Configuration Help Needed - Layout of Public Access and Private Access Network
HELP
I need help in laying out the following network - herre is my first stab at it.
1. Actiontec DSL Modem - DHCP On ----- Model GT701-WG
WAN IP Address 12.17.66.203
WAN SubNet Mask 255.255.255.255
Lan IP Address 192.168.0.1
Lan SubNet Mask 255.255.255.0
2. WRT54G - DHCP On ---------------- Open to Public Access to the Internet
Local IP Address 192.168.1.1
Subnet Mask 255.255.255.0
3. DellPowerConnect 2708 Switch --- Open to Public Access to the Internet
4. MS Windows SBS2003 Server --- Closed to Public Access
Connecting to the #2 WRT54G thru a Linsys network card
5. WRT54G - DHCP Off - ??? --------- Closed to Public Access
Connecting to another Linksys network card in the SBS2003 Server
Local IP Address 192.168.1.2 ???
Subnet Mask 255.255.255.0
6. Linksys SD216 Switch --- Closed to Public Access
Any help would be greatly appreciated
I got the network setup, but did not get what you are trying to do. Do you have 2 WRT54Gs there? Are you trying to turn off DHCP server of second WRT54G? A detailed information would be appreciated.
Similar Messages
-
1941W configuration help needed
Our Deployment Scenario:-
1941W Gigabit Ethernet 0/0 is connected to the PPOE connection of the ISP.
Gigabit Ethernet 0/1 is connected to the wired LAN
I have created 2 wireless radio Cisco_Kamran_BGN which is operating at 2.4 Ghz Devices and Cisco_Kamran_A which is operating at 5Ghz Devices.
I have created 2 VLans for the Wireless.
Vlan 10 for Cisco_Kamran_A 192.168.10.x
Vlan 11 for Cisco _Kamran_BGN 192.168.11.X
The problem is the Wireless users are not getting the IP address from the respective DHCP server which has been configured on the Router.
Can please any from the community help me and show me where I am missing the configuration.
Please find my router & ap configuration below.
Router Configuration
Router#
sh run
Building configuration...
Current configuration : 3022 bytes
! No configuration change since last restart
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable secret 5 $1$TdQt$npYeaf/W0kRElcfMggzJ31
no aaa new-model
service-module wlan-ap 0 bootimage autonomous
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.50
ip dhcp excluded-address 192.168.10.1 192.168.10.10
ip dhcp excluded-address 192.168.11.1 192.168.11.10
ip dhcp pool DHCP
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_A
network 192.168.11.0 255.255.255.0
default-router 192.168.11.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_BGN
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
dns-server 195.225.241.222 213.42.20.20
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO1941W-E/K9 sn FCZ1553C1VK
hw-module ism 0
redundancy
bridge irb
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered GigabitEthernet0/0
arp timeout 0
no mop enabled
no mop sysid
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface Wlan-GigabitEthernet0/0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
no ip address
interface Vlan10
ip address 192.168.10.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Vlan11
ip address 192.168.11.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp pap sent-username xxxxxx password 0 xxxxxx
ppp ipcp route default
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list DSL_ACCESSLIST interface Dialer1 overload
ip access-list extended DSL_ACCESSLIST
permit ip 192.168.0.0 0.0.255.255 any
control-plane
line con 0
password xxxxxx
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password xxxxxx
login
transport input all
scheduler allocate 20000 1000
end
Router#
Router#
Router#
Access Point Configuration
ap#
ap#
ap#
sh run
Building configuration...
Current configuration : 2603 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$JxdQ$a2/00bWJuhUKP9QLC94YD/
no aaa new-model
dot11 syslog
dot11 ssid Cisco_Kamran_A
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 1045081417161C5A555C7A7B
dot11 ssid Cisco_Kamran_BGN
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 020D05561907017015165949
username Cisco password 7 14341B180F0B
bridge irb
interface Dot11Radio0
description 802.11bgn radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
broadcast-key change 3600
ssid Cisco_Kamran_BGN
antenna gain 0
station-role root
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1
description 802.11a radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Cisco_Kamran_A
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.10
description 802.11a bridge
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0.11
description 802.11bgn bridge
encapsulation dot1Q 11
no ip route-cache
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
no activation-character
line vty 0 4
login local
end
ap#
ap#
ap#Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting Started with Wireless - View the full discussion
conf t
interface Dot11Radio0
no ssid Cisco_Kamran_BGN
no encryption mode ciphers aes-ccm
exit
interface Dot11Radio1
no encryption mode ciphers aes-ccm
no ssid Cisco_Kamran_A
exit
dot11 ssid Cisco_Kamran_A
vlan 10
dot11 ssid Cisco_Kamran_BGN
vlan 11
exit
interface Dot11Radio0
encryption vlan 11 mode ciphers aes
ssid Cisco_Kamran_BGN
exit
interface dot11radio0.1
encapsulation dot1q 1 native
bridge-group 1
interface dot11radio 0.11
encapsulation dot1q 11
bridge-group 11
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
exit
interface Dot11Radio1
encryption vlan 10 mode ciphers aes-ccm
ssid Cisco_Kamran_A
interface dot11radio1.1
encapsulation dot1q 1 native
bridge-group 1
interface dot11radio1.10
encapuslation dot1q 10
bridge-group 10
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home -
Multiple ethernet network adaptors + MySQL/php5: configuration help needed
I would be grateful if someone could give me some advice on how to configure multiple ethernet adapters under OS X 10.5.6
I have set up my system to work nicely with two ethernet network adapters, each with its own fixed IP. This bit works just fine. The machine supports two separate servers - a mail server and the OS X Apache2 server. I have configured the mail server to only listen to one of the IPs, and the Apache2 server to listen to the other (via httpd.conf). The system also has MySQL and php5 installed / enabled, and these services are only used by the Apache2 server.
The problem I have is that when I start the machine, initially the php5 system cannot connect reliably to the MySQL database system. The fix I have found is to temporarily make the ethernet adapter connected to the mail server 'inactive'. While this is so, the php5/MySQL connection to Apache2 works. Curiously, once an initial connection between php5 and MySQL has been made, subsequently I can make the mail server's ethernet adapter active again without further problems.
I initially thought this might be due to 'service order' issues - but changing the service order (e.g. putting the Apache adapter 'above' the mail adapter in the service order does not help. The fix only works by making the mail adapter inactive temporarily.
I suspect that there is some configuration change I can make to clarify the setup I have. The MySQL and Apache installations only need to talk to the Apache server - but I am not sure how to record this configuration in the OS X system.
Thanks in advance for any assistance that you can provide.
Message was edited by: Gavin LawrieHi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting Started with Wireless - View the full discussion
conf t
interface Dot11Radio0
no ssid Cisco_Kamran_BGN
no encryption mode ciphers aes-ccm
exit
interface Dot11Radio1
no encryption mode ciphers aes-ccm
no ssid Cisco_Kamran_A
exit
dot11 ssid Cisco_Kamran_A
vlan 10
dot11 ssid Cisco_Kamran_BGN
vlan 11
exit
interface Dot11Radio0
encryption vlan 11 mode ciphers aes
ssid Cisco_Kamran_BGN
exit
interface dot11radio0.1
encapsulation dot1q 1 native
bridge-group 1
interface dot11radio 0.11
encapsulation dot1q 11
bridge-group 11
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
exit
interface Dot11Radio1
encryption vlan 10 mode ciphers aes-ccm
ssid Cisco_Kamran_A
interface dot11radio1.1
encapsulation dot1q 1 native
bridge-group 1
interface dot11radio1.10
encapuslation dot1q 10
bridge-group 10
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home -
Troubleshooting help needed: My iMac keeps crashing and restarting with a notice: "Spinlock application timed out" What can I do?
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the page that opens.
Select the most recent panic log under System Diagnostic Reports. Post the contents — the text, please, not a screenshot. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header and body of the report, if it’s present (it may not be.) Please don't post shutdownStall, spin, or hang reports. -
When I try to connect to a WiFi network that I need a screen pops up and says "The network you're attempting to join requires you to install a profile on your Apple TV." What does this mean?
Yes, home sharing requires both to be on the same wifi network. As it stands access to the network requires the login via webpage, which cannot be done on Apple TV. You will need to speak to IT in order to grant access for the device.
-
WLAN Controller configuration help needed
Hi,
I need to configure AP with WLAN controller for guest access. we have 2 vlans. vlan 1 - guess vlan (internet only access) and vlan 2 - all access.
while configuring wlan controller. which vlan should i configure as native vlan? I have radius server which would check health of the user and would direct wlan controller to put in user in vlan 1 or 2 depending on its credentials.
please advise how to implement it. what would be initial steps.Hi,
I have couple of doubts before going further for solution to implement ?
What model of wlan controller & AP , you are using ?
to configure the Controller , initially you need to configure the interface ( which are virtual ) .
You need to connect controller to your existing LAN set-up may be one of the port of your core switch ............
below are the interface which you need to configure in controller .......
1) Management interface with IP ( which will be used to access your controller from lan ... ) this is ip should be able to ping from the network.
2) AP manager IP ( this is again depend on model ) if it is 5500 , this is not required ..
3) Virtual IP : this is should the IP address which is not at all there in your lan eq.1.1.1.1
4) dynamic interface with IP : this is the interface which will map your vlan to WLAN
once you create the mentioned interfaces , you need to create the wlan and map the above dynamic interface with respective wlan.if required you can configure the DHCP pool as well in controller for Wlan.
let me know , whether this information helped you ........................ -
Help Needed in Creating Java Class and Java Stored Procedures
Hi,
Can anyone tell how can i create Java Class, Java Source and Java Resource in Oracle Database.
I have seen the Documents. But i couldn't able to understand it correctly.
I will be helpful when i get some Examples for creating a Java Class, Java Source and Stored Procedures with Java with details.
Is that possible to Create a Java class in the oracle Database itself ?.
Where are the files located for the existing Java Class ?..
Help Needed Please.
Thanks,
Murali.vHi Murali,
Heres a thread which discussed uploading java source file instead of runnable code on to the database, which might be helpful :
Configure deployment to a database to upload the java file instead of class
The files for the java class you created in JDev project is located in the myworks folder in jdev, eg, <jdev_home>\jdev\mywork\Application1\Project1\src\project1
Hope this helps,
Sunil.. -
I manage 60 ipads for a school using Apple Configurator. Need to update my devices to iOS7 and Apple Configurator to 1.4.3...Is it best to use Mountain Lion or Mavericks, as I also need to update from Lion 10.7 for the new Apple Configurator and iOS7 to work properly.
I always run a Time Machine backup before updating anything and recommend you run a backup as well. Paid apps should migrate over without any problem. If you have problems with VPP codes not transfering over properly, you can talk to your Apple SE or contact VPP for Education support and they can help you. While I haven't experienced any problems with updating, its never a guarantee that others will have the same experience.
Good luck!
~Joe -
Help Needed with XML Attribute Access (Bold/Italics)
Hi,
I have a form that displays data in livecycle designer. When someone imports an xml file into the form in Adobe Acrobat it should be able to display some data as bolded and some italicized based on the xml file.
Here is the sample xml file
<Table1>
<Row1>
<Cell1 style="none">1</Cell1>
<Cell2 style="bold">2</Cell2>
<Cell3 style="italics">3</Cell3>
</Row1>
</Table1>
And the output should be:
1 2 3
Can someone please help! If the xml file should be designed differently please let me know.
Thank you!Paul,
Thanks for the help! I tried it out and it worked. One last question please. According to your explanation I added to the xml file the tags
<body xmlns:xfa="http://www.xfa.org/schema/xfa-data/1.0/" xmlns="http://www.w3.org/1999/xhtml" xfa:APIVersion="Acroform:2.7.0.0" xfa:spec="2.1">
<p style="font-weight:bold;">2</p>
</body>
do I need to place this body tag around each number or can I place it in one location in the xml file?
Thanks again. -
Help needed with 3rd party software and Windows XP on MacBook
My Brother embroidery software has stopped working on the XP side of my MacBook. After all kinds of uninstalling and installing with support from Brother, they decided the problem is not the software and I should "contact my computer company." Since this is really a Mac, would Apple be able to help me with a Windows issue? The genius bar said no, Microsoft says no, so what is the point of buying a using a dual platform machine if no one takes responsibility for helping? I'm very frustrated and could use help from someone who works on both platforms.
*"would Apple be able to help me with a Windows issue?"*
Sorry, but no. Apple does not support third party operating systems and applications. -
Help: Factory Class using Inner Class and Private Constructor?
The situation is as follows:
I want a GamesCollection class that instantiates Game objects by looking up the information needed from a database. I would like to use Game outside of GamesCollection, but only have it instantiated by GamesCollection to ensure the game actually exist. Each Game object is linked to a database record. If a Game object exist, it must also exist in the database. Game objects can never be removed from the database.
I thought about making the Game object an inner class of GamesCollection, but this means that Game class constructor is still visible outside. So what if I made Game constructor private? Well, now I can't create Game objects without a static method inside Game class (static Object factory).
Basically what I need is a constructor for the inner Game class accessible to GamesCollection, but not to the rest of the world (including packages). Is there a way to do this?leesiulung wrote:
As a second look, I was initially confused about your first implementation, but it now makes more sense.
Let me make sure I understand this:
- the interface is needed to make the class accessible outside the outer classBetter: it is necessary to have a type that is accessible outside of GameCollection -- what else could be the return type of instance?
- the instance() method is the object factory
- the private modifier for the inner class is to prevent outside classes to instantiate this objectRight.
However, is a private inner class accessible in the outer class? Try it and see.
How does this affect private/public modifiers on inner classes?Take about five minutes and write a few tests. That should answer any questions you may have.
How do instantiate a GameImpl object? This basically goes back to the first question.Filling out the initial solution:
public interface Game {
String method();
public class GameCollection {
private static class GameImpl implements Game {
public String method() {
return "GameImpl";
public Game instance() {
return new GameImpl();
public static void main(String[] args) {
GameCollection app = new GameCollection();
Game game = app.instance();
System.out.println(game.method());
}Even if you were not interested in controlling game creation, defining interfaces for key concepts like Game is always going to be a good idea. Consider how you will write testing code, for example. How will you mock Game? -
EPM 11.1.1.3 Shared Services Configuration help needed
Hi,
I am currently running into issues when trying to configure Shared Services via the EPM System Configurator 11.1.1.3. I've installed Weblogic 9.3 MP3 with all of the default options (including establishing Node Manager as a service). I've also created a seperate userId in Weblogic called hyperion (with the password of hyperion) so that EPM can access the instance against the default web server.
When I run the configurator to try and deploy to application server, the status sits there on the "Starting WebLogic 9 Admin Servers" and does nothing.
Sometimes is does get past that but then the deployment fails because it is unable to deply the interop.war.
Any help would be greatly appreciated as I'm 100% stuck!
Thanks,
AnjuHi,
I am not sure what your issue is but I do know that you don't have to start creating users in weblogic. Usually you do a standard install of weblogic, if you are not going to use it you don't need the node manager set up.
Cheers
John
http://john-goodwin.blogspot.com/ -
Help needed for javax.naming.Context and javax.naming.InitialContext
I need help on this two..
I am currently doing a project which required Connection Pooling. And this is the first time i'm exposed to all this.. I know nothing about these files.. But, i manage to get help from someone on DataSource. But i can't find any for naming.context and naming.InitialContext.. Can anyone help me? I need to know where i can get these 2 files or how to configure it.. Thanks! ;pThis'll help you:
http://java.sun.com/products/jndi/tutorial/ -
Help needed : How to move OCR and Voting Disk
Hi all experts...
I am Mahesh. Working in DXB as DBA. We have serveral RAC installed clients. Among those one major client wants their OCR and Voting Disk to be moved from existing SAN to a new SAN which will be configured. Only OCR and Voting Disks needs to be moved.
Details:
=====
Oracle Clusterware,ASM and DB version 10.2.0.3.0
Windows 2003 Server Enterprise Edition
2-Node RAC
OCR and Voting disks are on RAW devices (not on CFS or NFS)
I have read the clusterware administration document and also Metalink Note 428681.1 for the same.
But it does not contain information how to move it to another new RAW in a new SAN device. (we need to keep it in raw device itself)
How to identify the new disk path from windows operating system ? Then only we can move the OCR and VD right ???
Help me for the same please...
Thanks & regards,
Mahesh.Hi Mashes,
Could you list out the steps you did after you create the link on the new SAN using GUIObjectManager.exe?
I tried on my VM and also in customer's test environment but I only successful using the following steps
1. shutdown asm service, database service, listener service, CRS, EVM and CSS
2. Object Manager Service is kept running
3. from both nodes I issued the following command
ocrconfig -repair \\.\OCRPRIMARY
ocrconfig -repair \\.\OCRMIRROR
4. according to metalink id 428681.1, I should do the following
ocrconfig -overwrite
However I was not successful because that command returns an error message (PROT-1: Failed to initialize ocr config).
Therefore, I ran the following command
ocrconfig -restore D:\oracle\1020\CRS\cdata\crs\backup00.ocr
5. after that command, ocrcheck giving me the result and the ocr primary and mirror have been moved to the new partition.
6. start the whole services starting from CSS, EVM, CRS, ASM, Listerner and Database service.
Although what I experienced seems a bit weird and not the same as what was written in metalink, the RAC is running fine until now.
What I would like to know is your experience on this. May be you can share it here.
Thank you,
Adhika -
IPlanet/Sun ONE Directory Server 5.1 configuration help needed.
Hi from Finland.
We have a SunFire 420 running Solaris 8.
It has 2 network adaptors each configured to have separate IP addresses. Eventually these cards will be on quite separate networks... one for intranet users and one for the rest.
What I am wanting to know is how do I configure the iDS 5.1 to be listening on port 389 for both IPs
When I installed iDS 5.1 I could only see one hostname and one domainname so the install went fine.
Is the Directory with multiple network adaptors setup an O/S issue or an iDS issue???
Any tips or help would be gratefully accepted!!All my PROD systems have dual n/w cards listenning on different IPs(subnets for that matter). Data can be accessed over LDAP on both IPs with the same port. We did not have to do anything special at the Directory or the OS level.
Maybe you are looking for
-
After the CD install failed with the "Installer failed to initialize" ewrror I contacted support and they gave me a download link... same error message.
-
Use of MDX in 7.x and higher
Hi All,<BR>I am new to MDX. can someone tell me where exactly does MDX comes into function in Essbase. From the documentation i know that it is used for writing formulas in ASO database and extract data. I would like to know how can i extract data us
-
My iPod won't allow me to update to iOS 5, it is currently on 4.2.1. My iTunes is updated to the latest one but every time I press Check for Update it says "This version of the iPod software (4.2.1) is the current version" The model of the iPod as it
-
I purchased an i-pad 2 (16GB) and have about 330 apps. I cannot download or even update my apps (get the message there is not enough storage available to download). I purchased more storage through settings, but still nothing. Help?
-
DBACOCKPIT : DBA CALENDAR ( DB13 ) not in sync
Hello, In Solution Manager DBACOCKPIT the DBA Calendar for the remote systems, when I check the tasks scheduled, they are not in sync with the actual scheduled tasks ( DB13 ) in the remote systems. Does anyone has any idea how to fix it? SAP Versio