Configuration from Single Controller to Dual in SE 3510

Hi,
I have one Sun StorEdge 3510 with single controller. I am not trying to configure the controller with dual controller card. As soon as I insert second controller card I am not able to see the LUN from Solaris 10. Please advice what all changes I require to do while configuring from Single Controller to dual controller.
Thanks in Advance.
Best Regards,
Bikash

I dont think there is any difference in Callmanager software for a dual processor versus single processor server. For 7845 (dual processor) the hardware detection disks may be different from the one for single processor (7825, 7835)
Migrating from one to another is as easy as taking a BARS backup from one server, build the other server to the same version and restore it. (Make sure server name and ip are the same for both servers)
Please remember to rate posts!

Similar Messages

Rebuild our XI application server from Single stack to dual stack

Hello,
We currently have an XI landscape with two application servers, the CI is of course a dual stack system, however the two app servers are single stacked, however we would like to make the two app servers into DUAL STACKs, my first guess was to rebuild the two apps from scratch and reinstall them as a dual stack apps. My Q is:
First: Do we need to rebuild both app servers, or can we make a change to the app servers to modify them to become dual stacked
Second: If we do need to rebuild both these apps, is there a specific document available to do this on Market place for installing a Dual stack app servers with PI?
Thanks in advance.
Sam
<Moved from SAP PI Forum>
Edited by: Prateek Raj Srivastava on May 13, 2010 12:27 PM

Hello,
Thank you all for your feedback,
Denny Liao, it is very interesting question you implied, we do have a J2EE directory created under the /usr/sap/SID/D30 directory:
/usr/sap/XQ9/D30
mqaapz28:xq9adm 13% ls -ltr
total 36
drwxr-xr-x   7 xq9adm   sapsys        96 Aug 24 2009 igs
drwxr-xr-x   9 xq9adm   sapsys      1024 Aug 24 2009 j2ee
drwxr-xr-x   2 xq9adm   sapsys      1024 Nov 11 2009 sec
drwxr-xr-x   3 xq9adm   sapsys      1024 Nov 24 10:48 log
obviously this app server does not have any (jlaunch/jcontrol process running) therefore it is not running as dual stacked. but interestingly enough I do see logs in the
/usr/sap/XQ9/D30/j2ee/cluster/server0/log directory created at the time of the initial install. and under:
/usr/sap/XQ9/D30/j2ee/cluster
mqaapz28:xq9adm 29% ls -ltr
total 30
drwxr-xr-x   2 xq9adm   sapsys      1024 Aug 24 2009 bootstrap
-rw-rr   1 xq9adm   sapsys        39 Aug 24 2009 version.bin
-rw-rr   1 xq9adm   sapsys      6339 Aug 24 2009 instance.properties.vmprop
-rw-rr   1 xq9adm   sapsys      3676 Aug 26 2009 instance.properties
drwxr-xr-x   7 xq9adm   sapsys      1024 Aug 26 2009 dispatcher
drwxr-xr-x 11 xq9adm   sapsys      1024 Aug 26 2009 server0
as per the note you mentioned above (741289 ) this explains how to recover a lost J2EE parameter setup, I am guessing this can be simply followed and re-enable the app server to run as a dual stack.
also my system information for the J2EE on the CI is:
System XQ9
Find other systems in SLD... Message Server
Host: mcsapxq9j
Port: 3924
Enqueue Server
Host: mcsapxq9j
Port: 3224
Database
Name: XQ9
Host: mcsapxq9dbx
Type: Oracle (Oracle Database 10g Enterprise Edition Release 10.2.0.2.0 - 64bit Production With the Partitioning and Data Mining options)
Software Components all components...
Name Version Applied
sap.com/SAP-JEECOR 7.00 SP21 (1000.7.00.21.0.20091214121410) 20100506125119
sap.com/SAP-JEE 7.00 SP21 (1000.7.00.21.0.20091214121301) 20100506124943
Licenses
Installation Number *** not yet assigned ***
System Number *** not yet assigned ***
Software Product Days Until Expiry
Download system configuration
Instance mqacsz27_XQ9_30 All processes running
Host: mqacsz27
OS: SunOS (sparcv9) 5.10
dispatcher Running
VM system properties...
PID: 21384
Name: Java HotSpot(TM) 64-Bit Server VM
Vendor: Sun Microsystems Inc.
Version: 1.4.2_21-b03
VM Parameters
Cluster
Node ID: 301932700
Kernel Version: 7.00 PatchLevel 76340.450
HTTP Port: 53000
HTTPS Port: 53001
P4 Port: 53004
Telnet Port: 53008
Info for crashes of this node
server0 Running
VM system properties...
PID: 21394
Name: Java HotSpot(TM) 64-Bit Server VM
Vendor: Sun Microsystems Inc.
Version: 1.4.2_21-b03
VM Parameters
Cluster
Node ID: 301932750
Kernel Version: 7.00 PatchLevel 76340.450
Info for crashes of this node
SDM Running
VM
PID: 21400
SDM Port: 53018
So: besides setting up the parameters in the above Note and consider the Load balancing, as there any other major setups required to start this app server as a dual stacked instance?
Thanks in advance.
SAM
Edited by: SAM_ONE on May 14, 2010 3:45 AM
Edited by: SAM_ONE on May 14, 2010 3:55 AM

Migrating from single processor to dual processor Callmanager

Hi Networkers,
had anyone install a Callmanager 4.1 dual processor version of CM4.1-K9-X345D= before in a single CPU in a dual processor capable server before.
Can it work in the first place?
Had anyone successfully migrate it to a dual-processor later on?

I dont think there is any difference in Callmanager software for a dual processor versus single processor server. For 7845 (dual processor) the hardware detection disks may be different from the one for single processor (7825, 7835)
Migrating from one to another is as easy as taking a BARS backup from one server, build the other server to the same version and restore it. (Make sure server name and ip are the same for both servers)
Please remember to rate posts!

Upgrading from single CPU to dual ?

Hey,
With the multi-threaded OpenGL enabled by leopard on powerPC macs i was thinking of replacing the single 1.25 GHz CPU with a stock dual 1.25 GHz to improve performance in World of Warcraft. Any idea what if any i would gain in performance ?
Getting a mac pro is around 2 years off for me and i could pick up a dual CPU for a relatively cheap price.
Thanks

OK, I did a quick check of a technical manual.
You need to check the fabrication number on the logic board.
It's right next to the SLOT 5 PCI slot, the one farthest from the RAM slots.
It'll be of the format APPLE COMPUTER INC. 820-1308-A or similar number.
If it's 820-1308, 820-1440, or 820-1445, you can't just replace the CPU, there's a compatability issue between those logic boards and replacement CPU's (unless the CPU comes from a logic board with one of those fabrication levels. Apple recommends ordering a replacement logic board, CPU (part number 661-3654).
Otherwise you should be fine, although I'm concerned about taking a dual CPU from an MDD that pre-dates your single 1.25GHz G4 by a whole year.
When you get to dual CPU there may be some updates that need to be applied, I'm remembering a fix that disables one CPU on shutdown since having two active caused clock issues. Could have been part of a general OSX fix though.

Switching from single NIC to NIC bonding in "active" RAC

Hi
I have a 4 node RAC cluster on RHEL 4, running 10.2.0.3.0 in "semi-production".
"Everything" is multiplexed, except the NICs. The servers have 2 NIC ports one for public and one for interconnect.
If we add another NIC with 2 ports, is it possible to change the NIC configuration from single port to NIC bonding, without reinstalling CRS?
I can get a maintenance window, so this doesn't have to be done on the fly, I just need to know if its do-able.
I have checked some notes on MetaLink and for me it looks like this should be possible.
E.g. Note:436555.1 and Note:283684.1
Regards
Niklas

Nicke, Its very well doable and supported approach. You can use oifcfg to reconfigure the interfaces and there is no need to reinstall the CRS.
-Harish Kalra

Can we change the UCCX server from single node to the first node without affecting it's configurations

Hi all,
Firstly I was using the single CUCM7.0 server with the single UCCX 7.0 server. Now I am going to add the second CUCM and UCCX in the cluster. I was first configured the UCCX server as a single node. Now I have to configure this as a first node. How I could configure this from single node to the first node without affecting it's configurations..??????
Regards
Ali Raza

Hi Aaron,
How could we do the change on Imhost file. How we add the both servers in that file?
Below is the Imhost file txt.
# Copyright (c) 1993-1999 Microsoft Corp.
# This is a sample LMHOSTS file used by the Microsoft TCP/IP for Windows.
# This file contains the mappings of IP addresses to computernames
# (NetBIOS) names. Each entry should be kept on an individual line.
# The IP address should be placed in the first column followed by the
# corresponding computername. The address and the computername
# should be separated by at least one space or tab. The "#" character
# is generally used to denote the start of a comment (see the exceptions
# below).
# This file is compatible with Microsoft LAN Manager 2.x TCP/IP lmhosts
# files and offers the following extensions:
#      #PRE
#      #DOM:
#      #INCLUDE
#      #BEGIN_ALTERNATE
#      #END_ALTERNATE
#      \0xnn (non-printing character support)
# Following any entry in the file with the characters "#PRE" will cause
# the entry to be preloaded into the name cache. By default, entries are
# not preloaded, but are parsed only after dynamic name resolution fails.
# Following an entry with the "#DOM:" tag will associate the
# entry with the domain specified by . This affects how the
# browser and logon services behave in TCP/IP environments. To preload
# the host name associated with #DOM entry, it is necessary to also add a
# #PRE to the line. The is always preloaded although it will not
# be shown when the name cache is viewed.
# Specifying "#INCLUDE " will force the RFC NetBIOS (NBT)
# software to seek the specified and parse it as if it were
# local. is generally a UNC-based name, allowing a
# centralized lmhosts file to be maintained on a server.
# It is ALWAYS necessary to provide a mapping for the IP address of the
# server prior to the #INCLUDE. This mapping must use the #PRE directive.
# In addtion the share "public" in the example below must be in the
# LanManServer list of "NullSessionShares" in order for client machines to
# be able to read the lmhosts file successfully. This key is under
# \machine\system\currentcontrolset\services\lanmanserver\parameters\nullsessionshares
# in the registry. Simply add "public" to the list found there.
# The #BEGIN_ and #END_ALTERNATE keywords allow multiple #INCLUDE
# statements to be grouped together. Any single successful include
# will cause the group to succeed.
# Finally, non-printing characters can be embedded in mappings by
# first surrounding the NetBIOS name in quotations, then using the
# \0xnn notation to specify a hex value for a non-printing character.
# The following example illustrates all of these extensions:
# 102.54.94.97     rhino         #PRE #DOM:networking #net group's DC
# 102.54.94.102    "appname \0x14"                    #special app server
# 102.54.94.123    popular            #PRE             #source server
# 102.54.94.117    localsrv           #PRE             #needed for the include
# #BEGIN_ALTERNATE
# #INCLUDE \\localsrv\public\lmhosts
# #INCLUDE \\rhino\public\lmhosts
# #END_ALTERNATE
# In the above example, the "appname" server contains a special
# character in its name, the "popular" and "localsrv" server names are
# preloaded, and the "rhino" server name is specified so it can be used
# to later #INCLUDE a centrally maintained lmhosts file if the "localsrv"
# system is unavailable.
# Note that the whole file is parsed including comments on each lookup,
# so keeping the number of comments to a minimum will improve performance.
# Therefore it is not advisable to simply add lmhosts file entries onto the
# end of this file.
Regards
Ali Raza

K8N Neo4 Platinum 7125 - Switching from Single to Dual Opti - Startup Issues

My problem is the following:
I switched from Winchester 3200 single core to Dual Opteron 170.
The BIOS indicates it reading the both cores with the ACPI lingo.
I did patch the driver according to AMD with their specified download.
Now, when I start up the computer, I have to restart several times to get it to run but it does run although later locks up either when not in use or after an hour or so of gaming (mech warrior mercs) ???
I have checked the power supply voltages and they are as indicated in my profile, but I am wondering if the power
supply is not the problem. I know opterons' require a little more umph than normal single cores and this one is 4 years
old.
What do you folks think?
I would really hate to reinstall windows if it just a power supply issue.
Thanks in advance for you advise.
Civitas

Quote from: Civitas on 11-December-07, 03:28:29
Reinstalling the operating system seems like awful lot of work if its the power supply.
But I appreciate the advice.
This rig is about 3 years old. I will probably wait until I have some time to do this.
What drivers do you think I need to get the USB function again for now?
Thanks.
Civitas
"Reinstalling the operating system seems like awful lot of work if its the power supply."
Get a decent PSU and re-test 1st, here can be found good PSU suggestions.
https://forum-en.msi.com/index.php?topic=112039.msg836246#msg836246
"What drivers do you think I need to get the USB function again for now?"
Just delete them from device manager, then windows should detect and install them automatically.

Convert PXIe-8135 controller to dual-boot Windows 7 and LabVIEW RT

Hello. I have a PXIe-8135 controller that originally was just running Windows 7. We are trying to convert it to a dual boot system to also run LabView Real Time. (There is host computer that will run LabVIEW 2014 with the RT module, and the controller will become a target).
I have created a FAT32 partition on the hard drive of the controller. Now, I’m trying to install the real-time OS with a USB flash drive made using the MAX utility, but I cannot boot using the USB drive for some reason. I keep getting the message “waiting for USB device to initialize”.
In BIOS, legacy USB support is [ENABLED] and boot configuration is set to [Windows/other OS]. I’ve tried removing the drive, waiting, and reinserting. I’ve tried two different USB drives (both 8 GB, different brands).
I’m not sure what to do next. Apart from the USB boot issue, is converting the PXIe-8135 even possible? I read about SATA/PATA hard drive issues with older controllers, but I don't know about this one.
Thanks, in advance, for your help!
-Jeff
Solved!
Go to Solution.

Per Siana's licensing comment, more information on purchasing a deployment license if you do not have one for this target can be found here.
The RT Utility USB key is used to set up non-NI hardware with LabVIEW Real-Time, but you should not need it in this situation to convert to dual-boot (*). Try this:
1. Since you already have a FAT32 partion created, go into BIOS setup and change to booting 'LabVIEW RT'.
2. The system will attempt to boot LabVIEW RT, see that the partition is empty, and switch over into LabVIEW RT Safe Mode. (this safemode is built into the firmware, which is why you don't really need the USB key).
3. The system should come up correctly and be detectable from MAX, and you can proceed with installing software.
4. To switch back to Windows, go back to BIOS setup and choose 'Windows/Other OS'
(*) One area where the USB key is helpful on a dual boot system is with formatting the disk. If you want to convert from FAT32 to Reliance on the partition designated for LabVIEW RT, the USB key lets you attempt to format a single parition and leave the rest of the disk untouched. If you format from MAX, the standard behavior is to format only one RT partition if found, but if not found, it will format the entire disk. Formatting from MAX on a dual boot system is consequently riskier and you could lose your Windows partition.

Single DVI to Dual DVI

I own a 23" Apple clear-plastic-case display with an ADC connection. I also own an Apple DVI to ADC converter. Is it possible to use some sort of adapter to vonnect my display to a Dual DVI connection? Thanks.

When you take the Apple DVI-to-ADC connector (with power supply) and attach it to your ADC display, it converts your display into a DVI display with a power supply "brick" in the cable. ANY DVI computer output (Single-Link or Dual-Link, or adapted from something else) can be used to power your new hybrid DVI display, since it 1920 wide or less.

Multiple IC Billing from Single Delivery

Hi,
we are using SAP IS Retail ECC6 with multiple company inside it. currently, we do PO intercompany (PO Type NB) with delivery type NLCC. management need to split the Billing document from single delivery. company A create PO to company B. delivery document created by VL10B on company A. this delivery document good issued by company B and gr done by company A. for example, on delivery item X with 100 quantity already PGI. but management need company B create billing with quantity sold done company A.
i already change on vov7 as per picture below:
on VTFL i already configured as below:
on V/CL, auto batch determination not active
but when we create an invoice via VF01 > selection list. the open quantity is disabled (grayed):
can anyone help me, why its still grayed? if there is any wrong configuration please let me know.

Go VF01, click on selection list button (fn key - F2) and you can modify the quantity there.
Note - you should be in the main VF01 screen and not the after you click enter or click process.

Broker switchover from single ins to 2nodesRAC problem

hello,
i installed and configured 11Gr2 2 node rac primary. and single instance grid + single instance database 11gr2 standby side.
but there is a problem. primary database name is the same for all rac nodes of me (kkrac). there are 2 instances; kkrac1 and kkrac2.
when i tried to switchover to 'kkrac' back from standby side(kkguard).. broker is looking for dr1kkrac.dat and dr2kkrac.dat files. but they dont exist. and they are wrong file names. it should be instance names; like dr1kkrac1.dat dr2kkrac2.dat.
and so i copied and renamed .dat files from guard to primary nodes (node1, node2); but it didnt work:)
DRCX: DRC Unique ID mismatch...
question)
i want to swichover "from single instance" db TO "2 nodes RAC db" with broker;
if i use the same db name for rac nodes (kkrac), it fails because, brooker dr1kkrac.dat dr2kkrac.dat files dont exist.
how can i do it correctly?
best regards;
CREATE CONFIGURATION 'KKGUARDCONF' AS PRIMARY DATABASE IS 'kkrac' CONNECT IDENTIFIER IS 'kkrac';
ADD DATABASE 'kkguard' AS CONNECT IDENTIFIER IS 'kkguard';
DGMGRL> show configuration
Configuration - KKGUARDCONF
Protection Mode: MaxPerformance
Databases:
kkrac - Primary database
kkguard - Physical standby database
Fast-Start Failover: DISABLED
Configuration Status:
SUCCESS
DGMGRL> switchover to 'kkguard'
Performing switchover NOW, please wait...
New primary database "kkguard" is opening...
Operation requires shutdown of instance "kkrac1" on database "kkrac"
Shutting down instance "kkrac1"...
ORA-01031: insufficient privileges
Warning: You are no longer connected to ORACLE.
Please complete the following steps to finish switchover:
shut down instance "kkrac1" of database "kkrac"
start up instance "kkrac1" of database "kkrac"
DGMGRL> show configuration
Error:
ORA-03114: not connected to ORACLE
Configuration details cannot be determined by DGMGRL
DGMGRL> connect /
Connected.
DGMGRL> show configuration
Configuration - KKGUARDCONF
Protection Mode: MaxPerformance
Databases:
kkguard - Primary database
kkrac - Physical standby database
Fast-Start Failover: DISABLED
Configuration Status:
SUCCESS
Edited by: donniedarko on 23-Dec-2010 07:01

It is lool like the new standby database is started from old home:
alert log:
Starting up:
Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options.
Using parameter settings in server-side spfile /u01/app/oracle/product/11.2.0/db_1/dbs/spfileDB1.ora
System parameters with non-default values:
My old home (11.2.0.1) u01/app/oracle/product/11.2.0/db_1
My new home (11.2.0.2) u01/app/oracle/product/11.2.0/db_2
previous start this database:
alert log:
Starting up:
Oracle Database 11g Enterprise Edition Release 11.2.0.2.0 - 64bit Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options.
Using parameter settings in server-side spfile /u01/app/oracle/product/11.2.0/db_2/dbs/spfileDB1.ora
System parameters with non-default values:
Why database is starting from old home?
I Changed directories in .bash_profile oracle OS user.

Transfer from Single Edition App to Multifolio

Can I use the same name of the app (APP ID), if I wanted to change my app from single editon to multifolio (pro or enterprise)?

Yes. Just upload the new viewer configured as a multi-folio app to iTunes, replacing the old one. You might have to contact product support to get them to reset the version number for you to one that is larger than the previous single edition app's version number.
Neil

Server status shown as 'Not Configured' in single server farm.

In a single server farm, after installation and running the configuration wizard for multiple times, the status of server is shown as 'Not Configured'. There is no abnormality in any other features (so far), everything functions fine, but we see the 'Not
configured' message in 'Servers in Farm' and 'Manage Patch Status'. We have used the same AutoSPInstaller script to install Sharepoint on two machines SPDev1 and SPDev2. This error does not show up on SPDev1 but on SPDev2. Is this something to worry
about ?

Hi ,
According to your description, my understanding is that the server status showed “Not Configured” in single server farm.
Please run SharePoint 2013 Products Configuration Wizards to remove the server from the farm via clicking “Disconnect the existing farm”. After finishing, re-run configuration wizards to connect the existing farm.
Best Regards,
Wendy
Wendy Li
TechNet Community Support

Activation is changed from single lookups to to package fetch of active tab

I was going through some of the Performance enhancements in BW 7.3. Could someone please explain what do the following mean?
1. DSO Activation is changed from single lookups to package fetch of active table
2. Optimized delta load for master data due to package fetch instead of single look-ups
Thanks & Regards
Dharmendra

Just thought I'd post the resolution:
1) Simply changing the Disc Media Type in the ProjectData folder does nothing. The dual-layer setting causes it to change from a value of 4 to 8 (guess that's no surprise), but iDVD still treats the drive as a single-layer drive and so you can't create a disc image based on a dual-layer disc.
2) Turns out the folks from MCE sent along, after requesting it, a patch to enable dual-layer support in iDVD. From what I can tell from the .command file, it looks like it's probably just the HardMac.com hack repackaged for convenience. The don't offer it for download, but if you call or email them, they'll send it.
Thanks again for your advice.

Faster way to migrate from Single byte to Multi byte

Hello,
We are in the process of migrating from a 9i Single byte db to a 10g Multi byte db. The size of our DB is roughly 125 GB. We have fixed everything in the source database (9i) in terms of seamlessly migrating from a single byte to a multi byte db. The only issue is the migration window - curently we are doing an export/import since there is a character set migration involved and it's taking about 20+ hrs to do the import in 10g. The management wants to cut this down to less than 10 hours, if that's possible. I know the duration it takes to import depends on many factors like the system/OS configuration, SAN, etc but I wanted to know what , in theory, is considered the fastest method of migrating a database from single byte to multi byte.
Have anybody here gone through this before?
Thanks,
Shaji

If the percentage of user tables containing some convertible data (I am assuming you will not have any truncation or lossy data) is low, you can export only those tables, truncate them, and rescan the database. This should report no convertible data, except some CLOBs in Data Dictionary. Such database can be migrated to AL32UTF8 using csalter.plb. After the migration, you import only the previously exported subset of tables.
Note, for this process to work, no convertible VARCHAR2, nor CHAR, nor LONG data can be present in the Data Dictionary.
The process should be refined by dropping and recreating indexes on the exported tables as recreating an index is faster then updating it during import. You should also disable triggers so that they do not interfere with the migration (for example, they should not update any "last_updated" timestamp columns).
If the number and size of affected tables is low compared to the overall size of the database, the time saved may be significant.
There may also be tables that require even more sophisticated approach. Let's say you have a multi-gigabyte table that stores pictures or documents in a BLOB column. The table also has a single text column that keeps some non-ASCII descriptions of the stored entities. Exporting/truncating/importing such table may be still very expensive. A possible optimization is to offload the description column to an auxiliary table (together with ROWIDs), update the original column to NULL, export the auxiliary table, drop it, rescan the database, migrate with csalter.plb, re-import the auxiliary table, and restore the original column. If pictures alone occupy, for example, 30% of the whole database, such approach should yield significant time saving.
-- Sergiusz

Configuration from Single Controller to Dual in SE 3510

Similar Messages

Maybe you are looking for