Configuration required in Cat 4006 to forward errors to syslog server

Hi,
I have setup a Kiwi syslog server. I want to configure in my Cat 4006 switch to forward the following messages to my syslog server
1. configuration changes
2. Vlan creation /modification
3. Power supply failures/module failures/temperature
4. When the processor utlization exceeds more than 75% , it should send a alert message to syslog server
5. Switch restart
6. Trap for any changes in Uplink ports only. There are 4 uplinks to other Switches from 4006. If any problem with these ports (uplink), it should send message to syslog server , not for all ports
Thanks in advance
Raju

Hi
I feel this link will be of some help to u in configuring different severity levels for different facilities available.
http://www.cisco.com/en/US/partner/products/hw/switches/ps663/products_configuration_guide_chapter09186a00800d81c8.html
By default for abnormal temp conditions u will get logs in the syslog server if u have already pointed the logs to the syslog server..
regds

Similar Messages

How to configure IPS 4240 - K9 to send log file to syslog server

I am looking for the commands in how to configure IPS 4240-k9 to send log file to SYSLOG server. If anybody has or came across similer issue please advice.
Thanks in advanced.

Ali -
I am sorry to tell you, but the Cisco IPS Sensors do not send Syslog messages. Your only options for sending signature event information are:
SDEE (an TLS Encrypted XML formatted message) the sensor is the SDEE Host and your event receiver (MARS, IME, Intelitactics, etc) is the client.
SNMP Traps - You need to set the "Action" on each signature you want the sensor to send a trap.
- Bob

Error during Checking Network Configurations Requirements in RHEL3 VM

Hi,
I have a Red Hat Enterprise Linux Image Virtual Machine on my desktop which uses Fedora Linux. I have set this up using VMplayer.
I need to install Oracle 10g on the RHEL VM.
As the RHEL VM does not have X Windows, I am connecting to it from the Fedora Linux to do the installation.
During the Product-specific Prerequisite checks:
Checking Network Configurations Requirements throws an error,
Please find it below:
Actual Result: Unknown Host Exception has Occured :rhel3vm:rhel3vm
Check complete: The overall result of this check is: Not executed <<<<
Recommendations: Oracle supports installations on systems with DHCP-assigned public IP addresses. However, the primary network interface on the system should be configured with a static IP address in order for the Oracle software to function properly.
The Fedora Linux gets the IP address from the DHCP and allocates an IP address to the VM.
However, when we set both of them as static and the problem still persists, and also when we set the fedora as dynamic and RHEL VM as static, the issue is not resolved.
Any help will be truely appreciated. Thank you.

We were running a non-DHCP (static IP) configuration and ran into this issue. We discovered that the hostname and FQDN were not correctly specified in the /etc/hosts file.
Fixing the hosts file to correctly reference the IP resolved the issue.
Hope this helps...
-john

Oracle 10g Installtion error Network Configuration requirements ... failed

Checking Network Configuration requirements ...
Check complete. The overall result of this check is: Failed <<<<
Problem: The install has detected that the primary IP address of the system is DHCP-assigned.
Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses; However, before you can do this, you must configure the Microsoft LoopBack Adapter to be the primary network adapter on the system. See the Installation Guide for more details on installing the software on systems configured with DHCP.

Are you installing Oracle 10G R2? If this is the case then for DHCP network environments, you need to create a Microsoft loop back adapter.
Microsoft Loopback Adapter creation:
===========================
Step 1: Programs -> control panel -> Add Hardware.
Step 2: In the Add Hardware wizard. Click 'Next' and select 'Yes, I have already connected the hardware'. option and click on 'Next'.
Step 3: Select the last option 'Add a new hardware device' from the 'Installed hardware' window and click on 'Next'.
Step 4: Select the last option 'Install hardware that I manually select from the list (Advanced) and click on 'Next'.
Step 5: Select 'Network adapters' in 'Common hardware types' list and click on 'Next'.
Step 6: Where you can see 'Microsoft loopback adapter' on the right hand side of the frame.
Step 7: proceed with all default installation and then try installing Oracle.
I hope this will suffice.
Thanks
Venugopal

How to activate Forward Error Handling in SRM

Hello Gurus,
I got an requirement to activate Forward Error Handling in SRM. I have searched on SDN but didn't find appropriate answer on it.
Even I found some link: PI/XI: Forward Error Handling (FEH) for asynchronous proxy calls with the use of Error and Conflict Handler (ECH)
It explains me some points like activating FEH from SRM in SPRO. I have activated the same, plz check the screen shot:
It also follows some development for the same.
Here my concern is, should I follow this document? Does it applicable to all to all the scenarios?
Step 8: it assign object id and type what does it mean...
Does any one can explain me in detail..... Please provide me any document to configure the FEH in SRM.
I am trying to implement FEH in my SRM system. So that when even XML fails due to error, I should be able to reprocess/restart it with some editing to the XML.
My receiver interface for XML is PurchaseRequestERPSourcingRequest_In
I think this is standard one and no need to make any custom code for it. SAP has all ready given solution for it with some Configuration.
I have made some configurations like:
The view FEHV_ACTIVE must have the status active.
In transaction /SAPPO/LOGSYS , the logical system must be defined for the software component SRM-EBP-ESA .
As stated in in the link :
http://esworkplace.sap.com/socoview%28bD1lbiZjPTAwMSZkPW1pbg==%29/render.asp?id=2BAABCB0D30111DC2B8D000F20FCB6A9&fragID=…
Also I have made some configuration according to the Note: 1973768 - No reprocess option is available in FEH for failed in XML in SRM
Resulted, the “Process” button get activated in the XML Post Processing screen.
But can I reprocess my XML with edited value from there..?
All the configuration part of PI is already done .
I wanted to know about the FEH Part. what are the steps i am missing or where i am going wrong ?
Please let me help.
Thanks
Regards
Karan

Dear Raz,
I have gone with above mentioned note, it explains about creating Custom Proxy and configuration with PI scenario. Even the link in my previous post, explains about the custom proxies and configuration..
I think I should must be descriptive about my issue.
I am trying to implement FEH in my SRM system. So that when even XML fails due to error, I should be able to reprocess/restart it with some editing to the XML.
My receiver interface for XML is PurchaseRequestERPSourcingRequest_In
I think this is standard one and no need to make any custom code for it. SAP has all ready given solution for it with some Configuration.
I have made some configurations like:
The view FEHV_ACTIVE must have the status active.
In transaction /SAPPO/LOGSYS , the logical system must be defined for the software component SRM-EBP-ESA .
As stated in in the link :
http://esworkplace.sap.com/socoview%28bD1lbiZjPTAwMSZkPW1pbg==%29/render.asp?id=2BAABCB0D30111DC2B8D000F20FCB6A9&fragID=…
Also I have made some configuration according to the Note: 1973768 - No reprocess option is available in FEH for failed in XML in SRM
Resulted, the “Process” button get activated in the XML Post Processing screen.
But can I reprocess my XML with edited value from there..?
Can any one tell me, what are the steps I am missing here. As this is my first time to implement FEH, I am confused.
Please let me help.
Regards,
Chandan

NAT forwarding error?

I have an Airport Extreme Base Station which I'm running with 3 pcs and a 12 inch powerbook - I used the powerbook to configure it. Everything works fine, except for 2 problems at specific online locations, which I suspect may be related. My online bridge club will not let me host a table because I have a "NAT forwarding error". I have read up and understand what that is, but the instructions I can find to fix it aren't very clear - can anyone give me better ones? The instructions I do have say I will have to set up a static address for each computer - my ISP requires a dynamic address. Is there a way round this? Also, the customer service page at my ISP's web site won't load - I get an Internal Service Error 500 message. Tech support at the ISP told me that "sometimes routers act like firewalls" and had me plug the modem directly into my computer - it then worked. Apple tech support said they'd never heard of such a thing. Could this also be a NAT forwarding error?
Power Book G4, Airport extreme, 3 PCs Mac OS X (10.4.6) Windows XP on the PCS
Dell Latitude CPx Windows XP Pro

The instructions I do have say I will have to set up a static address for each computer - my ISP requires a dynamic address. Is there a way round this?
The AirPort Extreme base station (AEBS) will continue to get it's address from your ISP via DHCP. You will need to give your computer a local static IP address. You will find the information you need in Steve Newstrum's user tip "How do I use Port Mapping (Part I)".

Network configuration requirements 10g

hi every body
i am trying to install oracle 10 g db using Vmware on Centos 5.
i have performed all the steps as described in installation guides but when OUI is checking pre reqs it is giving this error
"checking network configuration requirements" and then "not executed"
can somebody please specify these requirements ???
in case i want to move forward it says that you can expect some problems during installation ???
thnx in advance .
Regards

do you have a network setup ? Can you ping other servers from the VM ?
You can run a database without a network. The listener configuration may fail, but you can easily re-run it later. You could just do the install, and see if anything else fails. If it does, the error may give more information.
Or you can turn off the check using
runInstaller -ignoreSysPrereqs

Error accessing Name Server Configuration

Hello,
I have installed WebAS 6.40 SP11 and deployed JDI SP11 on a single stand-alone machine, which is configured as Landscape and Name Server. When I try to access the Name Server Configuration in the DTR I get a "Server not found" error.
The URL is http://<server>:<port>/dtr/system-tools/administration/NameServerConfiguration
Where can I search for the reason? Any hints?
Regards,
Bjoern

Hi Bjorn,
     As of SP11, the name server configuration requires SSL to be accessed. Thus you need to set up your JDI box for SSL communications then the address would be:
https://<server>:<SSL port>/dtr/system-tools/administration/NameServerConfiguration
SP11 is the first SP to require this SSL access. Note that the communication between your JDI and the Name Server does NOT need to be SSL. You can use the same configuration you used before. Only the access to the name server configuration needs to be SSL.
     Hope this helps,
       --Greg

Checking Network Configuration requirements

Hi
I am getting the following error while installing oracle database 11gR1
Checking Network Configuration requirements ...
Check complete. The overall result of this check is: Not executed <<<<
Recommendation: Oracle supports installations on systems with DHCP-assigned public IP addresses. However, the primary network interface on the system should be configured with a static IP address in order for the Oracle Software to function properly. See the Installation Guide for more details on installing the software on systems configured with DHCP.
========================================================
OS: SUSE 10 SP2
My network is configured to static ip, and DHCP is disabled. I don't know what else can be the reason, please, give some pointers...
regards
RF

oracle@bitmatrix:~> /sbin/ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:13:8F:B1:A4:0D
inet addr:192.168.102.70 Bcast:192.168.102.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:102126 errors:0 dropped:0 overruns:0 frame:0
TX packets:1323 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:7368939 (7.0 Mb) TX bytes:83864 (81.8 Kb)
Interrupt:177 Base address:0xcc00
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:84093 errors:0 dropped:0 overruns:0 frame:0
TX packets:84093 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:22063435 (21.0 Mb) TX bytes:22063435 (21.0 Mb)

Cat 4006 S3 - Attached hosts Net access very slow prior to reboot

I have a CAT 4006 sup III running 12.1(11b)EW1 with a number of servers attached. Users started having problems accessing servers. After investigating all the impacted servers were connected to the same switch. The switch was appeared to be operating normally. Show proc cpu, show proc mem, show logging, and ping tests all normal. Warm booted switch and asics on sup failed bootup diag. Cold boot of the switch got it back up and running. Cisco Tac reviewed the post problem sh tech with no findings.
Any ideas?

No L2 loops and it was a hopefully isolated incident. We have to switches that are identical in hardware and IOS and only one was impacted.
clients of systems attached to the switch would have intermittently slow or non existent access to the host systems. Problems included saving files on network drives, email down, very slow or failed logins, application launches were slow or failed.
No messages were showing up in the switch log, let alone messages referred in the tech note. We have had asic issues on line cards in the past. Those instances were on different switches and created volumes of errors.
Layer 2 seemed fine. Pings were worked without fail. Console broadcast messages from host systems on the impacted switches made it out to clients.
Keep thinking it wasn't a switch problem but the reboot did fix the issue.
I will be replacing the sup card and doing a IOS upgrade this weekend.

Why do i get a daq hardware configuration required window when trying to run the daq solution wizard?

i have recently installed the ni 4552 for pci dynamic signal analyser, and am attempting to configure my system and teach myself labview. when attempting to run the daq solution wizard i am presented with the daq hardware configuration required window.
Attachments:
DAQ_Hardware_Configuration_Required.ppt ‏38 KB

hi brian, thanks for your help. i have recently received version 6.1, and done a complete re-install. i have also downloaded the latest ni daq (6.9.2) and ni dsa (6.11) versions and installed them, but still i get the same error message when trying to open the solutions wizard (please see attached powerpoint presentation).
upon selecting the "go to ni daq config utility" option MAX opens. everything appears to be in order (device passes test, test panels run ok and virtual channels are configured correctly). i am unable to go any further.
i would appreciate any guidance that you are able to give me in this matter. many thanks in advance of your help.
best regards,
ben halkon

What are the backend configuration required for photo upload from portal?

Hi all,
When i am trying to upload the photo from portal it is giving error
can not archive the photo
we are using portal 7 and ecc 6.0
I want to know
What are the backend configuration required for photo upload from portal
Can any but help me out
Rajendra

Hi,
Are you using the standard iview. If that's the case you need to configure in the backend. Meaning you need to store the photo in the Org management(HR) which the HR functional guys will do. You just need to add the iview to your role.
Let me know if you require further informationn.
Award points if helpful.
Cheers,
sathya

Hi, I am unable to install new itunes version to windows 7 PC. It requires application support and gives windows error 2. I have tried to save on desktop and run as administrator but errors remains, what other options do I have

Hi, I am unable to install new itunes version to windows 7 PC. It requires application support and gives windows error 2. I have tried to save on desktop and run as administrator but errors remains, what other options do I have?

Hello, hanliefromzaf.
Thank you for visiting Apple Support Communities.
Here is an article that I would recommend going through when experiencing this issue.
iTunes for Windows: Unable to install or open
http://support.apple.com/kb/ts5376
Cheers,
Jason H.

How to Setup Forward Error Handling in PI Scenarios. Can you help me with the same with screen shots if possible?

Dear all
How to Setup Forward Error Handling in PI Scenarios. Can you help me with the same with screen shots if possible?
Thanks
Regards
karan

Hello
These are the following errors
1. Trace level="1" type="T">no interface action for sender or receiver found</Trace>
2. <Trace level="1" type="System_Error">Application-Error exception return from pipeline processing!
3.
<Trace level="1" type="T">Application Error at Receiver... => ROLLBACK WORK</Trace>
<Trace level="1" type="T">System Error at Receiver... => ROLLBACK WORK</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST" />
<Trace level="1" type="System_Error">Application-Error exception return from pipeline processing!</
Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>Trace level="3" type="T">Error of the prevous version:</TraceTrace level="3" type="T">Error ID APPLICATION_ERROR</Trace>
tThere are repeating errors also.
TThanks
Regards
kkaran

Forward Error Correction

I'm trying to find a way to implement Forward Error Correction (FEC) in Java, and if possible, find a code that someone has wirtten b4.
Can any1 plz help me? I need this FEC in a one way communication.

BTW, I want this in native Java (not C, like swarmcast)

Configuration required in Cat 4006 to forward errors to syslog server

Similar Messages

Maybe you are looking for