Configuration Assistant Problems

I have installed Solaris 8 on my Intel box and it sits there quite happily. EXCEPT whenever it reboots, I need to reconfigure the incorrectly recognised IDE controller. Does anyone have any ideas on how to 'force' the config assistant to accept a particular configuration without prompting every time?
Thanks in advance,
Ian.

Hi Allen...
I have a similar problem with Solaris 7. I changed my motherboard (gasp!!) and now, when I boot from the hard drive, the Config Assistant is always launched, and it erroneously recognizes the IDE PCI as an ISA PCI device. It will not successfully boot after that.
I do have a workaround though: if I use my backup Config Assistant floppy to boot up, it properly recognizes the IDE PCI, and the boot up successfully completes!! I do not appear to get any errors during the device scan sequence. One more note: I did cause a disk problem during the conversion, but it appeared to be fixed successfully by FSCK. That only happened once. I had had NO problems prior to the motherboard swap with the IDE device suite on my system. My CPU is the AMD K6-2 400Mhz. Any ideas?
Angel Luna

Similar Messages

9i Net Configuration Assistant problem

Hello
I've installed 10g for Windows (XPSP1 PC) where there were separate installations of 9i client and 9i db. All have different home and seems to work fine.
The problem is that both 9i client and 9i db Net Configuration Assistant do not work.
Following the shortcut I reached the file ..\network\tools\netca.cl and inside I found %ORACLE_OEM_CLASSPATH% which does not exists in system variables.
Any comments? 10x
I

now I planning to install 10 g , what do you suggest
to avoid this problem?I suggest you install on [unknown] operating system according to the setup instructions. If you are experiencing netca hangs, it is usually an indication that the installation was incorrect, and often that can be traced to failing to meet the prerequisites.

The Infamous Portal Configuration Assistant Problem

Hi.
Just discovered this forum so I thought I would post up the most common and infuriating problem I have had in the installation of Portal over the past few weeks.....
When attempting to configure Oracle Portal through the Assistant, it asks for the password of SYS which never works, you attempt to connect via SQL*PLUS only to discover the message :
ORA-28009: connection to sys should be as sysdba or sysoper
I'm sure you know what I am talking about so I will leave this there, anybody who has come accross this, fixed this, still fixing it, please post the messages tot his thread regardless of version and platform. That way we will have the ultimate source to the solution of this problem.
I look forward to the posts.
A.M

additional comment:
don't forget to remove or rename the associated spfile.
(usually located in the C:\oracle\admin directory for example.)
Otherwise Oracle will never read the specific init<SID>.ora file.
regards,
Udo

Net8 Configuration Assistant Problem?

NCA installed on Win98 is ok with Oracle8.1.6 EE R2 on Win2000.
But, NCA don't work with Oracle8.1.6 EE on Red Hat Linux 6.2.
Followed are .ora files.
Server(Linux):
$ORACLE_HOME/network/admin/listener.ora
LISTENER =
(ADDRESS_LIST =
(ADDRESS =
(PROTOCOL = TCP)
(HOST = xx.xx.xx.xx)
(PORT = 1521))
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(GLOBAL_DBNAME = HHH.AAA.BBB.com)
(ORACLE_HOME = /home/oracle/oracle8i)
(SID_NAME = ora8i)
$ORACLE_HOME/network/admin/tnsnames.ora
HHH.AAA.BBB.COM =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS =
(PROTOCOL = TCP)
(HOST = xx.xx.xx.xx)
(PORT = 1521)
(CONNECT_DATA =
(SERVICE_NAME = hhh.aaa.bbb.com)
Client(Windows 98)
/oracle/oracle8i/network/admin/tnsnames.ora
# TNSNAMES.ORA Network Configuration File: d:\Oracle\Oracle8i\network\admin\tnsnames.ora
# Generated by Oracle configuration tools.
HHH.AAA.BBB.COM =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS =
(PROTOCOL = TCP)
(HOST = xx.xx.xx.xx)
(PORT = 1521)
(CONNECT_DATA =
(SERVICE_NAME = hhh.aaa.bbb.com)
null

u are very lucky .i installed oracle context and make ldap as the first naming method ,but i cannot get the 'test'&'test with sql*plus' menu item from windows Explorer.and the oracleContext icon is not fulled.i think i did not make active directory fit for oracle ,but can u tell me why.
thank u .

8.1.5 Install Problem: Database Configuration Assistant

I have problems installing Oracle 8.1.5 on Linux.
On the "Configuration tools" screen, I get the following
error for the 'Oracle Database Configuration Assistant':
"A required command line argument is missing"
The installation claims the error is not critical.
When I try to access the database with SQL*Plus and the default
SYS/CHANGE_ME_ON_INSTALL login, I get the following error:
ORA01033: Oracle intialization or shutdown in progress.
I cannot start or stop the database.
When I use "connect internal" in srvmgr, and try to do "startup",
I get "insufficient privileges".
When I use "connect SYSTEM/CHANGE_ME_ON_INSTALL", I get ORA01033
again.
My system configuration:
RedHat 6.0
2x Pentium II 266
192 MB RAM
Java JRE 1.6.5
Kernel 2.2.10
Hints etc. appreciated.
null

I have exactly the same setup (ie 2.2.10 etc) with
exactly the same error message on install. In fact
as far as I can tell no database was created because
of this error. I run the "dbassist" sepeartely after the
install and I get :
" JNLS Excetion:oracle.....
Unable to find any National Character Sets.
Please Check your Oracle Installation"
This is a stock redhat 6.0 install with the addition
of the redhat errata updates(ie enlightenment-0.15.5-36
, X, kde etc) and kernel 2.2.10.
Yes logged in as the "oracle" user which also has group
dba priv.
Michael (guest) wrote:
: The default password for sys is change_on_install, not
: change_me_on_install, although a regular "connect internal"
: should still work regardless (it won't for future versions, but
: in 8.1.5, it should still work at least). Are you logged into
: the OS as the "oracle" account (or whatever you used as the
: install account)? Is this user a member of the "dba" group?
: Also, make sure the permissions/ownerships of the files are
: correct--your umask should have been 022 on the install account
: before the install. The install manual states the correct
: permissions on important files, and ownerships should pretty
much
: all (if not all) be oracle:dba.
: If a shutdown was initiated, was it long ago? Live Oracle dbs
: can take a while to shutdown, but if this is a new install and
: not live or anything, it shouldn't take that long.
: Sven Neuhaus (guest) wrote:
: : I have problems installing Oracle 8.1.5 on Linux.
: : On the "Configuration tools" screen, I get the following
: : error for the 'Oracle Database Configuration Assistant':
: : "A required command line argument is missing"
: : The installation claims the error is not critical.
: : When I try to access the database with SQL*Plus and the
default
: : SYS/CHANGE_ME_ON_INSTALL login, I get the following error:
: : ORA01033: Oracle intialization or shutdown in progress.
: : I cannot start or stop the database.
: : When I use "connect internal" in srvmgr, and try to do
: "startup",
: : I get "insufficient privileges".
: : When I use "connect SYSTEM/CHANGE_ME_ON_INSTALL", I get
: ORA01033
: : again.
: : My system configuration:
: : RedHat 6.0
: : 2x Pentium II 266
: : 192 MB RAM
: : Java JRE 1.6.5
: : Kernel 2.2.10
: : Hints etc. appreciated.
null

Security problem in oracle 9i Database Configuration Assistant

Inside the tool Oracle 9i Database Configuration Assistant there is an option by which you can make a "copy" of your Database. This "copy" is called a template and you don4t need any password or aunthentication to do it, you just need the tool to be installed in your server. Once you have a template, you can bring it anywhere and recreate the original database (including data). Again, you don't need any password or aunthentication to do it, further more, in the last step of this process you can change the password of any user (inluding SYS, SYSTEM or another DBA user). The thing about this is that anyone with access to the computer where the database is can make a template of it, take this template to another computer and recreate my database having FULL access to it (structure, data, code ...). And everything without needing any password!!!. I really thing that it is a big problem. Is there any way of preventing this operation?. How can I safely protect my database?. I thought about unistalling the product, but someone can re-install it and everything would be the same. Can someone give me an answer?
Thanks for everything.
Pablo Cuenca

You must protect your database from casual browsing at the OS level. This is not a security hole, per se, since this is a known issue with any and all software. Database Configuration Assistant is not needed for this since one may copy the database without it.

Database configuration assistant privlege problem

I am installing Oracle 9i R2 (9.2.4) install on Redhat 7.3.
I am following the guides at:
http://www.puschitz.com/InstallingOracle9i.shtml
I launched the oracle runInstaller, I can go through to the point where I choose Database configuration which I select(Software only) and click next.
It failes with the following error dialog:
Error: You do not have sufficient privileges to write to the specified path. in compnonent Database Configuration Assistant 9.2.0.1.0. Installation cannot continue for this component.
O Stop installation of all products
O Stop installation of this component only
OK
I continue the installation. Many things are installed, but at the end of the installation, it s written "Oracle installation Failed".
Does anyone know where my permissions problem is and the way to complete the install succesfully?
(how can I create the my first database, sqlplus seems not installed )
Thank you.
Edouard.

The problem could arise not having set ORACLE_BASE environment variable : in this case the Installer could try creating directories under root (/).
But there is Bug No. 3547724 as well : NEW 9.2.0.4 FOR LINUX 'REKIT' FAILS TO INSTALL DBCA - INSUFFICIENT PRIVILEGES. In this case the suggested workaround is to install 9.2.0.1, then patch 9.2.0.4 .

Problem during installation oracle database configuration assistant FAILED

Hi Dear,
The Configurations are :
VM OS : Oracle enterprise linux 5
Trying to install : Oracle 11g R1
I'm having a real problem , so i can't continue my installation during the configuration assistant, oracle net configuration assistant was succeeded but oracle database configuration assistant FAILED
Here is the long message showed by console :
Output generated from configuration assistant "Oracle Net Configuration Assistant":
Command = /u01/app/oracle/product/11.1.0/db_1/bin/netca /orahome /u01/app/oracle/product/11.1.0/db_1 /orahnam OraDb11g_home1 /instype typical /inscomp client,oraclenet,javavm,server,ano /insprtcl tcp /cfg local /authadp NO_VALUE /nodeinfo NO_VALUE /responseFile /u01/app/oracle/product/11.1.0/db_1/network/install/netca_typ.rsp
Parsing command line arguments:
Parameter "orahome" = /u01/app/oracle/product/11.1.0/db_1
Parameter "orahnam" = OraDb11g_home1
Parameter "instype" = typical
Parameter "inscomp" = client,oraclenet,javavm,server,ano
Parameter "insprtcl" = tcp
Parameter "cfg" = local
Parameter "authadp" = NO_VALUE
Parameter "nodeinfo" = NO_VALUE
Parameter "responsefile" = /u01/app/oracle/product/11.1.0/db_1/network/install/netca_typ.rsp
Done parsing command line arguments.
Oracle Net Services Configuration:
Profile configuration complete.
Listener started at port:1521
Oracle Net Listener Startup:
Running Listener Control:
/u01/app/oracle/product/11.1.0/db_1/bin/lsnrctl start LISTENER
Listener Control complete.
Listener started successfully.
Listener configuration complete.
Oracle Net Services configuration successful. The exit code is 0
Configuration assistant "Oracle Net Configuration Assistant" succeeded
Output generated from configuration assistant "Oracle Database Configuration Assistant":
Command = oracle.assistants.server.DbcaCfgPlugIn /u01/app/oracle/product/11.1.0/db_1/bin/dbca -progress_only -createDatabase -templateName General_Purpose.dbc -sid DB11G -gdbName DB11G.WORLD -emConfiguration LOCAL -datafileJarLocation /u01/app/oracle/product/11.1.0/db_1/assistants/dbca/templates -datafileDestination /u01/app/oracle/oradata/ -responseFile NO_VALUE -characterset WE8MSWIN1252 -obfuscatedPasswords false -sampleSchema false -oratabLocation /u01/app/oracle/product/11.1.0/db_1/install/oratab -recoveryAreaDestination NO_VALUE -totalMemory 403 -automaticMemoryManagement true -sysPassword ${S_SYSPASS} -systemPassword ${S_SYSTEMPASS} -dbsnmpPassword ${S_DBSNMPPASS} -sysmanPassword ${S_SYSMANPASS} ${S_SYSASMPASS} ${S_HOSTUSERPASS}
Configuration assistant "Oracle Database Configuration Assistant" failed
The "/u01/app/oracle/product/11.1.0/db_1/cfgtoollogs/configToolFailedCommands" script contains all commands that failed, were skipped or were cancelled. This file may be used to run these configuration assistants outside of OUI. Note that you may have to update this script with passwords (if any) before executing the same.-----------------------------------------------------------------------------Output generated from configuration assistant "Oracle Database Configuration Assistant":
Command = oracle.assistants.server.DbcaCfgPlugIn /u01/app/oracle/product/11.1.0/db_1/bin/dbca -progress_only -createDatabase -templateName General_Purpose.dbc -sid DB11G -gdbName DB11G.WORLD -emConfiguration LOCAL -datafileJarLocation /u01/app/oracle/product/11.1.0/db_1/assistants/dbca/templates -datafileDestination /u01/app/oracle/oradata/ -responseFile NO_VALUE -characterset WE8MSWIN1252 -obfuscatedPasswords false -sampleSchema false -oratabLocation /u01/app/oracle/product/11.1.0/db_1/install/oratab -recoveryAreaDestination NO_VALUE -totalMemory 403 -automaticMemoryManagement true -sysPassword ${S_SYSPASS} -systemPassword ${S_SYSTEMPASS} -dbsnmpPassword ${S_DBSNMPPASS} -sysmanPassword ${S_SYSMANPASS} ${S_SYSASMPASS} ${S_HOSTUSERPASS}
Configuration assistant "Oracle Database Configuration Assistant" failed
The "/u01/app/oracle/product/11.1.0/db_1/cfgtoollogs/configToolFailedCommands" script contains all commands that failed, were skipped or were cancelled. This file may be used to run these configuration assistants outside of OUI. Note that you may have to update this script with passwords (if any) before executing the same.-----------------------------------------------------------------------------Output generated from configuration assistant "Oracle Database Configuration Assistant" (attempt 2):
Command = oracle.assistants.server.DbcaCfgPlugIn /u01/app/oracle/product/11.1.0/db_1/bin/dbca -progress_only -createDatabase -templateName General_Purpose.dbc -sid DB11G -gdbName DB11G.WORLD -emConfiguration LOCAL -datafileJarLocation /u01/app/oracle/product/11.1.0/db_1/assistants/dbca/templates -datafileDestination /u01/app/oracle/oradata/ -responseFile NO_VALUE -characterset WE8MSWIN1252 -obfuscatedPasswords false -sampleSchema false -oratabLocation /u01/app/oracle/product/11.1.0/db_1/install/oratab -recoveryAreaDestination NO_VALUE -totalMemory 403 -automaticMemoryManagement true -sysPassword ${S_SYSPASS} -systemPassword ${S_SYSTEMPASS} -dbsnmpPassword ${S_DBSNMPPASS} -sysmanPassword ${S_SYSMANPASS} ${S_SYSASMPASS} ${S_HOSTUSERPASS}
Configuration assistant "Oracle Database Configuration Assistant" failed
The "/u01/app/oracle/product/11.1.0/db_1/cfgtoollogs/configToolFailedCommands" script contains all commands that failed, were skipped or were cancelled. This file may be used to run these configuration assistants outside of OUI. Note that you may have to update this script with passwords (if any) before executing the same.-----------------------------------------------------------------------------Output generated from configuration assistant "Oracle Database Configuration Assistant" (attempt 3):
Command = oracle.assistants.server.DbcaCfgPlugIn /u01/app/oracle/product/11.1.0/db_1/bin/dbca -progress_only -createDatabase -templateName General_Purpose.dbc -sid DB11G -gdbName DB11G.WORLD -emConfiguration LOCAL -datafileJarLocation /u01/app/oracle/product/11.1.0/db_1/assistants/dbca/templates -datafileDestination /u01/app/oracle/oradata/ -responseFile NO_VALUE -characterset WE8MSWIN1252 -obfuscatedPasswords false -sampleSchema false -oratabLocation /u01/app/oracle/product/11.1.0/db_1/install/oratab -recoveryAreaDestination NO_VALUE -totalMemory 403 -automaticMemoryManagement true -sysPassword ${S_SYSPASS} -systemPassword ${S_SYSTEMPASS} -dbsnmpPassword ${S_DBSNMPPASS} -sysmanPassword ${S_SYSMANPASS} ${S_SYSASMPASS} ${S_HOSTUSERPASS}
Configuration assistant "Oracle Database Configuration Assistant" failed
The "/u01/app/oracle/product/11.1.0/db_1/cfgtoollogs/configToolFailedCommands" script contains all commands that failed, were skipped or were cancelled. This file may be used to run these configuration assistants outside of OUI. Note that you may have to update this script with passwords (if any) before executing the same.-----------------------------------------------------------------------------
Please help me it's urgently

Please help me i can't find any solution to resolve this trouble
Should i uninstall this version or what exactly, could you please suggest to me something like another release who matches that configuration
Sorry but i have no idea
Waiting for the response

Problem using template in database configuration assistant Oracle 10g

Hi,
I created a database using the database configuration assistant for Oracle 10g on a Windows Server 2003 box. The database I created worked perfectly, and I had saved it as a template so I could save some time when creating similar databases (which I have to do on occasion)
When I try to use the template though, I get an error (at about 4% through the database creation) saying:
ORA-01501: CREATE DATABASE failed
ORA-09314: sltln: error translating logical name
I'm creating this new database on the same server as the one I created my previous database on and NOTHING has changed on it, I did this just minutes apart and can duplicate it at will (just try and use a template)
Heres the template file contents (KM1.dbt)
<DatabaseTemplate name="KM1" description="" version="10.1.0.2.0">
<CommonAttributes>
<option name="ISEARCH" value="false"/>
<option name="OMS" value="false"/>
<option name="JSERVER" value="false"/>
<option name="SPATIAL" value="false"/>
<option name="ODM" value="false">
<tablespace id="SYSAUX"/>
</option>
<option name="IMEDIA" value="false"/>
<option name="XDB_PROTOCOLS" value="false">
<tablespace id="SYSAUX"/>
</option>
<option name="ORACLE_TEXT" value="false">
<tablespace id="SYSAUX"/>
</option>
<option name="SAMPLE_SCHEMA" value="false"/>
<option name="CWMLITE" value="false">
<tablespace id="SYSAUX"/>
</option>
<option name="EM_REPOSITORY" value="true">
<tablespace id="SYSAUX"/>
</option>
</CommonAttributes>
<Variables/>
<CustomScripts Execute="false"/>
<InitParamAttributes>
<InitParams>
<initParam name="O7_DICTIONARY_ACCESSIBILITY" value="TRUE"/>
<initParam name="background_dump_dest" value="{ORACLE_BASE}\admin\{DB_UNIQUE_NAME}\bdump"/>
<initParam name="compatible" value="10.1.0.2.0"/>
<initParam name="core_dump_dest" value="{ORACLE_BASE}\admin\{DB_UNIQUE_NAME}\cdump"/>
<initParam name="db_block_size" value="8" unit="KB"/>
<initParam name="db_cache_size" value="24" unit="MB"/>
<initParam name="db_create_file_dest" value="E:\oradata"/>
<initParam name="db_create_online_log_dest_1" value="C:\Oradata"/>
<initParam name="db_create_online_log_dest_2" value="D:\Oradata"/>
<initParam name="db_create_online_log_dest_3" value="E:\Oradata"/>
<initParam name="db_domain" value="JACOBSONCO.COM"/>
<initParam name="db_file_multiblock_read_count" value="16"/>
<initParam name="db_name" value="UDC7"/>
<initParam name="db_recovery_file_dest" value="E:\UDC7\flash_recovery_area"/>
<initParam name="db_recovery_file_dest_size" value="2048" unit="MB"/>
<initParam name="java_pool_size" value="0" unit="MB"/>
<initParam name="job_queue_processes" value="10"/>
<initParam name="large_pool_size" value="8" unit="MB"/>
<initParam name="open_cursors" value="1000"/>
<initParam name="pga_aggregate_target" value="24" unit="MB"/>
<initParam name="processes" value="150"/>
<initParam name="remote_login_passwordfile" value="EXCLUSIVE"/>
<initParam name="shared_pool_size" value="80" unit="MB"/>
<initParam name="sort_area_size" value="65536"/>
<initParam name="undo_management" value="AUTO"/>
<initParam name="undo_tablespace" value="UNDOTBS1"/>
<initParam name="user_dump_dest" value="{ORACLE_BASE}\admin\{DB_UNIQUE_NAME}\udump"/>
</InitParams>
<MiscParams>
<databaseType>MULTIPURPOSE</databaseType>
<maxUserConn>20</maxUserConn>
<percentageMemTOSGA>40</percentageMemTOSGA>
<customSGA>true</customSGA>
<characterSet>WE8MSWIN1252</characterSet>
<nationalCharacterSet>AL16UTF16</nationalCharacterSet>
<archiveLogMode>false</archiveLogMode>
<initParamFileName>{ORACLE_BASE}\admin\{DB_UNIQUE_NAME}\pfile\init.ora</initParamFileName>
</MiscParams>
<SPfile useSPFile="true">{ORACLE_HOME}\database\spfile{SID}.ora</SPfile>
</InitParamAttributes>
<StorageAttributes>
<ControlfileAttributes id="Controlfile">
<maxDatafiles>100</maxDatafiles>
<maxLogfiles>16</maxLogfiles>
<maxLogMembers>3</maxLogMembers>
<maxLogHistory>1</maxLogHistory>
<maxInstances>8</maxInstances>
<image name="<OMF_CONTROL_0>" filepath="{ORACLE_BASE}\oradata\{DB_UNIQUE_NAME}\"/>
<image name="<OMF_CONTROL_1>" filepath="{ORACLE_BASE}\oradata\{DB_UNIQUE_NAME}\"/>
<image name="<OMF_CONTROL_2>" filepath="{ORACLE_BASE}\oradata\{DB_UNIQUE_NAME}\"/>
</ControlfileAttributes>
<DatafileAttributes id="<OMF_SNIKEB_DATAFILE_0>">
<tablespace>SNIKEB</tablespace>
<temporary>false</temporary>
<online>true</online>
<status>0</status>
<size unit="MB">300</size>
<reuse>false</reuse>
<autoExtend>false</autoExtend>
<increment unit="KB">-2</increment>
<maxSize unit="KB">-1</maxSize>
</DatafileAttributes>
<DatafileAttributes id="<OMF_SYSAUX_DATAFILE_0>">
<tablespace>SYSAUX</tablespace>
<temporary>false</temporary>
<online>true</online>
<status>0</status>
<size unit="MB">120</size>
<reuse>true</reuse>
<autoExtend>true</autoExtend>
<increment unit="KB">10240</increment>
<maxSize unit="MB">-1</maxSize>
</DatafileAttributes>
<DatafileAttributes id="<OMF_SYSTEM_DATAFILE_0>">
<tablespace>SYSTEM</tablespace>
<temporary>false</temporary>
<online>true</online>
<status>0</status>
<size unit="MB">300</size>
<reuse>true</reuse>
<autoExtend>true</autoExtend>
<increment unit="KB">10240</increment>
<maxSize unit="MB">-1</maxSize>
</DatafileAttributes>
<DatafileAttributes id="<OMF_TEMP_DATAFILE_0>">
<tablespace>TEMP</tablespace>
<temporary>false</temporary>
<online>true</online>
<status>0</status>
<size unit="MB">20</size>
<reuse>true</reuse>
<autoExtend>true</autoExtend>
<increment unit="KB">640</increment>
<maxSize unit="MB">-1</maxSize>
</DatafileAttributes>
<DatafileAttributes id="<OMF_UNDOTBS1_DATAFILE_0>">
<tablespace>UNDOTBS1</tablespace>
<temporary>false</temporary>
<online>true</online>
<status>0</status>
<size unit="MB">200</size>
<reuse>true</reuse>
<autoExtend>true</autoExtend>
<increment unit="KB">5120</increment>
<maxSize unit="MB">-1</maxSize>
</DatafileAttributes>
<DatafileAttributes id="<OMF_USERS_DATAFILE_0>">
<tablespace>USER_DATA</tablespace>
<temporary>false</temporary>
<online>true</online>
<status>0</status>
<size unit="MB">5</size>
<reuse>true</reuse>
<autoExtend>true</autoExtend>
<increment unit="KB">1280</increment>
<maxSize unit="MB">-1</maxSize>
</DatafileAttributes>
<TablespaceAttributes id="SNIKEB">
<online>true</online>
<offlineMode>1</offlineMode>
<readOnly>false</readOnly>
<temporary>false</temporary>
<defaultTemp>false</defaultTemp>
<undo>false</undo>
<local>true</local>
<blockSize>-1</blockSize>
<allocation>1</allocation>
<uniAllocSize unit="KB">-1</uniAllocSize>
<initSize unit="KB">-1</initSize>
<increment unit="KB">-1</increment>
<incrementPercent>-1</incrementPercent>
<minExtends>-1</minExtends>
<maxExtends>-2</maxExtends>
<minExtendsSize unit="KB">-1</minExtendsSize>
<logging>true</logging>
<recoverable>false</recoverable>
<maxFreeSpace>0</maxFreeSpace>
<autoSegmentMgmt>true</autoSegmentMgmt>
<datafilesList>
<TablespaceDatafileAttributes id="<OMF_SNIKEB_DATAFILE_0>">
<id>1</id>
</TablespaceDatafileAttributes>
</datafilesList>
</TablespaceAttributes>
<TablespaceAttributes id="SYSAUX">
<online>true</online>
<offlineMode>1</offlineMode>
<readOnly>false</readOnly>
<temporary>false</temporary>
<defaultTemp>false</defaultTemp>
<undo>false</undo>
<local>true</local>
<blockSize>-1</blockSize>
<allocation>1</allocation>
<uniAllocSize unit="KB">-1</uniAllocSize>
<initSize unit="KB">64</initSize>
<increment unit="KB">64</increment>
<incrementPercent>50</incrementPercent>
<minExtends>1</minExtends>
<maxExtends>4096</maxExtends>
<minExtendsSize unit="KB">64</minExtendsSize>
<logging>true</logging>
<recoverable>false</recoverable>
<maxFreeSpace>0</maxFreeSpace>
<autoSegmentMgmt>true</autoSegmentMgmt>
<datafilesList>
<TablespaceDatafileAttributes id="<OMF_SYSAUX_DATAFILE_0>">
<id>-1</id>
</TablespaceDatafileAttributes>
</datafilesList>
</TablespaceAttributes>
<TablespaceAttributes id="SYSTEM">
<online>true</online>
<offlineMode>1</offlineMode>
<readOnly>false</readOnly>
<temporary>false</temporary>
<defaultTemp>false</defaultTemp>
<undo>false</undo>
<local>true</local>
<blockSize>-1</blockSize>
<allocation>3</allocation>
<uniAllocSize unit="KB">-1</uniAllocSize>
<initSize unit="KB">64</initSize>
<increment unit="KB">64</increment>
<incrementPercent>50</incrementPercent>
<minExtends>1</minExtends>
<maxExtends>-1</maxExtends>
<minExtendsSize unit="KB">64</minExtendsSize>
<logging>true</logging>
<recoverable>false</recoverable>
<maxFreeSpace>0</maxFreeSpace>
<autoSegmentMgmt>true</autoSegmentMgmt>
<datafilesList>
<TablespaceDatafileAttributes id="<OMF_SYSTEM_DATAFILE_0>">
<id>-1</id>
</TablespaceDatafileAttributes>
</datafilesList>
</TablespaceAttributes>
<TablespaceAttributes id="TEMP">
<online>true</online>
<offlineMode>1</offlineMode>
<readOnly>false</readOnly>
<temporary>true</temporary>
<defaultTemp>true</defaultTemp>
<undo>false</undo>
<local>true</local>
<blockSize>-1</blockSize>
<allocation>1</allocation>
<uniAllocSize unit="KB">-1</uniAllocSize>
<initSize unit="KB">64</initSize>
<increment unit="KB">64</increment>
<incrementPercent>0</incrementPercent>
<minExtends>1</minExtends>
<maxExtends>0</maxExtends>
<minExtendsSize unit="KB">64</minExtendsSize>
<logging>true</logging>
<recoverable>false</recoverable>
<maxFreeSpace>0</maxFreeSpace>
<autoSegmentMgmt>true</autoSegmentMgmt>
<datafilesList>
<TablespaceDatafileAttributes id="<OMF_TEMP_DATAFILE_0>">
<id>-1</id>
</TablespaceDatafileAttributes>
</datafilesList>
</TablespaceAttributes>
<TablespaceAttributes id="UNDOTBS1">
<online>true</online>
<offlineMode>1</offlineMode>
<readOnly>false</readOnly>
<temporary>false</temporary>
<defaultTemp>false</defaultTemp>
<undo>true</undo>
<local>true</local>
<blockSize>-1</blockSize>
<allocation>1</allocation>
<uniAllocSize unit="KB">-1</uniAllocSize>
<initSize unit="KB">512</initSize>
<increment unit="KB">512</increment>
<incrementPercent>50</incrementPercent>
<minExtends>8</minExtends>
<maxExtends>4096</maxExtends>
<minExtendsSize unit="KB">512</minExtendsSize>
<logging>true</logging>
<recoverable>false</recoverable>
<maxFreeSpace>0</maxFreeSpace>
<autoSegmentMgmt>true</autoSegmentMgmt>
<datafilesList>
<TablespaceDatafileAttributes id="<OMF_UNDOTBS1_DATAFILE_0>">
<id>-1</id>
</TablespaceDatafileAttributes>
</datafilesList>
</TablespaceAttributes>
<TablespaceAttributes id="USER_DATA">
<online>true</online>
<offlineMode>1</offlineMode>
<readOnly>false</readOnly>
<temporary>false</temporary>
<defaultTemp>false</defaultTemp>
<undo>false</undo>
<local>true</local>
<blockSize>-1</blockSize>
<allocation>1</allocation>
<uniAllocSize unit="KB">-1</uniAllocSize>
<initSize unit="KB">128</initSize>
<increment unit="KB">128</increment>
<incrementPercent>0</incrementPercent>
<minExtends>1</minExtends>
<maxExtends>4096</maxExtends>
<minExtendsSize unit="KB">128</minExtendsSize>
<logging>true</logging>
<recoverable>false</recoverable>
<maxFreeSpace>0</maxFreeSpace>
<autoSegmentMgmt>true</autoSegmentMgmt>
<datafilesList>
<TablespaceDatafileAttributes id="<OMF_USERS_DATAFILE_0>">
<id>-1</id>
</TablespaceDatafileAttributes>
</datafilesList>
</TablespaceAttributes>
<RedoLogGroupAttributes id="1">
<reuse>false</reuse>
<fileSize unit="KB">10240</fileSize>
<Thread>1</Thread>
<member ordinal="0" memberName="OMF_1_REDOLOG_MEMBER_0" filepath="{ORACLE_BASE}\oradata\{DB_UNIQUE_NAME}\"/>
</RedoLogGroupAttributes>
<RedoLogGroupAttributes id="2">
<reuse>false</reuse>
<fileSize unit="KB">10240</fileSize>
<Thread>1</Thread>
<member ordinal="0" memberName="OMF_2_REDOLOG_MEMBER_0" filepath="{ORACLE_BASE}\oradata\{DB_UNIQUE_NAME}\"/>
</RedoLogGroupAttributes>
<RedoLogGroupAttributes id="3">
<reuse>false</reuse>
<fileSize unit="KB">10240</fileSize>
<Thread>1</Thread>
<member ordinal="0" memberName="OMF_3_REDOLOG_MEMBER_0" filepath="{ORACLE_BASE}\oradata\{DB_UNIQUE_NAME}\"/>
</RedoLogGroupAttributes>
</StorageAttributes>
</DatabaseTemplate>
can anyone explain why I keep getting this error?
Thanks

Error:     ORA-9314
Text:     sltln: error translating logical name
Cause:     Internal buffer may have overflowed
Action:     See OSD error accompanying this message
Check alertlog and trace files.
Message was edited by:
FeNiCrC_Neil

Problem in net configuration assistant

Hi,I have loaded oracle 9ienterprise edition on one PC and oracle9i client.when i am running Net configuration assistant to connect to server it gives me error ORA-12535: TNS:operation timed out.i have tried lot of things like reinstalling client,dropped and recreated database.infact when i do TNSping from client it does nt show me any database.Please guide me through.i have first created listener and then Local net service configuration.my database name is ORCL and in host name i am giving database pc ip address on client machine.

Hi,thanx for your reply...plz find below the listener.ora file for sever and client
[b]For server
# LISTENER.ORA Network Configuration File: D:\oracle\ora92\network\admin\listener.ora
# Generated by Oracle configuration tools.
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = abc)(PORT = 1521))
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\ora92)
(PROGRAM = extproc)
[b]For client
# LISTENER.ORA Network Configuration File: D:\oracle\ora92\network\admin\listener.ora
# Generated by Oracle configuration tools.
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = abc)(PORT = 1521))
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\ora92)
(PROGRAM = extproc)
)

Installation Problem --- Stuck at "Java Security Configuration Assistant"

When installing Oracle BI 10g, the procedure stuck at "Java Security Configuration Assistant"
Output generated from configuration assistant "Java Security Configuration Assistant":
Invoking command:C:\OraHome_1\dcm\bin\dcmctl.bat resyncInstance
OS: Windows 2003 Ent. (SP1)
Memory: 1G
Does anybody knows the reason? and solve
Thanks,

Hello,
just to keep you inform.
I put that project on the side for a while... But this morning, I tried Branislav recommendation.
So, I completely uninstall my McAffe Firewall and reboot the computer.
After that, I completely re-install the application server and everything work fine. It only took around 2-3 seconds to do the resyncinstance and updateconfig, compare to 3 hours the last time just for the resyncinstance. Total time for the infrastructure installation was around 1 hour.
Like Branislav said, only stopping the McAfee Firewall was not enough.
Thanks

Problems with Database Configuration Assistant - Error in Process

Hello guys,
I'm getting this error when i try to create a new Database with the Database Configuration Assistant:
Error in Process: E:\ORACLE\product\11.2.0\dbhome_1\bin\orapwd.exe
Unable to find error file %ORACLE_HOME%\RDBMS\opw<lang>.msb
What should I do in this case? Any idea?
Thanks

Please re-check the ORACLE_HOME variable and restart the process. This will resolve your issue.

Error installing OBIEE 11g on Linux 64 bits - Configuration Assistant fails

Hello,
I am trying to install OBISE1 on Oracle Linux 5 - 64 bits.
I've followed these steps:
1) Install Oracle DB
2) Install jdk Linux 64 bits (jdk1.7.0)
3) Install WebLogic
4) Install RCU
5) Install OBI 11g (Software only installation)
Until here, all is correct.
6) Configuration assistant failed:
[2011-09-12T12:04:58.844+02:00] [as] [ERROR] [] [oracle.as.provisioning]
[tid: 14] [ecid: 0000J9Soq_rFGBWFLz6UOA1ERSJh000005,0]
[2011-09-12T12:04:58.845+02:00] [as] [ERROR] [] [oracle.as.provisioning]
[tid: 14] [ecid: 0000J9Soq_rFGBWFLz6UOA1ERSJh000005,0] [[
oracle.as.provisioning.util.ConfigException:
Error while starting the domain.
Cause:
Starting the Admin_Server timed out.
Action:
See logs for more details.
at oracle.as.provisioning.util.ConfigException.createConfigException(ConfigException.java:123)
at oracle.as.provisioning.weblogic.ASDomain.startDomain(ASDomain.java:3149)
at oracle.as.provisioning.weblogic.ASDomain.startDomain(ASDomain.java:3039)
at oracle.as.provisioning.engine.WorkFlowExecutor._startAdminServer(WorkFlowExecutor.java:1645)
at oracle.as.provisioning.engine.WorkFlowExecutor._createDomain(WorkFlowExecutor.java:635)
at oracle.as.provisioning.engine.WorkFlowExecutor.executeWLSWorkFlow(WorkFlowExecutor.java:391)
at oracle.as.provisioning.engine.Config.executeConfigWorkflow_WLS(Config.java:866)
at oracle.as.install.bi.biconfig.standard.StandardWorkFlowExecutor.executeHelper(StandardWorkFlowExecutor.java:31)
at oracle.as.install.bi.biconfig.standard.DomainProvisioningTask.doExecute(DomainProvisioningTask.java:48)
at oracle.as.install.bi.biconfig.standard.AbstractProvisioningTask.execute(AbstractProvisioningTask.java:70)
at oracle.as.install.bi.biconfig.standard.StandardProvisionTaskList.execute(StandardProvisionTaskList.java:61)
at oracle.as.install.bi.biconfig.BIConfigMain.doExecute(BIConfigMain.java:112)
at oracle.as.install.engine.modules.configuration.client.ConfigAction.execute(ConfigAction.java:335)
at oracle.as.install.engine.modules.configuration.action.TaskPerformer.run(TaskPerformer.java:87)
at oracle.as.install.engine.modules.configuration.action.TaskPerformer.startConfigAction(TaskPerformer.java:104)
at oracle.as.install.engine.modules.configuration.action.ActionRequest.perform(ActionRequest.java:15)
at oracle.as.install.engine.modules.configuration.action.RequestQueue.perform(RequestQueue.java:63)
at oracle.as.install.engine.modules.configuration.standard.StandardConfigActionManager.start(StandardConfigActionManager.java:158)
at oracle.as.install.engine.modules.configuration.boot.ConfigurationExtension.kickstart(ConfigurationExtension.java:81)
at oracle.as.install.engine.modules.configuration.ConfigurationModule.run(ConfigurationModule.java:83)
at java.lang.Thread.run(Thread.java:662)
[2011-09-12T12:04:58.846+02:00] [as] [ERROR] [] [oracle.as.provisioning]
[tid: 14] [ecid: 0000J9Soq_rFGBWFLz6UOA1ERSJh000005,0] [[
oracle.as.provisioning.exception.ASProvWorkflowException: Error Executing workflow.
at oracle.as.provisioning.engine.WorkFlowExecutor._createDomain(WorkFlowExecutor.java:686)
at oracle.as.provisioning.engine.WorkFlowExecutor.executeWLSWorkFlow(WorkFlowExecutor.java:391)
at oracle.as.provisioning.engine.Config.executeConfigWorkflow_WLS(Config.java:866)
at oracle.as.install.bi.biconfig.standard.StandardWorkFlowExecutor.executeHelper(StandardWorkFlowExecutor.java:31)
at oracle.as.install.bi.biconfig.standard.DomainProvisioningTask.doExecute(DomainProvisioningTask.java:48)
at oracle.as.install.bi.biconfig.standard.AbstractProvisioningTask.execute(AbstractProvisioningTask.java:70)
at oracle.as.install.bi.biconfig.standard.StandardProvisionTaskList.execute(StandardProvisionTaskList.java:61)
at oracle.as.install.bi.biconfig.BIConfigMain.doExecute(BIConfigMain.java:112)
at oracle.as.install.engine.modules.configuration.client.ConfigAction.execute(ConfigAction.java:335)
at oracle.as.install.engine.modules.configuration.action.TaskPerformer.run(TaskPerformer.java:87)
at oracle.as.install.engine.modules.configuration.action.TaskPerformer.startConfigAction(TaskPerformer.java:104)
at oracle.as.install.engine.modules.configuration.action.ActionRequest.perform(ActionRequest.java:15)
at oracle.as.install.engine.modules.configuration.action.RequestQueue.perform(RequestQueue.java:63)
at oracle.as.install.engine.modules.configuration.standard.StandardConfigActionManager.start(StandardConfigActionManager.java:158)
at oracle.as.install.engine.modules.configuration.boot.ConfigurationExtension.kickstart(ConfigurationExtension.java:81)
at oracle.as.install.engine.modules.configuration.ConfigurationModule.run(ConfigurationModule.java:83)
at java.lang.Thread.run(Thread.java:662)
I have fount posts with a similar problem, but is over Windows.
I appreciate any ide/suggestion.
Thank you in advance.
Regards,

I have seen that WebLogic is shut down, so I am trying to start up, but I can't:
starting weblogic with Java version:
Unrecognized option: -jrockit
Error: Could not create the Java Virtual Machine.
Error: A fatal exception has occurred. Program will exit.
Starting WLS with line:
/usr/java/jdk1.7.0/bin/java -jrockit -Xms512m -Xmx512m
-Dweblogic.Name=AdminServer
-Djava.security.policy=/root/Oracle/Middleware/wlserver_10.3/server/lib/weblogic.policy
-Dweblogic.ProductionModeEnabled=true -da
-Dplatform.home=/root/Oracle/Middleware/wlserver_10.3
-Dwls.home=/root/Oracle/Middleware/wlserver_10.3/server
-Dweblogic.home=/root/Oracle/Middleware/wlserver_10.3/server
-Dweblogic.management.discover=true -Dwlw.iterativeDev=false -Dwlw.testConsole=false -Dwlw.logErrorsToConsole=false -Dweblogic.ext.dirs=/root/Oracle/Middleware/patch_wls1035/profiles/default/sysext_manifest_classpath:/root/Oracle/Middleware/patch_ocp360/profiles/default/sysext_manifest_classpath
weblogic.Server
Unrecognized option: -jrockit
Error: Could not create the Java Virtual Machine.
Error: A fatal exception has occurred. Program will exit.
I have modified /etc/profile, including JAVA_HOME and PATH with the java PATH. And it is ok, because if I executed java -version I can see the new jdk:
java version "1.7.0"
Java(TM) SE Runtime Environment (build 1.7.0-b147)
Java HotSpot(TM) 64-Bit Server VM (build 21.0-b17, mixed mode)
Any idea¿?

Error installing EM10gR2 Configuration assistant "Web Cache Configuration A

I am getting an error when the web cache configuration assistant is running. Here is the output of the message:
Output generated from configuration assistant "Web Cache Configuration Assistant" (attempt 2):
Command = /oracle/oms10g/jdk/bin/java -DORACLE_HOME=/oracle/oms10g -Djava.net.preferIPv4Stack=true -classpath /oracle/oms10g/sysman/webapps/emd/WEB-INF/lib/webcachecfg.jar:/oracle/oms10g/sysman/webapps/emd/WEB-INF/lib/emd.jar:/oracle/oms10g/lib/emSDK.jar:/oracle/oms10g/dcm/lib/dcm.jar:/oracle/oms10g/jlib/repository.jar:/oracle/oms10g/lib/xmlparserv2.jar:/oracle/oms10g/jlib/emConfigInstall.jar:/oracle/oms10g/jdbc/lib/classes12.zip:/oracle/oms10g/jdbc/lib/nls_charset12.jar:/oracle/oms10g/jlib/jndi.jar:/oracle/oms10g/jlib/rt.jar:/oracle/oms10g/jdk/lib/i18n.jar:/oracle/oms10g/jlib/ldapjclnt10.jar:/oracle/oms10g/jlib/ojmisc.jar:/oracle/oms10g/j2ee/home/jazn.jar:/oracle/oms10g/j2ee/home/jaas.jar oracle.ias.webcache.config.WebcacheConfig -oh /oracle/oms10g
Failed in smi manipulation().
A problem has occurred reading the initial configuration and storing it into repository
Resolution:
Please refer to the base exception for resolution, or call Oracle support.
Base Exception:
/oracle/oms10g/Apache/Apache/bin/httpd: error while loading shared libraries: libdb.so.2: cannot open shared object file: No such file or directory
Resolution:
Please make sure the values entered in OHS configuration files are correct.
oracle.ias.sysmgmt.exception.InvalidConfigurationException: Base Exception:
/oracle/oms10g/Apache/Apache/bin/httpd: error while loading shared libraries: libdb.so.2: cannot open shared object file: No such file or directory
Resolution:
Please make sure the values entered in OHS configuration files are correct.
     at oracle.ias.sysmgmt.repository.plugin.advanced.apache.StateTranslator.checkConfigFileValidity(Unknown Source)
     at oracle.ias.sysmgmt.repository.plugin.advanced.apache.StateTranslator.validateConfigDuringEvaluate(Unknown Source)
     at oracle.ias.sysmgmt.repository.plugin.advanced.apache.PlugInImpl.localConfigValidation(Unknown Source)
     at oracle.ias.sysmgmt.repository.DcmPlugin.localConfigValidation(Unknown Source)
     at oracle.ias.sysmgmt.repository.RepositoryImpl.performLocalValidation(Unknown Source)
     at oracle.ias.sysmgmt.repository.SyncUpHandler._updatePluginConfigData(Unknown Source)
     at oracle.ias.sysmgmt.repository.SyncUpHandler.syncUpFromLocalFiles(Unknown Source)
     at oracle.ias.sysmgmt.repository.RepositoryImpl.syncUpFromLocalFiles(Unknown Source)
     at oracle.ias.sysmgmt.utility.editpropagator.PropagateLocalEdit.repositoryInit(Unknown Source)
     at oracle.ias.sysmgmt.persistence.utility.PMUtility.initConfiguration(Unknown Source)
     at oracle.ias.sysmgmt.task.TaskMaster.initConfiguration(Unknown Source)
     at oracle.ias.sysmgmt.task.TaskMaster.sysInit(Unknown Source)
     at oracle.ias.sysmgmt.task.TaskMaster.sysInit(Unknown Source)
     at oracle.ias.sysmgmt.task.InstanceManager.sysInit(Unknown Source)
     at oracle.ias.sysmgmt.task.InstanceManager.init(Unknown Source)
     at oracle.ias.sysmgmt.EntryPoint.init(Unknown Source)
     at oracle.ias.webcache.config.WebcacheConfig.smiSetup(WebcacheConfig.java:483)
     at oracle.ias.webcache.config.WebcacheConfig.smiEnableWebcache(WebcacheConfig.java:454)
     at oracle.ias.webcache.config.WebcacheConfig.enableConfiguration(WebcacheConfig.java:299)
     at oracle.ias.webcache.config.WebcacheConfig.main(WebcacheConfig.java:87)
Configuration assistant "Web Cache Configuration Assistant" failed
The "/oracle/agent10g/cfgtoollogs/configToolFailedCommands" script contains all commands that failed, were skipped or were cancelled. This file may be used to run these configuration assistants outside of OUI. Note that you may have to update this script with passwords (if any) before executing the same.-----------------------------------------------------------------------------
My etc/hosts file looks like:
cat /etc/hosts
# Do not remove the following line, or various programs
# that require network functionality will fail.
127.0.0.1 localhost.localdomain localhost
172.24.254.25 k25
Ugh!

sorry, a little bit late but i had the same problem.
/oracle/oms10g/Apache/Apache/bin/httpd: error while loading shared libraries: libdb.so.2: cannot open shared object file: No such file or directory
simple make the link "ln -s libdb.so.3 libdb.so.2" in the /usr/lib directory.
regard´s
roland

9iAS 1.0.2.2/Portal 3.0.9 - Installation Error at "Portal Configuration Assistant"

I was installing the iAS1.0.2.2 and at the Portal Configuration Assistant, at the 23% I received the following error:
"An unexpected error ocurred during the Install Process. Check the install.log ....."
(FYI this is the second time I try to install it and in both cases I received the same error at the same point, so I decided to ask for help)
At the end of the Install.log is the following:
=====================
STEP 7 : Installing WWC layer Components
INSTALL_ACTION : installWWC(): ..\..\bin\sqlplus portal30/portal30@<DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)HOST=administrator)(PORT=1521)))(CONNECT_DATA=(SID=virtual))) @..\..\portal30\admin\plsql\wwc\wwcinst.sql portal30 USERS TEMP wvinswwc.log USERS USERS portal30_NULL portal30_sso portal30_DEMO
ORA-00439: feature not enabled: Function-based indexes
Errors encountered in the Install process. Installation Aborted
=========================
I noticed during the installation, before the Configuration Assistant (aprox at 97%), the installation opened a DOS session and I could see some errors with some Indexes but I don't know in which Log are registered. maybe it can help to troubleshoot my above problem?
Operating System: NT4 SP6
Database: 8.1.7.0 standard edition
iAS 1.0.2.2 standard edition
both under the same machine
Let me know if there is any other info I can provide.
Tks in advance!

There has been some confusion around certification on SE over the past week. I want to clarify the situation.
We discovered an issue with the Portal on SE last week. We inadvertently used function based and bitmapped indexes (EE only features). This issue has been masked to date because the install proceeded normally after the errors were raised. In 3.0.9 we made the install more strict in that it will stop by default if it hits an unexpected error.
On further research, we have determined that these errors have little or no impact on the general functioning of the product and as such are maintaining the position that Portal 3.x is indeed certified on 8.1.7
Standard Edition.
There is unfortunately a necessary work around to the install issue (which we will rectify as soon as possible). In order to install on SE, you must execute the Oracle Portal Configuration Assistant (OPCA) from
the command line and specify the "verbose" mode (see next post). In this mode, the errors are ignored and the install proceeds appropriately.
Regards,
The Oracle9iAS Portal Development Team

Configuration Assistant Problems

Similar Messages

Maybe you are looking for