Configurar smtp en cisco RV110W for scan spiceworks

Configurar smtp en cisco RV110W for scan spiceworks
This topic first appeared in the Spiceworks Community

Hi,
Could you please try to put another DNS server on the ESA? Like ISP's DNS or a public one.
Luis Silva

Similar Messages

Alarm smtp in cisco prime

Hi,
I want to configure the smtp in cisco prime for receive alarm message in my account .than ,when i press the test button ,the following message is display.
Failed to send mail to primary SMTP server. Please make sure that you save mail configuration by hitting 'Save' button.
think's

http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/1-2/user/guide/prime_infra_ug/maint_sys_health.html#pgfId-1059487

Trustwave PCI scan failed for scan interference on Sonicwall NSA E5500 firewall

We've started having Trustwave do monthly PCI network vulnerability scans. The last couple months we've passed, but this month it failed for "Scan Interference Detected." This is their recommendation:During the course of the scan, TrustKeeper detected a change in its ability to communicate with some services on the remote host. In some cases, this may be caused by network security devices actively blocking the vulnerability scan, which it may perceive as a threat. In other cases, an intermediate network device, or the host itself, may be unable to cope with the vulnerability scan.It's often very difficult to tell the difference between these two scenarios, but in either case, this behavior significantly impacts the ability of this vulnerability scanning service to detect vulnerabilities on the remote host, resulting in an inconclusive...
This topic first appeared in the Spiceworks Community

You're correct that the RV042 router's implementation of SSL is weak.
Stepping back, why do you need an SSL key on your router? Assuming there's a good reason that can't be met via other techniques, can you implement a compensating control (such as an ACL) to mitigate the risk and thus meet that compliance requirements?
If not, then you would need to move the function to a more secure device - the new ASA 5506 might be one such candidate. Your local Cisco partner should be able to help you with product selection based on a more in-depth analysis of your environment and requirements

HP laserjet 100 color MFP M175nw -Driver for scanning in windows 8.1??

scanner doesn't work since installing windows 8.1. Doctor for scanning and printing want's me to install new driver.
But I can't find it.
Hope I've missed it

H beermans
I understand you are no longer able to scan since updating to Win 8.1.
Uninstall and reinstall the Win 8 driver again. This should resolve your issue.
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4132&lc=en&cc=us&dlc=en&sw_lang=&product=5076...
Hi nosweat
I checked online for the drivers for the Scanjet G4050 on Maverick. None available at this time.
When you connect the device to the computer it should do automatic updates. If not run the apple updates.
Here is a document you can try to see if you can scan using the apple preinstalled drivers.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c03967506#N229
Here is a url to sign up for HP driver updates.
https://h41183.www4.hp.com/signup_alerts.php?country=us&language=en&jumpid=hpalerts_main
Hope this helps.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Hi Team, I wuold like to know if you have any app to make Firefox OS working with cisco Call Manager 10.5. Something like Cisco Jabber for Android or iOS.

I'm interesting on buying a Firefox Smart Phone, but
I would like to know if are any app to install on Firefox OS smart phone in order to work with cisco call manager 10.5.
Something like Cisco Jabber for Android o iOS.
Thanks,

Hi Itech,
If Cisco Jabber has a webapp, or mobile version of their website available, you should technically be able to access it through Firefox OS.
You may also search Firefox Marketplace for an alternative solution:
* [https://marketplace.firefox.com/]
- Ralph

Cisco Jabber for Mac - Directory Lookup and Contact Fields

Hello,
After having issues myself with Cisco Jabber for Mac 9.2 specifically with Active Directory lookups not working, or contact information not populating (and therefore not being able to call users from the contact list as no telephone information exists) I am including a sample jabber-config.xml file that works for me.
Please note: there are many different ways to configure this. What I will be showing is the method that works for me and my deployment, which is pretty standard.
As always and as a disclaimer, once again, this is what has worked for my deployment scenario. Always keep backups of your configuration files, and always be mindful of anything you have configured already, especially in the jabber-config.xml file.
Background
My deployment is based on CUCM 9, with 1 publisher and 2 subscribers. I also have a CUCM IM & Presence 9.0 server. This assumes that you have already configured your deployment and Jabber is functioning already, albeit with the aforementioned issues.
As for Active Directory, my deployment will be based on Windows 2008 R2 Domain Controllers running in native 2008 mode. For this example, we will be searching directly against one of the DCs with a Global Catalogue role. Please be aware that in large deployments you will have to plan accordingly with regards to lookup traffic from Jabber clients to the DCs.
Also, as of Cisco Jabber for Mac 9, the client no longer can search via the CUCM internal directory (which may be made of local end users, Active Directory synced users, or a mix of both) and this must be done via a LDAP mechanism.
Scenario
In this deployment scenario, Cisco Jabber for Windows is working properly - you can search and add people from Active Directory, and contacts in your contact list have all the appropriate fields populated from Active Directory. However, when trying the same with Jabber for Mac, Jabber for iPhone or Jabber for iPad you notice that you cannot perform a directory lookup, and if you add people directly (for example, [email protected]) the user only has the IM field populated. No telephone, email or additional information is displayed.
Solution
Whereas Cisco Jabber for Windows uses the EDI mechanism (native Windows), whereby when running from a computer that is on the domain (or in the event that you are search for contacts in another Active Directory domain where a domain trust exists) , Jabber for Mac / iPhone / iPad uses the BDI mechanism.
In this case, you will need to provision a jabber-config.xml file that you will upload to your TFTP server (or Publisher) that will be "downloaded" by your Jabber for Mac client and also used by the iPhone and iPad client. You can configure many options in the jabber-config.xml file, but for this example we will place just the information that we need to order for these clients to request and display Active Directory information.
Please note that the configuration may vary depending on your deployment, but at the very least we will be:
- Configuring a DC where we will perform the lookup.
- Configure credentials that will be used to perform the lookup. This will be an Active Directory account that has read rights on the Active Directory domain. Please note that these credentials are saved in plain text in the file, so ensure that the account that you will be using is not privileged.
- Configure the server port that we will be using to perform the lookup.
- Configure the Search Base. This is basically where we want the directory lookup to happen. You can either choose for this lookup to start at the "base" of the domain (and therefore the search will iterate through all the user accounts and and OUs below the root base) or define a specific OU where you want to search.
Caution!
- There is a current limitation with Cisco Jabber for Mac whereby you can only have 1 search base configured. Please keep this in mind if, like me, you have multiple OUs (like an OU for each company in your organization) and under these OUs you have sub OUs as a user account container.
- If using the top level search base, unless you specify a filter, you will potentially be able to search for all user accounts in the domain. You will need to configure the <BDIBaseFilter> parameter if you want to fine tune your search ability.
Steps
These are the steps I have followed. Other steps or considerations may vary.
- Log in to your TFTP server and download the jabber-config.xml file and keep it as a backup. If you are already using the jabber-config.xml file for other purposes, do not worry - you can add your BDI information parameters inside.
- Remove the jabber-config.xml file
- Edit the jabber-config.xml file and configure thus:
<?xml version="1.0" encoding="UTF-8"?>
<config version="1.0">
    <Directory>
        <DirectoryServerType>BDI</DirectoryServerType>
        <BDILDAPServerType>AD</BDILDAPServerType>
        <BDIPrimaryServerName>DOMAIN CONTROLLER IP ADDRESS</BDIPrimaryServerName>
        <BDIPresenceDomain>YOUR PRESENCE DOMAIN</BDIPresenceDomain>
        <BDIServerPort1>3268</BDIServerPort1>
        <BDISearchBase1>YOUR SEARCH BASE</BDISearchBase1>
       <BDIConnectionUsername>[email protected]</BDIConnectionUsername>
        <BDIConnectionPassword>PASSWORD</BDIConnectionPassword>
        <BDIEnableTLS>0</BDIEnableTLS>
   </Directory>
</config>
For example, let´s assume the following:
- Domain controller IP address is 10.1.1.2 .
- Your presence domain is test.local .
- Your search base will be test.local using the top level of the domain.
- Your username with which you will be doing your searches is called walt . Usually you can either identify walt as test.local\walt or [email protected] . It is always best, in these sort of scenarios, to use the UPN convention so we will be configuring a [email protected] .
- The password is the Active Directory password for the account walt .
- I have disabled TLS in my case. There are issues with the Jabber for Mac client when using other security methods.
<?xml version="1.0" encoding="UTF-8"?>
<config version="1.0">
    <Directory>
        <DirectoryServerType>BDI</DirectoryServerType>
        <BDILDAPServerType>AD</BDILDAPServerType>
        <BDIPrimaryServerName>10.1.1.2</BDIPrimaryServerName>
        <BDIPresenceDomain>test.local</BDIPresenceDomain>
        <BDIServerPort1>3268</BDIServerPort1>
        <BDISearchBase1>DC=test,DC=local</BDISearchBase1>
       <BDIConnectionUsername>[email protected]</BDIConnectionUsername>
        <BDIConnectionPassword>walt01!</BDIConnectionPassword>
        <BDIEnableTLS>0</BDIEnableTLS>
   </Directory>
</config>
One you have configured the jabber-config.xml file, you will now need to upload it to you TFTP server. Once uploaded, you will need to restart the Cisco TFTP service. Again, my TFTP server is on my CUCM publisher, so:
- I go to Cisco Unified OS Administration on my Publisher server, TFTP File Management and I upload jabber-config.xml to / directory
- I then go to Cisco Unified Serviceability on my Publisher server, I locate the Cisco TFTP service and I restart the service
Once this is done, you can figure up your Jabber for Mac client. As a test, on your Mac (using Terminal) go to:
/Users/username/Library/Application Support/Cisco/Unified Communications/Jabber/Config
In here you will see several files, but what we want to see is jabber-config.xml . As soon as you start the Jabber for Mac client and log in, the jabber-config.xml file will download from your TFTP server and get saved here. When you see it appear, just type in your terminal window more jabber-config.xml and make sure that the output is the same as the xml file you created.
From there, try doing directory search. If you have previously added contacts and they still lack attribute information, you will need to remove them (sometimes it will not refresh properly) and add them again from the directory.
I will be updating this guide and ammending anything that is incorrect, but this is meant to be a quick checklist and steps to get this, at least in the most very basic version, up and running for Jabber for Mac.

Hello,
Thanks for this post! It works, I can do lookup and also I can add found contact to contact list and get information about contact from LDAP.
One more question: - I can't get all information about contact. I don't get e.c mobile phone number and more others attributes. I have tried to expand your file as follows:
<?xml version="1.0" encoding="UTF-8"?>
<config version="1.0">
<Directory>
<DirectoryServerType>BDI</DirectoryServerType>
<BDILDAPServerType>AD</BDILDAPServerType>
<BDIPrimaryServerName>IP of AD</BDIPrimaryServerName>
<BDIPresenceDomain>Presence Domain</BDIPresenceDomain>
<BDIServerPort1>3268</BDIServerPort1>
<BDISearchBase1> Search Base</BDISearchBase1>
<BDIConnectionUsername>User</BDIConnectionUsername>
<BDIConnectionPassword>Password</BDIConnectionPassword>
<BDIEnableTLS>0</BDIEnableTLS>
       <BDISipUri>msRTCSIP-PrimaryUserAddress</BDISipUri>
       <BDIPhotoSource>thumbnailPhoto</BDIPhotoSource>
       <BDIBusinessPhone>telephoneNumber</BDIBusinessPhone>
       <BDIMobilePhone>mobile</BDIMobilePhone>
       <BDIHomePhone>homePhone</BDIHomePhone>
       <BDIOtherPhone>otherTelephone</BDIOtherPhone>
       <BDITitle>title</BDITitle>
       <BDICompanyName>company</BDICompanyName>
<BDILocation>co</BDILocation>
<BDIPostalCode>postalCode</BDIPostalCode>
       <BDICity>l</BDICity>
       <BDIState>st</BDIState>
       <BDIStreetAddress>streetAddress</BDIStreetAddress>
</Directory>
</config>
But it didn't help.
When I capture lookup via Wireshark, I can see that Jabbers sends search request with bunch of attributes, but from LDAP answer contains only 8 attributes. (see attached screenshots)

Cisco Jabber for Windows Voicemail issue

At this I'm in processing of implementation Cisco Jabber UC solution for big Company.
I use CUCM 9.1.2, Cisco IM and Presence 9.1.2, CUC 9.1.2, Cisco Jabber for Windows 9.6.1.
I have issue in Cisco Jabber with VoiceMail Integration - when I leave voice message for any user,
than this message is arrived only him Cisco IP Phone, but not in him Cisco Jabber.
From Cisco Jabber Connectivity status in help menu I see that VoiceMail service is successfully connected
and I see VoiceMail button in Cisco Jabber.
How can I resolve this issue?

Have you configured the UC Service profile on CUCM with both Voicemail server and mailbox servers?

Call/video not working between Cisco jabber for Windows and VCS control C40s

Hello,
I've been struggling with no luck how to make a call using Cisco Jabber for Windows 9.6.0 registered to CM 8.6.2 with intercluster ICT to another CM 8.6.2 where we have a VCS Control 7.0.2 via GK H225, and all C40s are registered as H.323.
The VCS has interworking between H323 and SIP, however not sure if there is any problem with that. Assuming it is ok, not sure either if I'm facing any interoperability issue because in my remote site I have C40 (H323 registered at VCS and SIP listening mode) and cisco jabber for windows which is SIP based.
If is not possible, would I be able to change my C40 from H323 to SIP at VCS, or have both H323/SIP registered at VCS? If so, will I need to change as well instead of GK I'll have to establish a SIP Trunk between the CM and VCS?
Another thing I do not believe either I would be able to have one VCS connected with two clusters, right?
I'm just trying to find a solution in case my current topology is not compatible, but feel free if you have any better idea to make it work.
Anyway here is what is happening:
When I make a call from my cisco jabber windows to C40 using alias number. The call is being redirected just fine to the C40 and it rings, however when someoene or the auto answer picks it up, the call dropped right away.
However, if I enabled the MTP in my CSF device, the call gets longer before dropping. I was even able to see my jabber " start video" turns green, before was grayed out all the time and the call dropped faster. I hear a fast busy tone.
I'm able to provide SDI traces, logs, diagnostic sip/h323 calls from VCS in order to know for sure if this is an incompatible issue or something I can workaround.
Let me know if someone of you are interested in read these logs or could point me on the right direction.
Thanks!

Ok,
I have looked at both logs. I have to mentinon though that you didnt
provide the log that shows the h323 setup between cucm and the VCS. This
is most likely because the call originated from a different cucm than
the ones you provided the logs from.
The call would have orginated from the first cucm in the cucm group of
this trunk: Name=RL_TRUNK_VIDEO
The cucm ip will be : 10.252.53.10.
This is the VCS log that confirms where the h323 request originated
from:
pr 10 22:50:29 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:29,187"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="54000"
Received RAS PDU:
Having said that here is my analysis of the logs that you sent..
Jabber sent an INVITE to CUCM and advertised all the codecs (audio and
video it can support)..
Observer that Jabber says it doesnt support G729 anexB
21:55:16.576 |//SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message
from 10.223.20.73 on port 54677 index 90661 with 2220 bytes:
[862370,NET]
INVITE sip:[email protected];user=phone SIP/2.0
Via: SIP/2.0/TCP 10.223.20.73:54677;branch=z9hG4bK000029d3
From: "4122107" <sip:[email protected]>;tag=00059a3c78000011000070b0
-00000e65
To: <sip:[email protected]>
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 11 Apr 2014 01:55:16 GMT
CSeq: 101 INVITE
User-Agent: Cisco-CSF/9.4.1
m=audio 19252 RTP/AVP 0 8 18 105 104 101
c=IN IP4 10.223.20.73
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=no
a=rtpmap:105 G7221/16000
a=fmtp:105 bitrate=24000
a=rtpmap:104 G7221/16000
a=fmtp:104 bitrate=32000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv
m=video 28878 RTP/AVP 97
c=IN IP4 10.223.20.73
++++Now lets observer the capabilites exchange during h245 negotiation
between cucm and VCS++++
Here CUCM advertises its caps to VCS (afterreceiving caps from VCS)
Note that G729A, G729AB, G729 is all advertised..
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,017"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : terminalCapabilitySet
capabilityTableEntryNumber 2,
       capability receiveAudioCapability :
g729wAnnexB : 6
       capabilityTableEntryNumber 3,
   capability receiveAudioCapability : g729AnnexAwAnnexB : 6
       capabilityTableEntryNumber 4,
       capability
receiveAudioCapability : g729 : 6
capabilityTableEntryNumber 5,
       capability receiveAudioCapability :
g729AnnexA : 6
++++++
After doing MSD (master slave determination, we move to the OLC phas e..
Here we see that the far end..c40 wants to use G729AB for media++++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,783"
Module="network.h323" Level="DEBUG": Src-ip="10.224.114.11" Src-
port="11163"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
+++Next VCS sends G729AB as the codec to use to CUCM+++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,784"
Module="network.h323" Level="DEBUG": Dst-ip="10.252.53.10" Dst-
port="45660"
Sending H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
++++The next thing we get is an OLC reject from CUCM and this is where
th call drops++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= response : openLogicalChannelReject :
forwardLogicalChannelNumber 1,
   cause dataTypeNotSupported : NULL
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="INFO": Dst-ip="10.224.114.11" Dst-
port="11163"
Detail="Sending H.245 OpenLogicalChannelRejResponse
+++We then receive a call release from cucm with cause code of 47:
resource unavailable++++
Apr 10 22:50:32 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:32,365"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="50913"
Received H.225 PDU:
Q931
   Message Type: Release
Complete
   Call reference flag: Message sent from originating side
Call reference value: 0x7b
   Info Element : Cause
     Location: Usr
   Cause Value: Resource unavailable
   Info Element : User User
   Length = 22
Suggestions:
Change the region setting between the ICT trunk to VCS and Jabber to use
G711 and test again.

Cisco Jabber for Blackberry

Hi Jabber Experts,
I was trying with Cisco Jabber IM for Blackberry(9700) , i had manually loaded the application on the device and chose the CUPS(On-Premise) mode installation. I was able succesfully login with my CUPC login credentials. I could see all my contacts, presence info and chat. But Iam not able to place a call. I tried to search one of the contact profile and see no information there, though my desktop(cupc) application all the contact profiles populated with required informations(work phone, cell,email)
We have a LDAP integration on CUPS.
Please advice how can i place a call from my Cisco Jabber Application?
Regards
John

Hi Binu,
Cisco Jabber for Blackberry probably has similar causes for failure to register as the Android version. You may wish to check out the "Cisco Jabber Registration Fails" section at the following URL for ideas:
http://www.cisco.com/en/US/docs/voice_ip_comm/cumc/cisco_jabber/Android/86/Cisco_Jabber_Android_8.6.x_Admin_Guide.html#wp170272
Kind regards,
Craig

Cisco jabber for mac over fortigate vpn problem

Hi all,
We have installed the cisco jabber for mac successfully.Jabber client able to register locally successfully.
Calling and other features working properly. Jabber IM also working fine.
But when we try over vpn its shows error."services are missing".All the ports are open on fortigate firewall.

If you have detailed diagnostics from the Jabber Mac client, this would provide some more context to why it's displaying those errors. (Help > Detailed Logging enabled) (Help > Report a problem)
Another thing to check for would be DNS resolution of the configured servers when the Mac is VPN'd in. If Jabber cannot resolve the DNS name, it will not know where to connect to.
If the diagnostics are pointing towards a connectivity problem, but the firewall says it's wide open, then taking a packet capture on the Mac where Jabber is trying to register may illustrate what's going on at the network layer.

Cisco Jabber for Windows 10.5 search Contact with two lastnames

Hey Guys,
I have a little problem with the contact search feature of the cisco jabber for windows (Version 10.5.37889)
In my environment I have some Users (secretary phones and users too) which have two lastnames.
Exampleuser1: Firstname: Thomas Lastname: Meier Cisco ....
If a user is searching for Exampleuser1 by lastname (Cisco) the correct contact won't be listed
If a user is searching for Exampleuser1 by firstname (Thomas) the correct contact will be listed
If a user is searching for Exampleuser1 by lastname (Meier) the correct contact will be listed
is there a workaround or something else for resolving my problem?
thanks for reading my question :)

Workaround: "Cisco Meier, Thomas"
Have you looked at enabling wild card searches in jabber-config.xml?

Cisco Jabber for Windows - Anti-Virus Software

Hello,
Cisco Jabber for Windows could not resolve outlook contacts, when a client has installed McAffee Anti-Virus Software.
Is there any documentation available, how to setup a Anti-Virus Software, to get Cisco Jabber for Windows running?
Cisco Jabber for Windows Version 9.2.4 Build 4528
Outlook 2013
Thanks
Alex

this is all what we mention about antivirus; http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/jabber/Windows/9_2/JABW_BK_J6915A59_00_jabber-windows-server-setup/JABW_BK_J6915A59_00_jabber-windows-server-setup_chapter_00.html
Some antivirus or firewall applications, such as Symantec EndPoint Protection, block inbound CDP packets, which disables desk phone video capabilities. You should configure your antivirus or firewall application to allow inbound CDP packets. See the following Symantec technical document for additional details about this issue: Cisco IP Phone version 7970 and Cisco Unified Video Advantage is Blocked by Network Threat Protection.
with that being said; we probably would like to get the jabber process excluded from the antivirus list so that it allows for inbound MAPI communication as that is what is used for quering for the outlook contact.
The only process that ever runs from Jabber for windows is "CiscoJabber.exe" which is located in the following path:
C:\Program Files (x86)\Cisco Systems\Cisco Jabber
i hope this helps.

Cisco jabber for android no ask outgoing call

Is available:
1) cucm 8.6
2) The samsung galaxy S4 mini smartphone (android 4.2.2) with the client of cisco jabber for android v 9.1.4
On the smartphone, in the cisco jabber settings, it is specified - to ask for each outgoing call through what to ring.
If to open the address directory of phone and to click a call, the call is made through SIM a card.
How to set up, what the request through what to make an outgoing call would be output?

Take in mind the supported list of devices, in my experience it can be troublesome if you want to uses some of the brands not listed (I played with a Huawei and a LG without luck)
Check http://www.cisco.com/c/en/us/products/collateral/unified-communications/jabber-android/data_sheet_c78-649887.html (Device and OS Requirements)
Regards.
Rolando Valenzuela.

Cisco Jabber for Telepresence 4.6.3 Setting for "Webex Telepresence" Cloud Service

I am looking for the server setting that can be installed into the Cisco Jabber for Telepresence Client (MOVI) that will allow it to connect to the "Webex Telepresence" cloud service. I cannot find a download anywhere that has the infomation re-configured for the "Webex Telepresence" service.
Thanks for your help in advance
Tim
Well after a few hours of searching i have the Answer
The Client can be downloaded from: http://download.telepresence.webex.com/MCX/4.6.3.17194/WIN/JabberVideo_4.6.3GA.exe
This will come with the following setting pre-configured: Sign-in Setting > Internal Server: https://boot.telepresence.webex.com/tmsagent/api/rest/devices/movi/provisioning
If you have the JabberVideo Client installed and just want to change where it gets provisioned from VCS or Webex Telepresence then you should be able to use your current client and just change the internal server settings and clear the external setting.
Then you will need to use your Webex Telepresence Login ID and Password.
Hope this helps Someone.
Tim
Message was edited by: Timothy Shire

A1: Because it can use either (webex or CUPS), there are two deployment modes, all is on the documentation if you haven't gone thru it.
You type in what it's asking, nothing more. Choose one, and then use the CUPS hostname, DNS is basically mandatory, the PC needs name resolution for all you have configured (VM/CUCM/etc)
A2: No, it can be IM&P, full UC and phone mode. No, Full UC and phone mode use the PC for media termination, deskphone control uses the phone for media. Did you change the parameters during install for phone mode??? If not, it's not in phone mode.
A3: No, that can be many things, DNS, connectivity, credentials, etc
You mention DNS is not used, so, most likely that's the problem.
I'd strongly recommend you to review the whole deployment guide for Jabber for Windows.
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

Cisco Jabber for Windows User Photos

CUPS 8.6.3
Jabber Client for Windows Version 9.0.1 Build 8802
I noticed that the Cisco Jabber for Windows Client does not automatically update with the photos that updated in Active Directory.
I had updated a user's photo in AD and noticed that it would not change. I browsed to "C:\Users\<user name>\App Data\Local\Cisco\Unified Communications\Jabber\CSF\Photos" and had to manually delete the user photos in this folder. I exited out of the Jabber Client and restarted the program. When I did this, the Jabber Client crashed, I saved the crash report, and re-opend the Jabber client. This time the client opened properly, and the updated photos were now appearing!
Seems like Cisco would not have set the photos to Cache to the local computer....
Any thoughts?

Yes, Here is a sample .xml script.
<?xml version="1.0" encoding="utf-8"?>
http://www.cisco.com/CiscoJabberSetup.msi
          Cisco
          http://www.cisco.com/web/fw/i/logo-open-graph.gif
          http://www.cisco.com
          Cisco Jabber for Windows
          http://server_name.cisco.com/jabber.png
          http://www.cisco.com/en/US/customer/products/ps12511/tsd_products_support_series_home.html
          Cisco Jabber
          http://server_name.cisco.com/jabber.png
          http://www.cisco.com/web/products/voice/jabber.html
EDI
1
YOURDOMAINCONTROLLER
389
0
ldapaccount
ldapaccountpassword
dc=XXXXXXX,dc=XXXXXXX,dc=com
ipPhone
True
sAMAccountName
http://www.yourinternalwebserver.com/User%20Photos/Profile%20Pictures/sAMAccountName.jpg
true
true
.exe;.msi;.rar;.zip;.mp3
false
presence
The bold is how we pulled photos from a directory on a web server
If you don't have IIS running on a server you can replace
http://www.yourinternalwebserver.com/User%20Photos/Profile%20Pictures/sAMAccountName.jpg
with
\\Your server\c$\PhotoFolder\sAMAccountName.jpg

Configurar smtp en cisco RV110W for scan spiceworks

Similar Messages

Maybe you are looking for