Configuration Change Error

Hi,
T-Code: Solar02 Configuration. I have created a business Process for sales order creation. Process Steps are Inquiry, Quotation, Sales Order.
But when I click on Execute button for Inquiry It showing information
" No system found for component SAP R/3 and role 'Development System' in project TEST_BCL"
Pls suggest the solution.
Regards
PK.

Hi,
Add the Logical Component of R/3 System to your Project under System Landscape in SOLAR_PROJECT_ADMIN.
If its already added, do check the Log Component & RFC in SMSY Txn.
Thnx,
Waseem.

Similar Messages

[TP x120e] Continuous "Configuration changed - Restart the system." error

I played with my bios (disabled/enabled mic, webcam, LAN and so), but after exiting the bios, Thinkpad x120e reboots continuously with the error message "Configuration changed - Restart the system.". I was not able to boot from any USB/HDD and also I can not enter to the BIOS. Hard bios reset won't help. Any ideas?
Thanks!

Hello,
Have you tried unplugging all power, including the internal CMOS/RTC backup battery, from the ThinkPad X120e, leading the unit alone for a few minutes to let any capacitors holding a residual electic charge drain, holding down the power button for 30 seconds to complete the operation, then plugging in the AC charger without either of the batteries installed, then holding down the F1 key while pressing the power button to see if that gets you into the BIOS settings?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Help me configure Change request management !!!

Dear friends,
I am Going to Configure Change request Management, so just to ensure that the configuration is not erronous, i would need Expert advise..
Just want to know Clear few things before i proceed..
I am also refering SPRO and related notes
Scenario :
I have two SYSTEMS SAP ECC 6.0 with System id R03 and Soluiton manager with SYSTEM id SOL,
R03 has 3 clients, 300 600 700..
In R03 300 is the development client, 600 is quality client, 700 is the production client.
SOL has 2 clients, 100, 200
With 200 as the production client.
Q.1) Do i have to configure CHARM in both the client (100 and 200 of SOLMAN).
Q.2) Initially I had tried to set CHARM in client 100 of solman, but later on realized that it has to be set up in client 200.
When i logon to client 200 and Execute IMG activity Spro-> sap soltion manger->basic settings-> sap solution manager system->activate integration with change request management.
Then by default it take the previous client ( client 100) as the change request management client.
( as we know there are three steps in the above activity ), the other activity are executed properly, only prblem being that the default client is always set to 100, which should not be the case).
I do get the prompt saying ( "The change request clent is set to clent 100, do u want to change to client 200, on clicking yes, still it is always set the same client 100 as charm client ")
Plz let me know what do i do to set the change request client to 200??
Q.3) Regarding TMS, we have local domain controller in solman and local domain in R3.
We are planing to establish domain links between the two systems( ie both the domain controllers) ??
Is this the right strategy ??
Any other method that u can recommend ??
Q.4)One of the IMG activity says, Generate Destinations to client 000 of all the domain controllers..
Whenever i do this these, destinations are created with errors, i am not able to create trusted RFC destinations without errors.
When i logon to satellite domain controler and excecute sm59 there are 2 destinations created Trusted and BACK.
These destinations works well,
but when i logon to Solman, got to sm59 , when i test the TMW and TRUSTED rfc destinations i test these destinations using Remote Logon i get error,
" no authorization to logon as trusted system"
I went thru one note which recomended Kernel upgrades to solve the problem,
I r3 my kernel relaese is 700 with patch level 56, the note recomends to apply patch 80, did u have these problems??
what is your kernel patch levels in sateliite and solman systems.
Q.5) TO be able to raise tickets from R3 to solman we create RFC destinations.
We also create RFC destinations to client 000 of all the sateliite system,
dont u think these RFC destinations might interfere with each other??
Q.6) Is there anyone who has successfully configured CHARM. Can you plz share the configuration documents with me..
Please note :
All the contributors would be handesomely rewarded with points .

Hi,
Check this
Note 128447 - Trusted/Trusting Systems
For your Q4.
Q3.)
Establishing Domain link - That's the right way. Go ahead.
These are the steps.
1.Define Transport Routes for System Landscape
assign exactly one development system to a production system, and that these two systems are connected by exactly one unique transport track. If a development system and a production system are connected by more than one transport track, this may lead to inconsistencies within the transport distribution. This type of transport configuration cannot be supported by Change Request Management, and may cause inconsistencies within the tools involved.
2. Activate Extended Transport Control
The CTC parameter should be '1'
3.Configure Transport Strategy
Deactivate the QA Approval.
4. Activate Trusted Services.
5.Activate Domain Links.
You have to activate domain link between systems.
6. Generate RFC Destinations to Client 000
Hope this helps.
feel free to revert back.
--Ragu

Configuration Check Error in Managed System Configuration

Hi dear experts,
I come across a problem as the screenshot shows blew:
I check some relevant information, but no issues found:
1.
DEWDFLSSC5062:/usr/sap/hostctrl/exe # ./saphostexec -status
saphostexec running (pid = 7094)
sapstartsrv running (pid = 7097)
10:46:34 24.06.2014 LOG: Using PerfDir (DIR_PERF) = /usr/sap/tmp
saposcol running (pid = 7130)
DEWDFLSSC5062:/usr/sap/hostctrl/exe # cat host_profile
SAPSYSTEMNAME = SAP
SAPSYSTEM = 99
service/porttypes = SAPHostControl SAPOscol SAPCCMS
DIR_LIBRARY = /usr/sap/hostctrl/exe
DIR_EXECUTABLE = /usr/sap/hostctrl/exe
DIR_PROFILE = /usr/sap/hostctrl/exe
DIR_GLOBAL = /usr/sap/hostctrl/exe
DIR_INSTANCE = /usr/sap/hostctrl/exe
DIR_HOME = /usr/sap/hostctrl/work
service/admin_users = daaadm
service/logfile_000 = /tmp/s
service/logfile_001 = /usr/sap/DAA/SMDA97/SMDAgent/log/smdagent_trace*.trc
service/logfile_002 = /usr/sap/DAA/SMDA97/SMDAgent/log/smdagent_trace.*.trc
service/logfile_003 = /usr/sap/DAA/SMDA97/SMDAgent/log/smdagent_trace.trc
And the version of hostagent is up-to-date.
2.The URL
- http://<SMDhost>:1128/SAPOscol/?wsdl
- http://<SMDhost>:1128/SAPHostControl/?wsdl
can be accessed.
3.The step 3 in managed systems configuration is executed successfully.
4.I have even uninstalled and re-installed the SMD and hostagent, and change the alert_timeout parameter in T-code DMD, but the issue insisted.
5.Only a few SMDs in my landscape, so I think the parameter MaxThreadCount, InitialThreadCount, MinThreadCount should be no problem.
Now I have no idea how to proceed, please give me some advice, thank you in advance.
Best Regards,
Pany Pan

Hi Pany
Kindly check the below two sapnote
1935653 - Error "A timeout occured during the execution of the OS Command Console" when performing a Managed System Configuration - Solution Manager 7.1
1865122 - Solution Manager 7.10 Configuration Check errors : "A timeout occured during the execution of the OS Command Console" "An unexpected error occured"
Moreover , you need to check/verify/maintain the parameter in configtool
ThreadManager -> MaxThreadCount
Total number of Diagnostics Agents * 2 + 50
1250
ThreadManager -> InitialThreadCount
Total number of Diagnostics Agents * 1.5
900
ThreadManager -> MinThreadCount
Total number of Diagnostics Agents
600
ConnectionManipulator -> maxSoTimeOutConnections
Total number of Diagnostics Agents * 1.35
810
ConnectionManipulator -> MaxParallelUsers
Total number of Diagnostics Agents + 50
650
In Diagnostics Agent Troubleshooting - SAP Solution Manager Setup - SCN Wiki
guide check the section Required Solution Manager Java Stack Settings (Scalability)
I face the same issue , which got resolved by maintaining the above parameters, maxthreadCount,
minthreadcount , maxSoTimeOutConnections.
With Regards
Ashutosh Chaturvedi

How to prevent BGP code 6 (Cease) subcode 6 (Other Configuration Change)

Can anyone tell How to prevent BGP code 6 (Cease) subcode 6 (Other Configuration Change) ?
We are facing frequent problem with this error. Please suggest how to stop this....
Note :- We are using BGP VPN between this peers.
Logs :
Date/Time : 2015-04-30 00:49:40+05:30
State : Up
Date/Time : 2015-04-30 00:39:05+05:30
State : Down
Error Code : 6(CEASE)
Error Subcode : 6(Other Configuration Change)
Notification : Send Notification
Date/Time : 2015-04-29 18:22:11+05:30
State : Up
Date/Time : 2015-04-29 18:21:39+05:30
State : Down
Error Code : 6(CEASE)
Error Subcode : 6(Other Configuration Change)
Notification : Send Notification

on the same dates you mean the same request are posted in IT2001? ie both full days?
Please clarify
usually the Time collision checks are followed only via posting using report rptarqpost and not while applying through portal in ESS
This is very strange you indicate
SO you need to check the basic tables first
You may need to check the collision.
Collisions Tables V_T554Y and V_554Y_B reaction indicators.
and V_T508A
able T582A set to time constraint of "Z
In backend Pa30 collision works like this
1) the logical collision, checks if there is an overlap in the validity
interval of the IT´s (begda, endda).
2) the physical collision, checks if there is an overlap in the time
interval of the IT's.
In the logical collision it is checked if there is an overlap in the
validity interval if at least one of the records is a full-day
( that is the case when you enter a Daily Work Schedule (DWS) )
So when one of the records has a DWS it is considered to be a full day
record and the logical collision is taken into consideration.
If instead you enter the only the time interval manually the records
are considered to be partial-day and the physical collision is
performed. In that case only the time interval is important.
So if the clock times are not entered the physical collision can not
take place.
The collision functionality is always based on clock times and dates,
never on the total nr of hours.
Edited by: Siddharth Rajora on Sep 21, 2011 4:57 PM

Is there a way to restart my Java cloud service? What are "non-dynamic configuration changes"?

I am trying to deploy an ADF application to my trial instance of Java cloud, I am getting the following error:
2013-10-15 08:24:18 CDT: Deploy Application started
2013-10-15 08:24:19 CDT: weblogic.management.DeploymentException: [Deployer:149189]An attempt was made to execute the 'deploy' operation on an application named 'xyzAPP' that is not currently available. The application may have been created after non-dynamic configuration changes were activated. If so, the operation can not be performed until server is restarted so that the application will be available.
2013-10-15 08:24:19 CDT: WL action state: failed
2013-10-15 08:24:19 CDT: Action FAILED with WL action state: failed
2013-10-15 08:24:19 CDT: Check the server log of your Java cloud service for more info about the failure.
There are tutorials available for deploying your first ADF app to the cloud, which I followed carefully. Except for one thing, the ADF app was originally developed in Jdeveloper 11.1.2.4 and then migrated to 11.1.1.6. Could that be what is causing the problem? How can I try to troubleshoot this?

Hi,
You will have to raise an sr towards the hosting team to perform the restart.
Kind regards,
Flori

Configuration Validation error when booking an Sales Order.

Hi,
Getting an error when booking an sales order ie; "Configuration Validation error".
We are upgrading from 11.5.8 to 12.1.1 and this issue is critical. Please provide your valuable suggestion and advice.
Thanks in advance,
Asif

It seems you use configurator. Is this happening in production or in some test instance?
If it is a test instance, when was it cloned from prod? Did you clone the configurator instance at the same time?
1) You should publish the configurator model from the configurator developer to this new instance.
2) Also, it is possible that the selections made during order entry earlier are not valid anymore due to ECO/BOM changes or due to configurator rule changes. Open the configuration, make any selections if necessary and then click ok.
This will repopulate the order lines then you should be able to book the order.
Hope this helps
Sandeep Gandhi
Independent Techno-functional Consultant

Please ensure that the applicationhost.config file is correct and recommit the last configuration changes made

I am receiving event ID 5189 on Server 2008 R2, IIS 7.5. I experience this error across a number of servers, each of which is running only the default web site, but have 600+ applications running on the default web site. Each application
has its own application pool. My point is, the applicationhost.config is rather large.
I have seen a number of posts on this error message, but my issue itself seems to differ somewhat. I am aware of a similar post: http://social.technet.microsoft.com/Forums/en-US/3128ee93-1319-4cc2-9257-003512caf476/event-id-5189-microsoftwindowswas?forum=exchangesvrgeneral
which points to KB http://technet.microsoft.com/en-us/library/cc734988%28v=ws.10%29.aspx
However, in my case, it doesn't seem that the extreme measures for this resolution are required. The error usually indicates a corrupted applicationhost.config that must be manually fixed, or otherwise the WAS service needs to be restarted, or the
server itself, etc.
In my case, the issue can usually be fixed by an application pool recycle, or at worst a stop/start. I have an application which is sensitive to recycles, and so we do not have periodic recycle events configured for this application, which is the bulk
of the applications on the servers. It seems to me that this issue is usually caused by the application being in use when there is an applicationhost.config change.
For instance, we have one application that we deploy using msdeploy. We found that when we ran an installation for this application via msdeploy, we were receiving this event, and we would subsequently get 500 errors in the application (sometimes the
application pool corresponds to that which is identified in the event log, sometimes it doesn't).    It seems like applications that were being hit at the time the applicationhost.config was modified by msdeploy were affected. In an attempt
to correct this, we moved from msdeploy to a batch file containing appcmd commands. This also did not resolve the issue.
I have another application which is installed using PowerShell commandlets. We started to notice that this script also caused the issue to occur on occasion. As I continued to identify different processes that resulted in the same issue, I came
to the conclusion that this is likely due to any change in the applicationhost.config. I assume the issue is that the applicationhost.config is modified during a read operation to the file by the application pool, or WAS service, and that the recycle
event, which corrects the issue, forces a re-read of the applicationhost.config, resolving the bad-read issue.
Has anyone else experienced this, or do you have any recommendations? My current work-around is to not install any applications during peak hours, and performing an IISRESET after installs are completed, to ensure application stability.
Message              : The Windows Process Activation Service failed to generate an application pool config file for application pool 'myAppPool'. The error type is '7'. To resolve this issue,
please ensure that the applicationhost.config file is correct and recommit the last configuration changes made. The data field contains the error number.
Id                   : 5189
Version              : 0
Qualifiers           : 49152
Level                : 2
Task                 : 0
Opcode               : 0
Keywords             : 36028797018963968
RecordId             : 324108
ProviderName         : Microsoft-Windows-WAS
ProviderId           : 524b5d04-133c-4a62-8362-64e8edb9ce40
LogName              : System
ProcessId            : 0
ThreadId             : 0
MachineName          : MyComputer
TimeCreated          : 3/3/2014 9:03:24 PM
ContainerLog         : system
MatchedQueryIds      : {}
Bookmark             : System.Diagnostics.Eventing.Reader.EventBookmark
LevelDisplayName     : Error
KeywordsDisplayNames : {Classic}
Properties           : {System.Diagnostics.Eventing.Reader.EventProperty, System.Diagnostics.Eventing.Reader.EventProperty, System.Diagnostics.Eventing.Reader.EventProperty}

As an update to this issue, after doing some research, it appears the behavior is related to a new feature in IIS7 called Application Pool Isolation (http://technet.microsoft.com/en-us/library/dd163536.aspx).
This new feature prevents cross-application spillage by isolating the configuration for each application pool in IIS. So in reality, an application pool never actually reads the applicationhost.config - that is just a master file, and each time it
is update, it triggers a change to the individual application pool configuration files, located in C:\inetpub\temp\apppools.
We did try setting Advanced Settings > Disable Recycling for Configuration Change to true, but after an IIS reset we were still able to reproduce the issue - worse actually, because in our test program, which continually hits the web
service, and also continually makes apphost.config changes, when the two events collide, the 500.19 issue precipitates; but after an additional change to the apphost.config, it seems that the additional changes will actually correct the issue (seemingly forcing
another recycle, which is also how we resolve the issue manually); after making this setting adjustment, once the 500.19 issue precipitates, additional changes to the apphost.config does not correct the problem, only a manual recycle corrects it. This
is the recycling.disallowRotationOnConfigChange property of the app pool. We also set the setting for recycling.disallowOverlappingRotation to True as well, with the same result.
We ARE able to prevent this issue by setting the C:\inetpub\temp\apppools\myapppool\myapppool.config to read-only, but for obvious reasons, this is not a desired work-around.
It seems like what is happening is that any change to the ApplicationHost.config is resulting in each of the C:\inetpub\temp\apppools temp application pool config files being updated as well, in addition to triggering an application pool recycle. It
seems to me the desired behavior would be that these files are only updated if the applicationhost.config changes are specific to that application pool - but that doesn't seem to be the behavior.
After turning on failed request tracing, I was able to narrow the error down more:
ModuleName
AnonymousAuthenticationModule
Notification
2
HttpStatus
500
HttpReason
Internal Server Error
HttpSubStatus
19
ErrorCode
2147942413
ConfigExceptionInfo
\\?\C:\inetpub\application\application\web.config ( 9) :Failed to decrypt attribute 'password'
Notification
AUTHENTICATE_REQUEST
ErrorCode
The data is invalid. (0x8007000d)
This seems to be pretty static. Trying to look into possible causes of this issue.

Synchronize configuration changes among SUN One Application cluster

How to do the synchronization of configuration changes among the SUN One Application clustering.
I need to replicate the configuration changes from Appserver1 to appserver2, which is in the cluster farms.
Prakash

hi i'm a colleague of Mirza.
We have modified the web.xml and now server is asking for password. We dont want to specify a particular role name in authorization-constraint. We need all our authenticated users to access the application. When i remove the auth-constraint tag from the web.xml it does not not allow the user to acess the application and gives me the error "Access to the specified resource has been forbidden". To remedy this we have created a group called "authenticated" in our ldap directory server and put all the users in that group. Now even though i'm specifying in auth-constraint .. the role-name to be "authenticated" but its still not granting the user permission to the access the application.
here is the snippet of my web.xml
<security-constraint>
<web-resource-collection>
<web-resource-name>PAMS</web-resource-name>
<url-pattern>/*</url-pattern>
<http-method>GET</http-method>
<http-method>POST</http-method>
</web-resource-collection>
<auth-constraint>
<role-name>authenticated</role-name>
</auth-constraint>
</security-constraint>
<login-config>
<auth-method>BASIC</auth-method>
<realm-name> ldap</realm-name>
</login-config>
<security-role>
<role-name>authenticated</role-name>
</security-role>
I need to know what ever I am doing is correct.

Cannot save configuration changes on catalyst 3548

i have an old switch that worked when last on network. powered on normally, but when i attempt to make configuration changes (copy running config startup config), it fails. where can i find information on working with file systems Version 12.0(5.3)WC(1), MAINTENANCE INTERIM SOFTWARE

hi, thanks for the followup. i appreciate it. i am sure the is corruption in the config.text file but am having a problem deleting it. i have copied a number of errors, listed below.......
va-research-3548-06#copy runn start
Destination filename [startup-config]?
Building configuration...
intel_28f320j5_write_bytes: flash busy error
flashfs[1]: writing to flash handle 0x4E4E34, device 0, offset 0x360000, length
0x208: Operation Failed
flashfs[1]: sector ptr: {0x1B, 0xA0}
nv_done: unable to open "flash:config.text.new"[OK]
va-research-3548-06#
va-research-3548-06#dir
Directory of flash:/
%Error opening flash:/ (Device or resource busy)
3612672 bytes total (476160 bytes free)
va-research-3548-06#
va-research-3548-06#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Ve
INTERIM SOFTWARE
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Mon 30-Apr-01 07:51 by devgoyal
Image text-base: 0x00003000, data-base: 0x003331F4
ROM: Bootstrap program is C3500XL boot loader
va-research-3548-06 uptime is 4 days, 16 hours, 36 minutes
System returned to ROM by reload
System image file is "flash:c3500XL-c3h2s-mz-120-5.3.WC.1.bin"
cisco WS-C3548-XL (PowerPC403) processor (revision 0x01) with 16384K/1024K bytes
of memory.
Processor board ID FAB0528V1LZ, with hardware revision 0x00
Last reset from warm-reset
Processor is running Enterprise Edition Software
Cluster command switch capable
Cluster member switch capable
48 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:06:53:A9:14:40
Motherboard assembly number: 73-3903-08
Power supply part number: 34-0971-01
Motherboard serial number: FAB052572SW
Power supply serial number: PAC052300EI
Model revision number: A0
Motherboard revision number: C0
Model number: WS-C3548-XL-EN
System serial number: FAB0528V1LZ
Configuration register is 0xF
va-research-3548-06#
va-research-3548-06#dir flash:
Directory of flash:/
2 -rwx 1749748 Apr 30 2001 07:54:49 c3500XL-c3h2s-mz-120-5.3.WC.1.bin
3 -rwx 94375 Apr 30 2001 07:54:49 c3500XL-diag-mz-120-5.3.WC.1
4 drwx 10176 Feb 28 1993 16:00:55 html
5 -rwx 272 Dec 31 1969 16:00:20 env_vars
165 -rwx 4337 Feb 28 1993 18:06:35 config.text
166 -rwx 1096 Mar 01 1993 15:41:40 vlan.dat
3612672 bytes total (476160 bytes free)
va-research-3548-06#del
va-research-3548-06#delete flash:config.text
Delete filename [config.text]?
Delete flash:config.text? [confirm]
intel_28f320j5_write_bytes: flash busy error
flashfs[1]: writing to flash handle 0x4E4E34, device 0, offset 0x360000, length
0x208: Operation Failed
flashfs[1]: sector ptr: {0x1B, 0x9B}
flashfs[1]: filesystem marked down. Use "fsck" to recover.
%Error deleting flash:config.text (I/O error)
va-research-3548-06#

BGP Notification received, configuration change

Hi,
We are monitoring a BGP peering flap for a fraction of seconds approximately every three days for a particular neighbor. We are seeing this behavior consistently for a Month.
Jun 10 08:55:15.566 NST: bgp[1041]: %ROUTING-BGP-5-ADJCHANGE : neighbor x.x.x.x Down - BGP Notification received, configuration change (VRF: default)
Jun 10 08:55:15.565 NST: bgp[1041]: %ROUTING-BGP-5-NBR_NSR_DISABLED_STANDBY : NSR disabled on neighbor x.x.x.x on standby due to BGP Notification received (VRF: default)
Would like to know what does the error messge indicates "BGP Notification received, configuration change"

There might be a clue in the bgp trace on the device that experienced this condition:
show bgp trace and look around the time of the notification down.
Depending on what is on the other side, I think that hte investigation is better done on that node as that was the originator of the change hence bringing the peer down.
This can be as simple as an address family add or remove, things like that. When capabilities of a peer change, they have to bring down the peering since they are only sent in the OPEN message.
IF it is very periodic, I would also verify and check what might be happening during those time windows, especially on the peer. Maybe there is a config script that could induce things.
If that peer is an XR device, the bgp trace will be very helpful in that regard.
If itis an IOS device, then maybe you need to keep running some debug bgp event for around the time that you expect this flap, and a syslog analysis (sh log) around that time for clues.
xander

ACS Applying configuration changes failed

Hello
I have a problem with ACS version 5.1.0.44.6. running on 1120 appliance.
After making some changes to authorization rules of Device Admin access services, I can no loger access authorization page for Device admin access services. Error on Access Policies page is: . This System Faliure occurred: {0}. Your changes have not been saved. Click OK to return to the list page.
Logs recorded this:
Severity
FATAL
Message
Applaying configuration changes failed
Category
CSOacs_Internal_Opreations_Diagnostics
Code
31102
Details
LastErrorMessage=Policy DB problem: Policy value type is not supported. ConfigTransactionID=2968
After this we can no longer authenticate on any device with TACACS+. Telnet from switch to the ACS server on port 49 returns % Connection refused by remote host. RADIUS authentication and authorization for VPN users on same server is working fine.
Do you have any idea how to solve this problem?
Hrvoje

Thanks for the screenshot!
It appeared to be an issue in StatusMonitor that I also could reproduce: we don’t work correctly with the structure when virtual directories and applications are mixed, i.e. due to this bug we cannot find web application if it’s under the virtual directory,
that’s under the web site.
I.e. app named WebSite/Dir/App1 cannot be found by SM during adding application insights:
WebSite
   ---> Dir (virtual directory)
          ---> App1 (web application)
We'll triage this bug and address in one of the nearest StatusMonitor updates.
Thanks for finding this issue!

Collection Segment closed due to configuration change

Hi
Our collection supervisor had created new collection groups and assigned them to the colleciton segment. But when she goes into the UDM_BP_GRP transaction to change the collection group assignment to the BP, she is getting this error message:
UDM_BUPA_MSG002 - Collection Segment closed due to configuration change
But the collection segments are still released, assigned to the collection profile. Nothing has changed except that new collection groups have been added.
Has anyone seen this issue before?
Thanks,
Chait

Mark,
Thanks for your reply. The new groups are assigned to the collection segments in the same profile. I tried to change the profile manually in BP thinking that would refresh the segments. But it did not make any difference. Note that it is UDM_BP_GRP that is not working, we can still change the group in the BP directly (UDM_BP).
I never had this issue before and I couldn't find anything on OSS.

CR10 Dev JRC ReportSDKException Report location is not specified in the configuration file error

I'm trying to embed a simple report into a j2ee application running under BEA WebLogic(without
workshop)
using the standalone Java Reporting Component (JRC), but I'm getting the exception
shown below (along with my config and source).
I'm just wondering at the cause of the exception, because I can successfully deploy
this code to jboss.
I've tried moving the CrystalReportEngine-config.xml file everywhere, from the
/WEB-INF/classes/ folder
to the /WEB-INF/ folder to the /WEB-INF/lib/ folder.
I consulted the product documentation on the JRC and its tutorials but it has
me stumped.
I went through the BEA WebLogic Workshop tutorial, which worked for some reason,
but I'm looking to do all the coding manually without any of BEA's controls and
what not.
Any information would be GREATELY APPRECIATED!!!
Thanks,
-Colin
com.crystaldecisions.sdk.occa.report.lib.ReportSDKException: Report location is
not specified in the configuration file---- Error code:-2147
215356 Error code name:fileNotOpened
at com.crystaldecisions.sdk.occa.report.lib.ReportSDKException.throwReportSDKException(Unknown
Source)
at com.crystaldecisions.reports.reportengineinterface.JPEReportSource.<init>(Unknown
Source)
at com.crystaldecisions.reports.reportengineinterface.JPEReportSource.a(Unknown
Source)
at com.crystaldecisions.reports.reportengineinterface.JPEReportSourceFactory.createReportSource(Unknown
Source)
at com.crystaldecisions.report.web.viewer.ReportAgentBase.case(Unknown
Source)
at com.crystaldecisions.report.web.viewer.ReportServerControl.getReportSource(Unknown
Source)
at com.crystaldecisions.report.web.viewer.taglib.ReportServerControlTag.int(Unknown
Source)
at com.crystaldecisions.report.web.viewer.taglib.ReportServerControlTag.doEndTag(Unknown
Source)
at jsp_servlet.__viewreport._jspService(__viewreport.java:197)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:33)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:446)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
My EAR file structure is as follows:
/crystal/ (context)
/reports/qtrade_sp_listing.rpt
/crystalreportviewers10/ -- bunch of crystal viewing stuff
/WEB-INF/classes/CrystalReportEngine-config.xml
/WEB-INF/lib/ -- bunch of crystal jar files
My CrystalReportEngine-config.xml is as follows
<?xml version="1.0" encoding="utf-8"?>
<CrystalReportEngine-configuration>
<reportlocation>../..</reportlocation>
<timeout>10</timeout>
<keycode>A2960-01C00FA-U700063</keycode>
</CrystalReportEngine-configuration>
My relevant Web.xml looks like:
<web-app>
<context-param>
<param-name>crystal_image_uri</param-name>
<param-value>/crystal/crystalreportviewers10/</param-value>
</context-param>
<taglib>
<taglib-uri>/crystal-tags-reportviewer.tld</taglib-uri>
<taglib-location>/WEB-INF/crystal-tags-reportviewer.tld</taglib-location>
</taglib>
</web-app>
My JSP Page Source:
<%@ page language="java" contentType="text/html;charset=UTF-8"%>
<%@ taglib uri="/crystal-tags-reportviewer.tld" prefix="crviewer"%>
<html>
<head>
<title>Web Application Page</title>
</head>
<body>
<crviewer:viewer
viewerName="SPListingReport"
reportSourceVar="_SPListingReport"
displayGroupTree="false"
displayToolbarToggleTreeButton="false"
reportSourceType="reportingComponent">
<crviewer:report reportName="reports/qtrade_sp_listing.rpt"></crviewer:report>
</crviewer:viewer>
</body>
</html>

I'm trying to embed a simple report into a j2ee application running under BEA WebLogic(without
workshop)
using the standalone Java Reporting Component (JRC), but I'm getting the exception
shown below (along with my config and source).
I'm just wondering at the cause of the exception, because I can successfully deploy
this code to jboss.
I've tried moving the CrystalReportEngine-config.xml file everywhere, from the
/WEB-INF/classes/ folder
to the /WEB-INF/ folder to the /WEB-INF/lib/ folder.
I consulted the product documentation on the JRC and its tutorials but it has
me stumped.
I went through the BEA WebLogic Workshop tutorial, which worked for some reason,
but I'm looking to do all the coding manually without any of BEA's controls and
what not.
Any information would be GREATELY APPRECIATED!!!
Thanks,
-Colin
com.crystaldecisions.sdk.occa.report.lib.ReportSDKException: Report location is
not specified in the configuration file---- Error code:-2147
215356 Error code name:fileNotOpened
at com.crystaldecisions.sdk.occa.report.lib.ReportSDKException.throwReportSDKException(Unknown
Source)
at com.crystaldecisions.reports.reportengineinterface.JPEReportSource.<init>(Unknown
Source)
at com.crystaldecisions.reports.reportengineinterface.JPEReportSource.a(Unknown
Source)
at com.crystaldecisions.reports.reportengineinterface.JPEReportSourceFactory.createReportSource(Unknown
Source)
at com.crystaldecisions.report.web.viewer.ReportAgentBase.case(Unknown
Source)
at com.crystaldecisions.report.web.viewer.ReportServerControl.getReportSource(Unknown
Source)
at com.crystaldecisions.report.web.viewer.taglib.ReportServerControlTag.int(Unknown
Source)
at com.crystaldecisions.report.web.viewer.taglib.ReportServerControlTag.doEndTag(Unknown
Source)
at jsp_servlet.__viewreport._jspService(__viewreport.java:197)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:33)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:446)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
My EAR file structure is as follows:
/crystal/ (context)
/reports/qtrade_sp_listing.rpt
/crystalreportviewers10/ -- bunch of crystal viewing stuff
/WEB-INF/classes/CrystalReportEngine-config.xml
/WEB-INF/lib/ -- bunch of crystal jar files
My CrystalReportEngine-config.xml is as follows
<?xml version="1.0" encoding="utf-8"?>
<CrystalReportEngine-configuration>
<reportlocation>../..</reportlocation>
<timeout>10</timeout>
<keycode>A2960-01C00FA-U700063</keycode>
</CrystalReportEngine-configuration>
My relevant Web.xml looks like:
<web-app>
<context-param>
<param-name>crystal_image_uri</param-name>
<param-value>/crystal/crystalreportviewers10/</param-value>
</context-param>
<taglib>
<taglib-uri>/crystal-tags-reportviewer.tld</taglib-uri>
<taglib-location>/WEB-INF/crystal-tags-reportviewer.tld</taglib-location>
</taglib>
</web-app>
My JSP Page Source:
<%@ page language="java" contentType="text/html;charset=UTF-8"%>
<%@ taglib uri="/crystal-tags-reportviewer.tld" prefix="crviewer"%>
<html>
<head>
<title>Web Application Page</title>
</head>
<body>
<crviewer:viewer
viewerName="SPListingReport"
reportSourceVar="_SPListingReport"
displayGroupTree="false"
displayToolbarToggleTreeButton="false"
reportSourceType="reportingComponent">
<crviewer:report reportName="reports/qtrade_sp_listing.rpt"></crviewer:report>
</crviewer:viewer>
</body>
</html>

Change error message to warning message

Hi Experts,
How can we change error message to warning message.
Eg: T-code : SE91 shows the message. If i want to change message class PG, message no 26 error to warning what will be the process.
Regards
Ratan

Hi Ratan,
Message class PG is used in the below mentioned Standard SAP Methods and Includes, So it is not suggested to change the SAP standard code.
Regards,
Raja Sekhar

Configuration Change Error

Similar Messages

Maybe you are looking for