Configuration changes via browser not written to startup

I have recently discoverd that some changes applied via a browser interface are not applied to the startup configuration. I confirm this by starting a telnet session to the device and entering show start. This appears to be inconsistant in that sometimes I see the change from sh start and other times I do not.
Im using IOS release
c1200-k9w7-tar.123-2.JA

Update -
Discoverd that when I telnet to a device and try to copy running configuration to startup configuration, I recive the following error message.
apmp12001e#copy run start
Destination filename [startup-config]?
Building configuration...
Error writing new config file "flash:/config.txt.new"
nv_done: unable to open "flash:/config.txt.new"
Error writing new block-fs file "flash:/private-multiple-fs.new"[OK]

Similar Messages

SG 200-08 - configuration changes disappear on power cycling

it's my first smart switch, but i've set up a million routers, so i'm not a complete n00b.
the only change that survived power cycling is the change of default password that it forced me to do.
what am i doing wrong, or is the box defect?

You will need to save your configuration changes before exiting the switch. Below are the steps to do this taken from the Admin guide.
THANKS
Rick Roe
Cisco Small Business Support Center
Copying and Saving Configuration FilesThe
Copy/Save Configuration page enables you to copy files within the filesystem. For example, you can copy the Backup Configuration file to the Startup
Configuration file so that it will be used the next time you boot up the switch.
To copy a file to the Startup or Backup Configuration file:
STEP 1
Click Administration > File Management > Copy/Save Configuration in thenavigation window.
STEP 2
Select the Source File Name:
Running Configuration
—Current configuration, including any changesapplied in the current management session.
Startup Configuration—Configuration file type used when the switch lastbooted. This does not include any configuration changes applied but not yet
saved to the switch.
Backup Configuration—Backup configuration file type saved on the switch.
Mirror Configuration—If the Running Configuration is not modified for atleast 24 hours, it is automatically saved to the Mirror Configuration file type,
and a log message with severity level
Alert is generated to indicate that anew Mirror Configuration file is available. The Mirror Configuration file can be
used when the switch has problems booting with the Startup or Backup
Configuration file types. In such cases, the administrator can copy the Mirror
Configuration to either the Startup or Backup Configuration file type and
reboot.
STEP 3
For the Destination File Name, select the file type to be overwritten with the file
you are copying:•
Startup Configuration—Configuration file type used when the switch lastbooted. This does not include any configuration changes applied but not yet
saved to the switch.
Backup Configuration—Backup configuration file type saved on the switch.
STEP 4
Click Apply to begin the copy process.When complete, a window displays the message, Copy Operation Successful.

Portal not accessable via browser as inside sapmmc - http provider is red

Hi Experts,
I am very new to NW admin side and currently my client is facing an issue while accessing portal via browser.
Problem: Some times suddently when users try to access production portal it takes a lot of time to open up and in most cases it doesn' t get opened up at all. To check what' s wrong with the portal i access sapmmc and inside their i find under current status -> ... -> services -> http provider -> total requests in red status with a description as avg request - response time last reported value above threshold limit. It will be the same case under open alerts too.
My server configuration is:
SAP-JEE = 7.0SP14
OS = Windows 2003 (X86) 5.2
Server Version = 1.4.2_17-bo6
Kernel Version = 7.00 patch level 109886.44
Server = 32 bit
RAM = 16.00GB
Processor = Intel(R) Xeon(R) CPU E5450 @3.00GHZ (8CPUs)
Heap Size: 1024 MB
Approximate number of users = 500 - 600
Currently to solve the issue, we give a reboot to server. But with the progress in time the frequency is getting increased drastically (approx once in 2- 3 days).
Any pointers on how to solve this issue will be greatly appreciated.
Thanks In Advance,
Vipin.

Hi all,
Thanks for your valuable inputs!
Now the issue seems to end up by raising an OSS notes with SAP and i have been given responsibility to prepare a doc that needs to be submited to SAP.
I have already got the screenshots from SAPMMC on it' s status and all, but also requires log information specific to the reason behind this behaviour. Can i know where the log information specific to such issues gets logged and all the necessary information that i need to document to raise an OSS.
Inputs with be of great help and will be highly appreciated.
Thanks In Advance,
Vipin.

Cluster startup parameter configuration change.

Hi All,
Could you please suggest steps to change SQL startup parameter in windows server 2008. I'm having patrol agent service configured in order to monitor the SQL instance, But due to mis-configuration patrol instance startup parameter is wrongly configued in
windows cluster. I am not quite sure..how to go on to sort it out.
Please suggest do i need to take downtime as well.

We are going to have to have a fair bit more information, as your problem statement does not make much sense. And, if you are asking specifics about SQL, it is better to ask questions in a SQL forum. There is actually a SQL forum dedicated to
high availability.
In either case, though, you will need to clarify what you mean. What makes you think you need to change the SQL start up parameters? You seem to be indicating issues with configuring a 'patrol agent', whatever that is. Maybe the vendor
can help you get that right. Are you sure that your issues are not around the 'patrol agent' and not around SQL startup parameters? Since we really don't know what you are trying to do, we don't know if it will cause downtime or not.
. : | : . : | : . tim

My new users can not upload files via browse

Hi there;
When my recent created users can not download files via the browse within the Internet interface.
When I hit the via browse I face the following:
500 Internal Server Error
oracle.ifs.common.IfsException: IFS-10406: Invalid AttributeValue conversion (DIRECTORYOBJECT to Java DirectoryObject)
oracle.ifs.common.IfsException: IFS-10200: Unable to access object (insufficient privileges)
Any hint?
Sasan Ebadian

Hi Sasan,
These are the ACL's of IFS:
PRIVATE Grants no permissions to any other user. Other users cannot view, modify, or delete a user’s document in any way, unless changed by the owner.
PROTECTED For folders only. Enables other users to see the files in the folder, add documents and folders to the folder, and remove documents and folders they have created from the folder, but are not allowed to delete the folder itself.
PUBLIC Allows full access to the item. All users can make any changes that the owner can make.
PUBLISHED Allows other users to view the contents, but they are not allowed to modify or delete the document.
If you attach the ACL Public it must work!
Bob

Not Able to Use Gtalk in Curve 9320 Via my Sim data but internet is working as i checked via browser

Hello,
Not Able to Use Gtalk in Curve 9320 Via my Sim data but internet is working as i checked via browser & i also use youtube but not able to login any messaging option & not able to creat Email account Please Help!
Thanku
Shivam

Hey shivamr25,
Thanks for the reply.
After checking your PIN number, it shows you do not have a BlackBerry® data plan with your network service provider. This is required to use Google® Talk. Contact your network service provider to add a plan.
Let me know if you have any more questions.
Cheers.
-ViciousFerret
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Like! for those who have helped you.
Click Accept as Solution for posts that have solved your issue(s)!

Changed value in Appent not written to change document

Hello,
I have added some fields to a table using an append. During test I realized that the function that creates the change document does not consider appended fields (I debugged deep into some SAP function to see why). This is a problem now. All changed values must be written into the change document. Did anybody have the same problem? Any ideas how to solve this?
Thanks, Oliver Plohmann

Hi,
For the customer data element check the Change document check box is selected or not. It should be selected then only the changes captured
Se11 - > Data type - > enter Data element name
In the Attributes tick the check box Change document.
Hope this will work
Cheers,
Sasi

Since I changed the operating system Windows 7 32bit to 64bit I can not use Firefox browser unless change the browser to safe mode.

Since I changed the operating system Windows 7 32bit to 64bit I can not use Firefox browser unless change the browser to safe mode.When i start it the browser is not open and appears a message
Mozilla Crash Reporter
== Crash ID(s) ==
20100611143157
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; .NET4.0C; .NET4.0E; InfoPath.3)

the 20100611143157 is an update which won't instal automatically on my notebook

My Logitech bluetooth laser travel mouse does not connect at startup to my recently upgraded iMac. Even when this is configured. I need to configure the mouse everytime after startup!!

My Logitech bluetooth laser travel mouse does not connect at startup to my recently upgraded iMac. Even when this is configured. I need to configure the mouse everytime after startup!!... It worked fine with previous OS X .... How can I fix this??

My Logitech bluetooth laser travel mouse does not connect at startup to my recently upgraded iMac. Even when this is configured. I need to configure the mouse everytime after startup!!... It worked fine with previous OS X .... How can I fix this??

Smart Collection for images with changed metadata not written to disk?

The thumbnails in the grid view have a little icon in the upper right corner when the metadata for the file has been changed but not written to the XMP (or whatever) files.
Is it possible to create a LR2 Smart Collection, or maybe a filter, that will find all such images?

Dave, good to know that Ctrl-S on everything will write it all out.
John, I *hate* being blind about what is going on. So I can Ctrl-S on everything and get it all written out. But I can't tell how many images I have changed, or perhaps also sort them by type so I can see what kinds of files will have to be rewritten. I can't even tell if I've remembered to do a Ctrl-S and whether there are images with data only in the catalog and not in the XMP etc. files.
I'm one of those who are more comfortable if everything that can be recorded in XMP is recorded there. But I don't want to leave auto-write to XMP on while re-organizing everything.

CF 7 cluster does not respond to configuration changes

I am evaluating the clustering capabilities of CF 7 in order
to upgrade our current CF6 + ClusterCats cluster.
I installed CF7 (enterprise edition – multiserver) in
two physical servers (Win 2003). On each server I created one
instance of CF and successfully registered the remote instance on
each server. Then, I configured the cluster on the first server,
selecting the weighted random algorithm for load balance and
session replication. Then, I used the webserver configuration tool
to bind the cluster to each IIS server.
The cluster worked properly, balancing the load between the
two cf instances, but when trying to find a way to temporally
restrict the load on one server for maintenance purposes I found
that the cluster does not respond to cluster configuration changes.
I changed the load to 0-100% using the coldfusion administrator
interface but it did not work. The cluster still sends requests to
the “restricted” instance. I even eliminated that
instance from the list of instances that integrates the cluster,
but it did not affect the behavior of the cluster. The eliminated
instance still serves request from the cluster. I even eliminated
the remote instance register and nothing… the cluster still
balancing the load between the two instances that originally
integrated the cluster.
I do not understand how this is supposed to work. Does the
cluster configuration interface works only when creating the
cluster? When the changes in the cluster configuration performed
from the CF admin interface should be reflected by the behavior of
the cluster? What is the recommended procedure to temporally
restrict one instance from the cluster without stopping the
service?
I appreciate your help
Eduardo

Thanks for the information Jochem. I am afraid that these are
not good news. If I have to restart the webserver in order to
change the load balance, some requests in progress could be lost.
My current configuration is composed by two physical severs,
each one running a web server and a coldfusion instance. We balance
the load between both webservers using hardware load balancing.
This is the procedure that I have to follow in order restrict one
instance without loosing any request:
1.- Change server weight using Coldfusion admin interface
2.- Configure hardware load balance to restrict server 1
3.- Restart webserver at server 1
4.- Configure hardware load balance to enable server 1 and
restrict server 2
5.- Restart webserver at server 2
6.- Configure hardware load balance to enable server 2
A similar procedure should be followed in order to enable the
restricted instance. I know that I can do it for 2 servers; but,
how is it handled in larger clusters? Is there a better procedure
to restrict one instance without missing requests?
Eduardo

I have Photoshop CS purchased many years ago for a LOT of money. Other day went to use it, got msg. "computer configuration changed, need to re-activate". Tried that for days, didn't work. Cannot call ANYONE to find out problem. Am not very computer l

I have Photoshop CS, purchased many years ago for a LOT of money. Other day went to use it, got msg. "computer configuration changed, need to re-activate. Tried that for days, didn't work. Cannot call ANYONE to find out problem. Am not very computer literate, so don't understand what that means. LOVE the CS program and know how to use it, so don't want to have to learn something new. Don't know what to do. Went to all the big name stores and no one can tell me anything, like what happened to CS or what is replacing it that is the same as CS. CAN SOMEONE PLEASE HELP!!!

jd49034389 wrote:
down further there is a Photoshop CS2, do I just do that one?
Yep. That's the one. Make sure to use the supplied key on the download page, not your old one.
Good luck.
--OB

I changed my browser fill and the update does not show in the preview mode

I changed my browser fill and the update does not show in the preview mode. I saved and restarted muse but the problem is still there. Any thing else I can do? Could it be something that changed in the file?

Hello,
What did you put in the "browser fill" area, an image or a color? WIth gradient or with solid color? Also, does it show fine if you "Preview in Browser"?
Screenshots showing the Browser fill section (like this: http://screencast.com/t/RHqdVPP4) and the display in Preview mode would also be helpful.
Cheers
Parikshit

Firefighter Configuration - FF Owner should not change the configuration

Hello Experts,
We have requirement to restrict Firefighter configuration changes only to Firefighter Administrators.
1. Restricting Firefighters to make any changes in Firefighter Configuration -- SAP Note 1101665 Superuser Security Role Modifies Tables - Successfully Achieved.
2. Restricting Firefighter ID Owners (having /VIRSA/Z_VFAT_ID_OWNER) to make any changes in Firefighter Configuration --> Need your inputs on how to achieve this.
We want that Firefighter ID Owners can only assign the FFID to Firefighters and assign a new controller only, but no following should be allowed to Firefighter Owners -->
a. Creating a new owner for a FFID.
b. Changing Firefighter configuration.
c. Creating or changing Reason Codes.
And which role should be assigned to Firefighter ID Controller?
Looking forward to hear from your experiences.
Thanks & Regards
Davinderpal Singh

Thanks Alpesh and Simon for your valuable inputs.
My observations are, if you assign Firefighter Owner and Controller role only, then user is not able to make any configuration change, Reason Code change, etc, etc - behaviour is as expected.
And in our case, this problem is coming as FF owners/controllers have been assignbed few other roles/profiles which seems to override the authorisations of FF owner role and allow changes in FF configuration.
Now searching through each of these roles/profiles for extra set of authorisation objects is a huge security job.
And we don't have much experience in Security - so as per your experiences what should be the best way to restrict FF owners to not make any change in FF configurations, without removing existing roles/profiles ( as we don't know what all would be removed if we remove all of these roles).
Is it possible to specify a condition/check so that if a user has been assigned FF owner role, inspite of whatever extra permission he has - he should not be able to make configuration changes - please bear with me if i am expecting too much over here.
Which authorisation objects controls FF configurations changes?
Best Regards
Davinderpal Singh

I'm in Afghanistan with limited internet options. I have a wifi service plan I am signed up for however, a log in and password are required via browser log in, not a security key attached to the wifi. Please help...

I'm in Afghanistan with limited internet options. I have a wifi service plan I am signed up for however, a log in and password are required via browser log in, not a security key attached to the wifi (like a hotel). Please help...

the appletv will not be able to work on it's own
you can use a computer or iphone acting the role of hotspot login using it's browser and getting internet access and then sharing it with the appletv
so the appletv sees it as a wifi router it connects to

Configuration changes via browser not written to startup

Similar Messages

Maybe you are looking for