Configuration printer CANON LPB6020

Hi Everybody!
Who can help me through with installing my new printer (Laser) Canon LPB6020, please?
I just bought the laser printer CANON LPB6020 in Geneva, in a very famous commercial store. But... Impossible to install it:
1. connexion USB: Canon LPB6020
2. System Preferences / Printers / Add a printer / Canon LPB6020
3. Canon LPB6020 appears on my Mac screen. I is asked for configuring Canon LPB6020: ... but, LPB6020 software IS NOT in the list provided by Mac.
IMPOSSIBLE TO CONTINUE !!!
In Canon website, I downloaded the software for Mac, but I can't open it. Mac doesn't allow to open this installer.
I wrote to CANON assistance... and I'm waiting for an answer for long...
If a MAC user can help me please....
Thank you in advance
Amelkis

Amelkis wrote:
First, in SYSTEM PREFERENCE of my Air Book, for adding my new printer, CANON LPB6020 (connected with USB)...
In the CONFIGURATION window posts the following remark: "the software for this printer is no available at Apple. Please contact the manufacturer for getting the latest software".
Canon does not provide the CAPT driver used by this model to Apple. So that is why you get the message that you must get it from the manufacturer (Canon).
Amelkis wrote:
So.... I go in CANON website / Assistance /downloading software LBP6020 for Mac OSX 10.9 version...
I download "Mac_AutoShutdownTool_V100_uk_EN"
I don't even see this utility on the Canon Australia web site but it's not the driver you need. Here is a link to the Canon CAPT v3.66 driver for your LBP6020
http://support-au.canon.com.au/contents/AU/EN/0100420705.html
After you download this driver and run the installer, you will get many models of Canon LBP in the Printer Software window and your LPB6020 will be one of them.

Similar Messages

Im trying to configure my printer 'Canon PIXMA MX3170' - however, I get Error during installation

Im trying to configure my printer 'Canon PIXMA MX3170' -
I followed the following steps mentioned on some site:
"Follow below steps to setup Canon MG3100 printer to wifi using WPS function (by a button push on the wireless router/access point)
Press and hold maintenance button on printer. (button with screw driver and cutting pair symbol)
Now the LED should flash as '_'
Press and hold 'Fit to Page" button, now LED should flash as single dash moving vertically.
Once the LED flash is confirmed, press and hold WPS button on router/access point for about five seconds.
Printer should stop the flashing and LED should be back to normal displaying '1'.
This completes the setup and you are ready to use your printer wireless ".
However,
1.LED on my printer flashes 1-2-3-E instead of a steady 1.
2. Error message during installation : "An error occurred while communicating with the printer"
3. Im using a netgear router - and I don't know what is an access point and how to configure it for the printer.
4. I think I pressed the right button - (WPS button) - button with symbol having a tower emitting waves.
My installation as a result - failed. Need your help.
Thanks,
Aditya

Hi Aditya!
Welcome to The Canon Forums, and thank you for your inquiry! We appreciate your participation, however we need to let you know that your product seems to be a model that is not supported by our team here at Canon USA. The Canon Forum is hosted and moderated within the United States by Canon USA. We are only able to provide support for Canon products manufactured for and used within the US market. If you live outside the United States, please click here and select your country or region for your support needs. Feel free to discuss Canon products sold outside of the United States, but please be aware that you will not receive support directly from Canon USA.

How to connect my mac book pro to network printer Canon IR 2010f?

I'm desperate to know how to connect my Mac book Pro to network printer Canon IR 2010f. This printer has an independent system, therefore, no need a PC to be on, in order to print. But this printer is a network printer. Help me please.

The Canon UFR2 v2.20 driver for Mac OS X does not list the iR2010F as a supported model. The same is so for the Canon PS driver so I therefore believe this model is PCL5e only.
What you should do is open Safari and type the IP address of the iR2010F. This will connect to the internal web page of the copier and from the provided pages you should be able to see what printer languages are supported.
If it only lists PCL then you will be able to print to this copier using the Generic PCL driver included with 10.6.
So if you open Print & Fax, click + to add and then select IP > LPD for the protocol you can then enter the IP address of the iR2010F and leave the queue name blank. For the name you can change that to iR1020F and for the Print Using, select Generic PCL Laser Printer.
One note with regards to this driver. It is defaulted to 300dpi so you will need to open the print dialog when you do print and change the resolution to 600dpi to get better print quality.

Hello! I have a printer,Canon MP250 and I bought a new MacBookPro with Maverick and I cannot work this printer

Hello! I have a printer,Canon MP250 and I bought a new MacBookPro with Maverick and I cannot work this printer with the driver that came with the printer and I've tried to find an update but with no success, can you help me?
Thanks!!

you can try resetting the network settings in settings or you can try doing a reset - hold down the home/power button together until you see the apple logo and then release. Then wait for the phone to boot back up. You won't lose any data.

HT5676 my macpro (10.6.8) refused to install wireless printer (canon pixma MG4260). Whenever i tried to install, it keeps saying 'internal error number 12'. Please help!! and what does internal error got to do with installing a printer?

my macbook pro (10.6.8) refused to install wireless printer (canon pixma MG4260). Whenever i tried to install, it keeps saying 'internal error number 12'. Please help me!! and what does internal error got to do with installing a printer?

my macbook pro (10.6.8) refused to install wireless printer (canon pixma MG4260). Whenever i tried to install, it keeps saying 'internal error number 12'. Please help me!! and what does internal error got to do with installing a printer?

MacBook Pro won't detect network printer Canon MF4150

I have a multifunction printer, Canon MF4150, hooked upto a PC Desktop and I have enabled printer sharing. The printer is detected and works fine on my PC Laptop. However, when I try installing it on my 13" MacBook Pro, the **** thing won't show up. It doesn't show up under the Windows category of Print and Fax so I tried to set it up the way Apple has suggested in their support section. It asks you to go to advance and input the IP address and location of the printer and then select the printer driver. I would post the link but I conveniently can't find it right now. The printer driver is obviously not listed on the list, so I go to the Canon website and download a mac version of the driver and install it. When I check to see if it's on the list now, it says MF4360-MF4390, but not MF4150. I thought I had installed the wrong one but I downloaded and installed it again, and I got the same problem. Anyone have this printer or have a similar problem? Another way to hookup this printer would be much more convenient, is there anyway that the Window tab could detect it? Any help is appreciated!

The warranty must be close to running out. Take it ASAP to the Apple Store or AASP and have it checked.

Staple problem with printer Canon iR-ADV 8205

Hello,
I work with output designer 5.7 and when i try use option staple with canon printer Canon iR-ADV 8205 the document is print and staple, but the pageconter is equal zero. What can i do for print my document correctly?
Thanks Julio.

I FINALLY SOLVED THE PROBLEM. YOU CAN PRINT IN BOTH SIDES IN THE SAME DIRECTION IN LANDSCAPE IF YOU PUT IN THE Binding Location OPTION Short Edge (Left).
THANKS ANYWAY

How can i connect my printer canon pixma mg7150

Hello,
I don't find the good driver for my printer CANON PIXMA MG7150, and i use a usb cable.
Is it good ?
Thanks

I have been setting up the same printer this week, with a USB cable to my iMac. I have taken Mac printer drivers from the Canon site. Here is a link that I used.
http://www.canon.co.uk/Support/Consumer_Products/products/Fax__Multifunctionals/ InkJet/PIXMA_MG_series/PIXMA_MG7150.aspx?type=download&softwaredetailid=tcm:14-1 091005&os=OS%20X%20v10.9&language=EN
Apple have notified that they have newly updated printer drivers for this printer, which you can download if you have the other drivers in place.
Hope this helps.

How to enable report print or configure print server

Hi All.
Currently using lastest Apex version (4.1.x) with 11g XE.
Where can i find info, example etc. to enable report printing? When i access this attribute section, i get a red warning message saying there is no print servver configure.
Regards, Luis ....!

Here is a whitepaper that should answer your questions..
http://www.oracle.com/technetwork/developer-tools/apex/application-express/configure-printing-093060.html
Thank you,
Tony Miller
Dallas, TX

Please help me, How to connect my printer Canon pixma MP160 to my mac OS X Yosemite?

please help me, How to connect my printer Canon pixma MP160 to my mac OS X Yosemite?

You do not need the Setup Assistant; in fact, you do not need any software on an external hard drive. I have two LaCie's; I erased the drive as soon as I plugged it in. You will need to format it anyway because most hard drives come Windows formatted. So, if you only want to use it with the Mac, highlight it in Disk Utility and choose Mac OS Extended (Journaled) as the format and the GUID Partition scheme under Options. While doing that, it will erase the drive (and get rid of the LaCie software) - once finished, your drive is ready to use for Time Machine or any other backup plans you have for it.

What r spool requests and procedure of configuring printer in SAP

Hello Experts,
i hv one question? wt r spools and wt are spool requests ? what are they used for? also i need a step wise step procedure for configuring printer in SAP . My email id is [email protected] . Requested to revert at earliest as this is very urgent.
points guaranteed.
regards,
Somya

hi
whenevr u print ur output , spoll no. will be generated.
Go to TCode Sp01/SP02 and give the spool No. which u generated and there u can find ur spool with outputlist,
The basic transaction to set an printer within an SAP system is SPAD.
I would recommend you to access the online SAP help at the following URL where you will find detailed information on how to set printers :
http://help.sap.com/saphelp_46c/helpdata/en/d9/4aa45b51ea11d189570000e829fbbd/frameset.htm
regards
ajai

I have a printer canon mp495 and I'm trying to connect it to my iPad. But my iPad can find it the printer. Do I have to reset the printer or what app do I use?

I have a printer canon mp495 and I'm trying to connect it to my iPad. But my iPad can find it the printer. Do I have to reset the printer or what app do I use?

Printopia is Macintosh-only. <Printopia for Macintosh>
Another program that is available in both PC and Mac versions is FingerPrint. <FingerPrint>
For either program, your computer must be on and awake any time you want to print.
Fred

Lightroom 5.7 with printer canon ipf 6450

Hi, i've a problem with lightroom 5.7; i'm unable to print with the print module on my canon ipf 6450 (can't manage the colors by lightroom. i'm using Mac Os X 10.9.5. No issues at all with CS6 to print!

Hi Jim
Here a screen shot:
Mit freundlichen Grüssen
Pascal Gai
Chasseralstrasse 15
3212 Kleingurmels
www.pascalgai.com
Am 30.12.2014 um 15:03 schrieb JimHess <[email protected]>:
Lightroom 5.7 with printer canon ipf 6450
created by JimHess in Photoshop Lightroom - View the full discussion
What is preventing you from managing the colors using Lightroom?
If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7052908#7052908 and clicking ‘Correct’ below the answer
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7052908#7052908
To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following"
Start a new discussion in Photoshop Lightroom by email or at Adobe Community
For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

Steps to configure printer

Hi,
I need to configure Printer for the SAP Server
Please let me knwo the link for any documents

Hi Balaji,
It pretty simple, First make sure that you have configured the printer at os level and system can identfiy the printer at os level
then go to spad and create lp01 and just select what type of printing you want like frontend printing or local printing.
If you select front end prinitng the you can take the print in any system where printer is configured.
Reward points if helpfull.
Regards,
Vamshi.

HT2250 I have an Apple network utility that with the previous printer (Canon PIXMA iP 5000) found the printer on the Network for use on a wi fi system but a newish printer (Canon MG6150) does not show up as Bonjour. Is that correct?

I have an Apple network utility that with the previous printer (Canon PIXMA iP 5000) found the printer on the Network for use on a wi fi system but a newish printer (Canon MG6150) does not show up as Bonjour. Is that correct?
paul.kelly

Hi Steve,
No expert, but since nobody else has piped in...
Did you setup the DNS Server IP?

Configuration printer CANON LPB6020

Similar Messages

Maybe you are looking for