Configuration file for smart view for Hyperion planning

Hi,
We are using SmartView for accessing HyperionPlanning application. Please let me know how can we change the provider to use shared services and enable planning it for logging to file. Also which properties file is used for these configurations and where can we locate the configuration file on Hyperion planning installation system.
Please suggest.
Thanks
Edited by: user11189447 on Aug 12, 2010 8:17 AM

Hi,
Checkout the below metalink from Oracle.
Hyperion Strategic Finance Will Not Connect Via SmartView (Doc ID 1561484.1)
Below Solution as per doc ---
1. Run the installation for the HSF Web Application component on the Foundation server where weblogic is for HSF Server.
(Be sure the HSF Web Application component is also installed on the the HSF Server, if separate from the Foundation server as well.)
2. Clean up any failed deployments in the WebLogic Console by deleting the HSFWeb Server from WL Admn
3. Configure the new component on Foundation (target server).
4. On OHS server run configtool and perform the WebServer config task to configure OHS for HSFweb
5. Restart OHS and start HSFWeb
Thanks,
~KKT~

Similar Messages

Language Setting for - Hyperion Smart View for Office

Hi,
Here's a scenario I need to find an answer to.
1. We have Essbase system 9 installed on a machine named: USESSSRVR and here the ESSLANG environment variable is set to "English_UnitedStates.US-ASCII@Binary".
2. We build two Unicode cubes, one for Korea Sales called APPKR.SALESCUB & other for Turkey Sales called APPTR.SALESCUB
3. Korean users are sitting in Korea & Turkey users are in Turkey & both these users need to see data in their local languages.
4. Since Essbase Excel Add-In is not compatible with Unicode cubes, we have asked them to use "Hyperion Smart View for Office".
Now question is,
-> Where in this entire system do I need to do Language Settings so that they see their characters correctly?
-> Is there a place in Smart View where you can set languages?
-> Also we have a limitation that we need to have both the applications APPKR & APPTR on the same Essbase server which is in US.
PLEASE HELP.
Thanks.
~Jaymin Darbari.

It's actually because you are installing over an old version. Uninstall SV, review the registry entries and directories and then reinstall with admin priv.
Of course when I looked it up on support the Oracle ID 1466433.1 suggests that the .net install is corrupt so was i going mad? Not beyond reasonable doubt since I put in an SR a while back about it so I have proof that it is listed as an " "internal bug #14149839 : "SMART VIEW EXTENSION ACTIVATOR OBJECT (-2147467262) This is reported for excel 2010" has been raised with development team. As per the update from the bug this issue has been addressed in patch 11.1.2.2.310 which is yet to be released."
So if you are on an earlier version of Office possibly is because of the .net install (which I think needs v3.5, at least for Office2003), but I would try do a clean install first.
Steve

IW21 Classification screen structurre for extended view for a notification type

Hi Guru's,
In Spro I added a screen structurre for extended view for a notification type
I have well the subscreen now but the labels are missing and the button classification doesn't work.
I guess that I should implement an user-exit or a badi.
Any idea please ?
Regards,
Rahhaoui

See this picture This is from the same thread I referred earlier. I feel there should be better ways of learning these fundamentals about Module-pool programming, rahhaoui !
Best of luck
Jogeswara Rao K

Smart View for Essbase Not Available in Planning Rapid Deployment

I have successfully deployed EPM 11.1.2.3 by following the steps in the Planning Rapid Deployment guide (http://docs.oracle.com/cd/E40248_01/epm.1112/epm_planning_rapid_deploy/epm_planning_rapid_deploy.html). However, when I bring up Smart View using a Shared Connections URL of http://<servername>:9000/workspace/SmartViewProviders, I only get connections for Planning and for the Reporting and Analysis Framework. How can a I get a connection for Essbase?

As it turns out, the 11.1.2.3 Planning Rapid Deployment wizard doesn't install Essbase Provider Services, just Planning Provider Services and Reporting and Analysis Provider Services. Until I installed Essbase Provider Services, I wasn't even able to create a private connection to Essbase. I had to run InstallTool.cmd and select "Provider Services Web Application" from the Essbase section of the selection screen. I also had to run the configuration utility and select "Deploy to Application Server" under "Provider Services" in the Essbase section of the selection screen.
After that, I was able to create a private connection to Essbase with this URL: http://<server name>:9000/aps/APS
Although the private connection was now working, the Essbase connection was still not showing up as a shared connection in Excel, when I set the Excel Smart View option for Shared Connections URL to http://<server name>:9000/workspace/SmartViewProviders. I was able to get this working by running the configuration utility again and selecting "Configure Web Server" in the "Hyperion Foundation" section of the selection screen.
I was also able to create an XML file as Celvin suggested, using http://<server name>:9000/aps/APS for the Essbase connection. Thanks for the suggestion!
-Tom

Hyperion Smart View for MS Office doc.

I am using Hyperion System 9 IR on PC version and connected to a Oracle DB 10g. How can I create the shared service for the Samrt View in this case ?

It's actually because you are installing over an old version. Uninstall SV, review the registry entries and directories and then reinstall with admin priv.
Of course when I looked it up on support the Oracle ID 1466433.1 suggests that the .net install is corrupt so was i going mad? Not beyond reasonable doubt since I put in an SR a while back about it so I have proof that it is listed as an " "internal bug #14149839 : "SMART VIEW EXTENSION ACTIVATOR OBJECT (-2147467262) This is reported for excel 2010" has been raised with development team. As per the update from the bug this issue has been addressed in patch 11.1.2.2.310 which is yet to be released."
So if you are on an earlier version of Office possibly is because of the .net install (which I think needs v3.5, at least for Office2003), but I would try do a clean install first.
Steve

Issue with Smart View for Planning Connection

Hi All,
I'm facing this issue with Hyperion 11.1.1.3 & 11.1.2. I've created a connection in SmartView by giving the URL as http://ServerName:8300/HyperionPlanning/SmartView. After that i'm able to see "Servers" and when i started expanding that, it displayed the server name. When i clicked on the server name, it should display the Planning Application name right ? instead of that just a Cuble symbol is displaying. Do i need to make any settings for proper display of the Planning Application names ? This is perfectly working fine with HFM. I'm able to see HFM application names

Well, the thing I always forget and have pulled much hair out over is to add the essbase server access to the planning group.
Check on that, and I will loosen the rocks in my head to see what else I can suggest.
Robb

How to lock data independently for several groups in Hyperion Planning?

I 'm developing a forecast application using Hyperion Planning 9.3.1 where the users shall be able to enter their monthly forecast numbers. We have two groups of users. Each group may have up to two forecast updates per month. The groups are independent – say, Group A may have one update for August and they want the numbers to be there by August 10th, while the Group B may have two updates for the same month with the first update to be completed by July 20th and second – by August 5th. Nobody knows in advance how many updates they are going to have for the month and when they are going to have them. Nothing should prohibit the users from updating their forecast numbers for the future months – say, they may enter their September forecast in July.
Managers of both groups want to make sure that users don't change forecast numbers after the month close. If they plan to have two updates per month – they want data from the 1st update to be locked (become read-only) before they have 2nd update, and data from 2nd update locked after the month close; if they plan to have only one update per month – they want it locked after the month close.
Any suggestions how I may structure the dimensions of this application to make sure that if I lock first August update for Group B on, say, August 3rd, the other group still can have it open until August 10th?
Thanks!

Hi John
Well i have working knowledge in ODI, i did whole complete cycle and i did customization project for Oracle EBS to Data warehouse though ODI.
What, I am NOT able to figure out How to LINK Hyperion Planning Outline to Oracle EBS HR Tables. cause in Hyperion Outline i m able to view Dimensions Not particular Column to map with EBS HR Table (column).
Eample:
In EBS HR we have Employee Number in Per_all_people_f but in Hyperion Planning Dimension is ONLY Employee.
Your response highly appreciated.
Chreeez
Sher

Pre-requisites for Drill-Down from Hyperion Planning to Oracle GL

I am using Hyperion Planning 11.1.2 for maintaining budgets. I do comparison of actual vs budget in Hyperion. I export actual results from Oracle General Ledger (11.5.10) in flat file and upload to Hyperion planning using FDM. I maintain mapping in FDM for flat file and the Hyperion members.
Q1) Is it possible to drill down actual numbers from Hyperion planning to Oracle General Ledger via FDM?
Q2) If yes, what are prerequisites for using drill-down functionality?
Can anyone please answer and refer some link/material that may help me in setting this up?
Thanks in advance.

Thanks
But when i try to log in i m getting error bellow"
Failure of server APACHE bridge: No backend server available for connection: timed out after 10 seconds or idempotent set to OFF."
So do u have any other reference plz
thanks

Unable to configure file adapter using FCC for Multilevel hierarchy

Hi Experts,
Can anyone help me in configuring the Receiver file adapter with FCC for the structure given below
<Root>
<Level1>
     <Ele1>
     <Ele2>
     <Level2>
            <Ele2_1>
            <Ele2_2>
            <Level2a>
                    <Ele2a_1>
                    <Ele2a_2>
            </Level2a>
     </Level2>
</Level1>

Hi dineshmale,
I have do this Multilevel hierarchy before. FCC can directly configure this scenario. But I don't know you output format. What my format shown below(here i use '#' instead of space):
Level1_Field1##Level1_Field2##Level1_Field3##Level2_Field1##Level2_Field2##Level3_Field1##Level1_Field2
#################################################################Level3_Field1##Level1_Field2
#######################################Level2_Field1##Level2_Field2##Level3_Field1##Level1_Field2
#################################################################Level3_Field1##Level1_Field2
Level1_Field1##Level1_Field2##Level1_Field3##Level2_Field1##Level2_Field2##Level3_Field1##Level1_Field2
#################################################################Level3_Field1##Level1_Field2
#######################################Level2_Field1##Level2_Field2##Level3_Field1##Level1_Field2
#################################################################Level3_Field1##Level1_Field2
#################################################################Level3_Field1##Level1_Field2
FCC Parameter:
Recordset Structure: Level1,Level2,Level3
Level1.fieldSeparator = (2 spaces)
Level2.beginSeparator = (some spaces according to the length of the fields in Level1)
Level2.fieldSeparator = (2 spaces)
Level3.beginSeparator = (some spaces according to the length of the fields in Level1and Level2)
Level3.fieldSeparator = (2 spaces)
Level3.endSeparator = \n
There are some points:
1. the endSeparator for Level1 and Level2 doesn't work.
2. the first begin separator in Level2 and Level3 doesn't work.
3. The last field of super node and the first field of child node is separated by the (child).fieldSeparator.
4. ....
What's more, I have write a blog of FCC For Hierarchical Structure in Receiver Channel just now. So it need two days for Approval. Let me know for any issues.
Edited by: guKidd on Dec 14, 2010 7:52 AM
Edited by: guKidd on Dec 14, 2010 7:54 AM

How to create bulk configuration files from a template for staging?

Hello,
We have created a sample configuration for ISRG2 2901 Router. The sample configuration is long, and with copy/paste it is possible to skip some lines, and it is difficult to ensure the configuration of every device is standardized due to this error possibility. What we are trying to achieve is first create a template from this sample configuration file, and then create configuration files for each device seperately and automatically. After creating this configuration instances, we want to be able to distribute the configuration files (and possibly the ios) to the devices during the staging phase. Since there are about 1000 2901 routers, creating configuration files is important?
From searching we have found the following tools:
1) CCE (Cisco Configuration Engine): This tool seems to be very efficient for distributing the created configuration files. We may use the serial number of the device, and it provides almost zero touch provisioning of the configuration files to the devices. Creating the configuration file from the template seems to be manual, i.e enter the ip addresses of the interfaces, the routing tables one by one for each device. How can we use velocity template for device configs?
2) Ciscoworks LMS Prime: It is possible to create a baseline template for the devices, and after getting the backup configuration of the routers, it is possible to compare the actual configuration of the device with the baseline template, and understand if there is any difference with each other. This is indeed very useful in order to keep the configuration standardized, we again could not find a way to create bulk configuration files from the baseline template.
3) Solarwinds Config Generator: This tool is useful for creating a configuration file from a template, but again not for automatically creating configuration files, and needs manual intervention.
4) Excel Macro: It seems that some people have achived to automatically create configuration files with using an excel macro, but we could not find a procedure or tip of how to achieving this.
5) Pearl or TCL/TK Script: Again since we are not software developers but from networking field, it is difficult to achieve a working form of this scripts or codes due to to lack of documentation and development experience.
So our problem comes down to creating a template from a sample configuration, and creating bulk configuration files from the template. Is there a specific tool or procedure to achive this purpose?
Thanks in Advance,
Best Regards,

Hi,
Try this one http://www.gen-it.net
Regards,
Stuart

Setting up Balance Account for Balance Sheet in Hyperion Planning

We are using version 11.1.2.1.0.83 of Hyperion Planning. What is the best way to setup a balancing account for the balance sheet? Should it be store, or dynamic calc? Should a Member formula be used or should it be done via a calc script? What would the member formula look like?

Hmm, I give you the answer, you mark it as answered but don't give me any points, and now you ask another question? I only do this for the points. <grin>
I am still curious as to whether this can be accomplished by embedding a member formula in the balancing account and, if so, what the embeded formula script might look like. ^^^The formulas I illustrated and you implemented could be put into a dynamically calculated member. So long as the account to be balanced is first (I am thinking calculation order) the dynamic calc should be just fine. I've used that approach in Planning apps in the past.
Regards,
Cameron Lackpour

"Marked for Delete" flag in Hyperion Planning

Does anybody know how can I set "Marked for Delete" value by ODI? I have reversed planning model by RKM, but it hasn't field "Marked for Delete".
Thanks a lot in advance

user11340418 wrote:
Hi John,
In that case, what is the best practice for deleting a Hyperion Planning shared member.
I have to delete a shared member manually from Planning front end.
Is there a better way for deleting planning members?
Cheers,
RSHi, the Marked for Delete is nothing to do with deleting shared member.
You can can delete members by using the Operation column and it set to Delete, you will have to provide the member to delete and the storage type of Stored.
Cheers
John
http://john-goodwin.blogspot.com/

Improved Metadata Storage option for Smart View

I have looked all through the manuals, but I cannot find any reference to the "Improved Metadata Storage" Smart View Option. Does anyone know what this option does and the Pros/Cons of using it?

Thank you for responding. I would like to resume having the "Save as PDF" option but the IE8 Browser is an older version and is unfortunately running slower and not well on some of the websites that need newer Browser versions. I checked out Chrome and don't like Firefox and still prefer the IE Browsers by comparison.
Is it very difficult for HP to add this handy feature back in a future HP SmartPrint release that is compatible with the IE Browser?
Thanks!

Mostly what are issues we get for production support in hyperion planning project ?

mostly what are issues we get for production support in hyperion essbase project ?

When is the interview
Cheers
John

Smart view for obiee 11.1.16

hi
do we need any license to use the smart view in the company

Hi Srini
I did download the bi office on client machine but I am unable find the below path in my server
D:\FUSSION\user_projects\domains\bifoundation_domain\servers\AdminServer\tmp\_WL_user\bioffice_11.1.1\hsq62b\war\WEB-INF.
do we need to install it on server too to update the bioffice.xml
Thanks
Edited by: 990266 on Apr 25, 2013 1:12 PM
Edited by: 990266 on Apr 26, 2013 9:52 AM

Configuration file for smart view for Hyperion planning

Similar Messages

Maybe you are looking for