WindowsXP operating sytem, for a single application but deleted it as I can get the info now on my iPad and iPhone. Is there anybody out there who has the same problem and was able to solve it? The software I downloaded is for specific use with the Mac operating system and having to use a proprietary Windows browser to open Mac software can't possibly be true. BTW nyswaner, Parallels and Fusion are software applications that enable you to run Windows on your Mac computer in a "virtual machine"

BAPI for BOM download

Hi Guys,
I was trying to download BOM from R/3 to SAP CRM , can any one help me to let me know do we have any BAPI given by SAP to do this, if yes i would like to get their names.
Rgds
Kiran

Re: Configurable Product

How to avoid configuration product downloading from R/3 into CRM

Hello,
We have CRM 4.0 connected with R/3 backEnd and configurable products are downloading from R/3 into CRM with the whole characteristics.
We don´t use this characteristics in CRM to configure this product and the pricing. Is there any way to avoid this information into CRM??
1.- Though the Middleware???
2.- Though the Uninstalling IPC(internet pricing configurator)???
3.- though the item category of the Business Transaction.???
It´d be grateful to get a way because actually, when we enter the product, this one has to be configurated because of the errors.
Thanks a lot,
Luis Angel Fernández

Hello Luis,
First of all I am unable to understand how are you getting the characteristic through material download.
All configuration comes through Knowledge Base and its runtime version.
If you want to block configurable materials from flowing to CRM then set the filter on Item Category Group.
I think you must have different item Category group for configurable material.
Thanks & Regards
Subhabrata

Variant Configuration Data download from R/3 to CRM

Hello all
It may be a very dumb question, but I would certainly appreciate an answer.
We are currently using SAP R/3 4.6c and heavily use VC for configurable products and also for pricing.
Now we wish to explore the possibility of using SAP CRM 5.0 to enable our sales force to use CRM PCUI to create quotes for configurable materials.
My questions are as following:-
1. Is it possible to download all VC related data into CRM from R/3 including pricing? I understand that for different VC object, I will have to use different CRM objects but is it possible? If the data transfer is possible, is it typically done by a middleware resource?
2. I would also like to confirm that by creating a run time version and Kbase is pre requisite to enable the download to CRM.
If you could please point me to the appropriate help on this topic, I would really appreciate it.
Best regards
Jai

Hi Gun,
In your message, You stated
As recommended by SAP, if we have R/3 link into our CRM
the best scenario is to get VC product from R/3 into CRM.
Is there any documentation tjhat backs this up? could you give it to me
we have a situation in our company where we have been using a home grown product that not only lets you configure product bu it also takes the user through a selling experience for example it asks the user if he is interested in buying any accessories for the product and provides options through pop messages and the user can select. this way it takes leads the user through questionnaires that comes in pop ups to select a product
we have crm service and ecc implemented and now we need to implement this feature for the crm sales piece
the question is do we go for PME or variant config that is already set up in ECC ?
the link and middle ware set up between ECC and CRM is also available so we can bring the variant configuration from ECC into crm. but how about the questionnaires and the selling experience that is available through pop up questionnaires,
we can set up the selling experience via the Product modeler but as a company we need to make a decision whether we bring the varinat configuration from ecc and use the selling experience for the pop up questionnaires that leads customer
or should we just use sales packages that behaves similarly like varinat configuration and add enahcnements to create the pop- up questionaires
Could you direct /provide some guidance in this area?
Sara

Why are itunes hd movies only available in 720p in Portugal and Spain, instead of 1080p :-( (yes, my itunes is configured to download content in 1080p)?

I have checked other itunes stores, and 1080p is available in almost all other european countries, including Greece and Italy.
This is really disapointing, especially considering that portuguese cable TV service providers "offer" these movies at lower rates.
Doies anyone know when will this issue be "solved".
Thank you in advance.
br
Tiago

Hello billwoodard11,
Thanks for the question. If your computer is not compatible with HD 1080p content, you should receive a prompt stating so - but should still be able to download the content for use on other devices. For more information, check out this resource:
Purchasing and viewing HD videos in iTunes - Apple Support
http://support.apple.com/en-us/HT201850
How to purchase, download, or view HD 1080p content
iTunes 10.6 by default is set to purchase, download, and playback HD content in 720p. You must change your local preference setting if you prefer to download, purchase, and playback HD content in 1080p. Depending on your computer's hardware configurations, you may be unable to purchase, rent, or playback content in 1080p. iTunes may display the following dialog:
On Mac or PC
Download the latest version of iTunes. You can download iTunes for free.
From the iTunes menu, choose iTunes > Preferences > Store (for PC, choose Edit > Preferences > Store).
Next to "When downloading High Definition videos, prefer:" set your preference to 1080p1.
Click OK. Now, when you purchase or download HD content, your computer will always download in 1080p, when available.
Depending on your computer's hardware limitations, you may be unable to purchase, rent, or view HD content from the iTunes Store. If you are trying to view HD video on an external display, the display must have a digital connection (DVI, DisplayPort, or HDMI) and support HDCP.
Check out the following resource for information on downloading past purchases, including information on playing purchases on Apple TV:
Download past purchases - Apple Support
http://support.apple.com/en-us/HT2519
Thanks,
Matt M.

Variant configuration BOM

Hi
Please tell me type of BOM in Variant Configuration? When and where it should use. ?
How to comfigured ?

close

Configurable BOM download

Similar Messages

Maybe you are looking for