Configuracion air-cap 1131 AG

quickie tell them so I'm trying to Configure an Access Point 1131 Air Cap AG But instantly connecting portion I do not hyper terminal detects the command configure terminal Someone has past him 
thank you very much in advance
les comento asi rapidito Estoy tratando de Configurar ONU Acces Point Aire Cap 1131 AG Pero Al Momento de conectarlo Porción hiperterminal no me Detecta el comando configure terminal a Alguien le ha Pasado 

refer
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/1130/installation/guide/1130-TD-Book-Wrapper/113h_c4.html

Similar Messages

  • WLC 5508 and AIR CAP 1602I

    Hello,
    We've got a problem with the AP (AIR CAP 1602I) which is managed by WLC 5508(7.4.100.60)
    Users connect to the AP with VOIP phones(Avaya).. and there are following problems during calls
    -robot voice
    -strong noise(even if call is not made, just speaker is on)
    Strange thing is that there is no problem with older APs which are managed with the same WLC.
    Any idea?
    Thanks in advance

    Well that can be a cause also. I would look at using 7.4.110.0 which is MR1. If that doesn't help, then open a TAC case as it might be something else. Going to v7.5 I don't think will fix the issue.
    Many times I would go the the manufacture and find out if the support a certain code or not. It's nice when they do test to make sure it still works. Some manufactures do test and will suggest code versions and that's when you have to decide if the 1602 was really needed or just keep adding 1262's since there was only 3 added.
    Sent from Cisco Technical Support iPhone App

  • Cisco AIR-LAP 1131 reboot in loop

    Hi Everyone
    I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
    Unexpected exception to CPUvector 1100, PC = 5A9048
    -Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
    Exception (1100)! Data TLB Miss
    SRR0 = 0x005A9048  SRR1 = 0x00029230  SRR2 = 0x0028007C  SRR3 = 0x00021230
    ESR = 0x00000000  DEAR = 0x025BFB94  TSR = 0x84000000  DBSR = 0x00000000
    CPU Register Context:
    Vector = 0x00001100  PC = 0x005A9048  MSR = 0x00029230  CR = 0x53000035
    LR = 0x0048A8A0  CTR = 0x00000072  XER = 0xA0000040
    R0 = 0x00000072  R1 = 0x00CD9790  R2 = 0x00000000  R3 = 0x025CBFF8
    R4 = 0x025BFB94  R5 = 0x00000000  R6 = 0x00000001  R7 = 0x000000C3
    R8 = 0x000001C8  R9 = 0x00000000  R10 = 0x025CBFF8  R11 = 0x00000000
    R12 = 0x00CDB580  R13 = 0x00000000  R14 = 0x00000000  R15 = 0x00000000
    R16 = 0x0184C8AA  R17 = 0x0184C71B  R18 = 0x00CDB760  R19 = 0x00000007
    R20 = 0x00000001  R21 = 0x00000000  R22 = 0x00000007  R23 = 0x00000001
    R24 = 0x0093BA68  R25 = 0x00000000  R26 = 0x00000001  R27 = 0x00000001
    R28 = 0x00001FA8  R29 = 0x0094A200  R30 = 0x01C7FE38  R31 = 0x00003D80
    Stack trace:
    PC = 0x005A9048, SP = 0x00CD9790
    Frame 00: SP = 0x00CD97D0    PC = 0x0048A6A8
    Frame 01: SP = 0x00CDB728    PC = 0x004361FC
    Frame 02: SP = 0x00CDB740    PC = 0x0042E078
    Frame 03: SP = 0x00CDB758    PC = 0x0044880C
    Frame 04: SP = 0x00CDB798    PC = 0x0042A280
    Frame 05: SP = 0x00CDB7C0    PC = 0x0042AA68
    Frame 06: SP = 0x00000000    PC = 0x0018A990
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    St-John-AP1 uptime is 1 minute,
    cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
    Processor board ID FTX1632N00D
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    And this is all it does, and keep loading the image. I already know the recovery procedure to reset it, but i wanted to know how i can put these AP in HREAP without having these issues. In the setup we need, we cannot have those AP be in local mode.
    Thanks for any help and consideration .
    Regards

    Hi Scott
    Thanks for replying
    here is the full output between loops :
    Press RETURN to get started!
    *Mar  1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:09.281: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    *Mar  1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
    *Mar  1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar  1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
    *Mar  1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
    *Mar  1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
    Translating "CISCO-LWAPP-CONTROLLER.aimfire.net"...domain server (10.1.10.100) [OK]
    *Mar  1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
    *Mar  1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar  1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
    *Mar  1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
    *Mar  1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed sta
    15:52:12 UTC Fri Mar 1 2013: Unexpected exception to CPUvector 1100, PC = 0x5A9048  , LR = 0x48A8A0
    -Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
    CPU Register Context:
    MSR = 0x00029230  CR  = 0x53000035  CTR = 0x00000072  XER   = 0xA0000040
    R0  = 0x00000072  R1  = 0x00D1EC18  R2  = 0x00000000  R3    = 0x025CBFF8
    R4  = 0x025BFB94  R5  = 0x00000000  R6  = 0x00000001  R7    = 0x000000CA
    R8  = 0x000001C8  R9  = 0x00000000  R10 = 0x025CBFF8  R11   = 0x00000000
    R12 = 0x00D20A08  R13 = 0x00000000  R14 = 0x00000000  R15   = 0x00000000
    R16 = 0x01851A6A  R17 = 0x018518DB  R18 = 0x00D20BE8  R19   = 0x00000007
    R20 = 0x00000001  R21 = 0x00000000  R22 = 0x00000007  R23   = 0x00000001
    R24 = 0x0093BA68  R25 = 0x00000000  R26 = 0x00000001  R27   = 0x00000001
    R28 = 0x00001FA8  R29 = 0x0094A200  R30 = 0x01C7FE38  R31   = 0x00003D80
    Writing crashinfo to flash:/crashinfo_20130301-155213
    === Flushing messages (15:52:20 UTC Fri Mar 1 2013) ===
    Buffered messages:
    *Mar  1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:09.281: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    *Mar  1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
    *Mar  1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar  1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
    *Mar  1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
    *Mar  1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
    *Mar  1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
    *Mar  1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar  1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
    *Mar  1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
    *Mar  1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed state to UP
    *Mar  1 15:52:11.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    Queued messages:
    *Mar  1 15:52:23.534: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
    *Mar  1 15:52:11.414: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    Nested exception_rom_monitor call (2 times)
    Unexpected exception to CPUvector 1100, PC = 5A9048
    -Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
    Exception (1100)! Data TLB Miss
    SRR0 = 0x005A9048  SRR1 = 0x00029230  SRR2 = 0x0028007C  SRR3 = 0x00021230
    ESR = 0x00000000  DEAR = 0x025BFB94  TSR = 0x84000000  DBSR = 0x00000000
    CPU Register Context:
    Vector = 0x00001100  PC = 0x005A9048  MSR = 0x00029230  CR = 0x53000035
    LR = 0x0048A8A0  CTR = 0x00000072  XER = 0xA0000040
    R0 = 0x00000072  R1 = 0x00D1EC18  R2 = 0x00000000  R3 = 0x025CBFF8
    R4 = 0x025BFB94  R5 = 0x00000000  R6 = 0x00000001  R7 = 0x000000CA
    R8 = 0x000001C8  R9 = 0x00000000  R10 = 0x025CBFF8  R11 = 0x00000000
    R12 = 0x00D20A08  R13 = 0x00000000  R14 = 0x00000000  R15 = 0x00000000
    R16 = 0x01851A6A  R17 = 0x018518DB  R18 = 0x00D20BE8  R19 = 0x00000007
    R20 = 0x00000001  R21 = 0x00000000  R22 = 0x00000007  R23 = 0x00000001
    R24 = 0x0093BA68  R25 = 0x00000000  R26 = 0x00000001  R27 = 0x00000001
    R28 = 0x00001FA8  R29 = 0x0094A200  R30 = 0x01C7FE38  R31 = 0x00003D80
    Stack trace:
    PC = 0x005A9048, SP = 0x00D1EC18
    Frame 00: SP = 0x00D1EC58    PC = 0x0048A6A8
    Frame 01: SP = 0x00D20BB0    PC = 0x004361FC
    Frame 02: SP = 0x00D20BC8    PC = 0x0042E078
    Frame 03: SP = 0x00D20BE0    PC = 0x0044880C
    Frame 04: SP = 0x00D20C20    PC = 0x0042A280
    Frame 05: SP = 0x00D20C48    PC = 0x0042AA68
    Frame 06: SP = 0x00000000    PC = 0x0018A990
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    St-John-AP1 uptime is 1 minute, 7 seconds
    cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
    Processor board ID FTX1632N00D
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    flashfs[0]: 40 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 15129600
    flashfs[0]: Bytes available: 869376
    flashfs[0]: flashfs fsck took 41 seconds.
    Base ethernet MAC Address: d8:67:d9:ba:9f:2e
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ethernet link up, 100 mbps, full-duplex
    Ethernet port 0 initialized: link is up
    Loading "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2"...###############################################
    File "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    Image text-base: 0x00003000, data-base: 0x005AEE20
    Initializing flashfs...
    flashfs[1]: 40 files, 3 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 15998976
    flashfs[1]: Bytes used: 15129600
    flashfs[1]: Bytes available: 869376
    flashfs[1]: flashfs fsck took 5 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    Radio 1 A506 7100 E8000000 A0000000 80000000 3
    Radio 0 0 0 0 0 0 2
    cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
    Processor board ID FTX1632N00D
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from unknown reload cause - reason ptr 0xF, PC 0x5A9048, address 0x0
    LWAPP image version 4.1.192.35
    1 FastEthernet interface
    1 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: D8:67:D9:BA:9F:2E
    Part Number                          : 73-13304-02
    PCA Assembly Number                  : 800-36409-01
    PCA Revision Number                  : B0
    PCB Serial Number                    : FOC16304BZJ
    Top Assembly Part Number             : 800-29582-03
    Top Assembly Serial Number           : FTX1632N00D
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1131G-A-K9
    Press RETURN to get started!
    Also , the switchport is a trunk port, i can definitely try it an access port .

  • Air-lap-1131-ag-e-k9 convert to autonomous not working

    Hi,
    i have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
    i have followed numerous guides on this forum, i have successfully
    downloaded correct firmware
    renamed the firmware to .default
    placed this in root of tftp server folder
    connected laptop via console to view output
    connected laptop via Ethernet to Ethernet port of AP
    changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
    held reset button on AP when applying power and waiting for radio light to flash red
    AP gets a IP address then of 10.0.0.1
    But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
    I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
    i acquired the AP for training purposes to help with studies and so far i have learnt a lot of troubleshooting but i would really love to get past this, any help would be really appreciated.
    Kind regards
    Sam

    Xmodem file system is available.
    flashfs[0]: 29 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 7215616
    flashfs[0]: Bytes available: 8783360
    flashfs[0]: flashfs fsck took 31 seconds.
    Base ethernet MAC Address: 00:1e:f7:ed:b5:46
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ethernet link up, 100 mbps, full-duplex
    Ethernet port 0 initialized: link is up
    button pressed for 20 seconds
    process_config_recovery: set IP address and config to default 10.0.0.1
    process_config_recovery: image recovery
    image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
    examining image...
    %Error opening  (no such file or directory)Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...#########################################################################################################################################################################
    File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 17-Jul-06 11:38 by alnguyen
    Image text-base: 0x00003000, data-base: 0x0035E440
    Initializing flashfs...
    flashfs[1]: 29 files, 9 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 15998976
    flashfs[1]: Bytes used: 7215616
    flashfs[1]: Bytes available: 8783360
    flashfs[1]: flashfs fsck took 4 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
    Processor board ID FCZ1222Q27A
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    LWAPP image version 3.0.51.0
    1 FastEthernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:1E:F7:ED:B5:46
    Part Number                          : 73-8962-12
    PCA Assembly Number                  : 800-24818-11
    PCA Revision Number                  : B0
    PCB Serial Number                    : FOC122106TU
    Top Assembly Part Number             : 800-29144-02
    Top Assembly Serial Number           : FCZ1222Q27A
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1131AG-E-K9
    Press RETURN to get started!
    *Mar  1 00:00:06.280: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
    *Mar  1 00:00:06.289: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 17-Jul-06 11:38 by alnguyen
    *Mar  1 00:00:07.238: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:08.238: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:09.642: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
    *Mar  1 00:00:25.297: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar  1 00:00:36.237: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up

  • Cant Connect Cisco AIR-CAP 3602 with 2504 controller

    Im trying to have one of our APs join our controller. No matter what I do, i cant get it to join the controller.
    The controller has the right OS, I had to upgraded it 7.4 to support the 3600...
    Both the controller and the AP has the same time and date.
    But Im getting this from my AP:
    *Oct 30 14:49:26.043: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Oct 30 14:49:26.067: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:26.083: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:27.055: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:27.095: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Oct 30 14:49:27.103: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Oct 30 14:49:28.087: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:28.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Oct 30 14:49:28.131: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:28.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:28.147: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Oct 30 14:49:29.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:29.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:29.167: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:30.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:36.083: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 30 14:49:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 14:49:36.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 14:49:36.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
    Anyone can help me please?
    Thanks....

    AP is connected directly to one of the ports on the 2504 controller.
    I can move it to a POE switch, if needed.
    Here is the output after I boot up the AP:
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Macronix Mirrorbit (00C2)
    Xmodem file system is available.
    flashfs[0]: 43 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 16767488
    flashfs[0]: Bytes available: 15230464
    flashfs[0]: flashfs fsck took 16 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 4c:00:82:77:32:7b
    Ethernet speed is 1000 Mb - FULL Duplex
    Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1"...###########################
    File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 43 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 16767488
    flashfs[0]: Bytes available: 15230464
    flashfs[0]: flashfs fsck took 8 seconds.
    Base Ethernet MAC address: 4c:00:82:77:32:7b
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1;flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1'
    Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1"...###############################
    File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 22:57 by prod_rel_team
    Initializing flashfs...
    flashfs[3]: 43 files, 9 directories
    flashfs[3]: 0 orphaned files, 0 orphaned directories
    flashfs[3]: Total bytes: 31739904
    flashfs[3]: Bytes used: 16767488
    flashfs[3]: Bytes available: 14972416
    flashfs[3]: flashfs fsck took 8 seconds.
    flashfs[3]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 11999232
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 11998208
    flashfs[4]: flashfs fsck took 1 seconds.
    flashfs[4]: Initialization complete.
    Copying radio files from flash: to ram:
    Copy in progress...CCCCC
    Copy in progress...CCC
    Copy in progress...CCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Uncompressing radio files...
    ...done Initializing flashfs.
    Radio0  present 8764 8000 0 A8000000 A8010000 0
    Rate table has 244 entries (64 SGI/104 BF variants)
    Radio1  present 8764 8000 0 88000000 88010000 4
    Radio2 not present 0 0 0 0 0 8
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP3602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
    Processor board ID FTX1731GQYY
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.5.102.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 4C:00:82:77:32:7B
    Part Number                          : 73-14521-02
    PCA Assembly Number                  : 800-37501-02
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC17273HG4
    Top Assembly Part Number             : 800-35852-02
    Top Assembly Serial Number           : FTX1731GQYY
    Top Revision Number                  : C0
    Product/Model Number                 : AIR-CAP3602I-A-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:11.355: FIPS IOS test Image Checksum successful
    *Mar  1 00:00:11.355: FIPS IOS test Crypto RNG DEK Key Test successful
    *Mar  1 00:00:11.355: FIPS IOS test SHA-1 successful
    *Mar  1 00:00:11.355: FIPS IOS test HMAC-SHA1 successful
    *Mar  1 00:00:11.355: FIPS IOS test AES CBC 128-bit Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test AES CBC 128-bit Decrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS AES CMAC Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS CCM Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS CCM Decrypt successful
    *Mar  1 00:00:11.387: FIPS IOS test RSA Signature Generation successful
    *Mar  1 00:00:11.391: FIPS IOS test RSA Signature Verification successful
    *Mar  1 00:00:11.391: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:11.391: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
    *Mar  1 00:00:11.847: Registering HW DTLS
    *Mar  1 00:00:14.647: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:26.811: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 22:57 by prod_rel_team
    *Mar  1 00:00:26.811: %SNMP-5-COLDSTART: SNMP agent on host AP4c00.8277.327b is undergoing a cold start
    *Jul  4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Jul  4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Jul  4 23:55:50.051: %PARSER-4-BADCFG: Unexpected end of configuration file.
    lwapp_crypto_init: MIC Present and Parsed Successfully
    *Jul  4 23:55:50.191: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Jul  4 23:55:50.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Jul  4 23:55:51.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Jul  4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Jul  4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Jul  4 23:55:53.319: FIPS HW test SHA-1 successful
    *Jul  4 23:55:53.319: FIPS HW test HMAC-SHA1 successful
    *Jul  4 23:55:53.319: FIPS HW test AES CBC 128-bit Encrypt successful
    *Jul  4 23:55:53.319: FIPS HW test AES CBC 128-bit Decrypt successful
    *Jul  4 23:55:53.819: FIPS HW test SHA-1 successful
    *Jul  4 23:55:53.819: FIPS HW test HMAC-SHA1 successful
    *Jul  4 23:55:53.819: FIPS HW test AES CBC 128-bit Encrypt successful
    *Jul  4 23:55:53.819: FIPS HW test AES CBC 128-bit Decrypt successful
    *Jul  4 23:55:53.819: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
    *Jul  4 23:55:53.819: DPAA Initialization Complete
    *Jul  4 23:55:53.819: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Jul  4 23:55:54.819: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up%Default route without gateway, if not a point-to-point interface, may impact performance
    *Jul  4 23:56:13.191: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Jul  4 23:56:14.279: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Jul  4 23:56:15.279: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Jul  4 23:56:15.371: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Jul  4 23:56:16.371: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Jul  4 23:56:18.895: Logging LWAPP message to 255.255.255.255.
    *Jul  4 23:56:23.627: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.1.150, mask 255.255.240.0, hostname AP4c00.8277.327b
    Translating "CISCO-CAPWAP-CONTROLLER.pti.local"...domain server (10.3.1.32)
    *Jul  4 23:56:34.559: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Jul  4 23:56:34.567: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.pti.local
    *Jul  4 23:56:44.567: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 30 15:05:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 15:05:13.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 15:05:13.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
    *Oct 30 15:05:18.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50

  • Air-cap 3502i White LED no console output

    On our department We have 36 lightweight AP 3502i  v02 out of the 36 ap only 7  are working fine. And the rest has white LED and no console output, all the AP that working fine are v01.
     Basic on the information in the link below, the access points with v02 should be fine. I wondering if anyone who has the same problem with these software or access points.
    PID: AIR-CAP3502I-A-K9
    VID : v01 , v02
    15.2(2)JAX ver
    http://www.cisco.com/c/en/us/support/docs/field-notices/635/fn63537.html
    thank you 

    Never saw that before, since when are you running into this problem?
    In the 3500 documentation there is no explanation given for the white LED status, so I guess that you have to file a TAC case. The 3500 access-points have limited lifetime warranty, so if they are broken you will receive new ones in about 10 business days (much faster if you have smartnets on them, but not a lot of people do this).

  • Air-Cap 3501

    Just got a Cisco 3501 AP, Did not know it required such complex configuration. If someone could/would help out. here is what I am asking
    I have a cisco 3650 switch NICE- It has the controller for this wireless AP>  I have no ideas how to set that up, unable to find resources on-line. However I found this section in the documentation 
    option 43 hex <hex string>
    The hex string is assembled by concatenating the TLV values shown below:
    Type + Length + Value
    Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex. Value is the IP address of the controller listed sequentially in hex.
    For example, suppose that there are two controllers with management interface IP addresses, 10.126.126.2 and 10.127.127.2. The type is f1(hex). The length is 2 * 4 = 8 = 08 (hex). The IP addresses translate to 0a7e7e02 and 0a7f7f02. Assembling the string then yields f1080a7e7e020a7f7f02. The resulting Cisco IOS command added to the DHCP scope is option 43 hex f1080a7e7e020a7f7f02.
    How do I make the conversion of this equation. Its tells you here to do but not how to do it. Also the controller setup. I cant find anything one this. 
    Maybe this AP is not worth the effort ? 
    Thanks Please be judgment free This is my first time here, So if this post is done wrong.. Sorry on that .

    Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex. Value is the IP address of the controller listed sequentially in hex.
    For example, suppose that there are two controllers with management interface IP addresses, 10.126.126.2 and 10.127.127.2. The type is f1(hex). The length is 2 * 4 = 8 = 08 (hex). The IP addresses translate to 0a7e7e02 and 0a7f7f02. Assembling the string then yields f1080a7e7e020a7f7f02. The resulting Cisco IOS command added to the DHCP scope is option 43 hex f1080a7e7e020a7f7f02.
    Don't "re-invent the wheel":  Go HERE.

  • AIR-CAP-3702E-E

    Hi,
    Can a Cisco CAP3702E-E be converted to a stand-alone AP, if yes, what will be the procedure.

    Using a TFTP Server to Return to a Previous Release

  • Configuration en Autonome AP AIR-CAP 1600I

         j'ai besoins d'aide pour la configuration en autonome de l'AP 1600.

    Take a look at this link:
    http://www.cisco.com/c/en/us/support/wireless/aironet-1600-series/products-configuration-examples-list.html
    Thanks,
    Scott
    *****Help out other by using the rating system and marking answered questions as "Answered"*****

  • AIR CAP 3602E-E-K9 NEW AUTONOMOUS IOS CAN,T LOAD PROPERLY DEVICE IS NOW IN AP MODE

    ap: boot
    Loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"...flash:/ap3g2-
    k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1: no such file or directory
    Error loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"
    Interrupt within 5 seconds to abort boot process.
    Loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1"...#############
    File "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1" uncompressed and i
    nstalled, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Xmodem file system is available.
    ap: boot
    Loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"...flash:/ap3g2-
    k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1: no such file or directory
    Error loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"
    Interrupt within 5 seconds to abort boot process.
    Unable to locate IOS image with name **xx**.
    Boot CMD: 'flash:/ap3g2-k9w7-xx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1'
    Loading "flash:/ap3g2-k9w7-xx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1"...flash:/ap3g2-
    k9w7-xx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1: no such file or directory
    Error loading "flash:/ap3g2-k9w7-xx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1"
    Interrupt within 5 seconds to abort boot process.
    Boot process failed...
    ap:
    ap:
    ap:
    DEVICE IS NOW IN AP MODE  HOW CAN I EASILY LOAD ANOTHER IOS............................TELL ME SOME AP MODE COMMANDS

    Please goes a long way matey :-).
    The experts can probably correct me here but it looks like your IOS is in  "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1" and your AP is trying to boot from: "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"
    So firstly, try using the following command:
    set boot flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1
    then issue the 'boot' command and see if that works.
    If not, grab a copy of your IOS and setup a TFTP server connected to your Access Point. You may need to turn off your personal firewall when you do this.
    Follow the instructions at this link which explain it on an 1142 which should be the same method:
    https://supportforums.cisco.com/docs/DOC-14636
    Let us know how you go!

  • Can I configure Cisco 1602i (AIR-CAP1602I-T-K9) in Standalone mode ?

    Hi everybody, please, i need some help here.
    I bought 3 Cisco 1602i (AIR-CAP1602I-T-K9) but I didn't bought a Controller. How can I configure then in Standalone mode ?
    I Saw in other forums, i need to change the IOS Software to an Autonomous Software. They suggested the ap1g2-k9w7-tar.152-4.JA1.tar. I would like to know if it is the right software and if there is any problem with licensing if i download and use it.
    Explanation of the differences between AIR-CAP-1602i-x-K9 e AIR-SAP-1602i-x-K9
    http://community.spiceworks.com/topic/448208-cisco-aironet-1602i-questions-issues
    How to convert to IOS autonomous
    http://www.experts-exchange.com/Networking/Wireless/Q_28245190.html
    IOS Download:
    http://software.cisco.com/download/release.html?mdfid=284366503&softwareid=280775090&release=15.2.4-JA1&flowid=37523
    Thanks.
    Wesley

    Hi,
    Yes you must need to change to autonomous mode.Yes it is the right software and you will not face any problem regarding license.
    But for download the autonomous AP image from cisco you need a CCO (Cisco login) and valid service contract .
    Here is the latest image:Can download from here
    http://software.cisco.com/download/release.html?mdfid=284366503&flowid=37523&softwareid=284180979&release=15.2.4-JB5&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    How to covert from lAP to autonomous :
    http://www.youtube.com/watch?v=QQ_NuxdRhQ4
    http://rscciew.wordpress.com/2014/05/07/access-point-conversion-lap-to-aap-and-vice-versa/
    Regards
    Dont forget to rate helpful posts

  • Cap lock stuck

    My MacBook Air caps lock is stuck on the on position and since my password is in lower case I can't sign in. The key is not physically stuck but remains in caps on .. Any suggestions

    This forum is actually about the Cloud, not about using individual programs
    For product specific questions you will do better in the specific product forum
    If you start at the Forums Index http://forums.adobe.com/index.jspa
    You will be able to select a forum for the specific Adobe product(s) you use
    Click the "down arrow" symbol on the right (where it says ALL FORUMS) to open the drop down list and scroll
    http://forums.adobe.com/community/photoshop

  • 2 WLCS for failover

    Hi,
    I want to buy a second WLC. The equipment hasn't been ordered yet so I just trying to think a head.
    As I understand it if I buy the second WLC and put it in the same mobility group then enable AP fallback that is all I have to do. Is that really it? They will be 2504's. The APs are Air Cap 36021-A-k9.
    What about adding the access points etc etc does that happen automatically and the config gets replicated? Again sorry to ask what might be a stupid question for many but I really know very little about wireless at the moment.
    Also is there an idiots guide somewhere for setting up guest wireless lans?
    Thanks,

    Consider a scenario where there are two Wireless LAN Controllers (WLCs) named WLC1 and WLC2. These WLCs are configured in the same subnet in one WLAN. In order to achieve high availability, this is how the WLAN is configured:
    WLC1 and WLC2 are configured within the same mobility      group.
    Half of the access points are configured to use WLC1 as      the primary WLC and use WLC2 as the secondary WLC.
    The other half of the access points are configured to      use WLC2 as the primary WLC and use WLC1 as the secondary WLC.
    The fallback feature is enabled on both WLC1 and WLC2.
    Network Diagram
    Resolution
    If any of the WLCs go down, the access point that is joined to the failed WLC  recognizes this (keep alive (heartbeat) between access point and WLC). Therefore, the access point begins to join the good WLC, which still runs. This is not stateful failover, which means that the access point has to join the new WLC and therefore the wireless clients.
    Also, if either of the WLCs do not work and the affected access points re-register to the other WLC, then the wireless clients have to re-associate and therefore lose wireless connection during failover as it is not stateful failover. The failover is not transparent to the WLAN client. That is, the WLAN clients lose their WLAN connectivity during access point failover.
    Access points and clients are not effected on the WLC that runs. This means that the fallback of the access point is not transparent to the clients. Only access points and clients on the failed WLC are effected.
    In order to configure the WLAN Controller failover for Lightweight Access points, the Access Point must be configured correctly in a mobility group for the AP failover and each Wireless LAN Controller (WLC) must have the AP failover feature enabled.
    Configure the Fallback Feature on WLC
    The last step is to configure the Fallback feature on the controller. This feature ensures that the AP switches return to the first WLC when the WLC that comes back on line. Complete these steps:
    From the GUI, choose Controller > General.A      list of options appears on the General screen.
    For the AP Fallback option, choose Enabled from      the drop-down menu.
    Click Apply.Note: It is sufficient to      enable the Fallback feature on the secondary controller alone. But it is      recommended to configure it on the primary WLC as well because it can be      configured as a secondary controller for other access points
    http://www.cisco.com/image/gif/paws/69639/wlc_failover-12.gif
    After you complete these steps, the setup is configured for WLC failover. When the primary controller (WLC-1, in this case) goes down, the APs automatically get registered with the secondary controller (WLC-2). The APs register back to the primary controller when the primary controller comes back on line. AP switching between the primary and secondary controllers also affects the wireless clients associated with these APs.
    In controller software release 5.1.151.0, you can configure the wireless network so that the backup controller recognizes a join request from a higher-priority access point and, if necessary, disassociates a lower-priority access point as a means to provide an available port. In order to configure this feature, failover priority must be enabled on the network and assign priorities to the individual access points. By default, all access points are set to priority level 1, which is the lowest priority level.
    Note: Be aware that Failover priority takes effect only if there are more association requests after a controller failure than there are available backup controller ports.
    Wireless LAN Controller Failover Priority
    During installation, Cisco recommends you connect all lightweight access points to a dedicated controller, and configure each lightweight access point for final operation. This step configures each lightweight access point for a primary, secondary, and tertiary controller and allows it to store the configured mobility group information. When sufficient controllers are deployed, if one controller fails, active access point client sessions are momentarily dropped while the dropped access point associates with another controller, which allows the client device to immediately reassociate and reauthenticate.
    You can also follow the below link(WLAN Controller Failover for Lightweight Access Points Configuration Example)
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008064a294.shtml

  • Exe build error involvving internal.llb

    Hi all,
    I have built many exe's, but for some reason this one is being difficult!  I get an error which states:
    Error 1003 occurred at \\Rochester\mtp\Test Rigs\NC4\NC4 Air Cap\Code Development\Air cap v2.0\exe\internal.llb\Air Cap inspection Rig v2.1.vi
    I have reviewed many forum posts which suggest that one of the sub vi's is not executable.  The main vi and all of the sub-vi's will execute in the labview environment.  I have tried a forced compile and even a mass compile.  All to no avail.  This problem occurs on two different PC's and other similar vi's build fine, so I assume it is not a problem with the builder.
    I am using LabVIEW 7.1, Vision 8.0 and IMAQ 3.5.1: see attached report for good measure.
    Can you help?
    If you need the sub vi's let me know.
    Dan
    Solved!
    Go to Solution.
    Attachments:
    Air Cap inspection Rig v2.1.vi ‏253 KB

    HI Dan,
    Thank you for your post, I have been investigating into your issue and the error code 1003 means:
    1003
    The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the VI in LabVIEW using File»Open And verify that it is runnable.
     This may occur because one of your variables is spelt slightly different to what the code is expecting, or because one of your enum typedefs has an empty element.
     By any chance are you using Microsoft word, Excel, RT, or the report generation toolkit?  
     If so you need to include more files to make it work as an .exe.
    Also it may help if you:
    Enter the ‘my advanced properties’
    Check the Enable debugging option in the Advanced category of the application executable properties.
    Uncheck the Disconnect type definitions and remove unused polymorphic VI instances.
    Here are some links that may help you:
    http://digital.ni.com/public.nsf/allkb/C79C2050F520BC4F86256D96007CF35F?OpenDocument 
    http://digital.ni.com/public.nsf/allkb/705C2ECA081F3C7986256C0F00559B02 
    If these can’t help could you please send a screenshot of the error message and section of code.
    I have also noticed that you have posted this on another forum page please could you reframe from double posting in future. http://forums.ni.com/ni/board/message?board.id=170&message.id=357791
     Regards,  
    Message Edited by J POWER on 10-06-2008 05:35 AM
    Jordan Power
    Applications Engineer
    National Instruments

  • WLC ethernet bridge

    Hi,
    I've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.
    I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.
    The switch port that is connected to the RAP and MAP is configured as the following:
    switchport mode trunk
    switchport trunk native vlan 2
    switchport trunk allowed vlan 10,20,30,40
    The RAP etherbridge port is enable and set to: normal
    The MAP etherbridge port is enable and set to: Trunk,
    native vlan is set to: 2
    Vlan id 10
    Vlan id 20
    The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.
    Could someone please tell me what I'm doing wrong?
    　

    I would open a TAC case as this is a bug. I don't recall what code it stopped working but I know it doesn't work also in the v7.3 & v7.4
    Sent from Cisco Technical Support iPhone App

Maybe you are looking for

  • F4 help for month and Year field in ztable please

    I have created a ztable.  The first field in my ztable is a primary key field and it holds MM/YYYY(eg.  08/2011). How ever my requirement is when ever we want to see the output, uer wants F4 help on that fields and when he selects the range , the zta

  • GP: How to keep action  sleeping until ABAP function module raises event

    Hello experts, I'd like to develop a gp process which contains a callable objects which keeps the process instance waiting until an abap function module send something like an event. I don't want to put too much load on the machine and block expensiv

  • Value Mapping Replication from BPM

    Hi, I'm trying to maintain some value mapping replication data from a BPM. Based on certain steps and their results, a Value Mapping Replication message is sent from BPM. I configured the the receiver as XI system and used the XI channel with java pa

  • RFC in Local system

    Hi can we use RFC without network system. is there any possibilities to use virual server to perform the task locally. thanks

  • Date and time lost

    seems that everytime I reboot this G4 macbook I need to reset the time and date. Is there somewhere to make the time and date stick?