Configuration of AirPort Extreme Using Third Party LAN Ethernet Adapter?

Hello;
I am trying to set up my own wireless connection, not without great consternation. Any help would be greatly appreciated. Here is my current situation:
Subscribed to DSL service - installation went well, and it works fine on two other computers (that are not wireless). Installed same in computer that will use airport extreme, and it shows a connection, but won't load the browser pages.
Airport Extreme Base Station is working, software installed, etc., but computer doesn't offer airport as a connection choice in system preferences, internet connect, Airport set-up assistant, etc. (because there's no airport card installed????). Consequently, I can't finish w/airport set-up assistant.
I'm using a third party LAN ethernet wireless adapter since I was told airport cards for my G-4 are no longer made. Adapter and software installed, and shown to be working.
What am I missing?
Thanks
KAS
PowerMac G-4 Mac OS X (10.3.9)
PowerMac G-4 Mac OS X (10.3.9)

Hello Duane
Thank you for your warm welcome and quick response. I will try the AirPort Admin Utility. Your help is greatly appreciated!
-K
PowerMac G-4 Mac OS X (10.3.9)

Similar Messages

Airport Extreme and third party wireless routers

I have a dual-band Airport Extreme that works well with all of my newer Macs. I have older laptops, however, with PCMCIA wireless cards that can't do WPA2-Personal security, only WEP. My only solution has been to set up a Guest network with no security. Is it possible to connect a third-party wireless router to the Airport Extreme that offers WEP security?

Are you trying to setup the Belkin router to use the same wireless network name as the AirPort Extreme network?
That would require that that the Belkin's network use the same security.
If this is the case, try setting up the Belkin with a different wireless network name. Unless the Belkin is really limited in features, you should be able to choose the type of wireless security to be used on this Belkin network.
If you can do this, "point" your WEP device at the wireless network that the Belkin is producing and the signal will bridge when it reaches the AirPort Extreme.
Regading your question about connecting a router to the ethernet port on a computer that is already setup for Internet Sharing...this is not likely to work. I very much doubt that you would be able to get an Internet connection with this type of setup.
Message was edited by: Bob Timmons

How do I configure my Airport Extreme in Lion?

I could configure my Airport Extreme using the disk provided when running Snow Leopard. The upgrade to Lion appears to have 'uninstalled' the utility. Now when I try to reinstall it it tells me that it can't install it on the hdd because
"The version of Mac OS X on this volume is not supported"
What do I do now?
Thanks
Andy

You should not still be using that disk. There should be an up-to-date version of the AirPort Utility in the Utilities folder in your Applications folder. Use that. If it's not there, there's something wrong. If it's missing, in Snow Leopard I would have said to use Pacifist to extract that from the installer, but I don't know if that works with Lion's installer or not.

Unable to connect Brother printer to Airport Extreme using USB

Hi, I recently bought a Brother HL-2270DW printer, which has 802.11 b/g wireless capabilities. My airport extreme (2008 model) is set to 802.11 n (5 ghz), so I can't set-up the printer wirelessly to the airport extreme without changing to 802.11 b/g. Instead I'm fine hooking up the printer to the airport extreme using a USB. When I first turn on the printer, I can print from my Macbook, but after a few minutes, the printer goes offline and has to be turned off/on. When I try to Open Printer Utility, there is a connection error. I have the right driver installed, and I can print fine for a few minutes after turning on the printer, and all the time when the printer is connected to the Macbook directly using the USB. I would like to use the printer by connecting it to the airport extreme using the USB or Ethernet. Any help would be much appreciated, thanks,

Please explain exactly what you're experiencing that leads you to claim that.
The current firmware of the TiVo Premier is easily confused about whether it's connected to the Internet or not. In my experience, a TiVo unit will quickly regain its senses and decide that it really is connected.

How can i telnet or get access to other LAN members in LAN without using third party software?

I have admin access to the main router in our LAN, so how can i telnet or get access to other LAN members in LAN without using third party software?
its linksys3500 router and i login as admin using the gateway address in address bar..
i want to access the c drive of my colleague in same subnet in same office and i know his ip address.but he not configured telnet accept request.so without it how can i open his telnet port and access him

I think you are using the wrong terminology. You can browse the hidden share of any pc if you know the ip and have a valid user account on the pc by typing in the following \\computername\c$ or \\ipaddress\c$ . It should prompt you for a user account. You may have to allow this through the windows firewall (or disable it completely).

I have admin access to the main router in our LAN, so how can i telnet or get access to other LAN members in LAN without using third party software?

I have admin access to the main router in our LAN, so how can i telnet or get access to other LAN members in LAN without using third party software?
its linksys3500 router and i login as admin using the gateway address in address bar..
i want to access the c drive of my colleague in same subnet in same office and i know his ip address.but he not configured telnet accept request.so without it how can i open his telnet port and access him

Duplicate post.

I enabled the guest network feature on my time capsule. Can I configure my airport extremes guest network feature if I use this as a network extender using a "roaming" network?

I enabled the guest network feature on my TC. Can I configure my airport extremes guest network feature if I use the extreme as a network extender connecting my Airport Extreme to my TC via ethernet cable?

Unfortunately no, since the AirPort Extreme should be configured in Bridge Mode if it is connecting to the Time Capsule using an Ethernet connection.
The Guest Network option cannot be enabled when the AirPort is configured in Bridge Mode.
Another way of saying the same thing is that the Guest Network cannot be "extended" either by using an Ethernet connection or wireless. It is only available from the Time Capsule "main" wireless router on your network, not any extending devices.

Macbook Pro cannot configure AirPort Extreme using AirPort Utility

Hi all,
I can't get my macbook pro's airport utility to connect to my airport extreme, and hard reset doesn't seem to work either. However, the airport extreme still functions properly... just doesn't allow me to reconfigure it.
Steps to reproduce:
1. Open AirPort Utility.
--> my AirPort Extreme router shows up with a green light (it's working).
--> Information displayed includes "AirPort Utility found an AirPort Extreme with 802.11n (Gigabit Ethernet)", with correct-looking gateway and IP information (version 7.2.1)
2. Click "Continue"
--> Screen shows "Reading base station configuration..." with a little spinning icon.
3. Wait 3 minutes.
--> During this wait, the green light stays lit on the router, my wireless connection does not drop, and the icon next to "Reading base station configuration..." continues to spin.
4. Popup dialog appears: "An error occurred while reading the configuration. Please make sure your AirPort base station is plugged in and in range of your computer or connected via Ethernet and try again. (-6753)". The AirPort extreme is sitting 2 feet from my MacBook Pro, connected only by wireless internet.
At this point, I wonder whether hooking it up with an ethernet cable would work better. So I did the following:
1. Turn off Macbook Pro Airport wireless card.
2. Connect an ethernet cable from the laptop to the 2nd port of the Airport Extreme
3. Wait 60 seconds for DHCP etc.
4. Close the Airport Utility (from the last test)
5. Open the Airport Utility again
6. My Airport Extreme router is again displayed, the same information is present as before.
7. Click Continue
--> "Reading base station configuration..." message with spinning icon appears again.
8. Wait 3 minutes. During this time, as before, the green light on the router stays lit, and nothing much seems to happen. I ran a "ping google.ca" from a terminal window just to verify that my internet stayed connected during this process, and the pings all responded fine.
9. Again, an error popup: "An error occurred while reading the configuration. Please make sure your AirPort base station is plugged in and in range of your computer or connected via Ethernet and try again. (-6753)"
At this point, I decided it might be a good idea to do a hard reset. I pressed and held down the tiny button on the back of the Airport Extreme for 6 seconds then released... no visible result. Green light still on. Then I tried for 11 seconds. Still no result, green light still on. I restarted the router, waited for the green light to come back on, and tried again with 6 seconds then 11 seconds again. STILL no result.
I can't think of anything else to try. Any suggestions?

The Windows "Airport Setup" version you need for the Airport Extreme N base station is not really available for download - but you can get it if you are up to following this procedure:
1. download "AirPort Base Station Update 2007-002 for Windows" from Apple's web site
2. use a Winzip utility to extract the contents of the file you downloaded (called Airport521update.exe) to another folder.
3. the contents of that folder should include four files - applesoftwareupdate.msi, apsetup.msi, apsetupadmin.exe, and bonjour.msi
4. go to All Programs -> Accessories. Right click on the "Command Prompt", select to "run as administrator", and click continue when Windows asks for your permission to run this command.
5. in the command prompt window, type and execute the command
msiexec /i pathto_folder_of_files_youdownloaded\apsetup.msi /qb ap50isinstalled=1
This method simply forces the installer into thinking Airport 5.0 is already installed, thus letting the installer complete its job of installing a full working copy of the updated version.
This procedure also installs Bonjour for Windows, which will simplify the task of configuring on the PC any printer connected to the Base Station.

HT1145 The airport extreme used with my iMac is not seeing my other devices...anybody, please?

The airport extreme used with my iMac is not seeing my iPhone 5, iPad (third generation) or my windows based PC. When I open the airport utility it shows only the internet and my iMac. It does not identify the others. Any thoughts? Thanks

Hi DaileyT,
Thanks for using Apple Support Communities.
For more information on this, take a look at this article:
When do Apple wireless devices appear in AirPort Utility?
http://support.apple.com/kb/HT3624
Troubleshooting missing devices
If your Apple wireless device doesn't show up in the wireless device list, try the following:
Check to see that the device is turned on.
Check that the device is connected to the network via Ethernet or in wireless range of your computer.
Make sure the device has had adequate time to start up and become discoverable. In the case of Apple wireless devices that are not connected via Ethernet, AirPort Utility scans for new devices once every 15 seconds. From the time a device becomes discoverable (typically around one minute), it could take up to another 15 seconds before the device is displayed in the list.
If you have just configured a new Apple Wireless device, upgraded the firmware, selected "Restore Default Settings..." or have hard reset and configured an Apple wireless device and it does not show up in AirPort Utility after restarting, you may have an incorrect setting. You may want to hard reset the unit and set it up again.
If you are connected to a specific wireless network, all Apple wireless devices which make up that network will appear. However, if you "Restore Default Settings..." from AirPort Utility, or hard reset a device that is out of physical wireless range of the computer, you will need to move the device closer the computer to configure it again.
Best of luck,
Mario

HT4259 Is it still possible to configure an AirPort Extreme as a Wireless/Ethernet bridge?

Hi,
I have a 4th generation 3TB Time Capsule as my primary wireless device. I have tried configuring my 4th gen AirPort Extreme as a bridge (passive wireless to Ethernet bridge, not active wireless router) and despite two firmware resets, am unable to do so with either Airport Utility 6.1 or 5.6.1. I am using a retina MacBook Pro with 10.8.2 to run the Airport Utility. I know this used to work with earlier versions of the AirPort Extreme firmware (currently 7.6.1 for both devices) and earlier versions of the Airport Utility, because I have done it before and it has worked fine, although I haven't tried this for more than 3 years. Is it still possible to do this, or am I missing something?

If you are correct about not being able to configure the Extreme as a bridge then I guess I'm stuck with running the Extreme in extend mode.
We only answer questions when we've tested it ourselves. But, you can prove to yourself that the AirPort Extreme cannot act as a simple wireless to Ethernet bridge by trying to configure it to "join" a wireless network. You will see that the Ethernet ports are not enabled in this type of setup.
Configuring the AirPort Extreme to "extend" a wireless network will enable the Ethernet ports. I'm sure that you understand that although the Extreme has Gigabit Ethernet ports, the "Ethernet" signal that appears at the LAN ports will only be as fast as the wireless connection to the AirPort Extreme allows.
Perhaps surprisingly, the best that Cisco has to offer in terms of a wireless to Ethernet bridge is an 802.11b/g device with 100 Mbps Ethernet ports. Netgear does a bit better at least offering 802.11n capability, but still 100 Mbps ports.
The AirPort adapter or a USB wireless adapter might be the simplest way to go if you are concerned about adding an additional wireless access point. Good luck.

How do I configure an Airport Extreme base station to receive and distribute a wi-fi network from a broadband wireless router?

I have recenly upgraded my broadband service and now have a wireless router. My old network configuration was a router connected by ethernet cable to an Airport Extreme base station which then broadcast my wireless network (I also had an Airport Express base staion set up as a wi-fi booster elswhere in the house).
I now have two networks (my original network and the new network from the wireless router) and wish to amalgamate these into one.
Ideally I wish to use the Airport Extreme base station as the "remote" booster (I have purchased Powerline adapters for this purpose) but don't know how to configure the Airport Extreme base station in order to to this.
Can you advise on the best set up for this please?
My Mac is running OS X 10.8.2 and the Aiport untility is version 6.1.
Thanks in anticipation.

The AirPort Extreme should be configured to "create a wireless network" with the same WiFi network name, security type (usually WPA2 Personal) and password as your existing router. It should be configured as connection type Ethernet and be in bridge mode.

Convert word document in PDF,e pub,by using third party dll in Sharepoint designer workflow 2013?

Hi,
I want to convert word document to PDF, EPub, by using third party (.dll).
In SharePoint designer workflow in 2013.
So that I have question, Can we Install third party (.dll) in SharePoint workflow Designer for conversion?
Means I have created one simple application conversion of word to e Pub, PDF, Image by using (Spire.doc dll) in Visual Studio.
So this same conversion I want to work in SharePoint designer workflows?
So anybody has any solution then please provide me.
Thanks,
Samadhan

it might be worth looking at these CodePlex steps, that plug directly into the Word Automation Services.
http://sp2010wordautomation.codeplex.com/
It'll provide you with a configurable step like the below that should help you achieve your aims
Steven Andrews
SharePoint Business Analyst: LiveNation Entertainment
Blog: baron72.wordpress.com
Twitter: Follow @backpackerd00d
My Wiki Articles:
CodePlex Corner Series
Please remember to mark your question as "answered" if this solves (or helps) your problem.

Using third party jars with Oracle Business Rules

Hi
I am working on Oracle AS 10g release 2.
We are using Oracle Business Rules in integration with Oracle BPEL.
While using third party jars however, Oracle Business Rules end is facing errors.
Error during unmarshallingProvider com.sun.xml.bind.ContextFactory_1_0_1 not found
oracle.classloader.util.AnnotatedClassNotFoundException:
Missing class: com.sun.xml.bind.ContextFactory_1_0_1
Dependent class: javax.xml.bind.ContextFinder
Loader: oracle.xml:10.1.0_2
Code-Source: /D:/oracleasr3/lib/xml.jar
Configuration: <code-source> (ignore manifest Class-Path) in META-INF/boot.xml in D:\oracleasr3\j2ee\home\oc4j.jar
Can anybody help in figuring out where Jaxb jars(3rd party jars) are to be kept so that OAS access it?
We tried using the applib folder to load the jars but we are getting class loading errors.
When new instances are created, class loading is not happening.
Pls help.
Thanks
Kavya

Are you using Application Server Release 3 or Release 2? There are different versions listed in your mail.
I think you probably want to add this as a shared library via EM and then import the shared library to your application with the application's xml config files.

How to configure the airport extreme as wireless bridge?

how can i configiure the airport to function as a wireless bridge?
i have connected my airport now with a wire to the modem/router delivered by the local internetprovider (THomson DWG850).
Since this device has not much reach I want to connect the airport extreme wireless and position in the living room to have better reach?
or do i need toc hang the settings in the Thomson? does anyone know where to find the admin password of the Thomson?
thanks in advance
Eric

how can i configiure the airport to function as a wireless bridge?
Sorry, but it is not possible to configure the AirPort Extreme for this type of setup. You will need to connect the AirPort Extreme to the Thomson router using an Ethernet connection.
does anyone know where to find the admin password of the Thomson?
Google turned this up in 5 seconds. There may be others if you look.
Thomson default passwords

Airport Extreme used to extend network malfunctioning

For several years I have had a modem with a current generation AE used for wireless and an older AE used to extend that wireless network. The configuration that has worked for me has been to set the first AE in bridge mode and use the second to extend the first AE. All are connected via ethernet. It has always worked...until recently.
I found that when I unplug both my AEs and turn the wireless portion of my modem on to help with testing (it was usually off), my problems (drastic latency, drops, etc...) went away. The modem alone seems to work as it should. I decided to set up my network from scratch to see if that would help. It has not and I wanted to get some expert advice.
Here are my steps and the issues.
1. I shut everything down and only turn the modem back on. I test the signal via the wireless and it works fine every time.
2. I reset the current generation AE and begin to set it up. I configure the AE to be in bridge mode. As soon as the modem updates, the network has gone down the tubes - nothing works. Internet access is poor or unavailable from the AE and modem. If I unplug the AE, I'm back up and running from the modem with no issues.
3. I am not even trying to use the 2nd
Current AE firmware is 6.3.4
MBP release 10.10.2
Any help would be appreciated?

You should be using the setup "wizard" to configure the AirPort Extreme. Are you doing this? You should not have to set up the AirPort in Bridge Mode....the setup utility will do that for you automatically, assuming that everything is working.
Try the setup again using the "wizard". If you are still having problems after a few tries, then try the "other" AirPort Extreme temporarily.
If the "other" AirPort works, you may have a defective AirPort Extreme.

Configuration of AirPort Extreme Using Third Party LAN Ethernet Adapter?

Similar Messages

Maybe you are looking for