Configuration change Log
Hi,
I need to find the configuration change log in development system. Do we have any transaction/report/program from which we can track all the configuration changes for a perticular object.
Thanks,
Vijay
for almost all customizing you can find the change history in menu tools within the cuistomizing.
Similar Messages
-
Configuration Change log in Production
Hi all
Some configuration changes have been directly made in production at our client. How can we find out what changes are made? Going into SCC4 > Change logs, I could find out who made all the changes. But it does not show what configuration changes are made.
Thanks
VamsiDear Vamsi,
I'm not sure whether in a single report you can fetch all the changes related to configuration for a particular module.
But I'm sure in most of the nodes the configuration change logs gets recorded.Check these links,
Re: How to find when a new Material type is created
Configuration change Log
Regards
Mangalraj.S -
Configuration change logs with EEM
Hi,
I am trying to log all commands executed on the Cisco Router. And it is working fine. However it wont show who executed the commands. It just shows command was executed
*Nov 15 00:38:56.356: %HA_EM-6-LOG: cli-match: configure terminal Command Executed
*Nov 15 00:39:08.060: %HA_EM-6-LOG: cli-match: do-exec sh ip int brief Command Executed
*Nov 15 00:39:08.066: %HA_EM-6-LOG: cli-match: show ip interface brief Command Executed
PE4(config)#
*Nov 15 00:39:12.940: %HA_EM-6-LOG: cli-match: do-exec sh logg Command Executed
*Nov 15 00:39:12.945: %HA_EM-6-LOG: cli-match: show logging Command Executed
I know i can setup using config archive logging for the config change. but my requirement is for show command as well. We use radius for authentication and it is not doing command authorisation and accounting..
If any one know what I can append in so that it can show who executed the command.
thanks
AijazThe CLI command I'm trying to run is "copy runnning-config tftp", but I don't know how to pass variable on the ASA. I know some Cisco IOS you can create environment variable for the EEM to use. The command I'm trying to run requires user input such as: the source file, destination tftp client and the destination file. How to pass that? Or maybe what command can I run to save the config to a remote server?
thanks, -
Configuration Changes logging issue, ASDM related?
I've run into an interesting problem.
ASA: 8.4(2)
ASDM: 6.4(5)
When I make a change at the CLI, syslog message ASA-5-111008 is generated and sent to the syslog servers, local buffer, and ASDM.
When I make a change in ASDM, syslog message ASA-5-111008 is generated and sent to the local buffer and ASDM. It is NOT sent to the syslog server.
Here's my logging config...
Firewall# sh run logging
logging enable
logging timestamp
logging standby
logging buffer-size 409600
logging buffered informational
logging trap notifications
logging asdm notifications
logging host Inside xx.xx.xx.AA 6/1468
logging host Inside xx.xx.xx.BB 6/1468
logging flash-minimum-free 10240
logging flash-maximum-allocation 10240
logging permit-hostdown
Surely I'm missing something obvious. Is this a known bug?
Thanks!Ha, I did upgrade just a few minutes ago, but same result.
That does look similar, and so does ...
CSCth14248 ASA not sending all logging messages via TCP logging
Looks like I'll need to upgrade to 8.4(3) to fix these and see how it goes.
thanks! -
Firefighter Config change logs / SOD logs are not displayed..
We are on GRC 5.3, SP8. I have configured the SUP and firefighter id's are working fine. However, I am getting the message " No match nor conflict found " when I execute the 'Configuration Change Log report' and 'SOD Violations Report' even though the we changed the configuration and FF id's executed conflicting transactions defined in RAR. ' Log data changes ' box is already activated in the following tables:
1. Configuration (/VIRSA/ZFFCONFIG)
2. Controllers (/VIRSA/ZFFCNTRL)
3. Critical Tcodes (/VIRSA/ZVIRTCODE)
4. Firefighters (/VIRSA/ZFFUSERS)
5. Owners (/VIRSA/ZVIRFFIDS)
6. Reason Codes (/VIRSA/ZFFRCD)
7. Security (/VIRSA/ZVIRFFPWD)
Still the logs are not displayed. Thanks for your help.
Regards,
RajHi Raj,
Can you check the SM37 background job../VIRSA/ZVFATBAK is running or NOT???
Regards'
Gangadhar -
Is there any way to download/print/export the CUP Change Log?
Does anyone know if there is a way to export, download, print, etc. the CUP Change Log report? We are on GRC 5.3 SP13.
We have just started an audit review and the Auditors are asking for a report of all changes made since 10/1/2010. I can generate it on the Configuration/Change Log/Search Change Log screen but it doesn't seem to have any export/print options.
If this is not possible, does anyone know what tables make up the Change Log? I may be able to give them a report off of the tables.
Thanks.Hi Bob,
by default there is no export feature for that one.
To find the right table I only see that you would need to query the tables for one of the entries to find the right one as there is no official DB structure published.
Best,
Frank -
Logging CRS configuration changes
Hallo,
in a 10.1 RAC environment,
is there a file which logs CRS configuration changes, like issuing a oifcfg -setif command?
ThxYes
-
Log configuration changes to syslog on Nexus 7000?
I need to be able to log any configuration changes to syslog on our Nexus switches. On IOS this is easy with the archive commands, but I'm a little stuck trying to do this on our Nexus gear. On the IOS gear I run the commands:
archive
log config
logging enable
logging size 100
hidekeys
notify syslog
How do I do the equivalent on NX-OS?Cisco NX-OS can log configuration change events along with the individual changes when AAA command accounting is enabled.
With command accounting enabled, all CLI commands entered, including configuration commands, are logged to the configured AAA server. Using this information, a forensic trail for configuration change events along with the individual commands entered for those changes can be recorded and reviewed.
Because of this capability, it is strongly advised that AAA command accounting be enabled and configured.
Refer to the “TACACS+ Command Accounting” section of this document for more information.
The Nexus 7000, by default keeps a local accounting log of all the configuration commands entered on the device; you can view this with the 'show accounting log' command.
In NX-OS, we changed the way logging works. We keep a local accounting log of all the
configuration changes ("show accounting log"), but if you want to send those logs to a
server, it must be done with through a TACACS server. Please see the below documentation:
Configuring AAA on Nexus
TACACS command accounting
-Thanks
Vinod
**Encourage Contributors. RATE Them.** -
Can the ACE be configured for logging configuration changes to syslog server ?
Hi,
On all our routers, switches and firewalls we've configured syslog so we get logs when configuration changes occur.
Is this possible on the ACE too ?
regards,
SebastianHi Sebastian,
Yes it is possible but depends upong the logging level you have set. So logging trap 5 should be able to get you the configuration changes or command execution logs.
Nov 1 2013 11:20:33 : %ACE-5-111008: User 'admin' executed the 'logging buffered 6' command.
Nov 1 2013 11:20:48 : %ACE-5-111008: User 'admin' executed the 'no rserver testlog' command.
So you should see these level 5 logs on syslog if logging trap 5 is configured.
Let me know if you have any questions.
Regards,
Kanwal -
Configure the Change Log for the activity
Hi to all,
I would like to know if it is possible to configure the "change log" for the activity.
Thanks in advanced,
MatteCarlos,
Can you be more specific on the term 'Configure'. Change log is automatically generated by SBO. The only thing you can change is the numbers of Historical instances of the log
Administration > System Initialization > General Settings.......Services Tab...History or Log Settings. Be default it is 99 instances.
Suda -
Vendor Classification Change Log Activate : Configuration Change
Hi,
I want to know what is the process of activate Change Log for the Vendor Classification. Please suggest.
RgdsYou can see in Xk02 / Xk03 transaction - Environment tab - Field changes..
-
Hi Friends,
Please help me in finding the change logs for the TCODE FILE,
i.e The changes made to the Logical paths
I had tried Utilities---->change logs , but unfortunately i cannot find any changes logs
But there are changes made to the logical paths in my system but i cannot see them in change logs
thanks
chandrasekhar jrec/client is a profile parameter, you can view the settings in transaction RZ10. However I find program RSPARAM more useful, the report lists all system parameters with their default and altered value. Also if you double-click on a parameter you can get to the full help text for its meaning.
The parameter essentially switches on table change logging for configuration tables (based on the technical settings of the table) and has to be set before the changes are made.
Hope this helps.
Nick -
Configuration of logging severity
Hello everyone,
I am trying to use the weblogic Admin console to modify the logging severity at runtime. I have an application deployed on the AdminServer.
In the web console, I go to the AdminServer Settings page and navigate to the Logging tab. I click the "Advanced" link to show the "Logger severity properties". In this box I have tried entering many different values. I save. There is no change to the logs. I restart the server, there is still no change to the logs.
Some values I've attempted to use:
com.mycompany.level=Trace
com.mycompany.level=Debug
com.mycompany=Trace
com.mycompany=Debug
.level=Trace
.level=Debug
I am using weblogic 10.3.2.0 with jdk logging.
Does anyone know if these configuration changes are supposed to affect the log files? Am I using this configuration parameter incorrectly?
Note that I have found a way to configure the logging severity using a logging.properties file, by calling:
LogManager.getLogManager().readConfiguration(EventDAOEJBImpl.class.getResourceAsStream("/logging.properties"));
However, this does not allow me to configure the application from the weblogic console. Is there a way to configure the logging severity using the weblogic console?You may want to ask in the WebLogic Server - Diagnostics / WLDF / SNMP forum. They own logging.
I asked them to reply to this message. -
How to see the change logs for billing document
Dears,
Could you please how to see the change logs for billing document.
My client is using ECC 6.0 & if i use VF03 > Environment > changes > does not show the changes i had made.
Thanks in advance
Ranjanhello, friend.
you should be able to see changes done after the initial creation and saving, by going thru Environment > Changes. try it again, and this time make sure that changes were done to the billing document prior to posting to accounting.
normally, when configuration of Billing is done correctly, there will be little or no instances of changing anything in the Billing document, as saving the document after creation will post this to Accounting. of course, inclusion of a posting block in the billing type will provide you the opportunity for changes.
regards. -
Change log report S_AHR_61016380 not picking IT0025
Hi Experts,
I need the change log report to capture the details of changes made in IT0025 (Appraisals).
I have made necessary configurations to the below tables by watching in other SDN threads, but still my problem is not solved.
Also made changes to master data (IT0025) and tested, but still no use.
Log report is not picking changes made to IT0025.
Please suggest
Thanks
VenkateshDear Expert,
for logged changes in infotype report we need to install crystal report.
please suggest.
Maybe you are looking for
-
Slow performance since installing Mavericks
Our Mac is used by four seperate users with their own log in's. Since installation of Mavericks the performance for two of the users has slowed dramatically to where they get "beachball" for minutes at a time. The other two users don't experience an
-
ITunes doesn't recognize iPod mini
We bought a new computer and the old iPod is not being recognized by iTunes. The iPod displays "Do not disconnect", but iTunes is not updating it. I downloaded the most recent iTunes version. There are no iPod files in the application data folder for
-
Three Monitor Save, Two Monitor Hang- CS6
I have three monitors running from my Dell M6600 at work. I save a Premiere Project with any panel open on the third monitor. Then take my computer home where I only have two monitors and open the project file, Premiere hangs. It will never launch
-
Creating website and changing computers
Alright, I am new to website creation and look forward to using iWeb. Here is my question: Currently I have iWeb on a Powerbook G4. Eventually I intend to buy a MacBook Pro. If I create a website on my Powerbook, will I encounter problems with access
-
Connecting only wanted points in analysing xy graph
hello NI thanks in advance for the team support firstly i am getting a force velocity characteristic on an xy plot and from this graph iam geeting peaks plots on another graph. Now problem is i want to store only these peaks points in an file anothe