Configuration of saprouter.
Hello,
I have reinstalled the saprouter but after configuring the saprouter, it's giving error while starting saprouter.
The error is as follows :
$ ./saprouter -l
SAP Network Interface Router, Version 40.4
***LOG Q0I=> NiPGetHostByName: 'localhost' not found: getaddrinfo [niuxi.c 1759]
*** ERROR => NiGetLoopbackAddr: NiIGetNodeAddr failed (rc=-2) [nixx.c 2179]
Mon Jun 16 16:53:40 2014
peer SAProuter with NI version 40 ...
send info-request to running SAProuter ...
SAP Network Interface Router running on port 3299 (PID = 132)
Started on: Mon Jun 16 16:12:14 2014
ID CLIENT | PARTNER service
-----------------------------------+---------------------------------------
9 127.0.0.1 | (no partner)
Total no. of clients: 1
Working directory : /usr/sap/saprouter
Routtab : ./saprouttab
Please help.
Hi,
I have configured SAP Router on Windows. When i start the router i am getting error like as below.
trcfile dev_rout
ERROR SNC processing failed:
SncInit
TIME Tue Sep 30 10:32:29 2008
RELEASE 700
COMPONENT NI (network interface)
VERSION 38
RC -17
MODULE nisnc.c
LINE 646
DETAIL NiSncInit: sncrc=-1
COUNTER 3
Please any body give the solution.
Thanks,
Regards,
venkat
Similar Messages
-
hello gurus
i need to connect to sap using vpn.i have configured the sap router abnd it seems to be working.I recieved the connection details from sap with deatils at SAP site,Encryption,preshared secrect.
So now i have checked the next step where i will have to input the preshared key but no luck .I have looked at note 486688 but there is a section where it refers to see Notes 17285 and 29784 but those are said to be internal notes
Maybe i need a step by step guide on how to configure the connection once the saprouter has been installed.
any ideas will be welcomeHello,
I think you are confusing SNC and VPN.
You use saprouter to control access to/from your sap systems and sap.
To encrypt the traffic (over the Internet) between your saprouter and the saprouter at SAP, you use either:
VPN - a firewall/vpn device (hardware and/or software) provided by third party (e.g. Check Point, Cisco devices)
OR
SNC - a software solution to encrypt traffic provided by saprouter
If you setup a VPN connection with SAP, you need to configure a VPN connection on your firewall as specified by SAP. This is where you need the shared secret.
When using VPN, your traffic is encrypted and you do not need SNC.
When you don't use a VPN connection, your saprouter communicates directly to the saprouter at SAP. To protect this traffic, which is sent in clear text over the Internet, you should encrypt this traffic. If you have no friewall or VPN device, you can use SNC to encrypt the traffic.
In this case, you need to request a certificate for your saprouter and configure the saprouter for SNC.
Note 486688 describes the requirements for a VPN connection and clearly states you need a VPN/IPSec-enabled router/firewall and a public IP-address for both your router/firewall and your saprouter.
I hope this makes things a bit more clear.
Kind regards,
Dagwin -
Business Objects Enterprise and Data Services and SAPRouter
Hi,
I am relatively new to Business Objects so I am not entirely sure how this works. My question is can Business Objects Enterprise and Data Services be configured in SAPRouter for SAP to dial in and access the systems.
Regards
NaureenHi,
I am new to PI Upgradtion Project.
We are planning to upgrade PI 7.11 to PI 7.3.
Can you please help me what are the steps we have to fallow to upgdrade PI and what are the changes/Issues will happen when upgradtion in PI.
Share me your ideasssssssssssssssssss.......
Thanks,
Mallam -
Saprouter - Host did not respond times
Hello,
We have configured the saprouter with a VPN, the test connection in SM59 is OK.
When I try to start "R/3 Support" in SAP Support Portal, the SAP Service Connector gives me the message: "The service connection has been opened successfully." but SAPRouter status does not get "connect", it keeps on "Host did not respond x times".
How can I find the problem? If the SAP Connector shows me "The service connection has been opened successfully."?
RegardsHi Richard
1. Is it new SAProuter installed or already working one?
2. In which OS? could you refer the SAP links
Installing the SAProuter - SAProuter - SAP Library
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/c06c8846-c160-2d10-d18e-d9961e9c7219?QuickLink=index&…
BR
SS -
SAProuter string in SAPlogon pad
Hi Team,
I have read the posts and followed the steps for configuring the saprouter entry in the SAPGui. For some reasons, I am just not able to connect to my SAP system thru the SAPgui. These are the details of our connection
SAProuter is installed as service on our SAP Dev box (windows 2003)
Public ip - 66.147.170.102
This public ip is NAT to the local SAP DEV box 192.168.101.4 where the saprouter is installed.
This is the saprouttab entry
#SNC-connection from and to SAP
KT "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 194.39.131.34
#SNC-connection from SAP to local R/3 system for support
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.168.101.4
3200
#Access from local network to SAPNet - R/3 Frontend
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" * *
P * 194.39.131.34 3299 password
D * * *
Can someone please give me the exact string that should be put in the SAPgui.
Thanks for your help
VishalHi Joe,
Thanks for your quick reply.
My objective is to come in from the internet without using the office VPN or network.
My saprouter is working fine, as SAP can login to our systems.
Now I want to set something thru which any person who wants to access our SAP system can do so without getting into our VPN or network. Basically people in Sales when they are at the customer sites.
The NAT is completed so that does not seem an issue.
I tried using the /H/public ip/H of our saprouter connection, but its not working. Also tried introducing a password in the saprouttab, restarted the service, and then tried with the W parameter, but did not work.
Normally what would be the string if I have to enter it in the SAPlogon.
Thanks,
Vishal -
SNC Processing Failed starting the SAProuter
Dear Experts,
i have finished the configuration of SAProuter, while running the router i am getting the error "SNC Processing Failed." here may dev_rout file is
The command that i'm using is:
D:\usr\sap\saprouter>saprouter.exe -r -S 3299 -K "p:CN=SSAP00001PBBI, OU=0000893
577, OU=SAProuter, O=SAP, C=DE"
trc file: "dev_rout", trc level: 1, release: "700"
* ERROR SNC processing failed:
* sncInit
* TIME Thu Sep 25 10:40:38 2008
* RELEASE 700
* COMPONENT NI <network interface>
* VERSION 38
* RC -17
* MODULE nisnc.c
* LINE 646
* DETAIL NiSncInit: sncrc=-1
* counter 3
What is the error here?
Thanks a lot
Edited by: Daniel Humberto Ramirez on Sep 25, 2008 6:31 PMHi, this is the dev_rout file,
Thanks a lot!!!.
trc file: "dev_rout", trc level: 1, release: "700"
Mon Sep 29 09:01:29 2008
SAP Network Interface Router, Version 38.10
command line arg 0: saprouter.exe
command line arg 1: -r
command line arg 2: -S
command line arg 3: 3299
command line arg 4: -K
command line arg 5: p:CN=SSAP00001PBBI, OU=0000893577, OU=SAProuter, O=SAP, C=DE
SncInit(): Initializing Secure Network Communication (SNC)
PC with Windows NT (mt,ascii,SAP_UC/size_t/void* = 16/64/64)
SncInit(): Trying environment variable SNC_LIB as a
gssapi library name: "D:\usr\sap\saprouter\ntintel\sapcrypto.dll".
Mon Sep 29 09:01:30 2008
ERROR => DlLoadLib: LoadLibrary(D:\usr\sap\saprouter\ntintel\sapcrypto.dll) Error 193 [dlnt.c 237]
ERROR => SncPDLInit(): DlLoadLib("D:\usr\sap\saprouter\ntintel\sapcrypto.dll")=DLENOACCESS
[sncxxdl.0340]*** ERROR => SncPDLInit()==SNCERR_INIT, Adapter (#0) D:\usr\sap\saprouter\ntintel\sapcrypto.dll not loaded
[sncxxdl.0604]<<- SncInit()==SNCERR_INIT
sec_avail = "false"
ERROR => NiSncInit: SncInit failed (rc=-1) [nisnc.c 647]
ERROR => main: NiSncInit failed (rc=-17) [nirout.cpp 1219]
ERROR SNC processing failed:
SncInit
TIME Mon Sep 29 09:01:30 2008
RELEASE 700
COMPONENT NI (network interface)
VERSION 38
RC -17
MODULE nisnc.c
LINE 646
DETAIL NiSncInit: sncrc=-1
COUNTER 3
<<- ERROR: SncDone()==SNCERR_INIT_FIRST -
SAProuter..Connection timed out ?
Dear Experts,
I have configured my saprouter and its working fine (as from test niping). Now i am trying to logon to the OSS of sabserv7, It desplyes first message "Unable to connect to the SAPNet message server, default connection will be use" and after a connect atempt, it displayed "Connection to host 194.39.134.35, service SAPDB99 timed out.
Please help me as i have connected directly to the internet (the computer is conneted to internet without behind any firewall).
1 - Is there anydata should be maintained in the service.sap.com?(we didnt maintained regarding connection at sap service portel.
2 - Is there any step missing?
3 - Are these system generated IP address of SAProuter are correct?
Thanks
Usman RanaYou are welcome. For the developer access key, you'll need to go to http://service.sap.com -> Keys & Requests -> SSCR Keys -> Register SSCR keys. Here, you will see your systems registered with SAP. You can select the relevant system, provide it with the details required such as Object type and ID. A key will be generated which can be used to modify the code.
For documentation on the standard modification process, please check out <a href="http://help.sap.com/saphelp_nw2004s/helpdata/en/60/d6ba5aceda11d1953a0000e82de14a/content.htm">this link</a>.
Please keep in mind that in case of modifications, whenever you will install latest patches, your modified programs may be overwritten by newer SAP releases and you'll have to adjust these programs manually once again. That is why modifications are not recommended and the developers should try to find a suitable user exit to write their code into. If no user exit exists, then it is recommended to try to find a workaround such as trying to carry out the chages by using a function module/batch input/etc after the standard transaction is complete. Modifications should only be the last resort and someone experienced should confirm if that is the only option available. If your developer needs further information, (s)he should post a question in any of the forums listed at /community [original link is broken] .
Hope this helps.
Regards
Shehryar
ps: Yes, I am the guy from Abacus Consulting -
Solution manager Remote Connection issues
Hi
I'm currently in the process of setting up Solution Manager 7.1 on windows Server 2008r2 using central system.
I did the prerequisite check & the Solman installation and i'm actuallly working on the post-installation steps.
I'm experiencing difficulty with the step : "Configure Remote Connection to SAP".
I followed the informations provided on : http://service.sap.com/remoteconnection
In the technical prerequesite you have to set up a connection to sap support.
So i have to choose a connection type : I selected Internet connection so my first question is : do we need "VPN with SNC" or "VPN OR SNC" ?
I personnaly understood VPN or SNC.
So from here i decided to use SNC.
The first step was to set up & configure the SAProuter. I decided to do it on an another computer on the same domain ( not on the same computer where Solution Manager is installed ) but i'm not sure it is necesary
I assume I can install Saprouter on the same location as the Solution manager? do you recommend it ?
The Basic Functions testing with niping is working.
The next step is : "establish Internet Connections"
So now i can choose between SNC or VPN : my goal is to establish the connection as fast as possible.
I actually don't have a switch available ( i can get one if necesary but time is running ... ) so i'm opting for the SNC solution.
I tryed to get the certificate for the saprouter but i don't have a register SAProuter, but when i opened a customer messager for component XX-SER-NET, SAP answered about the impossibility to access SAP service Backbone with an SNC , saying that i will need to register a VPN site to site connection to SAP => i don't get it .... Can someone explain it to me ?
So please can one of you guru's tell me how to set this remote connection :
-which materials ( server / switch / firewalls ) ?
-where to get the right documentation ?
-What about DMZ ?
-I have a single IP Address is that enough ? ( setting up nat for port 3299 )
- do i have to contact a service provider ?
My idea was initially to set up the SAProuter on the same computer as the SOLMAN setup & use SNC communication to communicate with SAP but it doesn't seems that easy. Do i need separate installation for Saprouter <=> Solution Manager. ?
What's the minimal infrastructure to establish this connection ?
In addition to that, after configuring the SAProuter, i had trouble with the SAPMMC : on my system , on the instance 0 , the process disp+work.EXE won't run ( yellow light )and i can't find where i made a mistake if you have suggestions ...
Really need your help, i'm on a short deadline ... Any help, even incomplete, would be appreciated.
Thanks a lot.Thx for the answer.
I actually managed to register my saprouter with SAP and was granted with CN/OU & connection informations.
I followed this guide : http://service.sap.com/saprouter-sncdoc with the addition of this guide : http://wiki.sdn.sap.com/wiki/display/Basis/SAProuterviaSNC.
My first issue : I'm running with a Windows server 2008 r2 enterprise edition 64 bits with a processor Intel Xeon 2.4ghz ( dualcore). so i decided to use the crypto folder "nt-x86_64"
For the environment variable i set as System variables SECUDIR = C:\usr\sap\saprouter and SNC_LIB = C:\usr\sap\saprouter\nt-x86_64\sapcrypto.dll
The generation/install of the certificate is alright ( sapgenpse get_my_name -v -n Issuer is OK )
using the command :saprouter -r -K "p:CN=mycn, OU=myOUnbr, OU=SAProuter, O=SAP, C=DE" i have
I get the following message : trc file dev_rout
no ligging active
Its strange cause it looks like its running but when i check the services running on windows saprouter isn't started .... How to know if SAProuter is running right ?
If i folow the SAP procedure : Step 3 : test of the ip connection by the customer : SAP Remote Services : technical preparation ( see SAP Note 812386 ) : it's ask in the note to implement note 766505 via SNOTE : i get the following error msg : Error in remote connection to destination SAPOSS : Error when opening an RFC connection ( LB: Hostname or service of the message server unknown#DEST = SA
What's wrong ?
If i use T oss1 in parameter => technical setting => i set my saprouter info in SAProuter 1 ( at customer site ) with instance no. 99 and if SAProuter and SAPNet Message Server at SAP i put the following : Name : sapserv2 / IP Address 194.39.131.34 intance no. 99 and message server name oss001/ DB Name 001/ Instance no.01.
When trying to "Logon to SAPNet" i have an error Unable to connect to SAPNet message server ( default connection will be used ... )
and followed by the error screen : "partner '80.15.173.168:sapdp99' not reached WSAECONNREFUSED : Connection refused. do you want to see the detailed error description ? "
Details : module nixxi.cpp / line 3286 / Method : NipConnect2:80.15.173.168:3299 / Return code : -10 / System call : connect / Error No : 10061 / Error Text WSAECONNREFUSED: Connection refused / Counter : 10
Any idea ?
when doing niping.exe -c -H /H/mylocalSR/H/194.39.131.34/H/194/39.131.34 i obtain :
Wed Dec 07 21:20:09 2011
connect to server o.k
Wed Dec 07 21:20:09 2011
send and receive 10 messages (len 1000)
times -
avg 122.148 ms
max 193.731 ms
min 81.564 ms
tr 15.990 kB/s
excluding max and min :
av2 118.273 ms
tr2 16.514 kB/s
Is it the expected output ?
I've maintained system data in service.sap.com/system-data ( selecting the sap router ) then i tryed to use the SAP service connection, downloaded the .exe but i can't find the stfk.oez. I realized that in my maintain connection screen i have no space for entering any routestring. Seems wrong ?
Do i have to use the SAO?
i've made nat redirection from my router as this : from my public ip to my lan ip ( 192.168.x.x) what should i enter in the routestring : /H/public or lan or hostname ?/S/3299 ?
Hoping you can help me ! ( the goal of all this is to set up RFC connection for postinst step of Solution manager ).
Edited by: BLANCHARD Guillaume on Dec 7, 2011 10:47 PM -
SAP Implementation Process !!!
Hi Folks,
I need brief information about the SAP implementation process. As per the ASAP Methodology we have different phases involved in the entire implementation process from Project preparation,Blue print analysis,Realization,Final Preparation and Go Live Support.
I did not involve myself into implementation. Being a Basis consultant I would like to know what is the involvement of basis consultant in each phase in detail and what are the activities being carry out by a basis team, what would be the avg team size and what would be the duration of the project approximately. I know it depends on the project and modules being used,architecture and all. i just wanted to know the rough details for information.
I would really appreciate for any useful information.
Regards,
VinodHi Viond,
Please find below an elaborated details for SAP Implementaion.
The ASAP (Accelerated SAP) Roadmap provides the methodology for implementing and continuously optimizing your SAP System. It divides the implementation process into five major phases and offers detailed Project Plans to assist you (Microsoft Project format). The documentation stored at each level of the Roadmap tree structure contains recommendations on implementing your SAP System and links to helpful tools and accelerators. We use SAP Solution Manager for the same and define the steps and this information can be transformed into MPP.
The implementation of your SAP System covers the following major phases:
Project Preparation
In this phase you plan your project and lay the foundations for successful implementation. It is at this stage that you make the strategic decisions crucial to your project:
Define your project goals and objectives
Clarify the scope of your implementation
Define your project schedule, budget plan, and implementation sequence
Establish the project organization and relevant committees and assign resources
Sizing for the SAP Servers (SAPS) Important for Basis.
Business Blueprint
In this phase you create a blueprint using the Question & Answer database (Q&Adb) older versions and now it has been replaced by new value adds from SAP in Solution Manager, which documents your enterpriseu2019s requirements and establishes how your business processes and organizational structure are to be represented in the SAP System. You also refine the original project goals and objectives and revise the overall project schedule in this phase. In short its As is >> To be its from from functional consultant (mapping of business process) Basis will be involved how and when backup will be taken what 3rd party/vendor will be used, how users will be handled (CUA or normal procedure).
Realization
In this phase, you configure the requirements contained in the Business Blueprint. Baseline configuration (major scope) is followed by final configuration (remaining scope), which can consist of up to four cycles. Other key focal areas of this phase are conducting integration tests and drawing up end user documentation. Major part will be creation of transport requests and transportation to QAS system. Configuration of SAProuter, Solution manager and its various configuration
Final Preparation
In this phase you complete your preparations, including testing, end user training, system management, and cutover activities. You also need to resolve all open issues in this phase. At this stage you need to ensure that all the prerequisites for your system to go live have been fulfilled...Final Check.
Go Live & Support
In this phase you move from a pre-production environment to the live system. The most important elements include setting up production support, monitoring system transactions, and optimizing overall system performance.
You can also download an HTML version of the ASAP Core Roadmap 7.1 on [SAP Services Marketplace - ASAP Roadmaps and Run SAP Roadmaps|http://service.sap.com/asap] (SMP login required).
All the best ! -
Test conn. SAPOSS error when opening an RFC connection SNC processing fail
Dear all,
I configured a Saprouter in DMZ with SNC connection type to establish connection from my company to SAP and vice-versa. Also I accept connection from external company to our SAP systems. During the test in SM59 SAPOSS connection I receive the following error:
Logon Errore di colleg.
Dettagli err. Error when opening an RFC connection
Dettagli err. ERROR: SNC processing failed: SncSessionInitiatorAK
Dettagli err. LOCAZ.: SAProuter 39.1 (SP3) on 'srvsaprouter1'
Dettagli err. DETT.: NiSncIInitHdlSecurity: sncrc=-4;0x9d9350
Dettagli err. COMPONENT: NI (network interface)
Dettagli err. CONTAT.: 209
Dettagli err. MODULE: nisnc.c
Dettagli err. RIGA: 1091
Dettagli err. VALORE RIT.: -104
Dettagli err. SUBRC: 0
Dettagli err. RELEASE: 710
Dettagli err. ORA: Fri Jul 17 11:01:22 2009
Dettagli err. VERS.: 39
My saprouttab for SAP AG connection is the following:
#SNC-connection from and to SAP
#KT "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" * *
KT "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 194.39.131.34 *
SNC-connection from SAP to local R/3-System for Support
#KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" * *
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.229 3200
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.229 3201
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.211 3200
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.211 3600
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.209 3200
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.210 3201
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.231 3200
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.231 50000
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" epe0s.calpeda.priv 50000
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" epe0sc.calpeda.priv 50000
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.242 3200
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.242 50000
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" epe0t.calpeda.priv 50000
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" epe0tc.calpeda.priv 50000
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.215 3200
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.101.111.215 50100
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" epe0p.calpeda.priv 50100
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" epe0pc.calpeda.priv 50100
SNC-connection from SAP to local R/3-System for NetMeeting, if it is needed
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" * 1503
SNC-connection from SAP to local R/3-System for saptelnet, if it is needed
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" * 23
Access from the local Network to SAPNet - R/3 Frontend (OSS)
#P <IP-addess of a local PC> 194.39.131.34 3299
P * * *
P * 194.39.131.34 3299
D * * *
Any suggestions?
Thanks in advance.SNC processing failed could mean lots of things... did you installed the SAPcrypto library?.. did you created the certificates correctly?...
Read SAP notes 812386 and 33135.
Regards
Juan -
Hi Guys,
I just installing and configured the saprouter in our system, when I'd registered the server SID in OSS, they gave me this IP which is not our internal or external IP.What's this IP for actually? Do I need to put it in my saprouttab coz right now I open the connection from OSS (Host did not respond X times).
TQHi,
I just configured my saprouter and everything went okay, even the OSS1 is working but when i open the connection in the OSS (service.sap.com), the connection is open for about 8 minutes but then its lost connection (yellow).Was there something missing here? I already put the outbound connection (KT "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 194.39.131.34 *) and our server (KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" <my SAP router> *) in my saprouttab. Here the recent log from devrout :
trc file: "dev_rout", trc level: 3, release: "700"
Tue Jan 15 11:33:53 2008
NiHsLInit: alloc host/serv bufs (200/200 entries)
NiIInit: allocated nitab (811 at 00280048)
NiIInit: host/serv bufs already initialized
NiPGetNodeAddrList: got 1 interface(s) from operating system
[0] IP-Address: 192.168.1.220
NiIGetServNo: servicename '3299' = port 0C.E3/3299
SAP Network Interface Router, Version 38.10
Compiled Sep 27 2007 01:16:41
command line arg 0: d:\usr\sap\saprouter\saprouter.exe
command line arg 1: -r
command line arg 2: -R
command line arg 3: d:\usr\sap\saprouter\saprouttab
command line arg 4: -S
command line arg 5: 3299
command line arg 6: -K
command line arg 7: p:CN=vantage01, OU=0000336743, OU=SAProuter, O=SAP, C=DE
command line arg 8: -V3
service : 3299
routtab : d:\usr\sap\saprouter\saprouttab
plug-in : no plug-in
-argument: 'no argument'
clients : 800
max servers : 1
quelength : 1
maxheap : 20000000
timeoutL : 5000
tracefile : dev_rout
logfile : no logging active
portrange : no portrange active
local address : default address
->> SncInit(prg=0, ini_fname=(NULL), &sec_avail=01D1FF1B)
SncInit(): Initializing Secure Network Communication (SNC)
PC with Windows NT (mt,ascii,SAP_UC/size_t/void* = 8/32/32)
SncInit(): Trying environment variable SNC_LIB as a
gssapi library name: "D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll".
load shared library (D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll), hdl 0
using "D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll"
DlLoadFunc: GetProcAddress(sapsnc_init_adapter) Error 127
Error 127 = "The specified procedure could not be found."
load shared func (gss_acquire_cred) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_release_cred) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_init_sec_context) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_accept_sec_context) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_process_context_token) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_delete_sec_context) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_context_time) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_get_mic) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_verify_mic) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_wrap) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_unwrap) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_display_status) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_indicate_mechs) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_compare_name) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_display_name) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_import_name) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_release_name) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_release_buffer) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_release_oid_set) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_inquire_cred) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_add_cred) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_inquire_cred_by_mech) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_inquire_context) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_wrap_size_limit) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_export_sec_context) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_import_sec_context) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_create_empty_oid_set) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_add_oid_set_member) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_test_oid_set_member) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_inquire_names_for_mech) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_inquire_mechs_for_name) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_canonicalize_name) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_export_name) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
load shared func (gss_duplicate_name) from D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll
File "D:\usr\sap\PD1\SYS\exe\nuc\NTI386\sapcrypto.dll" dynamically loaded as GSS-API v2 library.
The internal Adapter for the loaded GSS-API mechanism identifies as:
Internal SNC-Adapter (Rev 1.0) to SECUDE 5/GSS-API v2
<<- SncPDLInit()==SAP_O_K
<<- SncInit()==SAP_O_K
sec_avail = "true"
->> SncSetMyName(snc_hdl=00000000, myname="p:CN=vantage01, OU=0000336743, OU=SAProuter, O=SAP, C=DE")
<<- SncSetMyName()==SAP_O_K
in: myname = "p:CN=vantage01, OU=0000336743, OU=SAProuter, O=SAP, C=DE"
NiBufISetParam: set max heap to 20000000
NiSetParamEx: switch NIP_CONNLOCAL off (not supported by platform)
NiIMyHostName: hostname = 'vantage01'
main: pid = 5072, ppid = 0, port = 3299, parent port = 0 (0 = parent is not a saprouter)
NiICreateHandle: hdl 0 state NI_INITIAL
NiIInitSocket: set default settings for new hdl 0 / sock 180 (I4; ST)
NiITraceByteOrder: CPU byte order: little endian, reverse network, low val .. high val
NiIBind: hdl 0 bound to 3299 (IP only)
NiIBlockMode: set blockmode for hdl 0 FALSE
NiIListen: state of hdl 0 NI_LISTEN
NiIListen: listen for client requests on hdl 0
NiSelICreateSet: new set0
SiSelNInit: allocate 134544 bytes for FI (811)
NiSelIInit: size of set0 is 811
SiSelNSet: sock 180 added to set pos 0
NiSelIAddMsg: added hdl 0 to set0
SiSelNSet: set events of sock 180 to: rp-
reading routtab: 'd:\usr\sap\saprouter\saprouttab'
<<- SncNameToAclKey_r()==SAP_O_K
in: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
'aclkey ' (addr=0023F9E8, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
NiStrToAddrMask: '194.39.131.34' -> 194.39.131.34 [ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff]
<<- SncNameToAclKey_r()==SAP_O_K
in: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
'aclkey ' (addr=0023F9E8, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
NiStrToAddrMask: '210.19.199.62' -> 210.19.199.62 [ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff]
<<- SncNameToAclKey_r()==SAP_O_K
in: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
'aclkey ' (addr=0023F9E8, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
NiStrToAddrMask: '210.19.199.62' -> 210.19.199.62 [ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff]
NiIGetServNo: servicename '3200' = port 0C.80/3200
<<- SncNameToAclKey_r()==SAP_O_K
in: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
'aclkey ' (addr=0023F9E8, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
NiStrToAddrMask: '210.19.199.62' -> 210.19.199.62 [ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff]
NiIGetServNo: servicename '3299' = port 0C.E3/3299
<<- SncNameToAclKey_r()==SAP_O_K
in: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
'aclkey ' (addr=0023F9E8, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
NiStrToAddrMask: '210.19.199.62' -> 210.19.199.62 [ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff]
NiIGetServNo: servicename '3201' = port 0C.81/3201
NiStrToAddrMask: '194.39.131.34' -> 194.39.131.34 [ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff]
NiIGetServNo: servicename '3299' = port 0C.E3/3299
contents of routtab ('d:\usr\sap\saprouter\saprouttab', 7 entries):
KT,<<- SncAclKeyToName()==SAP_O_K
'aclkey ' (addr=002DD8E0, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
out: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
p:CN=sapserv2, OU=SAProuter, O= 194.39.131.34 ffff:ffff:ffff: * *
KP,<<- SncAclKeyToName()==SAP_O_K
'aclkey ' (addr=002DDD48, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
out: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
p:CN=sapserv2, OU=SAProuter, O= 210.19.199.62 ffff:ffff:ffff: * *
KP,<<- SncAclKeyToName()==SAP_O_K
'aclkey ' (addr=002DE1B0, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
out: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
p:CN=sapserv2, OU=SAProuter, O= 210.19.199.62 ffff:ffff:ffff: 3200 *
KP,<<- SncAclKeyToName()==SAP_O_K
'aclkey ' (addr=002DE618, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
out: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
p:CN=sapserv2, OU=SAProuter, O= 210.19.199.62 ffff:ffff:ffff: 3299 *
KP,<<- SncAclKeyToName()==SAP_O_K
'aclkey ' (addr=002DEA80, len=86) full hexdump
0x00000 00030401 00080606 2b240301 25010000 ........ +$..%...
0x00010 00443042 310b3009 06035504 06130244 .D0B1.0. ..U....D
0x00020 45310c30 0a060355 040a1303 53415031 E1.0...U ....SAP1
0x00030 12301006 0355040b 13095341 50726f75 .0...U.. ..SAProu
0x00040 74657231 11300f06 03550403 13087361 ter1.0.. .U....sa
0x00050 70736572 7632 pserv2
out: name = "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE"
p:CN=sapserv2, OU=SAProuter, O= 210.19.199.62 ffff:ffff:ffff: 3201 *
P, 0:0:0:0:0:0:0:0 0:0:0:0:0:0:0:0 194.39.131.34 ffff:ffff:ffff: 3299 *
D, 0:0:0:0:0:0:0:0 0:0:0:0:0:0:0:0 0:0:0:0:0:0:0:0 0:0:0:0:0:0:0:0 * *
NI-ROUTER LOOP ********
SiSelNSelect: start select (timeout=-1) -
Resume for Freshers in SAP Basis
Dear Friends,
I Fresher in SAB Basis. I was finished the course in june 2010. I am doing the practices from june to till date on SAP IDES 4.7 and ECC6.0.
Please send the resume format for fresher.
Regards
akhileshAkhil,
I dont think so you will get an answer here .... but at the same time all I can say you can add those activities which you have learnt and mastered the Basis Activities.
Batch Job Creation
Checking System Logs
Analyzing Ssytem Dumps
Back up/Archive logs Monitoring
Configuration of SAProuter
Installation of ECC and other SAP Components
Configuring SMSY and LMDB (Solution Manager)
thats the way you create your CV and dont put anything which you have not done...
Hope it will help you. -
Hello everybody,
I have configure the SAProuter on windows 2008. Now when i test a connection to OSS then it generate the following error
Logon : Connection Error
Error Details : Error when opening an RFC connection
Error Details : ERROR: SNC processing failed: SncProcessInput
Error Details : LOCATION: SAProuter 39.2 (SP4) on 'sapserv2a'
Error Details : DETAIL: NiSncIProcIn: sncrc=-4;8000000100495ae0
Error Details : COMPONENT: NI (network interface)
Error Details : COUNTER: 21
Error Details : MODULE: nisnc.c
Error Details : LINE: 946
Error Details : RETURN CODE: -93
Error Details : SUBRC: 0
Error Details : RELEASE: 710
Error Details : TIME: Tue Aug 11 07:39:17 2009
Error Details : VERSION: 39
So please suggest me how to solve the problem or what entry should be maintain in the saprouttab file.
Thanks
GaneshHello everybody,
I had again re-configure SAPRouter but it gave the following errors
settings in OSS1 as follows
saprouter1
Name - xyz
IP address - a.b.c.d
saprouter at SAP SAPNet message server
Name :- sapserv2 Name : oss001
IP :- 194.39.131.34 DB name : o01
Instnac no : 01
When i am going to log on it gives the error message
sapserv2a:router permission denied(a.b.c.d to ossoo1,sapdp01)
and when RFC testing for OSS by SM59, it gave the error
Logon :Connection Error
Error Details :Error when opening an RFC connection
Error Details :ERROR: partner 'a.b.c.d:sapdp99' not reached
Error Details :LOCATION: SAP-Server devsrv_DEV_00 on host devsrv (wp 0)
Error Details :DETAIL: NiPConnect2
Error Details :CALL: connect
Error Details :COMPONENT: NI (network interface)
Error Details :COUNTER: 3
Error Details :ERROR NUMBER: 10065
Error Details :ERROR TEXT: WSAEHOSTUNREACH: No route to host
Error Details :MODULE: nixxi.cpp
Error Details :LINE: 2823
Error Details :RETURN CODE: -10
Error Details :SUBRC: 0
Error Details :RELEASE: 700
Error Details :TIME: Wed Aug 12 14:16:27 2009
Error Details :VERSION: 38
so please suggest me how to solve the problem?
thanks
Ganesh
Edited by: ganesh borase on Aug 12, 2009 10:48 AM -
Hi,
I need to raise network security in SAP systems.
We already have SAP ERP systems and they all hidden behind saprouter in other subnet.
But what about SAP BO?
SAP BI platform server, FC, Intercompany, FIM, DataServices, BPC - I want to move these system to another subnet and hide behind Webdispatcher + saprouter.
Anyone have tried to do so? Or please offer other variants.
Thanks...Hi,
These links can help you:
HTTP Based tools
https://service.sap.com/sap/support/notes/1787981
WTS
https://service.sap.com/sap/support/notes/605795
If you encounter an issue with the install or configuration of SAPRouter.
A ticket can be created under (or transferred to) CSS component: XX-SER-NET-HTL.
Best regards,
Siwar -
Security Issues for Remote Login to ECC Server
Hi,
I have configured the saprouter so that people can remotely access the SAP ECC Servers outside the local area network. The saprouttab file contains the following entry:
P * * *
The parameter login/no_automatic_user_sapstar has also been set to a value 1.
The user DDIC and SAP* can only be accessed using the master password, which is provided at installation time.
Is my network secure enough? Or do I need to take into account some more steps / measures?
Regards.Hello,
Generally its not recommended to open up your network in the manner you have mentioned, however if its a requirement you cannot deny here is what first comes to my mind:
Use the 'S * * *' instead of 'P * * *' (unless you are using ITS/J2EE and letting people access using HTTP(S)) , this will ensure that people are able to access only SAP protocol and not any other protocol
Use the following link to understand options of saprouter table.
http://help.sap.com/saphelp_47x200/helpdata/en/4f/992dfe446d11d189700000e8322d00/frameset.htm
Also,
It will be a good idea to allow access only to a particular IP Address i.e. the SAP Application Server instead of the entire IP range.
instead of
S * * *
something like:
S * <sap server ip address> *
Regards,
Siddhesh
Maybe you are looking for
-
Regarding Table View In visual Composer
Hi All, I am using Visual Compsoer 7.0. I have a table in my iview. When i go to the layout tab and right click the table. I cant see the options like "CUSTOMIZE TOOLBAR", where i can insert a row in my table. How can i have this option in VC 7.0? Re
-
Adding JornalEntries from GetObjectFromXml
Hi everybody, i'm receving this message when Adding journal entries loaded by GetObjectFromXml: "You cannot edit totals in system currency JDT1.SYSCred line 1". Seems to be the same error in this thread.... Re: GetBusinessObjectFromXML doesn't work w
-
Dear PM Gurus, for one my client going to rollout, how we have to do the plant maintenance module and what parameters have to be consider, how to assign the different number ranges? for example he using 1000 plant its already implemented and now he g
-
Canon S9000 Profiles for LR1.1
I only use Canon paper/ink with this device but does anyone know where I can get profiles for this printer ? The only one included with the Vista driver is BJ Colour Printer Profile 2000. Ian
-
I get an error message (F3-F200-0002 message) Toshiba C675-S7318
I get an error message (F3-200-0002) when my computer boots up, then it advised that press ok and error occurred and shuts down my computer C675-s7318 need help